Electronics Modules

OverviewThis is an OLED display HAT for Raspberry Pi, 1.3inch diagonal, 128x64 pixels, with embedded controller, communicating via SPI or I2C interface.Trying to add a control interface for your Pi? This compact display would be the ideal choice.Features1. Standard Raspberry Pi connectivity, compatible with and direct-pluggable onto Raspberry Pi 2B/3B/3B+/Zero/Zero W2. Optional interfaces: 4-wire SPI, 3-wire SPI, I2C, configured via onboard resistor3. 1x joystick (5-position), 3x pushbuttons, handy and useful4. Comes with development resources and manual (examples for Raspberry Pi/Arduino/STM32)Specifications1. Driver: SH11062. Interface: 4-wire SPI, 3-wire SPI, I2C3. Display color: blue4. Resolution: 128x645. Operating voltage: 3.3V

Read more less

Overview1. The PCF8591 AD DA Board features an 8-bit A/D Converter & D/A Converter PCF8591 with four analog inputs, one analog output and a serial I2C-bus interface.2. The PCF8591 AD DA Board features I2C pinheader on one side, and I2C connector on the opposite side. Hence, its more flexible to connect the board to your development system. The board also supports I2C cascading, allowing the use of multi module connected to the I2C bus at the same time by connecting the pinheader and connector.FeaturesPCF8591, I2C pinheader, I2C connector, Adjustable resistor, Analog input for A/Dconversion, Analog output for D/A conversion, Address pins jumper

Read more less

Overview1. The Analog Test Board is an accessory board includes an onboard Audio Power Amplifier LM386M, and two high-precision adjustable resistor used for adjusting input voltage level (0-3.3V, 2 channel), and a speaker for indicating the output voltage level by sound volume (1 channel).2. The board is ideal for testing AD/DA function that integrated in the MCUs, it also supports MP3 output, music playing, etc.FeaturesLM386M, speaker, high-precision adjustable resistor × 2, analog input/output

Read more less

OverviewThis low power audio module is based on WM8960, supports stereo encoding/decoding, supports sound recording, what's more, it can directly drive speakers to play music.Features1. Integrates high-quality MEMS silicon Mic, supports sound recording2. Onboard standard 3.5mm 4-segment earphone jack, allows sound recording via external earphones with Mic3. Onboard dual-channel speaker interface, directly drives speakers4. Supports common audio sampling rates such as 8/11.025/22.05/44.1/48KHz, etc.5. Supports sound effects such as stereo, 3D surrounding, etc.6. Comes with development resources and manual (STM32 examples for playing, recording)Specifications1. CODEC: WM89602. Operating voltage: 3.3V3. Control interface: I2C4. Audio interface: I2S5. Audio format: WAV6. DAC signal-noise ratio: 98dB7. ADC signal-noise ratio: 94dB8. Earphone driver: 40mW (16Ω@3.3V)9. Speaker driver: 1W per channel (8Ω BTL)

Read more less

Overview1. This is a small 1D/2D codes reader, by using the intelligent image recognition algorithm, it will decode the barcode or 2D code on paper or screen, fast and accurately.2. Through the onboard USB and UART interface, it can be directly plugged into a computer, or be easily integrated to kinds of devices due to its small form factor.Features1. Easy to use, requires no knowledges of image recognition2. Decodes various common 1D/2D codes such as Barcode, QR code etc.3. Onboard micro USB and UART serial port, allows to connect with computers or embedded devices4. Configurable via scanning configuration code5. Onboard light source, works in the darkSpecifications1. Operating voltage: 5V2. Operating current: 135mA (scanning), 58mA (standby), 2mA (sleep)3. Operating temperature: 0°C~60°C4. Operating humidity: 5%~95% (Non-condensing)5. Communication interface: UART, USB6. Decodes 1D codes: Codebar, Code 11, Code 39/Code 93, UPC/EAN, Code 128/EAN128, Interleaved 2 of 5, Matrix 2 of 5, MSI Code, Industrial 2 of 5, GS1 Databar(RSS)7. Decodes 2D codes: QR code, Data Matrix, PDF4178. Light source: white9. Scan angels: roll 360°, skew ±65°, pitch ±60°10. Field of view: 28° (horizontal), 21.5° (vertical)11. Dimension: 53.3mm x 21.4mm12. Package contents:- Barcode Scanner Module x1- USB type A plug to micro B plug cable x1- PH2.0 4Pin x1

Read more less

Features1. 3W high-power 850 infrared LED2. Onboard photoresistor, the ambient light detector3. Onboard adjustable resistor, for controlling the ambient light threshold of toggling the infrared LED4. Allows adding night vision function to cameras which feature embedded infrared filter :a) 100 degree field of view, two pieces of LED is required to get wider field of viewb) Supported devices : RPi Camera (E), RPi Camera (F), RPi Camera (H)How to Use1. Connect the Infrared LED Board to the camera PCB by screws2. The screw holes are used for both attachment and power supply3. Adjust the adjustable resistor to set a proper ambient light threshold, which toggles the infrared LED automatically4. When ambient light is lower than threshold value, the infrared LED is on, vice versaNote :1. Limited by the Raspberry Pi power supply, the 3W high-power infrared LED might cause the Pi to increase heating, heat sinks are suggested.2. Ideal imaging distance is within 3m. When the distance goes up to 6m, the night vision camera can just capture blurry outlines.

Read more less

Raspberry Pi Expansion Board, DC Motor / Stepper Motor DriverFeatures1. Supports Raspberry Pi A+/B+/2B/3B/3B+2. Freescale H-bridge driver MC33886, controls DC motors to turn in both directions3. Onboard 5V regulator, provides power to Raspberry Pi4. Onboard IR receiver, used for remote control robot5. Multi protection circuit, excellent stability- 2A self-recovery fuse, keep your Pi safe- Driver chip features Short-Circuit Shutdown for Large Output Current, Undervoltage Disable Function- Reversed polarity protection for motor output- Anti-reverse diode for power supply6. Power input range: 7V~40V7. Single motor output current: up to 5A8. Power supply current for Raspberry Pi: up to 2AWhats on Board1. Raspberry Pi Expansion Board on board resource2. Raspberry Pi GPIO interface: for connecting Raspberry Pi3. Motor screw terminal: for connecting motors4. External power input5. 74LVC4245AD: voltage level conversion chip, buffer device6. MC33886: motor driver chip7. LM2596-5.0: 5V regulator8. Power indicator9. Raspberry Pi power selection10. OFF: Raspberry Pi powers the Motor Driver Board11. ON: Motor Driver Board powers the Raspberry Pi12. 2A self-recovery fuse13. IR receiver14. Schottky diodes: protects the motor driver15. Power supply anti-reverse diodePackage Contents1. RPi Motor Driver Board x 12. RPi screws pack (2pcs) x 1

Read more less

Overview1. This is a 4 port USB hub for Raspberry Pi, provides more USB capability to your Pi, whats more, it features USB to UART converter for easy serial communication.2. It can work with various versions of the Pi, and the size of the board is designed to perfectly fit the Zero / Zero W.USB HUB HAT Features1. 4 USB Ports, compatible with USB2.0/1.12. Onboard USB to UART, convenient for Raspberry Pi serial debugging3. Onboard multi indicators, for monitoring the status of power, USB to UART, and each USB portWhat is on the USB HUB HAT1. Raspberry Pi GPIO interface: For connecting Raspberry Pi2. USB to UART: For controlling the Raspberry Pi via serial terminal3. USB HUB interface (bottom): For connecting the HUB to the Raspberry Pi USB port- Raspberry Pi Zero / Zero W: Connected via Micro USB connector- Raspberry Pi B+ / 2B / 3B / 3B+: Connected via Micro USB cable4. USB extended ports: USB1~USB45. USB port indicators: dedicated indicator for each USB port, D1~D4 for USB1~USB4 respectively6. Power indicator7. USB to UART indicator8. FE1.1S: USB HUB chip9. 12MHz crystal10. CP2102: USB to UART converterSpecifications1. Operating voltage: 5V2. Dimension: 65mm * 30mm3. Mounting hole size: 3.0mm4. Package contents:- USB HUB HAT x1- Micro USB connector x1- Micro USB cable x1- RPi screws pack (2pcs) x1

