Electronics Modules

6 products


  • CJMCU-ADS1115 16-Bit Precision Analog-To-Digital Converter AdC 4-Channel Development Board Module-garmade.com

    CJMCU-ADS1115 16-Bit Precision Analog-To-Digital Converter AdC 4-Channel Development Board Module

    1. The portable instrument is automatically powered off after conversion and greatly reduces current consumption during idle periods2. Features: easy to implement, high precision, low current consumption, multi-mode conversion3. Power supply voltage: 2-5.5v4. Working temperature: -40 to 125 degrees celsius5. Programmable data rate: Transmission via I2C compatible serial interface6. Single mode: Automatic shutdown with onboard reference and oscillator7. Size: about 16 x 28mm8. Weight: about 2.5g

    €6,50

  • 4 inch Touch LCD Shield for Arduino-garmade.com

    4 inch Touch LCD Shield for Arduino

    Features1. Resistive touch screen TFT LCD, 4inch, 480x320 resolution2. Standard Arduino interface, compatible with development boards like : Arduino UNO, Leonardo, UNO PLUS, NUCLEO, XNUCLEO3. Onboard stand-alone touch controller, better touching than solutions that use AD pins directly for touch control4. PWM backlight control, allows to adjust the backlight to a comfortable level5. Micro SD slot, provides an easy way to store photos for displaying6. Controlled via SPI, only a few Arduino pins are used7. Comes with STM32 and Arduino examples, convenient for portingKey Parameters1. LCD Type: TFT2. LCD Interface: SPI3. LCD Controller: ILI94864. Touch Screen Type: Resistive5. Touch Screen Controller: XPT20466. Colors: RGB, 65K colors7. Resolution: 480x320 (Pixel)8. Aspect Ratio: 8:59. I/O Voltage: 3.3V/5VWiki : www.waveshare.com/wiki/4inch_TFT_Touch_Shield

    €41,18

  • Waveshare Adapter Board for Arduino & Raspberry Pi-garmade.com

    Waveshare Adapter Board for Arduino & Raspberry Pi

    OverviewArduino is a massive ecosystem, if there is a way for the Raspberry Pi GPIO interface to adapt to Arduino pinouts, it is possible to use the Pi together with vast Arduino shields and hardware/software resources. The ARPI600 is just intended for this.What is more, the ARPI600 also support XBee modules, make it easy to add wireless feature to your great project.Supported Pi1. Raspberry Pi 1 Model A+2. Raspberry Pi 1 Model B+3. Raspberry Pi 2 Model B4. Raspberry Pi 3 Model B5. Raspberry Pi 3 Model B+ARPI600 Features1. Compatible with Arduino UNO, Leonardo, easy to connect with various Arduino shields2. XBee connector for connecting various XBee modules3. Sensor interface for connecting various sensors4. Onboard USB TO UART for serial port debugging, also can be configured as XBee USB adapter5. Onboard ADC, 10 bit, 38KSPS, 11 channels (6 channels for Arduino interface, 5 channels for sensors)6. Onboard RTCWhat is on the ARPI6001. Arduino connector: For connecting Arduino shields2. ICSP interface: Arduino ICSP3. XBee connector: For connecting XBee communication modules4. Sensor interface: For connecting sensors5. Raspberry Pi connector: For connecting Raspberry Pi6. USB TO UART7. TLC1543: AD converter8. PCF8563: RTC9. CP210210. 32.768KHz crystal: For RTC11. Power indicator12. XBee state LED13. XBee and Arduino interface RESET button14. XBee EASYLINK button15. RTC battery holder: For CR1220 button battery16. TLC1543 reference voltage configuration jumper17. RTC jumper18. UART jumper- When connecting P_RX and CP_TX, P_TX and CP_RX respectively, USB TO UART is connected to Raspberry Pi serial port- When connecting XB_RX and CP_TX, XB_TX and CP_RX respectively, USB TO UART is connected to XBee serial port- When connecting XB_RX and P_TX, XB_TX and P_RX respectively, Raspberry Pi serial port is connected to XBee serial port19. Arduino AD selection jumper- Short 2 and 3: Arduino A0-A5 as AD input- Short 1 and 2: Arduino A0-A5 as digital control20. Arduino I2C selection jumper- Short the jumper : Arduino A4-A5 as I2C control (the A4-A5 of Arduino AD selection jumper should be opened)21. Arduino SPI selection jumper- Short 1 and 2: Arduino D11-D13 as SPI control (default)- Short 2 and 3: Arduino D11-D13 as digital controlPackage Contents1. ARPI600 x 12. USB type A plug to mini-B plug cable x 13. RPi screws pack (2pcs) x 1

    €35,40

  • 2.8 inch Touch LCD Shield for Arduino-garmade.com

    2.8 inch Touch LCD Shield for Arduino

    Features1. Resistive touch screen TFT LCD, 2.8inch, 320x240 resolution2. Standard Arduino interface, compatible with development boards like : Arduino UNO, 3. Leonardo, UNO PLUS, NUCLEO, XNUCLEO4. Onboard stand-alone touch controller, better touching than solutions that use AD pins directly for touch control5. Micro SD slot, provides an easy way to store photos for displaying6. Controlled via SPI, only a few Arduino pins are used7. Backlight adjustable by program, lower power consumptionKey Parameters1. LCD Type: TFT2. LCD Interface: SPI4. LCD Controller: HX8347D5. Touch Screen Type: Resistive6. Touch Screen Controller: XPT20467. Colors: RGB, 65K colors8. Resolution: 320x240 (Pixel)9. I/O Voltage: 3.3V/5VWiki : www.waveshare.com/wiki/2.8inch_TFT_Touch_Shield

    €26,86

  • 3.5 inch Touch LCD Shield for Arduino-garmade.com

    3.5 inch Touch LCD Shield for Arduino

    Features1. Resistive touch screen TFT LCD, 3.5inch, 480x320 resolution2. Standard Arduino interface, compatible with development boards like : Arduino UNO, 3. Leonardo, UNO PLUS, NUCLEO, XNUCLEO3. Onboard stand-alone touch controller, better touching than solutions that use AD pins directly for touch control4. PWM backlight control, allows to adjust the backlight to a comfortable level5. Micro SD slot, provides an easy way to store photos for displaying6. Controlled via SPI, only a few Arduino pins are used7. Comes with STM32 and Arduino examples, convenient for portingKey Parameters1. LCD Type: TFT2. LCD Interface: SPI3. LCD Controller: ILI94864. Touch Screen Type: Resistive5. Touch Screen Controller: XPT20466. Colors: RGB, 65K colors7. Resolution: 480x320 (Pixel)8. Aspect Ratio: 8:59. I/O Voltage: 3.3V/5VWiki : www.waveshare.com/wiki/3.5inch_TFT_Touch_Shield

    €34,22

  • Waveshare RS485 CAN Shield, RS485 CAN Shield Designed for NUCLEO/XNUCLEO-garmade.com

    Waveshare RS485 CAN Shield, RS485 CAN Shield Designed for NUCLEO/XNUCLEO

    OverviewThe RS485 CAN Shield will easily enable RS485/CAN communication functions for your NUCLEO/XNUCLEO Arduino boards.Features1. Arduino standard interfaces, compatible with Arduino boards like Arduino UNO, Leonardo, NUCLEO, XNUCLEO- When using with Arduino UNO, Leonardo, the CAN function is unavailable due to hardware limitation2. RS485 function, onboard transceiver SP3485/MAX3485, 3.3V power supply3. CAN function, onboard transceiver SN65HVD230, 3.3V power supply

    €15,18

Login

Forgot your password?

Don't have an account yet?
Create account