Electronics Modules

Specifications1. CM4 Socket: Available on all variants of Compute Module 4 2. Network: Gigabit Ethernet RJ45 connector, 100M Ethernet RJ45 connector 3. USB: USB 2.0 Type A x 2 4. Connector: Isolated RS485 x 4, power screw terminal x 1 5. Camera: MIPI CSI-2 port x 2 (15pin 1.0mm FPC connector) 6. Video: HD-MI interface x 1, support 4K 30fps output 7. RTC: Real Time Clock with Battery Socket and Ability to Wake Compute Module 4 8. Storage: MicroSD card slot for Compute Module 4 Lite (no eMMC) variant 9. Fan head: allow speed adjustment, 5V 10. Indicator: Power indicator x 1, CM4 status indicator x 1, User LED x 2, RS485 communication indicator x 8 11. Power input: 7-36V 12. Dimensions: 123 x 98 x 32mmPackage List1. CM4-ETH-RS485-BASE-B x 1 2. Metal case (top and bottom) x 1 3. Fan x 1 4. 12V 2A Power Supply x 1 5. Screwdriver x 1 6. Antenna connector rubber plug x 1 7. Screws pack x 1

Read more less

1. 172 x 320 resolution, 262K RGB colors, clear and colorful displaying effect 2. SPI interface, mini mizes required IO pins, supports controller boards like Raspberry Pi/Arduino/STM32 3. Come with development resources (examples for Raspberry Pi/Arduino/STM32) 4. Working voltage: 3.3V/5V 5. Resolution: 172 x 320 pixels 6. Communication interface: 4-wire SPI 7. Display size: 17.39 x 32.35mm 8. Display panel: IPS 9. Pixel pitch: 0.0337 x 0.1011mm 10. Driver: ST7789V3 11. Dimensions: 22.0 x 38.5mm

Read more less

Features1. Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson Nano 2. Onboard dual HR8825 motor controller IC with built-in microstepping indexer, drives two stepper motors, easy to use 3. 6 available microstepping modes, configured with the DIP switches: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step 4. Adjustable motor drive current via potentiometer, maximum 2.5A current output 5. Protection features: Overcurrent Protection (OCP), Thermal Shutdown (TSD), VM Undervoltage Lockout (UVLO) 6. Integrates 5V regulator, allows providing power to Raspberry Pi 7. Onboard multi connector options for stepper motors in different specifications 8. Comes with development resources and manual (examples in BCM2835, wiringPi, and python)Specifications1. Motor controller: HR8825 2. Motor drive voltage: 8.2V~28V 3. Motor drive current: 2.5A 4. Logic voltage: 3.3V 5. Mounting hole size: 3.0mm 6. Size: 65 x 56mmPackage List1. Stepper Motor HAT (B) x 1 2. RPi screws pack (2pcs) x 1 3. Aluminum heatsink x 1

Read more less

Specifications1. CM4 Socket: Available on all variants of Compute Module 4 2. Network: Gigabit Ethernet RJ45 connector, 100M Ethernet RJ45 connector 3. USB: USB 2.0 Type A x 2 4. Connector: Isolated RS485 x 4, power screw terminal x 1 5. Camera: MIPI CSI-2 port x 2 (15pin 1.0mm FPC connector) 6. Video: HD-MI interface x 1, support 4K 30fps output 7. RTC: Real Time Clock with Battery Socket and Ability to Wake Compute Module 4 8. Storage: MicroSD card slot for Compute Module 4 Lite (no eMMC) variant 9. Fan head: allow speed adjustment, 5V 10. Indicator: Power indicator x 1, CM4 status indicator x 1, User LED x 2, RS485 communication indicator x 8 11. Power input: 7-36V 12. Dimensions: 123 x 98 x 32mmPackage List1. CM4-ETH-RS485-BASE-B x 1 2. Metal case (top and bottom) x 1 3. Fan x 1 4. 12V 2A Power Supply x 1 5. Screwdriver x 1 6. Antenna connector rubber plug x 1 7. Screws pack x 1

Read more less

FeaturesThis is a RS485 device data acquisitor / IoT gateway designed for industrial environment. It combines multi functions in one, including serial server, Modbus gateway, MQTT gateway, RS485 to HTTPD Client, etc. With RS485, WIFI and Ethernet ports, the module can realize functions such as serial to WIFI, serial to Ethernet, Ethernet to WIFI and so on. Using screw terminals for power input, it supports 5~36V wide range power supply. Rail-mount V0 flame-retardant case design, small in size, easy to install. It is suitable for applications like data acquisition, IoT gateway, safety & security IoT, and intelligent instrument monitoring...SpecificationsOutline: 1. Communication interface: RS485, screw terminal 2. Power supply: 5 ~ 36V DC, screw terminal 3. Case: PC + ABS, V0 flame retardant grade 4. Dimensions: L x W x H: 109.66 x 28 x 64.71 mm Comunication: 1. Ethernet: 10 / 100M auto-negotiation RJ45 connector 2. WIFI: 802.11b/g/n compliant 3. Serial port: RS485 interface (Anti-surge, Lightningproof, Over-current protection) Wireless specification: 1. Frequency Band: 2.412 ~ 2.484 GHz 2. Wireless network: Station / AP / AP+Station Mode 3. Security mechanism: WPA-PSK / WPA2-PSK 4. Encryption type: TKIP / AES 5. Transmitting power: - 802.11b: +19dBm (11Mbps) - 802.11g: +18dBm (54Mbps) - 802.11n: +17dBm (HT20, MCS7); +17dBm (HT40, MCS7) 6. Receiving sensitivity: - 802.11b: -89dBm (11Mbps) - 802.11g: -81dBm (54Mbps) - 802.11n: -73dBm (HT20, MCS7); -71dBm (HT40, MCS7) Serial specification: 1. Baudrate: 300 ~ 460800 bps 2. Parity bit: None, odd, even, mark, space 3. Data bit: 5 ~ 9 bits 4. Flow control: N/A Software 1.Protocol: TCP / UDP / ARP / ICMP / DHCP / DNS / HTTP / MQTT 2. Configuration: Host, web browser, serial AT command 3. Communication method: TCP/IP direct communication, VCOM 4. Operating mode: Transparent transmission, serial command, HTTPD Client, Modbus TCP to Modbus RTU Environmental requirements 1. Working temperature: -40 ~ 85 degree C 2. Storage temperature: -45 ~ 125 degree C 3. Humidity range: 5% ~ 95% relative humidityPackage List1. RS485 TO WIFI/ETH x 1 2. Antenna x 1