Read more less

NB-IoT HAT for Raspberry Pi, Based on SIM7020E, B1/B3/B5/B8/B20/B28 BandsApplicable Region1. SIM7020E is mainly applicable in Europe, Asia, Africa, Australia.2. Please check the supported bands according to your local service provider when placing order.OverviewThis is an NB-IoT (NarrowBand-Internet of Things) HAT for Raspberry Pi, controlled via serial AT commands, supports communication protocols like LWM2M/COAP/MQTT, etc. Due to the advantages of low delay, low power, low cost, and wide coverage, it is the ideal choice for IoT applications such as intelligent instruments, asset tracking, remote monitoring, and so on.Features1. Raspberry Pi connectivity, compatible with any revision2. Support communication protocols such as LWM2M/COAP/MQTT/TCP/UDP/HTTP/HTTPS, etc.3. Onboard USB interface, for power supply OR debugging4. Breakout UART control pins, to connect with host boards like Arduino/STM325. Onboard voltage translator, 3.3V by default, allows to be switched to 5V via onboard jumper6. SIM card slot, supports NB-IoT specific card7. 2x LED indicators, easy to monitor the working status8. Baudrate: 300bps~921600bps (115200bps by default)9. Control via AT commands (V.25TER, 3GPP TS 27.007, and SIMCOM AT Commands)10. Come with development resources and manual (examples for Raspberry Pi/Arduino/STM32/Python)Communications Specifications1. Band- FDD-LTE B1/B3/B5/B8/B20/B28 2. Data rate- Uplink=<62.5Kbps- Downlink=<26.15Kbps3. SMS- Text mode and PDU mode (depends on the NB card)General Specifications1. Power supply: 5V2. Logic level: 5V/3.3V (3.3V by default)3. Overall current (idle mode): ~18mA4. Single module current (VBAT=3.3V):- Idle mode: 5.6mA- Sleep mode: 0.4mA- PSM mode: 5uA- eDRX mode: 70uA (eDRX=655.36s)5. Dimension: 30.5mm x 65.0mmPackage Contents1. SIM7020E NB-IoT HAT x12. Antenna x13. USB type A plug to micro plug cable x14. RPi screws pack (2pcs) x1Note: The Raspberry Pi is NOT included.

Read more less

L76X Multi-GNSS HAT for Raspberry Pi, Supports GPS, BDS, QZSSOverview1. This is a Raspberry Pi GNSS HAT which supports Multi-GNSS systems: GPS, BDS, and QZSS, with advantages such as fast positioning, high accuracy, low power consumption, and so on.2. It is an easy way to enable global positioning function for your Raspberry Pi.Features1. Support Multi-GNSS systems: GPS, BDS, and QZSS2. EASY, self track prediction technology, help quick positioning2. AlwaysLocate, intelligent controller of periodic mode for power saving3. Support DGPS, SBAS (WAAS/EGNOS/MSAS/GAGAN)4. UART communication baudrate: 4800~115200bps (9600bps by default)5. Onboard battery holder, supports ML1220 rechargeable battery, for preserving ephemeris information and hot starts6. 4x LEDs for indicating the module working status7. Come with development resources and manual (examples for Raspberry Pi/Arduino/STM32)GNSS Specifications1. Band: GPS L1(1575.42Mhz), BD2 B1 (1561.098MHz)- Channels: 33 tracking ch, 99 acquisition ch, 210 PRN ch- C/A code- SBA: WAAS, EGNOS, MSAS, GAGAN2. Horizontal position accuracy:- Autonomous: <2.5mCEP3. Time-To-First-Fix @-130dBm (EASY? enabled):- Cold starts: <15s- Warm starts: <5s- Hot starts: <1s4. Sensitivity:- Acquisition: -148dBm- Tracking: -163dBm- Re-acquisition: -160dBm5. Dynamic performance:- Altitude (max): 18000m- Velocity (max): 515m/s- Acceleration (max): 4GGeneral Specifications1. Communication interface: UART2. Baudrate: 4800~115200bps (9600bps by default)3. Update rate: 1Hz (default), 10Hz (max)4. Protocols: NMEA 0183, PMTK5. Power supply voltage: 5V / 3.3V6. Operating current: 13mA7. Operating temperature: -40 degree C ~ 85 degree C8. Dimensions: 65mm x 30.5mmApplications1. Vehicle tracking2. Asset tracking3. Security system4. Industrial PDA5. GIS applicationWhat is on Board1. L76B module2. CP2102: USB TO UART converter3. CAT24C32: EEPROM4. RT9193-33: Power manager5. Backup mode wakeup button6. Standby switch7. Indicators:- RXD/TXD: UART RX/TX indicator- PPS: GPS status indicator- PWR: Power indicator8. Raspberry Pi GPIO connector: For connecting with Raspberry Pi9. USB TO UART port10. GNSS antenna connector11. Battery holder: Support ML1220 rechargeable battery, for preserving ephemeris information and hot starts12. UART selection jumpers- A: control the L76B through USB TO UART- B: control the L76B through Raspberry Pi- C: access Raspberry Pi through USB TO UARTPackage Contents1. L76X GPS HAT x12. GPS External Antenna (B) x13. USB type A plug to micro plug cable x14. RPi screws pack (2pcs) x15. 2x20PIN pinheader x1

