Products

1. POE: Integrates 802.3af-compliant PoE circuit (5V/2.5A) 2. USB: USB 2.0 x 4 3. GPIO: Raspberry Pi 40 PIN GPIO x 1 4. Header: - RS485 x 1 - RS232 x 1 - PCIe Gen 2 x 1 5. HD media interface: HDMI x 2, supports 4K 30fps output 6. DSI display: MIPI DSI x 2 (15pin 1.0mm FPC) 7. CSI camera: MIPI CSI-2 x 2 (15pin 1.0mm FPC) 8. Power input: 5V 9. FAN: 5V / 12V (Allows speed adjustment and measurement) 10. RTC: Real-time clock with battery socket and ability to wake Compute Module 4 11. RJ45 Ethernet: Gigabit Ethernet 12. CM4 slot: Suitable for all variants of Compute Module 4 13. SD card slot: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 14. Size: 124.50 x 108.80mm

Read more less

OverviewThis is an edge connector expansion board designed for micro:bit, breakout the I/O pins to 2.54mm pitch pinheaders for easy use.SpecificationsDimension: 82.05mm x 36.10mmThrough holes diameter: 2mm

Read more less

About The ProductThe Core1262-868M is a LoRa core module which incorporates new-generation SX1262 chip. It has featuress including mini size, long range transmission, high anti-interference capability, and so on. The module uses EU868 band, combined with LoRa gateway, it can be connected to servers like TTN server to build LoRa network. 1. New-generation SX1262, higher power efficiency and longer transmission distance than the traditional SX1278 2. EU868 band, combined with LoRa gateway, quick connection to cloud servers like TTN server 3. Comes with rich development resources and manual (examples for STM32, Raspberry Pi Pico)Specifications1. RF chip: SX1262 2. Frequency range: EU868 (863~870MHz) 3. Modulation: LoRa/(G)FSK 4. Data rate: 0.018~62.5Kbps (LoRa), 0.6~300Kbps ((G)FSK) 5. Emit power: More than 14dBm 3.3V 6. Spreadind factor: SF5 ~ SF12 7. Operating voltage: 3.3V 8. Module power consumption: Emitting current: 45mA 14dBm; receiving current: 5.3mA 125KHz 9. Communication bus: SPI 10. Operating temperature: -40 ~ 85 degree C 11. Connector: Castellated edge / solder holes 12. Dimensions: 21.00 x 52.00mm

Read more less

Overview1. Core405R is an STM32 MCU core board designed for STM32F405RGT6, supports further expansion. It is ideal for starting application development with STM32F family.2. Minimal ready-to-run system, integrates clock circuit, USB control circuit, USB connector, 3. etc.3. All the I/O ports are accessible on the pin headers4. JTAG/SWD programming/debugging interface5. 2.54mm header pitch, allowed to be plugged-in your application boardWhat has On Board1. STM32F405RGT6: The high performance STM32 MCU which features:- Core: Cortex-M4 32-bit RISC- Operating Frequency: 168MHz, 210 DMIPS/1.25 DMIPS/MHz- Operating Voltage: 1.8V-3.6V- Package: LQFP64- Memories: 1MB Flash, 192+4kB SRAM- MCU communication Interfaces:-- 3 x SPI, 4 x USART, 2 x UART, 2 x I2S, 3 x I2C, 1 x SDIO, 2 x CAN--1 x USB 2.0 HS/FS device/host/OTG controller with dedicated DMA, on-chip full-speed PHY--1 x USB HS ULPI (external PHY required)- AD & DA converters: 3 x AD (12-bit, 1μs, shares 16 channels); 2 x DA (12-bit)- Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP2. AMS1117-3.3: 3.3V voltage regulator3. MIC2075-2: onboard USB power management device4. Power supply switch, powered from 5Vin or USB connection5. Boot mode selection, for configuring BOOT0 pin6. Power indicator7. VBUS LED8. Reset button9. 8M crystal10. 32.768K crystal, for internal RTC with calibration11. JTAG/SWD interface: for debugging/programming12. USB connector, used for establishing USB communication between PC and the STM32 development board13. MCU pins expander, VCC, GND and all the I/O pins are accessible on expansion connectors for further expansion14. 5Vin pinheader, 5V power supply is required when using USB HOST/OTG15. USB jumper- Short the jumper when using USB- Open the jumper to disconnect from related I/O port16. VBAT selection jumper- Short the jumper to use system power supply- Open the jumper to connect the VBAT to external power, such as batteryPackage Contents1. Core405R x 12. USB type A to Mini-B cable x 13. Software CD x 1