Read more less

Features1. 2.8-inch IPS capacitive touch screen with a hardware resolution of 480 x 640. 2. Capacitive 5-point touch control. 3. Tempered glass capacitive touch panel, hardness up to 6H. 4. Drive LCD directly through Raspberry Pi DSI interface with a refresh rate of up to 60Hz. 5. Working with Raspberry Pi, supports Raspberry Pi OS system. 6. Support Pi 4B/3B+/3A+, CM3+/4 must be used with an adapter board. 7. Backlight brightness control by the software.Package List1. 2.8 inch DSI LCD x1 2. FPC 15PIN 1.0 pitch 50mm (opposite sides) x2

Read more less

1. Product name: USB video capture card 2. Input: HDMI, 4K (3840 x 2160 30Hz) 3. HDMI: 1.4B Compatible 4. Output: - USB2.0, 1080P (1920 x 1080 30Hz) - Support custom resolution - Supports YUV and JPEG modes - USB1.1 compatible, UVC1.0 protocol compatible 5. Audio: Synchronize audio and video 6. System support: Windows, Linux, macOS, Android 7. Software support: OBS, Potplayer, QuickTime, XSplit, etc.

Read more less

1. 3.5 inch IPS screen, hardware resolution is 640 ?? 480. 2. 5-point capacitive touch, tempered glass panel, hardness up to 6H. 3. When used with Raspberry Pi, supports Raspberry Pi OS / Ubuntu / Kali and Retropie. 4. When used with Tinker Board 2, it supports Android / Debian. 5. Ubuntu is supported when used with Jetson Nano. 6. When used as a computer monitor, supports Windows 11/10/8.1/8/7. 7. Onboard dual touch circuit, optional USB Type-C or I2C touch, more application scenarios. 8. With 3.5mm audio and speaker interface, support HDMI audio output.

Read more less

Features1. Onboard switch chip, 5x ports 10/100/1000M non-blocking switch architecture 2. Full-duplex 10/100/1000M support for each port (the half-duplex 100M connection is only supported on 10/100M mode) 3. Full/Half-duplex operations with IEEE 802.3x flow control and back pressure support 4. Allow forwarding 9216 bytes huge data packet on linear speed 5. Over-voltage protection, effectively preventing damages caused by other high voltage power supply 6. Industrial grade alloy case, solid and durable, with DIN rail mount support for easy installing 7. 5~36V wide voltage power supply, dual power interface (DC interface and terminal block) onboard overvoltage protection, reverse connection protection. 8. Support 25mm standard rail.Package List1. Gigabit-Switch-5P x 1 2. Power supply screw terminal x 1 3. 12V 1A power adapter x 1

Read more less

Features1. I2C bus, allows expanding 16 I/O ports by just using two wires 2. Support driving 16-ch common anode constant current LED, 256-step linear dimming, current controllable 3. Output interrupt (INT) signal when changing the state of an input port 4. I2C address configurable by shorting the A0/A1 jumpers 5. Provide two connector options: PH2.0 header and/or solder pads, allows multi I2C modules to be stacked 6. Onboard voltage translator, compatible with 3.3V/5V level 7. Come with development resources and manual (examples for Raspberry Pi / micro:bit / Arduino / STM32)Specifications1. Working voltage: 2.4-5.5V 2. Working temperature: -40-85 degree c 3. Low Standby Current: Less than 0.1uA 4. Control interface: I2C 5. Expansion I/O pins: 16 6. Size: 38x23mmPackage List1. AW9523B IO Expansion Board x 1 2. PH2.0 6PIN wire x 1

Read more less

FeaturesThe IMx290-83 IR-CUT Camera is a starlight camera for the Raspberry Pi board and module series. Using a IMX290 starlight sensor with 2 million pixels, onboard IR-CUT, it can freely switch the modes between daytime (RGB) and nighttime (monochrome) through the onboard button.Specifications1. Sensor: IMX290 2. CMOS size: 1/2.8 inch 3. Pixels: 2MP (1920 x 1080) 4. Aperture: F2 5. Focal length: 3.95mm 6. Camera type: Color 7. Field of vies: 98 degree 8. Distortion: Less than 33% 9. Shutter: Rolling Shutter 10. Focusing: Fixed focusPackage List1. IMX290-83 IR-CUT Camera x1 2. 15-pin FFC (opposite sides contact) x1

Read more less

1. Standard 40PIN GPIO extension header, supports direct attaching to Jetson Nano 2. Onboard CAN controller MCP2515 via SPI interface, matching with SIT65HVD230DR transceiver 3. Features RS485 function, controlled via UART, half-duplex communication, supports automatic TX/RX control without programming, onboard transceiver SP3485 4. Onboard TVS (Transient Voltage Suppressor), effectively suppress surge voltage and transient spike voltage in the circuit for RS485 transceiving, light-ningproof & anti-electrostatic 5. Onboard digital isolation chip, safer signal isolation communication and better stability and anti-interference 6. Reserved control pins, allows to work with other control boards 7. Comes with development resources and manual (examples in python)Specifications1. CAN Controller: MCP2515 2. CAN transceiver: SIT65HVD230DR 3. RS485 transceiver: SP3485 4. Working voltage: 3.3V 5. Mounting hole size: 3.0mm 6. Dimensions: 100 x 79 mmPackage List1. RS485 CAN for Jetson Nano x1 2. Screws pack x1

Read more less

About The ProtuctThe PI4-CASE-ARGON-ONE-M.2 metal case can greatly speed up the boot and storage speed of the Raspberry Pi, which is to extend the M.2 interface through the USB interface and use an external SSD as the main storage drive. In this case, the Raspberry Pi 4 can be booted through the USB interface, which greatly improves the reading and writing speed and makes the boot speed much faster than using the SD card.Features1. Aluminum alloy material, modern space grey finish, robust and nice looking 2. Magnetic Design: Magnetic removable top and well designed GPIO header 3. M.2 Expansion Slot: Support M.2 modules like M.2 SSD, which is then connected to the Pi by USB adapter 4. Active + Passive Cooling: The whole case top acts as a Passive cooling for the Raspberry Pi, combined With the Included cooling fan and multiple airflow vents, brings excellent cooling effect 5. Neat Cable Management: All of the ports are accessed at the back, minimal cable clutter 6. Proper Bottom Design: Two airflow vents and four nonskid feet, simple but useful 7. Easy Assembly: Just a few steps to go, no messy wiring, no wrong connection, more stable, more safe