Read more less

4G/3G/GNSS HAT for Raspberry Pi, Based on SIM7600A-HApplicable Region1. SIM7600A-H is mainly applicable in North America (US, CA, MX), SIM7600E-H is mainly applicable in Southeast Asia, West Asia, Europe, Africa, SIM7600CE-T is mainly applicable in China.2. Please check the supported bands according to your local service provider, select the proper one when placing order.Overview1. The SIM7600A-H 4G HAT is a 4G communication and GNSS positioning module, which supports LTE CAT4 up to 150Mbps for downlink data transfer. it is pretty low power consumption.2. You can connect this 4G module with computer to surf the Internet, or attach it onto Raspberry Pi to enable functions like 4G high speed connection, wireless communication, making telephone call, sending SMS, global positioning, etc.Features1. Raspberry Pi connectivity, compatible with Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+2. Support dial-up, telephone call, SMS, MMS, mail, TCP, UDP, DTMF, HTTP, FTP, etc.3. Support GPS, BeiDou, Glonass, LBS base station positioning4. Onboard USB interface, to test AT Commands, get GPS positioning data, and so on5. Onboard CP2102 USB to UART converter, for serial debugging6. Breakout UART control pins, to connect with host boards like Arduino/STM327. SIM card slot, supports 1.8V/3V SIM card8. Onboard audio jack and audio decoder for making telephone call9. 2x LED indicators, easy to monitor the working status10. Onboard voltage translator, operating voltage can be configured to 3.3V or 5V via jumper11. Baudrate: 300bps ~ 4Mbps (default: 115200bps)12. Autobauding baudrate: 9600bps ~ 115200bps13. Control via AT commands (3GPP TS 27.007, 27.005, and V.25TER command set)14. Support SIM application toolkit: SAT Class 3, USAT15. Come with development resources and manual (examples for Raspberry Pi/Arduino/STM32)Communications Specifications1. Band: - LTE-- SIM7600A-H: --- LTE-FDD B2/B4/B12-- SIM7600E-H: --- LTE-FDD B1/B3/B5/B7/B8/B20--- LTE-TDD B38/B40/B41-- SIM7600CE-T: --- LTE-TDD B38/B39/B40/B41--- LTE-FDD B1/B3/B8- WCDMA / TD-SCDMA / CDMA 2000-- SIM7600A-H: --- UMTS/HSPA+ B2/B5-- SIM7600E-H: --- UMTS/HSPA+ B1/B5/B8-- SIM7600CE-T:--- UMTS/HSDPA/HSPA+ B1/B8--- TD-SCDMA B34/B39 --- CDMA 1X/EVDO BC0- GSM/GPRS/EDGE 900/1800 MHz2. Generation: 4G, 3G, 2.5G, 2G3. Emitting power: 0.25W, 0.5W@EGSM900, 0.4W@DCS1800, 2W@GSM900, 1W@DCS18004. Data Speed- LTE CAT 4-- Uplink=<50 Mbps-- Downlink=<150 Mbps- UMTS-- Uplink=<384Kbps-- Downlink=<384Kbps- EDGE-- Uplink=<236.8kbps-- Downlink=<236.8kbps- GPRS-- Uplink=<85.6kbps-- Downlink=<85.6kbps- HSPA+-- Uplink=<5.76Mbps-- Downlink=<42MbpsGNSS Specifications1. Receiver type- 16-channel- C/A code2. Sensitivity- Tracking: -159 dBm (GPS) / -158 dBm (GLONASS) / TBD (BD)- Cold starts: -148 dBm3. Time-To-First-Fix (open air)- Cold starts: <35s- Hot starts: <1s4. Accuracy- Position: <2.5m CEPSMS and Audio Specifications1. SMS- Support types: MT, MO, CB, Text, PDU- Storage: USIM card and ME (default)2. Audio feature- Support echo cancellation- Support noise reductionOther Specifications1. Power supply: 5V2. Operating voltage: 5V/3.3V (configured via jumper)3. Operating temperature: -30 degree C ~ 80 degree C4. Storage temperature: -45 degree C ~ 90 degree C5. Dimension: 56.21mm x 65.15mmWhat is on Board1. SIM7600A-H2. CP2102 USB to UART converter3. NAU8810 audio decoder4. TXS0108EPWR voltage translator: translates 3.3V/5V into 1.8V5. MP2128DT power chip6. MP1482 power chip7. Raspberry Pi GPIO header: for connecting with Raspberry Pi8. SIM7600 control interface: for connecting with host boards like Arduino/STM329. SIM card slot: supports 1.8V/3V SIM card10. 3.5mm earphone/mic jack11. USB interface: for testing AT Commands, getting GPS positioning data, etc.12. USB to UART interface: for serial debugging, or login to Raspberry Pi13. MAIN antenna connector14. AUX antenna connector15. GNSS antenna connector16. Power switch17. Network status indicator18. Power indicator19. Operating voltage selection jumper: - VCCIO - 3.3V: set operating voltage as 3.3V- VCCIO - 5V: set operating voltage as 5V20. UART selection jumper: - A: access Raspberry Pi via USB to UART- B: control the SIM7600 by Raspberry Pi- C: control the SIM7600 via USB to UARTPackage Contents1. SIM7600A-H 4G HAT x12. LTE Antenna x13. GPS External Antenna (B) x14. USB type A plug to micro plug cable x25. RPi screws pack (2pcs) x1

Read more less

Overview1. The SIM7600A-H 4G HAT is a 4G communication and GNSS positioning module, which supports LTE CAT4 up to 150Mbps for downlink data transfer. it is pretty low power consumption. 2. You can connect this 4G module with computer to surf the Internet, or attach it onto Raspberry Pi to enable functions like 4G high speed connection, wireless communication, making telephone call, sending SMS, global positioning, etc.Applicable Region1. SIM7600A-H is mainly applicable in North America (US, CA, MX), SIM7600E-H is mainly applicable in Southeast Asia, West Asia, Europe, Africa, SIM7600CE-T is mainly applicable in China. 2. Please check the supported bands according to your local service provider, select the proper one when placing order.Features1. Raspberry Pi connectivity, compatible with Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+ 2. Support dial-up, telephone call, SMS, MMS, mail, TCP, UDP, DTMF, HTTP, FTP, etc. 3. Support GPS, BeiDou, Glonass, LBS base station positioning 4. Onboard USB interface, to test AT Commands, get GPS positioning data, and so on 5. Onboard CP2102 USB to UART converter, for serial debugging 6. Breakout UART control pins, to connect with host boards like Arduino/STM32 7. SIM card slot, supports 1.8V/3V SIM card 8. Onboard audio jack and audio decoder for making telephone call 9. 2x LED indicators, easy to monitor the working status 10. Onboard voltage translator, operating voltage can be configured to 3.3V or 5V via jumper 11. Baudrate: 300bps-4Mbps (default: 115200bps) 12. Autobauding baudrate: 9600bps-115200bps 13. Control via AT commands (3GPP TS 27.007, 27.005, and V.25TER command set) 14. Support SIM application toolkit: SAT Class 3, USAT 15. Come with development resources and manual (examples for Raspberry Pi/Arduino/STM32)Communications Specifications1. Band: A. LTE: - SIM7600A-H: LTE-FDD B2/B4/B12 - SIM7600E-H: LTE-FDD B1/B3/B5/B7/B8/B20, LTE-TDD B38/B40/B41 - SIM7600CE-T: LTE-TDD B38/B39/B40/B41, LTE-FDD B1/B3/B8 B. WCDMA / TD-SCDMA/ CDMA 2000 - SIM7600A-H: UMTS/HSPA+ B2/B5 - SIM7600E-H: UMTS/HSPA+ B1/B5/B8 - SIM7600CE-T: UMTS/HSDPA/HSPA+ B1/B8, TD-SCDMA B34/B39, CDMA 1X/EVDO BC0 C. GSM/GPRS/EDGE 900/1800 MHz 2. Generation: 4G, 3G, 2.5G, 2G 3. Emitting power: 0.25W, 0.5W/EGSM900, 0.4W/DCS1800, 2W/GSM900, 1W/DCS1800 4. Data Speed - LTE CAT 4: Uplink=<50 Mbps, Downlink=<150 Mbps - UMTS: Uplink=<384Kbps, Downlink=<384Kbps - EDGE: Uplink=<236.8kbps, Downlink=<236.8kbps - GPRS: Uplink=<85.6kbps, Downlink=<85.6kbps - HSPA+: Uplink=<5.76Mbps, Downlink=<42MbpsGNSS Specifications1. Receiver type - 16-channel - C/A code 2. Sensitivity - Tracking: -159 dBm (GPS) / -158 dBm (GLONASS) / TBD (BD) - Cold starts: -148 dBm 3. Time-To-First-Fix (open air) - Cold starts: <35s - Hot starts: <1s 4. Accuracy - Position: <2.5m CEPSMS and Audio Specifications1. SMS - Support types: MT, MO, CB, Text, PDU - Storage: USIM card and ME (default) 2. Audio feature - Support echo cancellation - Support noise reductionOther Specifications1. Power supply: 5V 2. Operating voltage: 5V/3.3V (configured via jumper) 3. Operating temperature: -30 degree C ~ 80 degree C 4. Storage temperature: -45 degree C - 90 degree C 5. Dimension: 56.21mm x 65.15mmWhat is on Board1. SIM7600CE-T 2. CP2102 USB to UART converter 3. NAU8810 audio decoder 4. TXS0108EPWR voltage translator: Translates 3.3V/5V into 1.8V 5. MP2128DT power chip 6. MP1482 power chip 7. Raspberry Pi GPIO header: For connecting with Raspberry Pi 8. SIM7600 control interface: For connecting with host boards like Arduino/STM32 9. SIM card slot: Supports 1.8V/3V SIM card 10. TF card slot: Allows file/SMS/...storage 11. 3.5mm earphone/mic jack 12. USB interface: For testing AT Commands, getting GPS positioning data, etc. 13. USB to UART interface: For serial debugging, or login to Raspberry Pi 14. MAIN antenna connector 15. AUX antenna connector 16. GNSS antenna connector 17. Power switch 18. Network status indicator 19. Power indicator 20. Operating voltage selection jumper: - VCCIO-3.3V: set operating voltage as 3.3V - VCCIO-5V: set operating voltage as 5V 21. UART selection jumper: - A: Access Raspberry Pi via USB to UART - B: Control the SIM7600 by Raspberry Pi - C: Control the SIM7600 via USB to UARTPackage List1. SIM7600CE 4G HAT x1 2. LTE Antenna x1 3. GPS External Antenna (B) x1 4. USB type A plug to micro plug cable x2 5. RPi screws pack (2pcs) x1