Read more less

Overview1. Core407I is a small STM32 development board that features an STM32F407IGT6 device as the microcontroller, supports further expansion. It is ideal for starting application development with STM32F family.2. As a minimal ready-to-run system, the Core407I integrates USB communication interface, JTAG/SWD programming/debugging interface, clock circuit, USB power management, boot mode selection, and so on.3. Furthermore, pin headers on the backside allow the Core407I to be plugged-in your application board and act as the MCU core circuit in your system. All the I/O ports are accessible on the pin headers, and the header pitch is designed as 2.0mm to achieve smaller pcb size.What is On BoardSTM32F407IGT6 development board on board resource1. STM32F407IGT6: The high performance STM32 MCU which features:- Core: Cortex-M4 32-bit RISC- Feature: a full set of single-cycle DSP instructions- Operating Frequency: 168MHz, 210 DMIPS/1.25 DMIPS/MHz- Operating Voltage: 1.8V-3.6V- Package: LQFP176- Memories: 1024kB Flash, 192+4kB SRAM- MCU communication Interfaces:-- 3 x SPI, 4 x USART, 2 x UART, 2 x I2S, 3 x I2C-- 1 x FSMC, 1 x SDIO, 2 x CAN-- 1 x USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, ULPI and on-chip full-speed PHY-- 1 x 10/100 Ethernet MAC-- 1 x 8 to 14-bit parallel camera interface- AD & DA converters: 3 x AD (12-bit, 1μs, shares 24 channels); 2 x DA (12-bit)- Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP2. AMS1117-3.3 (on bottom side), 3.3V voltage regulator3. MIC2075 (on bottom side), onboard USB power management device4. Power supply switch, powered from 5V in or USB connection5. Boot mode switch, for configuring BOOT0 pin6. Power indicator7. VBUS LED8. Reset button9. 8M crystal oscillator (on bottom side)10. 32.768K crystal (on bottom side), for internal RTC with calibration11. JTAG/SWD interface: for debugging/programming12. USB interface- As DEVICE, used for establishing USB communication between PC and the STM32 development board- As HOST, connecting to USB devices such as USB flash drive through a USB OTG cable13. MCU pins expander, VCC, GND and all the I/O ports are accessible on expansion connectors for further expansion14. 5V in pinheader, 5V power supply is required when using USB HOST/OTG15. USB HOST/OTG jumper- Short the jumper when using USB HOST/OTG- Open the jumper to disconnect from I/O port16. VBAT selection jumper- Short the jumper to use system power supply- Open the jumper to connect the VBAT to external power, such as battery17. VREF selection jumper- Short the jumper to connect VREF+ to VCC- Open the jumper to connect VREF+ to other custom pin via jumper wirePackage Contents1. Core407I development board x 12. USB type A to Mini-B cable x 13. Software CD x 1