Read more less

FeaturesThe Compute Module PoE Board is a development board that you can plug a Raspberry Pi Compute Module into, and make use of the resources of Pi more flexibly. With the PoE (Power over Ethernet) feature, and versatile onboard peripheral interfaces, it is suitable for evaluating the Raspberry Pi compute module, also is an ideal choice for end products. 1. Raspberry Pi GPIO header, for connecting sorts of Raspberry Pi HATs. 2. 10/100M auto-negotiation Ethernet port, with PoE enabled. 3. 4 x USB ports, which allows connecting more USB devices. 4. 2 x CSI camera interfaces. 5. Onboard HDMI / DSI interfaces for connecting displays. 6. Onboard USB TO UART, for serial debugging. 7. Cooling fan interface, autorun on power-up OR controlled by IO pins. 8. Adopt isolated SMPS (Switching mode power supply).Specifications1. Power supply: Micro USB port / PoE Ethernet port 2. PoE power input: 37V ~ 57V DC in 3. PoE power output: 5V 2.5A DC out 4. Operating Temperature: -25 degree C ~ 80 degree C 5. Network standard: 802.3af PoE standard 6. Dimensions: 144mm x 88mm 7. Mounting hole size: 3.2mm

Read more less

1. ABS protection case For Raspberry Pi Zero Series, Fits Zero / Zero 2 W 2. Protective cover is sturdy and long-lasting, designed with compact size and light weight. 3. Precise Opening Design: Reversed GPIO slot and openings for sorts of connectors 4. Easy to install 5. Package Content: - Raspberry Pi Zero case x 1 - Screwdriver x 1 - Screws pack x 1

Read more less

About The ProtuctLD19 is mainly composed of laser ranging core, wireless transmission unit, wireless communication unit, angle measuring unit, motor driving unit, and mechanical housing.The LD19 ranging core adopts DTOF technology to measure 4500 times each second. When it works, LD19 emits the infrared laser forward, the laser is reflected to the single photon receiving unit after encountering the target object. Thus, we get both time of laser emitting and receiving, the gap between them is time of flight. With the light speed, we can calculate the distance.After receiving distance data, LD19 will combine them with angel value getting from angle measurement unit to comprise the points cloud data, then transmitting the points cloud data to external interface via wireless communication. Meanwhile, the external interface provides PWM to allow the motor driving unit to drive the motor. After the external control unit gets the rotational speed , it will reach to specified speed through PID algorithm closed-loop control to ensure LD19 work stably.Features1. Based on TOF (Time of Flight) laser ranging technology 2. Support UART communication 3. Measuring radius 12m 4. 30K Lux anti-glare interference 5. 4500Hz measurement frequency 6. 360 degree scanning range 7. Laser Safety Meets FDA Class 1 Standards 8. Compact appearance 9. 10000+ hours service lifeSpecifications1. Ranging Distance: 0.02 ~ 12.00 m 2. Ranging Average accuracy: +/-45 mm (within 0.3~12.00m) 3. Sweep Frequency: 5 ~ 13 Hz (Typ 10) 4. Scanning Angle: 360 degrees 5. Ranging Frequency: 4500 Hz 6. Resolution: 15mm 7. Wavelength: 895 ~ 915 nm (Typ 905) 8. Communication interface: UART 230400 9. Ambient Light Resistance: 30 KLux 10. Power Supply: 5V 11. Power Consumption: About 0.9W 12. Operating Current: 180mA 13. Operating Temperature: -10 degree C ~ 40 degree C 14. Lifetime: 10000+ hours 15. Dimensions: 54.00 x 46.29 x 34.80mm 16. Weight: 47gPackage List1. DTOF LIDAR LD19 x 1 2. Adapter x 1 3. USB cable 50cm x 1 4. 4 Pin cable 100mm x 1

Read more less

Features1. 13.3 inch IPS screen,1920 x 1080 high resolution. 2. Embed Raspberry Pi 3A+ as controller 3. One-way mirror, can display news, weather and time. 4. Toughened glass capacitive touch panel, 6H hardness, supports up to 10-points touch. 5. Embedded ferrite Hi-Fi speaker. 6. Embedded Microphone And Speaker, Adopts Snowboy Hotword Detection Engine. 7. 75 x 75mm spacing mounting holes (M4 screw hole) for a general wall mount. 8. Comes with a 75 degree tilt angle stand.Package List1. 13.3 inch Magic Mirror x 1 2. 12V power adapter x 1 3. Card reader x 1 4. Micro SD card x 1

Read more less

Features1. Mini computer chassis, robust and dust-proof, nice looking 2. Tailored For Compute Module 4 IO Board: Make it easy to build your own Raspberry Pi CM4 mini PC 3. Break-out 40PIN GPIO Header: The standard 40 PIN GPIO header is still available, make it easy to connect sorts of HATs 4. Precise cut-out with clear label: Each cut-out Is completely aligned with the connector 5. Come with cooling fan, combined with airflow vent, better heat dissipation 6. Application: Binocular vision, PoE powered Raspberry Pi Projects, or other industrial contextPackage List1. Metal case (top and bottom) x 1 2. 40PIN GPIO adapter x 1 3. Fan-4010-PWM-12V x 1 4. Screwdriver x 1 5. Screws pack x 1