Read more less

4G/3G/GNSS HAT for Raspberry Pi, Based on SIM7600E-HApplicable Region1. SIM7600A-H is mainly applicable in North America (US, CA, MX), SIM7600E-H is mainly applicable in Southeast Asia, West Asia, Europe, Africa, SIM7600CE-T is mainly applicable in China.2. Please check the supported bands according to your local service provider, select the proper one when placing order.Overview1. The SIM7600A-H 4G HAT is a 4G communication and GNSS positioning module, which supports LTE CAT4 up to 150Mbps for downlink data transfer. it is pretty low power consumption.2. You can connect this 4G module with computer to surf the Internet, or attach it onto Raspberry Pi to enable functions like 4G high speed connection, wireless communication, making telephone call, sending SMS, global positioning, etc.Features1. Raspberry Pi connectivity, compatible with Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+2. Support dial-up, telephone call, SMS, MMS, mail, TCP, UDP, DTMF, HTTP, FTP, etc.3. Support GPS, BeiDou, Glonass, LBS base station positioning4. Onboard USB interface, to test AT Commands, get GPS positioning data, and so on5. Onboard CP2102 USB to UART converter, for serial debugging6. Breakout UART control pins, to connect with host boards like Arduino/STM327. SIM card slot, supports 1.8V/3V SIM card8. Onboard audio jack and audio decoder for making telephone call9. 2x LED indicators, easy to monitor the working status10. Onboard voltage translator, operating voltage can be configured to 3.3V or 5V via jumper11. Baudrate: 300bps ~ 4Mbps (default: 115200bps)12. Autobauding baudrate: 9600bps ~ 115200bps13. Control via AT commands (3GPP TS 27.007, 27.005, and V.25TER command set)14. Support SIM application toolkit: SAT Class 3, USAT15. Come with development resources and manual (examples for Raspberry Pi/Arduino/STM32)Communications Specifications1. Band: - LTE-- SIM7600A-H: --- LTE-FDD B2/B4/B12-- SIM7600E-H: --- LTE-FDD B1/B3/B5/B7/B8/B20--- LTE-TDD B38/B40/B41-- SIM7600CE-T: --- LTE-TDD B38/B39/B40/B41--- LTE-FDD B1/B3/B8- WCDMA / TD-SCDMA / CDMA 2000-- SIM7600A-H: --- UMTS/HSPA+ B2/B5-- SIM7600E-H: --- UMTS/HSPA+ B1/B5/B8-- SIM7600CE-T:--- UMTS/HSDPA/HSPA+ B1/B8--- TD-SCDMA B34/B39 --- CDMA 1X/EVDO BC0- GSM/GPRS/EDGE 900/1800 MHz2. Generation: 4G, 3G, 2.5G, 2G3. Emitting power: 0.25W, 0.5W@EGSM900, 0.4W@DCS1800, 2W@GSM900, 1W@DCS18004. Data Speed- LTE CAT 4-- Uplink=<50 Mbps-- Downlink=<150 Mbps- UMTS-- Uplink=<384Kbps-- Downlink=<384Kbps- EDGE-- Uplink=<236.8kbps-- Downlink=<236.8kbps- GPRS-- Uplink=<85.6kbps-- Downlink=<85.6kbps- HSPA+-- Uplink=<5.76Mbps-- Downlink=<42MbpsGNSS Specifications1. Receiver type- 16-channel- C/A code2. Sensitivity- Tracking: -159 dBm (GPS) / -158 dBm (GLONASS) / TBD (BD)- Cold starts: -148 dBm3. Time-To-First-Fix (open air)- Cold starts: <35s- Hot starts: <1s4. Accuracy- Position: <2.5m CEPSMS and Audio Specifications1. SMS- Support types: MT, MO, CB, Text, PDU- Storage: USIM card and ME (default)2. Audio feature- Support echo cancellation- Support noise reductionOther Specifications1. Power supply: 5V2. Operating voltage: 5V/3.3V (configured via jumper)3. Operating temperature: -30 degree C ~ 80 degree C4. Storage temperature: -45 degree C ~ 90 degree C5. Dimension: 56.21mm x 65.15mmWhat is on Board1. SIM7600E-H2. CP2102 USB to UART converter3. NAU8810 audio decoder4. TXS0108EPWR voltage translator: translates 3.3V/5V into 1.8V5. MP2128DT power chip6. MP1482 power chip7. Raspberry Pi GPIO header: for connecting with Raspberry Pi8. SIM7600 control interface: for connecting with host boards like Arduino/STM329. SIM card slot: supports 1.8V/3V SIM card10. TF card slot: allows file/SMS/... storage11. 3.5mm earphone/mic jack12. USB interface: for testing AT Commands, getting GPS positioning data, etc.13. USB to UART interface: for serial debugging, or login to Raspberry Pi14. MAIN antenna connector15. AUX antenna connector16. GNSS antenna connector17. Power switch18. Network status indicator19. Power indicator20. Operating voltage selection jumper: - VCCIO - 3.3V: set operating voltage as 3.3V- VCCIO - 5V: set operating voltage as 5V21. UART selection jumper: - A: Access Raspberry Pi via USB to UART- B: Control the SIM7600 by Raspberry Pi- C: Control the SIM7600 via USB to UARTPackage Contents1. SIM7600E-H 4G HAT x12. LTE Antenna x13. GPS External Antenna (B) x14. USB type A plug to micro plug cable x25. RPi screws pack (2pcs) x1

Read more less

1.5 inch RGB OLED display module, 128x128 pixels, 16-bit high color, SPI interfaceOverviewThis is a general RGB OLED display Module, 1.5inch diagonal, 128x128 pixels, 16-bit high color (65K colors), with embedded controller, communicating via SPI interface.Features1. 128x128 high resolution, 65K colors, clearly displays colorful images2. Support 4-wire SPI OR 3-wire SPI interface, configured via onboard resistor3. Come with development resources and manual (examples for Raspberry Pi/Arduino/STM32)Specifications1. Driver: SSD13512. Interface: 4-wire SPI, 3-wire SPI3. Display color: RGB, 65K colors4. Resolution: 128x1285. Viewing angle: >160 degree6. Operating voltage: 3.3V / 5V7. Dimension: 44.5 x 37 (mm)Package Contents1. 1.5 inch RGB OLED Module x12. PH2.0 7Pin x1

Read more less

1.5inch OLED display Module, 128x128 pixels, 16 gray scale, SPI/I2C interfaceOverviewThis is a general OLED display Module, 1.5inch diagonal, 128x128 pixels, 16 gray scale, with embedded controller, communicating via SPI or I2C interface.Features1. 128x128 high resolution2. 16 gray scale, better display effect3. Support SPI or I2C interface, configured via onboard resistor4. Come with development resources and manual (examples for Raspberry Pi/Arduino/STM32)Specifications1. Driver: SSD13272. Interface: SPI / I2C3. Display color: White4. Gray scale: 165. Resolution: 128x128 (most other competitive products are typically 128x64)6. Viewing angle: >160 degree7. Operating voltage: 3.3V / 5V8. Dimension: 44.5 x 37 (mm)Package Contents1. 1.5 inch OLED Module x12. PH2.0 7Pin x1