Read more less

Overview1. Core407V is a small STM32 development board that features an STM32F407VET6 device as the microcontroller, supports further expansion. It is ideal for starting application development with STM32F family.2. As a minimal ready-to-run system, the Core407V integrates USB communication interface, JTAG/SWD programming/debugging interface, clock circuit, USB power management, boot mode selection, and so on.3. Furthermore, pin headers on the backside allow the Core407V to be plugged-in your application board and act as the MCU core circuit in your system. All the I/O ports are accessible on the pin headers, and the header pitch is designed as 2.54mm.What has On Board1. STM32F407VET6: The high performance STM32 MCU which features:- Core: Cortex-M4 32-bit RISC- Feature: a full set of single-cycle DSP instructions- Operating Frequency: 168MHz, 210 DMIPS/1.25 DMIPS/MHz- Operating Voltage: 1.8V-3.6V- Package: LQFP100- Memories: 512kB Flash, 192+4kB SRAM- MCU communication Interfaces:-- 3 x SPI, 3 x USART, 2 x UART, 2 x I2S, 3 x I2C-- 1 x FSMC, 1 x SDIO, 2 x CAN-- 1 x USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, ULPI and on-chip full-speed PHY-- 1 x 10/100 Ethernet MAC-- 1 x 8 to 12-bit parallel camera interface- AD & DA converters: 3 x AD (12-bit, 1μs, shares 24 channels); 2 x DA (12-bit)- Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP2. AMS1117-3.3 (on bottom side): 3.3V voltage regulator3. MIC2075 (on bottom side): onboard USB power management device4. Power supply switch, powered from 5Vin or USB connection5. Boot mode switch, for configuring BOOT0 pin6. Power indicator7. Reset button8. 8M crystal oscillator9. 32.768K crystal (on bottom side), for internal RTC with calibration10. JTAG/SWD interface: for debugging/programming11. USB connector, used for establishing USB communication between PC and the STM32 development board12. IO expander (including VCC/GND), all the MCU pins are accessible on expansion connectors for further expansion13. 5Vin pinheader, 5V power supply is required when using USB HOST/OTG14. USB jumper- Short the jumper when using USB- Open the jumper to disconnect from I/O ports15. VBAT selection jumper- Short the jumper to use system power supply- Open the jumper to connect the VBAT to external power, such as battery16. VREF selection jumper- Short the jumper to connect VREF+/VREF- to VCC/GND- Open the jumper to connect VREF+/VREF- to other custom pin via jumper wirePackage Contents1. Core407V development board x 12. USB type A to Mini-B cable x 13. Software CD x 1

Read more less

About The ProtuctLD19 is mainly composed of laser ranging core, wireless transmission unit, wireless communication unit, angle measuring unit, motor driving unit, and mechanical housing.The LD19 ranging core adopts DTOF technology to measure 4500 times each second. When it works, LD19 emits the infrared laser forward, the laser is reflected to the single photon receiving unit after encountering the target object. Thus, we get both time of laser emitting and receiving, the gap between them is time of flight. With the light speed, we can calculate the distance.After receiving distance data, LD19 will combine them with angel value getting from angle measurement unit to comprise the points cloud data, then transmitting the points cloud data to external interface via wireless communication. Meanwhile, the external interface provides PWM to allow the motor driving unit to drive the motor. After the external control unit gets the rotational speed , it will reach to specified speed through PID algorithm closed-loop control to ensure LD19 work stably.Features1. Based on TOF (Time of Flight) laser ranging technology 2. Support UART communication 3. Measuring radius 12m 4. 30K Lux anti-glare interference 5. 4500Hz measurement frequency 6. 360 degree scanning range 7. Laser Safety Meets FDA Class 1 Standards 8. Compact appearance 9. 10000+ hours service lifeSpecifications1. Ranging Distance: 0.02 ~ 12.00 m 2. Ranging Average accuracy: +/-45 mm (within 0.3~12.00m) 3. Sweep Frequency: 5 ~ 13 Hz (Typ 10) 4. Scanning Angle: 360 degrees 5. Ranging Frequency: 4500 Hz 6. Resolution: 15mm 7. Wavelength: 895 ~ 915 nm (Typ 905) 8. Communication interface: UART 230400 9. Ambient Light Resistance: 30 KLux 10. Power Supply: 5V 11. Power Consumption: About 0.9W 12. Operating Current: 180mA 13. Operating Temperature: -10 degree C ~ 40 degree C 14. Lifetime: 10000+ hours 15. Dimensions: 54.00 x 46.29 x 34.80mm 16. Weight: 47gPackage List1. DTOF LIDAR LD19 x 1 2. Adapter x 1 3. USB cable 50cm x 1 4. 4 Pin cable 100mm x 1

Read more less

1. Good condition,with high quality ,great performance2. Cooling fan run smoothly, long life keep CPU safe without overheating3. Compatible with Raspberry Pi CM4 robotic projects and development boardsSpecification:1. Rated Power: 1W (5V, 0.2+/-0.02A); 1.62W (for 12V, 0.135+/-0.02A)2. Rated Speed: 5000+/-10%RPM( for 5V); 8000+/-10%RPM ( for 12V)3. General: Low-profile, PWM speed adjustment4. Interface: 4-wire PWM speed-adjustable fan header5. Cable length: 90+/-10mm6. Size: 54 x 39 x 13mmPackage List:1. CM4-FAN-3007 x 12. Screws and thermal tapes x 1