Read more less

Features1. Build a shiny mini computer with this decent aluminum case custom made for the Raspberry Pi 4 2. Stylish Aluminum Alloy Housing: Aluminum housing with modern space grey finish, sturdy and beautiful 3. Removable Top and GPIO Recess: The neat GPIO recess and magnetic removable top are both beautiful and protective, and there are even clear pin labels and color-coded headers to make it easier to use 4. "Always on" feature: automatically starts the Pi and runs the fan on power up, enabled via jumper 5. Amazing temperature management: The extended post makes the aluminum case a large heat sink to transfer heat from the board, combined with a cooling fan and multiple vents, the cooling canot be better 6. Neat cable management: All ports are accessed at the back, minimizing cable clutter 7. Safe and convenient power button: Dedicated power button, combined with a one-line script, turns the computer on/off while keeping the stored files safe, and also supports custom functions 8. Easy to assemble, no messy lines: comes with two PCB boards, easy to build, no messy lines, no wrong connections, more stable and safer 9. Proper bottom design: TF card slot on bottom, as well as two vents and four rubber feet

Read more less

Features1. 13.3 inch IPS screen,1920 x 1080 high resolution. 2. Embed Raspberry Pi 3A+ as controller. 3. Toughened glass capacitive touch panel, 6H hardness, supports up to 10-points touch. 4. Embedded ferrite Hi-Fi speaker. 5. Embedded microphone and speaker, adopts snowboy hotword detection engine. 6. 75x75mm spacing mounting holes (M4 screw hole). 7. Comes with a 75 degree tilt angle stand.Package List1. 13.3 inch PiPad x 1 2. 12V power adapter x 1 3. Card reader x 1 4. Micro SD card x 1

Read more less

1. Only compatible with Raspberry Pi 4B2. ABS material shell and two transparent acrylic side panels3. A 0.96-inch OLED screen has been installed on the shell, 28 x 64 pixels, and the default I2C address: 0x3C4. M.2 SATA SSD 2280/2260/2240 mass storage adapter board, supports M.2 SATA SSD up to 2TB5. Note: Raspberry Pi 4B is not included

Read more less

Features:1. 10.3-inch e-ink display with a resolution of 1872 x 1404 (226DPI)2. Display advantages: Eye care, no blue light, close to the paper-like experience3. Display Environment: Visible under ambient light4. Display mode: Passively reflective5. Support mode and contrast adjustment6. Support Raspberry Pi, Jetson Nano, and computersSpecification:1. Resilution: 1872 x 1404 pixel2. PPI: 2273. Panel: Anti-glare toughen glass4. Refresh Rate: 15Hz (the maximum refresh rate of A2/A2+ mode)5. Aspect Ratio: 4:36. Display Dimension: 209.66 x 157.25 mm7. Outline Dimension: 228 x 185.7 mm8. Thickness:9 mm9. Net Weight: 433g10. Vesa Stand Hole Spacing: 50mmPackage List:1. EINK-DISP Monitor x 12. Mini HDMI to HDMI cable 1.5m x 13. HDMI to Micro HDMI Adapter x 14. 5V 3A Power Adapter x 15. Package Box x 16. Leather Case x 1

Read more less

Features:1. 13.3-inch e-ink display with a resolution of 1600 x 1200 (150DPI)2. Display advantages: Eye care, no blue light, close to the paper-like experience3. Display Environment: Visible under ambient light4. Display mode: Passively reflective5. Support mode and contrast adjustment6. Support Raspberry Pi, Jetson Nano, and computersSpecification:1. Resilution: 1600 x 1200 pixel2. PPI: 1503. Panel: Anti-glare toughen glass4. Refresh Rate: 15Hz (the maximum refresh rate of A2/A2+ mode)5. Aspect Ratio: 4:36. Display Dimension: 270.4 x 202.8 mm7. Outline Dimension: 305 x 225.9 mm8. Thickness:9 mm9. Net Weight: 685g10. Vesa Stand Hole Spacing: 75mmPackage List:1. EINK-DISP Monitor x 12. Mini HDMI to HDMI cable 1.5m x 13. HDMI to Micro HDMI Adapter x 14. 5V 3A Power Adapter x 15. Package Box x 16. Leather Case x 1

Read more less

1. Size: 5.5 inches2. Port: HDMI3. Display panel: IPS, 2K resolution4. Touch port: USB5. Support Raspberry Pi operating system, 10-point touch.6. Support Ubuntu / Kali, single touch.7. Only Raspberry Pi 4B and CM4 have enough CPU performance to fully drive this 2K monitor8. When using Raspberry Pi 3B+/Pi 3B/Zero 2w/Zero w, only the default portrait display is supported and cannot be rotated.9. This chassis only supports Raspberry Pi 4B

Read more less

1. 5G standard: 3GPP R162. Chip: Qualcomm Snapdragon X623. Operating system: for Windows/Linux/Android4. Dialing: RNDIS, NDIS, PPP, MBIM5. SIM card: 1.8V/2.95V6. Power supply: 3.135-4.4V7. Standard M.2 interface8. High throughput data communication9. The AT command of SIM8262E-M2 is compatible with SIM7912G/SIM8200X-M2 series modules

Read more less

1. 2.8 inch IPS screen, 640 x 480 pixels, 70% NTSC color gamut.2. Enjoys a smooth gaming experience with 60fps.3. Optical bonding toughened glass panel with anti-fingerprint technique.4. Compatible with Raspberry Pi Zero 2 W.5. Battery indicator light for checking the power of the game console easily.6. Update ROMs via WiFi.Specifications:1. Controller:- Raspberry Pi Zero 2 W-- BCM2710A1 quad-core 64-bit SoC (Arm Cortex-A53 @1GHz)-- 512MB LPDDR2 SDRAM-- 2.4GHz IEEE 802.11b/g/n Wireless LAN, Bluetooth 4.2, BLE2. Display:- 2.8 inch IPS Screen-- 640 x 480 pixels-- Fully laminated toughened glass panel, anti-fingerprint technique-- 70% NTSC color gamut3. Battery: 1500 mAh4. Storage: 32G TF card5. Size: 136.4 x 67.5mmPackage List:1. GPM280 main unit x12. Assembled, with Raspberry Pi Zero 2 W and 32GB TF card3. Screwdriver x14. Power adapter 5V 3A x15. Card reader x16. Cleaning cloth x1