Read more less

1. Driver chip: SSD13312. Interface: SPI3. Resolution: 96×644. Display size: 0.95inch5. Colors: 65K colorful6. Visible angle: >160°7. Operating temperature: -20~70 degree C8. Storage temperature: -30~80 degree C9. Operating voltage: 3.3V / 5V

Read more less

1. Driver chip: SH11062. Interface: 3-wire SPI, 4-wire SPI, I2C3. Resolution: 128*644. Display size: 1.3 inch5. Colors: Blue6. Visible angle: >160 degree7. Operating temperature: -30~70 degree C8. Storage temperature: -30~80 degree C9. Dimension: 40.50mm*37.50mm

Read more less

1. Driver chip: SH11062. Interface: 3-wire SPI, 4-wire SPI, I2C3. Resolution: 128*644. Display size: 1.3 inch5. Colors: Blue6. Visible angle: >160 degree7. Operating temperature: -30~70 degree C8. Storage temperature: -30~80 degree C9. Dimension: 40.50mm*37.50mm

Read more less

OverviewThis is a general OLED display Module, 0.91inch diagonal, 128x32 pixels, with embedded controller, communicating via I2C interface.Features1. 0.91inch small form factor2. 128x32 high resolution3. I2C interface, requires only two signal pins4. Comes with development resources and manual (examples for Raspberry Pi/Arduino/STM32)Specifications1. Driver: SSD13062. Interface: I2C3. Display color: White4. Resolution: 128x325. Viewing angle: >160 degree6. Operating voltage: 3.3V / 5V7. Dimension: 36 x 12.5 (mm)Package Contents1. 0.91inch OLED Module x13. PH2.0 4Pin x1

Read more less

1. Driver chip: SSD13062. Interface: 3-wire SPI, 4-wire SPI, I2C3. Resolution: 128*644. Display size: 0.96 inch5. Colors: 1/4 yellow section, 3/4 blue section6. Visible angle: >160 degree7. Operating temperature: -30~70 degree C8. Storage temperature: -30~80 degree C9. Operating voltage: 3.3V / 5V

Read more less

1. Driver chip: SSD13062. Interface: 3-wire SPI, 4-wire SPI, I2C3. Resolution: 128*644. Display size: 0.96 inch5. Colors: 1/4 yellow section, 3/4 blue section6. Visible angle: >160 degree7. Operating temperature: -30~70 degree C8. Storage temperature: -30~80 degree C9. Operating voltage: 3.3V / 5V

Read more less

Overview1. This is an E-Ink display module, 4.2inch, 400x300 resolution, with embedded controller, communicating via SPI interface.2. Due to the advantages like ultra low power consumption, wide viewing angle, clear display without electricity, it is an ideal choice for applications such as shelf label, industrial instrument, and so on.Features1. No backlight, keeps displaying last content for a long time even when power down2. Ultra low power consumption, basically power is only required for refreshing3. SPI interface, for connecting with controller boards like Raspberry Pi/Arduino/Nucleo, etc.4. Onboard voltage translator, compatible with 3.3V/5V MCUs5. Comes with development resources and manual (examples for Raspberry Pi/Arduino/STM32)Specifications1. Operating voltage: 3.3V~5V2. Interface: 3-wire SPI, 4-wire SPI3. Outline dimension: 103.0mm × 78.5mm4. Display size: 84.8mm × 63.6mm5. Dot pitch: 0.212 × 0.2126. Resolution: 400 × 3007. Display color: black, white8. Grey level: 29. Full refresh time: 4s10. Refresh power: 26.4mW(typ.)11. Standby power: <0.017mW12. Viewing angle: >170 degree13. Weight: 0.052 kgInterface1. SYMBOL: DESCRIPTION2. VCC: 3.3V~5V3. GND: Ground4. DIN: SPI MOSI pin5. CLK: SPI SCK pin6. CS: SPI chip selection, low active7. DC: Data/Command selection (high for data, low for command)8. RST: External reset, low active9. BUSY: Busy status output, low activePackage contents1. 4.2inch e-Paper Module x12. PH2.0 20cm 8Pin x1

Read more less

Overview1. This is an E-Ink raw display, 9.7inch, 1200x825 resolution, communicating via parallel port.2. Due to the advantages like ultra low power consumption, wide viewing angle, clear display without electricity, it is an ideal choice for applications such as shelf label, industrial instrument, and so on.Features1. No backlight, keeps displaying last content for a long time even when power down2. Low power consumption, basically power is only required for refreshing3. Comes with development resources and manual (driver board schematic, examples for Raspberry Pi/STM32)Specifications1. Operating voltage: 5V2. Interface: parallel port3. Outline dimension: 218.8mm x 156.425mm x 1.15mm4. Display size: 202.8mm x 139.425mm5. Dot pitch: 0.169 x 0.1696. Resolution: 1200 x 8257. Display color: black, white8. Gray scale: 2-16 (1-4 bit)9. Full refresh time: <1s10. Viewing angle: >170 degree11. Weight: 0.09 kg12. Note: This is a raw display, for easy testing and comparing, please consider the one with driver board: 9.7inch e-Paper HAT

Read more less

This is an E-Ink display HAT for Raspberry Pi, 2.7inch, 264x176 resolution, with embedded controller, communicating via SPI interface.Due to the advantages like ultra low power consumption, wide viewing angle, clear display without electricity, it is an ideal choice for applications such as shelf label, industrial instrument, and so on.Features1. No backlight, keeps displaying last content for a long time even when power down2. Ultra low power consumption, basically power is only required for refreshing3. Compatible with Raspberry Pi 2B/3B/3B+/Zero/Zero W4. Onboard 4x Keys5. SPI interface, for connecting with other controller boards like Raspberry/Arduino/Nucleo, etc.6. Onboard voltage translator, compatible with 3.3V/5V MCUs7. Comes with development resources and manual (examples for Raspberry Pi/Arduino/STM32)Specifications1. Operating voltage: 3.3V/5V2. Interface: 3-wire SPI, 4-wire SPI3. Outline dimension: 85mm x 56mm4. Display size: 57.288mm x 38.192mm5. Dot pitch: 0.217 x 0.2176. Resolution: 264 x 1767. Display color: Black, white8. Grey level: 29. Full refresh time: 6s10. Refresh power: 24mW(typ.)11. Standby power: <0.017mW12. Viewing angle: >170 degree13. Weight: 0.036 kgPackage Contents1. 2.7inch e-Paper HAT x12. RPi screws pack (2pcs) x23. PH2.0 20cm 8Pin x1

Read more less

Overview1. This is an E-Ink display HAT for Raspberry Pi, 7.5inch, 640x384 resolution, with embedded controller, communicating via SPI interface, supports red, black, and white three-color display.2. Due to the advantages like ultra low power consumption, wide viewing angle, clear display without electricity, it is an ideal choice for applications such as shelf label, industrial instrument, and so on.Features1. No backlight, keeps displaying last content for a long time even when power down2. Ultra low power consumption, basically power is only required for refreshing3. Compatible with Raspberry Pi 2B/3B/3B+/Zero/Zero W4. SPI interface, for connecting with other controller boards like Raspberry/Arduino/Nucleo, etc.5. Onboard voltage translator, compatible with 3.3V/5V MCUs6. Comes with development resources and manual (examples for Raspberry Pi/Arduino/STM32)Specifications1. Operating voltage: 3.3V~5V2. Interface: SPI3. Outline dimension: 170.2mm x 111.2mm4. Display size: 163.2mm x 97.92mm5. Dot pitch: 0.255 x 0.2556. Resolution: 640 x 3847. Display color: red, black, white8. Grey level: 29. Full refresh time: 16s10. Refresh power: 38mW(typ.)11. Standby power: <0.017mW12. Viewing angle: >170 degree13. Weight: 0.065 kgPackage Contents1. 7.5 inch e-Paper (B) x12. e-Paper Driver HAT x13. RPi screws pack (2pcs) x14. PH2.0 20cm 8Pin x1