Read more less

1. Good condition,with high quality ,great performance2. Cooling fan run smoothly, long life keep CPU safe without overheating3. Compatible with Raspberry Pi CM4 robotic projects and development boardsSpecification:1. Rated Power: 1W (5V, 0.2+/-0.02A); 1.62W (for 12V, 0.135+/-0.02A)2. Rated Speed: 5000+/-10%RPM( for 5V); 8000+/-10%RPM ( for 12V)3. General: Low-profile, PWM speed adjustment4. Interface: 4-wire PWM speed-adjustable fan header5. Cable length: 90+/-10mm6. Size: 54 x 39 x 13mmPackage List:1. CM4-FAN-3007 x 12. Screws and thermal tapes x 1

Read more less

1. Universal: Low Profile, PWM Speed Adjustment 2. Interface: 4-wire PWM speed control fan connector 3. Rated speed: 8000+/-10%RPM 4. Rated power: 1.62W (12V, 0.135+/-0.02A) 5. Cable length: 125+/-10mm Package list: 1. CM4-FAN-3007-B x 1 2. Screws and thermal tapes x 1

Read more less

1. Dedicated all-In-one aluminum alloy cooling fan for Raspberry Pi 4B, PWM speed adjustment, better cooling, low noise, space saving2. This is a thin and lightweight heat sink, equipped with a 3510 ultra-quiet cooling fan, and the fan supports PWM speed regulation, which is perfectly compatible with Raspberry Pi OS. Other systems need to manually write python or C code to drive the fan speed through PWM.3. NOTE: Supports Raspberry Pi 4B Only, Automatic speed control function only supports Raspberry Pi OS.Specifications:1. Supported Pi: Raspberry Pi 4 Model B 1GB/2GB/4GB/8GB version2. Power supply: DC 5V input (can be powered by Raspberry Pi)3. Interface: 3-wire PWM speed control fan connector4. Rated power: 0.3W (5V, 0.6+/-0.02A)5. Cable length: 80+/-10mm6. Fan: 5500+/-10%RPMPackage List:1. PI4-FAN-PWM x12. Silicone thermal tape x4 and Screw x2

Read more less

1. Module Support: NVIDIA Jetson TX2 NX Module 2. Power supply: DC 5V input 3. Structure: Embedded fan, aluminum alloy shell 4. Electrical parameters: 0.65W (5V/0.13A) 5. Cable length: 37+/-3mm 6. Fan: PWM speed control, 5500+/-10%RPM

Read more less

Temperature-Humidity Sensor, DHT11 OnboardOverviewThis is a calibrated digital temperature and humidity module with onboard sensor DHT11. It can be used for detecting ambient temperature and humidity, through the standard single-wire interface.Specifications1. Temperature- Resolution : 1 degree C- Accuracy : +/-2 degree C- Measuring range : 0 degree C ~ 50 degree C2. Humidity- Resolution : 1%RH- Accuracy : +/-5%RH (0~50 degree C)- Measuring range : 20%RH ~ 90%RH (25 degree C)3. Operating voltage : 3.3V ~ 5.5 V4. Recommended storage condition- Temperature : 10 degree C ~40 degree C- Humidity : 60%RH or belowApplications1. Weather station2. Humidity controller3. Test & detection deviceHow to UseIn the case of working with a MCU:1. VCC: 3.3V ~ 5.5V2. GND: GND3. DOUT: MCU.IOPackage Contents1. DHT11 Temperature-Humidity Sensor x12. 3-pin custom connector jumper wire x1

Read more less

Overview1. This is a calibrated digital temperature and humidity module with onboard sensor DHT22 (AM2302), which features higher accuracy and wider measuring range than DHT11.2. It can be used for detecting ambient temperature and humidity, through the standard single-wire interface.Specifications1. Temperature- Resolution : 0.1degree C- Accuracy: +/-0.5 degree C- Measuring range: -40 degree C ~ 80 degree C2. Humidity- Resolution: 0.1%RH- Accuracy: +/-2%RH (25degree C)- Measuring range: 0%RH ~ 99.9%RH3. Operating voltage: 3.3V ~ 5.5 V4. Recommended storage condition- Temperature: 10 degree C ~40 degree C- Humidity: 60%RH or belowApplications1. Weather station2. Humidity controller3. Test & detection deviceHow to UseIn the case of working with a MCU:1. VCC: 3.3V ~ 5.5V2. GND: GND3. DOUT: MCU.IO