Read more less

1. Dedicated all-In-one aluminum alloy cooling fan for Raspberry Pi 4B, PWM speed adjustment, better cooling, low noise, space saving2. This is a thin and lightweight heat sink, equipped with a 3510 ultra-quiet cooling fan, and the fan supports PWM speed regulation, which is perfectly compatible with Raspberry Pi OS. Other systems need to manually write python or C code to drive the fan speed through PWM.3. NOTE: Supports Raspberry Pi 4B Only, Automatic speed control function only supports Raspberry Pi OS.Specifications:1. Supported Pi: Raspberry Pi 4 Model B 1GB/2GB/4GB/8GB version2. Power supply: DC 5V input (can be powered by Raspberry Pi)3. Interface: 3-wire PWM speed control fan connector4. Rated power: 0.3W (5V, 0.6+/-0.02A)5. Cable length: 80+/-10mm6. Fan: 5500+/-10%RPMPackage List:1. PI4-FAN-PWM x12. Silicone thermal tape x4 and Screw x2

Read more less

1. Rated power: 3.3V/5V2. Interface: 3-wire SPI, 4-wire SPI3. Full refresh time: 3414. Refresh power: about 61.7mW5. Dot pitch: 0.176 × 0.176mm6. Standby current: about 0.01uA7. Without backlight, the last content can be displayed for a long time even if the power is cut off.8. Ultra-low power consumption, basically only need to refresh.9. SPI interface for connecting Raspberry Pi / Jetson Nano / Arduino / STM32 and other controller boards.10. On-board voltage converter, compatible with 3.3V/5V MCU.

Read more less

1. No backlight, keeps displaying last content for a long time even when power down 2. Ultra low power consumption, basically power is only required for refreshing 3. Come with development resources and manual(driver board schematic, examples for Raspberry Pi/Arduino/STM32) Specifications: 1. Operating voltage: 3.3V 2. Interface: 3-wire SPI, 4-wire SPI 3. Outline dimension: 68.1 x 37.9 x 0.85mm 4. Display size: 52.096 x 29.568mm 5. Dot pitch: 0.176 x 0.176mm 6. Resolution: 296 x 168 pixels 7. Display color: Red/Yellow/Black/White 8. Grey level: 2 9. Full refresh time: 12s 10. Refresh power: Less than 57mW (typ.) 11. Standby power: Less than 0.01uA (almost none) 12. Viewing angle: Greater than 170 degree

Read more less

The STLINK-V3MINIE is a stand-alone debugging and programming tiny probe for STM32 microcontrollers, portable and easy-to-use. Onboard JTAG/SWD interfaces for communicating with STM32 microcontroller, also provides a virtual COM port for the host PC to communicate with the target microcontroller through one UART. Features: 1. Tiny 15 mm x 42 mm stand-alone debugging and programming probe for STM32 microcontrollers 2. Self-powered through a USB Type-C connector 3. USB 2.0 high-speed interface 4. Probe firmware is updatable through USB 5. Support drag-and-drop Flash programming of binary files 6. Two color LEDs: communication, power 7. JTAG communication support up to 21 MHz 8. SWD (Serial Wire Debug) and SWV (Serial Wire Viewer) communication support up to 24 MHz 9. Virtual COM port (VCP) up to 15 Mbps 10. 1.65 to 3.60 V application voltage support

Read more less

Features1. 5.5-inch IPS display with a hardware resolution of 1440 ?? 2560 2. 10-point capacitive touch control with toughened glass panel, hardness up to 6H 3. Adopt the optical bonding touch technique for better use 4. Support Raspberry Pi OS / Ubuntu / Kali and Retropie when working with Raspberry Pi 4B 5. Support Windows 11/10/8.1/8/7 when working as a computer monitor 6. Support HDMI audio output with 3.5mm Jack and 4PIN headerDevice & System Support1. For the moment, only the Raspberry Pi 4B and CM4 have adequate CPU performance to drive this 2K display completely. 2. Support more powerful future versions as long as its GPU performance is equivalent to or better than the Pi 4B. 3. Limited by the hardware, when working with Raspberry Pi 3B+/Pi 3B/Zero 2w/Zero w, only supports default portrait display and cannot be rotated. 4. The case only supports Raspberry Pi 4B.Package List1. 5.5 inch 1440x2560 LCD x1 2. HDMI cable x1 3. USB type A plug to micro B plug cable x1 4. USB adapter (B) x1 5. HDMI adapter (B) x1 6. HDMI to Micro HDMI adapter (C) x1 7. USB adapter (D) x1 8. Screws pack x1

Read more less

1. Working voltage: 3.3V/5V2. Interface: 3-wire SPI, 4-wire SPI3. Gray scale: 24. Full refresh time: 3215. Refresh power: about 57mW6. Dot pitch: 0.176 × 0.176mm7. Standby current: about 0.01uA8. Resolution: 296×168 pixels9. Without backlight, the last content can be displayed for a long time even if the power is cut off.10. Ultra-low power consumption, basically only need to refresh.11. SPI interface for connecting Raspberry Pi / Jetson Nano / Arduino / STM32 and other controller boards.12. Onboard voltage converter, compatible with 3.3V/5V MC.

Read more less

1. Input interface: HDMI x 32. Support 4K/2K 30Hz3. Built-in input equalizer, can automatically adjust the input signal4. Output interface: HD x15. Built-in output drive regulator, which can automatically adjust the output signal amplitude6. Support HDMI 1.4b and DVI1.0 standard7. Transmission speed: up to 3Gbps

Read more less

1. Power supply: 9-24V2. Communication interface: RS485 port x 1, Ethernet port x 13. Baud rate: 300-115200 bps4. Data bits: 5-9 bits5. Configuration: host, web browser, device management function library6. Communication method: TCP/IP direct communication, VCOM7. Working temperature: -40 degrees to 85 degrees8. Main function: Bidirectional transparent data transmission between RS485 and Ethernet9. It is easy to combine multi-rail installed serial servers together, more freedom.10. It is suitable for Modbus grid upgrade and can be used in conjunction with 3D configuration software.11. Support TCP server / TCP client / UDP mode / UDP multicast.12. Multi-host rolling polling support, easy for cloud communication and device identification.