Read more less

OverviewThis is a 2-DOF pan-tilt kit designed for Raspberry Pi. With onboard PCA9685 PWM chip and TSL2581 ambient light sensor, it allows the Pi to control camera movement and sense light intensity through I2C interface.Features1. Raspberry Pi connectivity, compatible with Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+2. I2C interface, only 2 pins are required for moving and light intensity sensing3. Onboard PCA9685 chip, provides 12-bit resolution PWM signal for moving control4. Onboard TSL2581FN light-to-digital converter, with embedded ADC, provides a value that approximates the human eye response to assist the module5. Onboard voltage level translator, compatible with 3.3V/5V operating voltage6. Specific acrylic board to fix the Raspberry Pi camera, make it easy to install7. Comes with development resources and manual (demo code, assembly guide)Specifications1. PWM driver: PCA96852. PWM resolution: 12-bit3. Ambient light sensor: TSL2581FN4. Ambient light resolution: 16-bit5. Communication interface: I2C6. Operating voltage: 3.3V/5V7. Dimension: 56.6mm x 65mmHow to AssembleA little assembly work is required to use the Pan-Tilt HAT, yet its pretty easy to do, heres the assembly guide.Package Contents1. Pan-Tilt HAT x12. 2-DOF pan-tilt kit x13. SG90 servo x14. MG90S servo x15. Acrylic board x16. M2 screws pack x17. RPi screws pack (2pcs) x1

Read more less

Overview1. The OV9655 Camera Board is a simple digital camera based on OV9655.2. The OV9655 Camera Board makes it possible to take photos and/or record video with your development board.FeaturesOV9655, camera, control interface

Read more less

Camera Module Based on OV5640 Image Sensor, 5 Megapixel (2592x1944), Auto Focusing with Onboard Flash LEDFeatures1. Pixels: 5 megapixel2. Resolution: 2592x19443. Auto focusing by detecting the object distance4. Onboard flash LED, allowed to take pictures in the dark5. Sensor: OV5640- 1.4um x 1.4um pixel with OmniBSI technology, high sensitivity, low crosstalk, low noise- Automatic image control functions: AEC, AWB, ABF, ABLC, etc.- Image quality controls: color saturation, hue, gamma, sharpness, lens correction, etc.- Supports image scaling, panning, windowing, etc.6. Lens:- CCD size: 1/4inch- Aperture (F): 2.8- Focal Length: 3.37mm (adjustable)- Diagonal: 67.4 degree7. Output Formats:- YUV(422/420)/YCbCr422- RGB565/555/444- CCIR656- RAW RGB- Compressed Data8. Operating Voltage: 3.3V9. Control Interface: SCCB (I2C compatible)10. Data Interface: DVP 8-bit11. Dimension: 35.70mm x 23.90mm

Read more less

Features1.Pixels: 5 megapixel2.Resolution: 2592x19443.Sensor: OV5640 3.1 1.4um x 1.4um pixel with OmniBSI technology, high sensitivity, low crosstalk, low noise 3.2 Automatic image control functions: AEC, AWB, ABF, ABLC, etc. 3.3 Image quality controls: color saturation, hue, gamma, sharpness, lens correction, etc. 3.4 Supports image scaling, panning, windowing, etc.4.Lens: 4.1 CCD size: 1/4inch 4.2 Aperture (F): 2.8 4.3 Focal Length: 2.8mm 4.4 Diagonal: 63 degree5.Output Formats: 5.1 YUV(422/420)/YCbCr422 5.2 RGB565/555/444 5.3 CCIR656 5.4 RAW RGB 5.5 Compressed Data6.Operating Voltage: 3.3V7.Control Interface: SCCB (I2C compatible)8.Data Interface: DVP 8-bit9.Dimension: 35.70mm × 23.90mm

Read more less

Features1. Pixels: 5 megapixel2. Resolution: 2592x19443. Sensor: OV5640- 1.4um x 1.4um pixel with OmniBSI technology, high sensitivity, low crosstalk, low noise- Automatic image control functions: AEC, AWB, ABF, ABLC, etc.- Image quality controls: color saturation, hue, gamma, sharpness, lens correction, etc.- Supports image scaling, panning, windowing, etc.4. Lens:- CCD size: 1/4inch- Aperture (F): 2.5- Focal Length: 2.0mm- Diagonal: 170 degree (fisheye)5. Output Formats:- YUV(422/420)/YCbCr422- RGB565/555/444- CCIR656- RAW RGB- Compressed Data6. Operating Voltage: 3.3V7. Control Interface: SCCB (I2C compatible)8. Data Interface: DVP 8-bit9. Dimension: 35.70mm x 23.90mm

Read more less

10 DOF IMU Sensor (C), Inertial Measurement Unit, Lower Power ConsumptionOverview10 DOF IMU Sensor (C) is good at motion monitor, as well as detecting/measuring the position, height, and temperature. It would be helpful for making your own copter or balancing robot, provides great man-machine interaction.Features1. MPU9250: 3-axis gyroscope, 3-axis accelerometer, and 3-axis compass/magnetometer- Internal Digital Motion Processing™ (DMP™) engine, offloads complicate fusion calculation, sensor synchronization, gesture recognition, etc.- Comparing with MPU6050, it is lower power consumption, and more suitable for wearable devices2. BMP280: barometric pressure sensor- Embedded temperature sensor for temperature compensation- Comparing with BMP180, it is lower power consumption, and higher performance3. You can get the 10 DOF data through I2C interface

Read more less

Overview10 DOF IMU Sensor (D) features the low power ICM20948 onboard, it is good at motion monitoring, as well as detecting/measuring the position, height, and temperature.This tiny module would be helpful for making your own copter or balancing robot, provides great man-machine interaction.Features1. ICM20948: Low power 3-axis gyroscope, 3-axis accelerometer, and 3-axis compass/magnetometer- Internal Digital Motion Processing™ (DMP™) engine, offloads complicate fusion calculation, sensor synchronization, gesture recognition, etc.- Comparing with MPU9250, it is higher precision, lower power consumption, and more suitable for wearable devices2. BMP280: barometric pressure sensor- Embedded temperature sensor for temperature compensation- Comparing with BMP180, it is lower power consumption, and higher performance3. You can get the 10 DOF data through I2C interface

Read more less

UART Fingerprint Reader, onboard processor STM32F205, commercial fingerprinting algorithm, optical sensorOverviewUART Fingerprint Reader is a fingerprinting module designed for secondary development, high-speed for identification, high stability. It is an intelligent module that provides functionalities like fingerprint recording, image processing, feature extraction, template generation, template storage, fingerprint matching and searching, etc.Features1. Onboard high-speed processor STM32F2052. Commercial fingerprinting algorithm, faster identification3. High-accuracy optical sensor, standard 16-pin interface, allows users to choose optical/semiconductor sensors4. Divided structure: fingerprint sensor + processing circuit + algorithm platform5. Easy for developing, controlled via UART, supports any MCU with UART6. Open protocol, it is available to freely input/output fingerprint images, fingerprint feature file and other fingerprinting actionsPackage Contents1. UART Fingerprint Reader × 12. 6-pin custom connector jumper wire × 1