Read more less

This is a MIPI_CSI camera with 5MP and 70 degree FOV. The onboard optical image stabilization camera module supports dual-axis image stabilization+/-5 degree compensation angle. Suitable for motion cameras, robots, wearables, and so on. Support Raspberry Pi, and Sunrise X3 Pi. Specifications: 1.Sensor :OV5647 2. CMOS Size: 1/4 inch 3. Pixel: 5MP 4. Aperture: F 2.8 5. Focal Length: 3.2mm 6. Angle of View: 70 degrees 7. Stabilization Type: OIS (Optical Image Stabilization) Stabilization 8. Focusing: Fixed focus 9. Distortion: Less than 1.0% 10. Range: XY axis +/- 5 derees 11. Image: 2592 x 1944 still image resolution 12. Video recording: 1920 x 1080p 30fps, 1280 x 720p 60fps, 640 ?? 480p 60fps, 640 x 480p 90fps

Read more less

About The Product1. The case is currently only compatible with the old version of the Jetson Nano Developer Kit B01, which is made from Waveshare. Other third-party kits or the new version of the Jetson Nano Developer Kit B01 are not currently supported. 2. The difference between the new version of the Jetson Nano Developer Kit B01 and the old version of the Developer Kit B01: - Please pay attention to checking the HDMI and DP sockets of the kit. If the HDMI/DP socket covered with a metal outer layer is a new version. But this case is not currently supported. If there is no metal cladding on the sockets--the old version of the B01 kit, the case can be supported. - If you are using the A02 version of the Jetson Nano developer kit, note that the positions of the button interfaces are different.Features1. High-quality aluminum Case Designed for the Jetson Nano 2. Chamfered corners, more comfortable and smoother 3. Reserved airflow outlets on three sides, and built-in fan is opened on the top for excellent heat dissipation 4. Exquisite workmanship, beautiful fit 5. Equipped with silicone non-slip feet, more stable placement: Reduce the heat dissipation of the bottom contact areaPackage List1. Aluminum body case(top and bottom) x 1 2. GPIO adapter x 1 3. Button cable x 1 4. Nonskid feet 4pcs x 1 5. Button 2pcs x 1 6. Button board x 1 7. Allen spanner x 1 8. Allen screws pack x 1

Read more less

Features:1. 10.3-inch e-ink display with a resolution of 1200 x 825 (150DPI)2. Display advantages: Eye care, no blue light, close to the paper-like experience3. Display Environment: Visible under ambient light4. Display mode: Passively reflective5. Support mode and contrast adjustment6. Support Raspberry Pi, Jetson Nano, and computersSpecification:1. Resilution: 1200 x 825 pixel2. PPI: 1503. Panel: Anti-glare toughen glass4. Refresh Rate: 15Hz (the maximum refresh rate of A2/A2+ mode)5. Aspect Ratio: 16:116. Display Dimension: 202.8 x 139.425 mm7. Outline Dimension: 238.3 x 168 mm8. Thickness:9.5 mm9. Net Weight: 501g10. Vesa Stand Hole Spacing: 50mmPackage List:1. EINK-DISP Monitor x 12. Mini HDMI to HDMI cable 1.5m x 13. HDMI to Micro HDMI Adapter x 14. 5V 3A Power Adapter x 15. Package Box x 16. Leather Case x 1

Read more less

About The ProductThis is an AI Racing Robot kit based on Jetson Nano Developer Kit. Supports deep learning, auto line following, autonomous driving and so on.Specifications1. Camera: 8MP HD resolution, 160 degree FOV wide angle camera 2. OLED: 0.91 inch 128 x 32 pixels 3. Wireless: AC8265 4. Driving Type: Ackerman steering / Dual gearmotor rear wheel drive 5. Power supply: 12.6V, 18650 battery x 3 (connected in series). Note: the 18650 batteries are NOT included. 6. Motor: - 37-520 DC gearmotor - Reduction rate 1:10 - Idle speed 740RPM 7. Chassis: Aluminum alloy chassis 8. Program library: JetRacer, DonkeyCar 9. Suggestion: Competition level; Experienced programming skill requiredPackage List2. EVA felt pad 2PCS 3. 3D-printed motor lid 4. JetRacer expansion board 5. IMX219-160 Camera 6. Wireless-AC8265 7. Acrylic piece 8. Servo mount 9. Metal Gearmotor 2PCS 10. Tire 4PCS 11. Coupler 2PCS 12. MG996R servo 13. MG996R servo wheel 14. Steering knuckle 2PCS 15. Ball bearing 4PCS 16. M3 plastic ball joint 4PCS 17. M3 pull bar 2PCS 18. 12.6V battery charger + EU head 19. Wireless gamepad 20. 6Pin cable 21. Spanner 2PCS 22. Screwdriver 2PCS 23. Mini cross wrench sleeve 24. 4010 cooling fan 25. Micro SD card reader 26. Screws pack 27. Track map

Read more less

FeaturesSmart robot is project of electronic enthusiasts, and there have been several robots based on Raspberry Pi Zero W, 3B+, 4B in Waveshare product line. Now, here comes the Pico version: PicoGo! The PicoGo is a smart mobile robot based on Raspberry Pi Pico, it includes ultrasonic module, LCD module, Bluetooth module, line following module, and obstacle avoidance module, all these functions are highly integrated for easily achieving IR obstacle avoidance, auto line following, BT/IR remote control, and more. With various advanced features, it will help you fast get started with smart robot design and development. PicoGo smart mobile robot features: 1. Standard Raspberry Pi Pico header, supports Raspberry Pi Pico series 2. Battery protection circuit: over charge/discharge protection, over current protection, short circuit protection, reverse proof, more stable and safe operating 3. Recharge/Discharge circuit, allows programming/debugging concurrently while recharging 4. 5-ch infrared sensor, analog output, combined with PID algorithm, stable line tracking 5. Onboard multiple smart robot sensors like line tracking, obstacle avoidance, no more messy wiring 6. 1.14 inch IPS colorful LCD display, 240 x135 pixels, 65K colors 7. Integrates BT module, allows teleoperations like robot movement, RGB LED display color, buzzer, etc. by using mobile phone APP 8. N20 micro gearmotors, with metal gears, low noise, high accuracy 9. Colorful RGB LED, pretty cool! Raspberry Pi Pico controller board features: 1. RP2040 microcontroller chip designed by Raspberry Pi in the United Kingdom 2. Dual-core Arm Cortex M0+ processor, flexible clock running up to 133 MHz 3. 264KB of SRAM, and 2MB of on-board Flash memory 4. USB 1.1 with device and host support 5. Low-power sleep and dormant modes 6. Drag-and-drop programming using mass storage over USBPackage List1. Raspberry Pi Pico (pre-soldered header) x1 2. PicoGo base board x1 3. PicoGo acrylic panel x1 4. 1.14inch LCD Module x1 5. Ultrasonic sensor x1 6. 5V 3A power supply x1 7. IR remote controller x1 8. USB-A to micro-B cable 1.2m x1 9. PH2.0 8Pin cable 5cm opposite side headers x1 10. Mini cross wrench sleeve x1 11. Screwdriver x1 12. Screws and standoffs pack x1