Read more less

Capacitive Fingerprint Reader, onboard processor STM32F105, commercial fingerprinting algorithm, semiconductor sensorOverview1. The Capacitive Fingerprint Reader is a standard fingerprinting module designed for secondary development, allows fast and stable fingerprint verification.2. Based on a high-speed digital processor STM32F105R8, combined with high-security commercial fingerprinting algorithm, and advanced semiconductor sensor, the Capacitive Fingerprint Reader becomes a simple but smart integration module, provides functionalities like fingerprint enrolling, image processing, feature finding, template generating and storing, fingerprint matching and searching, etc.Features1. Easy to use by some simple commands, you dont have to know any fingerprint technology, or the module inter structure/calculation2. Commercial fingerprinting algorithm, stable performance, fast verification3. Sensitive detection, just touch the collecting window lightly, without pressing4. Allows to freely input/output fingerprint images, fingerprint feature file and other fingerprinting actions5. Dual communication, UART or USB6. Processor will enter sleep and wake up when detecting, achieves low power consumption7. Comes with rich related resources (software on PC, development SDK, tools, and examples for Raspberry/Arduino/STM32)Package Contents1. Capacitive Fingerprint Reader x12. PH2.0 wire 20cm 6Pin x1

Read more less

Overview1. Onboard audio power amplifier LM3862. Audio signal gain up to 2003. Adjustable accuracy4. Signal output indicatorSpecifications1. Mic sensitivity: 52dB2. Frequency range: 50Hz ~ 20KHz3. Power: 3.3V ~ 5.3V4. Mounting holes size: 2.0mmApplications1. Audio amplifier2. Ambient sound detection3. Sound level detection (unable to get exact dB value)How to UseIn the case of working with a MCU:1. VCC: 3.3V ~ 5.3V2. GND: Power supply ground3. AOUT: MCU.IO (analog output)4. DOUT: MCU.IO (digital output)Package Contents1. Sound Sensor x12. 4-pin custom connector jumper wire x1

Read more less

Overview1. Sensitive for benzene, alcohol, smoke2. Output voltage boosts along with the concentration of the measured gases increases3. Fast response and recovery4. Adjustable sensitivity5. Signal output indicatorSpecifications1. Power: 2.5V ~ 5.0V2. Dimension: 40.0mm * 21.0mm3. Mounting holes size: 2.0mmApplicationsAir quality monitorHow to UseIn the case of working with a MCU:1. VCC: 2.5V ~ 5.0V2. GND: Power supply ground3. AOUT: MCU.IO (analog output)4. DOUT: MCU.IO (digital output)Package Contents1. MQ-135 Gas Sensor x12. 4-pin custom connector jumper wire x1

Read more less

Overview1. Sensitive for LPG, natural gas, coal gas2. Output voltage boosts along with the concentration of the measured gases increases3. Fast response and recovery4. Adjustable sensitivity5. Signal output indicatorSpecifications1. Power: 2.5V ~ 5.0V2. Dimension: 40.0mm * 21.0mm3. Mounting holes size: 2.0mmApplicationsGas leakage detectorHow to UseIn the case of working with a MCU:1. VCC: 2.5V ~ 5.0V2. GND: Power supply ground3. AOUT: MCU.IO (analog output)4. DOUT: MCU.IO (digital output)Package Contents1. MQ-5 Gas Sensor x12. 4-pin custom connector jumper wire x1

Read more less

Overview1. Sensitive for LPG, propane, hydrogen2. Output voltage boosts along with the concentration of the measured gases increases3. Fast response and recovery4. Features boost circuit5. Adjustable sensitivity6. Signal output indicatorSpecifications1. Power: 2.5V ~ 5.0V2. Dimension: 40.0mm * 21.0mm3. Mounting holes size: 2.0mmApplicationsGas leakage detectorHow to UseIn the case of working with a MCU:1. VCC: 2.5V ~ 5.0V2. GND: Power supply ground3. AOUT: MCU.IO (analog output)4. DOUT: MCU.IO (digital output)Package Contents1. MQ-2 Gas Sensor x12. 4-pin custom connector jumper wire x1

Read more less

Overview1. Sharp GP2Y1010AU0F onboard, detecting fine particle larger than 0.8μm in diameter, even like the cigarette smoke2. Low power consumption, analog voltage output, the output level is linear with dust density3. Embedded voltage boost circuit to support wide range of power supplySpecifications1. Sensitivity : 0.5V/(100ug/m3)2. Measurement range : 500ug/m33. Power : 2.5V~5.5V4. Operating current : 20mA(max)5. Operating temperature : -10~65 degree C6. Storage temperature : -20~80 degree C7. Life time : 5 years8. Dimension : 63.2mmx41.3mmx21.1mm9. Mounting holes size : 2.0mm10. Air hole size : 9.0mmApplications1. Air purifier2. Air conditioner3. Air monitor4. PM2.5 DetectorHow to UseIn the case of working with a MCU:1. VCC: 2.5V ~ 5.0V2. GND: GND3. AOUT: MCU.IO (analog output)4. ILED: MCU.IO (module driving pin)Package Contents1. Dust Sensor × 12. XH2.54 4-pin wire × 1

Read more less

Overview1. Sensitive for carbon monoxide2. Output voltage boosts along with the concentration of the measured gases increases3. Fast response and recovery4. Adjustable sensitivity5. Signal output indicatorSpecifications1. Power: 2.5V ~ 5.0V2. Dimension: 40.0mm * 21.0mm3. Mounting holes size: 2.0mmApplicationsCarbon monoxide monitorHow to UseIn the case of working with a MCU:1. VCC: 2.5V ~ 5.0V2. GND: Power supply ground3. AOUT: MCU.IO (analog output)4. DOUT: MCU.IO (digital output)Package Contents1. MQ-7 Gas Sensor x12. 4-pin custom connector jumper wire x1

Read more less

Features1. 5inch IPS screen, 800x480 hardware resolution2. Compatible with Raspberry Pi 2B/3B/3B+/3A+/Zero/Zero W/Zero WH3. The LCD is directly driven by Raspberry Pi DPI interface, refresh rate up to 60Hz4. Supports Raspbian, Ubuntu, OSMC, etc.5. Backlight can be turned off to lower power consumption6. Compact size, suit for various projectsNote: This item can be used for displaying ONLY, if touch panel is required, please consider 5inch HDMI Capacitive Touch LCD OR 5inch HDMI Resistive Touch LCD.Package Contents1. 5inch 800×480 IPS LCD x12. RGB LCD HAT (B) x13. LCD stand (small size) x1

Read more less

Features1. 13.3inch IPS screen,1920x1080 hardware resolution2. Toughened glass capacitive touch panel, 6H hardness3. Support popular mini PCs such as Raspberry Pi, Jetson Nano, BB Black, as well as general desktop computers- When works with Raspberry Pi, supports Raspbian/Ubuntu/Kali/Retropie/WIN10 IOT, driver free- When work as a computer monitor, supports Windows 10/8.1/8/7, ten-points touch, and driver free4. Support popular game consoles like Microsoft XBOX360, Sony PS4, and Nintendo Switch5. Multi languages OSD menu, for power management, brightness/contrast adjustment, etc.6. 3.5mm audio jack, supports HDMI audio output7. Embedded ferrite Hi-Fi speaker8. Also supports VGA input (specific cable is required and should be purchased separately)10. 100x100mm spacing mounting holes (M4 screw hole) for general wall mount11. Comes with 60 degree tilt angle standNote: 1. Limited by the game console OS, the touch function is unavailable.2. Sound support means, it is possible for the game console to output sound signal via LCD embedded speaker, external speaker interface, or earphone jack.Package Contents1. 13.3inch HDMI LCD (H) (with case) V2 x12. Power adapter 12V x13. HDMI cable x14. USB type A plug to micro B plug cable x15. Quick start sheet x1

Read more less

OverviewThis is a color sensor module based on TCS34725, will output RGB data and light intensity through the I2C interface. Its advantages include high sensitivity, wide dynamic range, accurate measuring, etc.Features1. Onboard TCS34725FN, embedded ADC, high sensitivity, wide dynamic range2. I2C communication, uses a few pins3. Integrates IR blocking filter, minimizes the IR spectral component of the incoming light4. Outputs RGB data without white balance5. Outputs light intensity, feels the light like human eyes6. Supports light intensity interrupt output, programmable upper and lower thresholds7. Supports fill-light by onboard LED, adjustable brightness by PWM8. Onboard voltage level translator, compatible with 3.3V/5V operating voltage9. Comes with development resources and manual (examples for Raspberry Pi/Arduino/STM32)Specifications1. Sensor: TCS34725FN2. Communication interface: I2C3. Operating voltage: 3.3V/5V4. Dimension: 27mm × 20mm5. Resolution: 4-ch RGBC, 16-bit per ch6. Recommended measuring distance: 2mmApplications1. Sorting by color2. Ambient light sensing and calibration3. Products color identification and classificationPinouts1. VCC: 3.3V/5V power input2. GND: ground3. SDA: I2C data input4. SCL: I2C clock input5. INT: Interrupt output (open drain output)6. LED: Light emitting diodePackage Contents1. TCS34725 Color Sensor x12. PH2.0 6PIN wire 20cm x1

Read more less

Overview1. Reflective infrared Transceiver2. Features wide range voltage comparator LM3933. Adjustable sensitivity4. Signal output indicatorSpecifications1. Power: 3.0V ~ 5.3V2. Dimension: 25mm * 15.9mm3. Mounting holes size: 2.0mmApplications1. Robot path tracking2. Obstacle-avoiding car3. Pipeline counterHow to UseIn the case of working with a MCU:Pinouts1. VCC: 3.0V ~ 5.3V2. GND: Power supply ground3. AOUT: MCU.IO (analog output)4. DOUT : MCU.IO (digital output)Package Contents1. Infrared Reflective Sensor x12. 4-pin custom connector jumper wire x1

Read more less

VL53L1X Time-of-Flight long distance ranging sensor, accurate ranging up to 4m and fast ranging frequency up to 50HzOverview1. VL53L1X Distance Sensor is a Time-of-Flight (ToF) ranging module based on the VL53L1X from ST, with accurate ranging up to 4m and fast ranging frequency up to 50 Hz, it is controlled through I2C interface, and pretty low power consumption.2. The VL53L1X is a ToF sensor which embeds the ST’s third generation FlightSense patented technology. Compared with the second generation VL53L0X, the VL53L1X extends the ToF ranging distance up to 4m, and features fast ranging frequency up to 50 Hz.3. Unlike conventional ranging sensors, the VL53L1X integrates physical infrared filters and optics, uses ST’s latest generation ToF technology which allows absolute distance measurement whatever the target color and reflectance, achieves better anti-interference capability.Features1. I2C communication interface, control the module on/off via IO pins2. Onboard voltage translator, compatible with 3.3V/5V operating voltage3. Comes with development resources and manual (examples for Raspberry Pi/Arduino/STM32)Specifications1. Operating voltage: 3.3V/5V2. Dimension: 20mm × 24mm3. Mounting holes size: 2.0mm4. Ranging distance: 40 ~ 4000mm5. Ranging accuracy: +/-5%6. Ranging time (min): 20ms (short distance mode), 33ms (medium/long distance mode)7. Field of view: 27 degree8. Laser wavelength: 940nm9. Operating temperature: -20 ~ 80 degree CApplications1. Mobile robot (fast distance ranging, obstacle detecting, wall tracking)2. User detection to power on/off and lock/unlock devices like personal computers/laptops/tablets3. Drones (landing assistance, hovering, ceiling detection)4. Smart building and lighting (people detection, 1D gesture recognition)5. Camera (autofocus enhancement in low light, video focus tracking assistance)Pinouts1. VCC: 3.3V/5V power input2. GND: Ground3. SDA: I2C data pin4. SCL: I2C clock pin5. SHUT: shutdown control, connects to IO pin6. INT: interrupt output, connects to IO pinPackage Contents1. VL53L1X Distance Sensor x13. PH2.0 6PIN wire 20cm x1

Read more less

Overview1. This is a calibrated digital temperature and humidity module with onboard sensor DHT22 (AM2302), which features higher accuracy and wider measuring range than DHT11.2. It can be used for detecting ambient temperature and humidity, through the standard single-wire interface.Specifications1. Temperature- Resolution : 0.1degree C- Accuracy: +/-0.5 degree C- Measuring range: -40 degree C ~ 80 degree C2. Humidity- Resolution: 0.1%RH- Accuracy: +/-2%RH (25degree C)- Measuring range: 0%RH ~ 99.9%RH3. Operating voltage: 3.3V ~ 5.5 V4. Recommended storage condition- Temperature: 10 degree C ~40 degree C- Humidity: 60%RH or belowApplications1. Weather station2. Humidity controller3. Test & detection deviceHow to UseIn the case of working with a MCU:1. VCC: 3.3V ~ 5.5V2. GND: GND3. DOUT: MCU.IO

Read more less

Overview1. Fork-like design, make it easy to insert into the soil2. Output voltage boosts along with the soil moisture level increasesSpecifications1. Detection depth: 38mm2. Power: 2.0V ~ 5.0V3. Dimension: 20.0mm * 51.0mm4. Mounting holes size: 2.0mmApplications1. Auto watering system2. Flowerpot soil moisture detection3. Auto pouring systemHow to UseIn the case of working with a MCU:1. VCC: 3.3V ~ 5.5V2. GND: GND3. DOUT: MCU.IOPackage Contents1. Moisture Sensor x12. 3-pin custom connector jumper wire x1

Read more less

BMP388 High Precision Barometric Pressure Sensor, Altitude / Barometric Pressure / Temperature Measuring, I2C/SPI InterfaceOverview1. This is a 24-bit high precision barometric pressure sensor, which allows accurate altitude tracing, as well as barometric pressure / temperature measuring. It supports both I2C and SPI interfaces, also is compatible with 3.3V/5V voltage levels.2. Due to its ultra small form factor, low power consumption, low noise and high precision, the BMP388 Barometric Pressure Sensor is suited for applications such as drones, accurate altimeter, environment monitoring, and IoT projects, and so on.Features1. Supports I2C (default) / SPI interface2. Onboard voltage level translator, compatible with 3.3V/5V operating voltage3. Comes with development resources and manual (examples for Raspberry Pi/Arduino/STM32)Specifications1. Operating voltage: 3.3V/5V2. Communication interface: I2C/SPI3. Barometric pressure operation range: 300~1250hPa4. Barometric pressure absolute accuracy: +/-0.40hPa (@900~1100hPa, 25~40 degree C)5. Barometric pressure relative accuracy: +/-0.08hPa (@900~1100hPa, 25~40 degree C)6. Temperature coefficient offset: ±0.75Pa/K (@700~1100hPa, -20~65 degree C)7. Temperature absolute accuracy: +/-0.5 degree C (0~65 degree C）8. Possible resolution: 0.016Pa (high precision mode)9. Possible sampling rate: 200Hz10. Operating voltage: -40~85 degree C11. Dimension: 32mm × 20mm12. Mounting hole size: 2.0mmPinouts1. VCC: 3.3V/5V power supply2. GND: Ground3. SDA: I2C data4. SCL: I2C clock5. INT: Interrupt output, can be connected to I/OPackage Contents1. BMP388 Barometric Pressure Sensor x12. PH2.0 5PIN wire x1

Read more less