Read more less

FeaturesSmart robot is project of electronic enthusiasts, and there have been several robots based on Raspberry Pi Zero W, 3B+, 4B in Waveshare product line. Now, here comes the Pico version: PicoGo! The PicoGo is a smart mobile robot based on Raspberry Pi Pico, it includes ultrasonic module, LCD module, Bluetooth module, line following module, and obstacle avoidance module, all these functions are highly integrated for easily achieving IR obstacle avoidance, auto line following, BT/IR remote control, and more. With various advanced features, it will help you fast get started with smart robot design and development. PicoGo smart mobile robot features: 1. Standard Raspberry Pi Pico header, supports Raspberry Pi Pico series 2. Battery protection circuit: over charge/discharge protection, over current protection, short circuit protection, reverse proof, more stable and safe operating 3. Recharge/Discharge circuit, allows programming/debugging concurrently while recharging 4. 5-ch infrared sensor, analog output, combined with PID algorithm, stable line tracking 5. Onboard multiple smart robot sensors like line tracking, obstacle avoidance, no more messy wiring 6. 1.14 inch IPS colorful LCD display, 240 x135 pixels, 65K colors 7. Integrates BT module, allows teleoperations like robot movement, RGB LED display color, buzzer, etc. by using mobile phone APP 8. N20 micro gearmotors, with metal gears, low noise, high accuracy 9. Colorful RGB LED, pretty cool! Raspberry Pi Pico controller board features: 1. RP2040 microcontroller chip designed by Raspberry Pi in the United Kingdom 2. Dual-core Arm Cortex M0+ processor, flexible clock running up to 133 MHz 3. 264KB of SRAM, and 2MB of on-board Flash memory 4. USB 1.1 with device and host support 5. Low-power sleep and dormant modes 6. Drag-and-drop programming using mass storage over USBPackage List1. Raspberry Pi Pico (pre-soldered header) x1 2. PicoGo base board x1 3. PicoGo acrylic panel x1 4. 1.14inch LCD Module x1 5. Ultrasonic sensor x1 6. 5V 3A power supply x1 7. IR remote controller x1 8. USB-A to micro-B cable 1.2m x1 9. PH2.0 8Pin cable 5cm opposite side headers x1 10. Mini cross wrench sleeve x1 11. Screwdriver x1 12. Screws and standoffs pack x1

Read more less

Features1. Onboard three 18650 batteries, 7800mAh, up to 12.6V voltage output, and stronger motor power (not included batteries). 2. Onboard S-8254AA + AO4407A lithium battery protection circuit, with anti-overcharge, anti-over-discharge, anti-over-current and short-circuit protection functions. 3. The onboard APW7313 voltage regulator chip can provide a stable 5V voltage to the Jetson Nano. 4. The onboard TB6612FNG dual H-bridge motor driver chip can drive the left and right motors to work. 5. Onboard 0.91-inch 128 x 32 resolution OLED, real-time display of car IP address, memory, power, etc. 6. The onboard ADS1115 AD acquisition chip is convenient for real-time monitoring of battery power.Package List1. Jetson Nano 2GB Developer Kit 2. Micro SD Card 64GB 3. JetRacer metal kit 6PCS 4. EVA felt pad 2PCS 5. 3D-printed motor lid 6. JetRacer expansion board 7. IMX219-160 Camera 8. USB wireless NIC 9. Acrylic piece 10. Servo mount 11. Metal Gearmotor 2PCS 12. Tire 4PCS 13. Coupler 2PCS 14. MG996R servo 15. MG996R servo wheel 16. Steering knuckle 2PCS 17. Ball bearing 4PCS 18. M3 plastic ball joint 4PCS 19. M3 pull bar 2PCS 20. 12.6V 2A battery charger + EU head 21. Wireless gamepad 22. 6Pin cable 23. Spanner 2PCS 24. Screwdriver 2PCS 25. Mini cross wrench sleeve 26. 4010 cooling fan 27. Micro SD card reader 28. Screws pack 29. Track map

Read more less

About The ProtuctThis is an AI Racing Robot kit based on Jetson Nano 2GB Developer Kit. Supports deep learning, auto line following, autonomous driving, and so on.NoticeWe do not provide batteries in the AI Kit or the Acce Package because of the shipping policy, you need to buy batteries in the local market.Specifications1. Camera: 8MP HD resolution, 160 degree FOV wide angle camera 2. OLED: 0.91 inch 128 x 32 pixels 3. Wireless: USB 4. Driving Type: Ackerman steering / High speed motors 4WD / Front and rear axle differentials 5. Shock Absorber: Adjustable oil-filled shocks / 4WD independent suspension 6. Power supply: 8.4V, 18650 battery x 4 (two in parallel, two in series). Note: the 18650 batteries are NOT included. 7. Servo: 6kg/cm torque 8. Chassis: Quality rugged plastic chassis 9. Crashproof: Front sponge 10. Program library: JetRacer, DonkeyCar 11. Suggestion: Competition level; Experienced programming skill requiredPackage List1. Jetson Nano 2GB Developer Kit 2. Micro SD Card 64GB 3. On-road chassis 4. JetRacer Pro expansion board 5. USB wireless NIC 6. IMX219-160 Camera 7. Acrylic camera spacer 8. Camera holder 9. Wireless gamepad 10. Cooling fan 11. 6Pin cable 12. Micro SD card reader 13. Spanner 14. Screwdriver x2 15. 8.4V 2A battery charger + EU head 16. Screws pack 17. Track map

Read more less

Features1. Allows controlling up to 253 SC, ST series serial bus servos at the same time (adequate power supply required) 2. Wide range voltage input 6-12V (the input voltage and the servo voltage must be matched) 3. Built-in WiFi and Bluetooth, as well as ESP-NOW support, for remote control and servo debugging 4. Automatic download circuit for easy uploading programs 5. Open source web application and various robot structures 6. Compact size and space saving, suitable for integration into sorts of space-limited projectsSpecifications1. Power supply voltage: DC 6-12V 2. Power Connector: 5.5 x 2.1mm DC 3. Download interface: Type-C 4. Controller: ESP32 5. Control interface: UART 6. Dimensions: 30 x 65mm 7. Mounting hole size: 2.75mm 8. Mounting hole spacing: 23 x 58mmPackage List1. Servo Driver with ESP32 x 1 2. Screws pack x 1

Read more less

Features1. OV2640 camera and digital microphone, supports applications like image recognition, voice processing... 2. Standard 40PIN GPIO header, compatible with Raspberry Pi HATs for sorts of IoT applications 3. Integrated Li-ion battery boost charging manager, supports battery charging/discharging, can also be powered from USB connection 4. Compatible with Arduino and ESP-IDF software SDK, seamlessly connecting with ESP-WHO applications 5. Onboard 8MB PSRAM, 4MB FLASH storage, supports SD extension as well 6. CP2102 USB to UART converter, for serial debugging/programming 7. 4x LED indicators, make it easy to check the operating status 8. Comes with development resources and manualSpecifications1. WIFI: 802.11b/g/n 2. BT: V4.2 including legacy BR/EDR and BLE low energy 3. Processor: Xtensa LX6 dual-core processor 240MHz 4. Camera: OV2640 (UXGA 1622 x 1200) 5. SRAM: 520KB+8MB 6. Flash: 448KB+4MB 7. Input voltage: 3.3V~5V 8. Working voltage: 3.3V 9. Charging current: 1A 5V 10. Overall consumption: 7.7mA 5V (ESP32 deep sleep) 11. Dimensions: 65mm x 30.5mm 12. Working temperature: -40 degree C ~ 85 degree CPackage List1. ESP32 One main unit x 1 2. USB-A to micro-B cable x 1 3. Screws pack x 1

Read more less

About The Product1. Multi-function time relay module, 5~30V wide voltage power supply, MOS tube control output, no contact, no ignition, little interference. 2. Up to 10A control capability. 3. There are up to 31 working modes to meet various testing and automatic control applications. 4. The delay time is adjustable from 0.01 second to 999 minutes. 5. The trigger port can be triggered by a voltage signal or by connecting a button.Specifications1. Power supply voltage: 5~30V 2. Trigger terminal voltage: DC 3.3~30V (can also be triggered by button) 3. Control current: 10A 4. Module size: 63 x 42 x 14mm (length, width and height)Using tips1. Setting of working parameters: Press and hold the S1 button without letting go, the display will show P-xx after 0.5 seconds, press S2 and S3 to change the working mode. 2. After selecting the working mode, short press the S1 key to enter the A time setting, and the screen displays Axxx. At this time, press the S2 and S3 keys to modify the A time parameter. Short press the S2 and S3 keys to add or subtract 1, and long press to quickly add or subtract 10. 3. Press the S4 key to set the position of the decimal point. After setting the A time, press the S1 key to set the B time, and the screen displays bxxx. At this time, press the S2 and S3 keys to modify the B time parameter. 4. Short press the S2 and S3 keys to add or subtract 1, and long press to quickly add or subtract 10. Press the S4 key to set the position of the decimal point. After setting the B time, press the S1 key to set the C time, the screen displays Cxxx, at this time press the S2 and S3 keys to modify the c time parameter, short press the S2 and S3 keys to add or subtract 1, long press to quickly add or subtract 10, Press the S4 key to set the position of the decimal point. 5. After setting the c time, press the S1 key to enter the most setting of the d parameter. The d parameter is the number parameter, ranging from 1 to 999. After setting the d parameter, press the S1 key one last time to exit the setting state and save all parameters.Point Position1. Ax.xx The decimal point is in hundreds, and the time range is 0.01~9.99 seconds 2. Axx.x The decimal point is in the tens place, and the time range is 0.1~99.9 seconds 3. Axxx. The decimal point is in the ones place, and the time range is 1~999 seconds 4. Axxx has no decimal point and the time range is 1~999 minutes 5. Turn off the display: In the non-setting state, press the S4 key to turn off the display, and then press it to turn it on again.

Read more less

1. Good condition,with high quality ,great performance2. Cooling fan run smoothly, long life keep CPU safe without overheating3. Compatible with Raspberry Pi CM4 robotic projects and development boardsSpecification:1. Rated Power: 1W (5V, 0.2+/-0.02A); 1.62W (for 12V, 0.135+/-0.02A)2. Rated Speed: 5000+/-10%RPM( for 5V); 8000+/-10%RPM ( for 12V)3. General: Low-profile, PWM speed adjustment4. Interface: 4-wire PWM speed-adjustable fan header5. Cable length: 90+/-10mm6. Size: 54 x 39 x 13mmPackage List:1. CM4-FAN-3007 x 12. Screws and thermal tapes x 1

Read more less

1. Good condition,with high quality ,great performance2. Cooling fan run smoothly, long life keep CPU safe without overheating3. Compatible with Raspberry Pi CM4 robotic projects and development boardsSpecification:1. Rated Power: 1W (5V, 0.2+/-0.02A); 1.62W (for 12V, 0.135+/-0.02A)2. Rated Speed: 5000+/-10%RPM( for 5V); 8000+/-10%RPM ( for 12V)3. General: Low-profile, PWM speed adjustment4. Interface: 4-wire PWM speed-adjustable fan header5. Cable length: 90+/-10mm6. Size: 54 x 39 x 13mmPackage List:1. CM4-FAN-3007 x 12. Screws and thermal tapes x 1

Read more less

1. All ports and slots of the aluminum alloy case can match with for Raspberry Pi Zero 2 W computer 2. Add 40 Pin Headers to extend the GPIO pin and insert GPIO cable. 3. Open case design, donot need to worry about affect wifi signal 4. It is a good raspberry pi zero heatsink case with good heat dissaption 5. Reinforced aluminum material, lightweight and durable, long-lasting stainless 6. With thermal pad to touch the shell body for heat dissipation.

Read more less