Read more less

1. Power supply: 9-24V2. Communication interface: RS485 port x 1, Ethernet port x 13. Baud rate: 300-115200 bps4. Data bits: 5-9 bits5. Configuration: host, web browser, device management function library6. Communication method: TCP/IP direct communication, VCOM7. Working temperature: -40 degrees to 85 degrees8. Main function: Bidirectional transparent data transmission between RS485 and Ethernet9. It is easy to combine multi-rail installed serial servers together, more freedom.10. It is suitable for Modbus grid upgrade and can be used in conjunction with 3D configuration software.11. Support TCP server / TCP client / UDP mode / UDP multicast.12. Multi-host rolling polling support, easy for cloud communication and device identification.

Read more less

Specifications1. CM4 Socket: Available on all variants of Compute Module 4 2. Network: Gigabit Ethernet RJ45 connector, 100M Ethernet RJ45 connector 3. USB: USB 2.0 Type A x 2 4. Connector: Isolated RS485 x 4, power screw terminal x 1 5. Camera: MIPI CSI-2 port x 2 (15pin 1.0mm FPC connector) 6. Video: HD-MI interface x 1, support 4K 30fps output 7. RTC: Real Time Clock with Battery Socket and Ability to Wake Compute Module 4 8. Storage: MicroSD card slot for Compute Module 4 Lite (no eMMC) variant 9. Fan head: allow speed adjustment, 5V 10. Indicator: Power indicator x 1, CM4 status indicator x 1, User LED x 2, RS485 communication indicator x 8 11. Power input: 7-36V 12. Dimensions: 123 x 98 x 32mmPackage List1. CM4-ETH-RS485-BASE-B x 1 2. Metal case (top and bottom) x 1 3. Fan x 1 4. 12V 2A Power Supply x 1 5. Screwdriver x 1 6. Antenna connector rubber plug x 1 7. Screws pack x 1

Read more less

Specifications1. CM4 Socket: Available on all variants of Compute Module 4 2. Network: Gigabit Ethernet RJ45 connector, 100M Ethernet RJ45 connector 3. USB: USB 2.0 Type A x 2 4. Connector: Isolated RS485 x 4, power screw terminal x 1 5. Camera: MIPI CSI-2 port x 2 (15pin 1.0mm FPC connector) 6. Video: HD-MI interface x 1, support 4K 30fps output 7. RTC: Real Time Clock with Battery Socket and Ability to Wake Compute Module 4 8. Storage: MicroSD card slot for Compute Module 4 Lite (no eMMC) variant 9. Fan head: allow speed adjustment, 5V 10. Indicator: Power indicator x 1, CM4 status indicator x 1, User LED x 2, RS485 communication indicator x 8 11. Power input: 7-36V 12. Dimensions: 123 x 98 x 32mmPackage List1. CM4-ETH-RS485-BASE-B x 1 2. Metal case (top and bottom) x 1 3. Fan x 1 4. 12V 2A Power Supply x 1 5. Screwdriver x 1 6. Antenna connector rubber plug x 1 7. Screws pack x 1

Read more less

1. CM4 socket: Suitable for all variants of Compute Module 4 2. Networking: Gigabit Ethernet RJ45 connector, 100M Ethernet RJ45 connector 3. Connetor: Isolated RS485 x 4, Power screw terminal x 1 4. USB: USB 2.0 Type A x 2 5. Cacmera: MIPI CSI-2 port x 2 (15pin 1.0mm FPC connector) 6. Video: HDMI port x 1, supports 4K 30fps output 7. RTC: Real-time clock with battery socket and ability to wake Compute Module 4 8. Storage: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 9. Fan header: Allows speed adjustment, 5V 10. Indicator: Power indicator x 1, CM4 status indicator x 1, User LED x 2, RS485 communication indicator x 8 11. Power input: 7-36V 12. Dimension: 93.6 x 108.8mm

Read more less

Specifications1. CM4 socket: Suitable for all variants of Compute Module 4 2. Network: - Ethernet: Dual Gigabit Ethernet RJ45 - M.2 B KEY, for connecting 5G / 4G module - Nano-SIM card slot, supports standard Nano-SIM card for 5G/4G/3G/2G communication 3. USB 3.2 Gen1 x 2 4. PIN header: Raspberry Pi 40PIN GPIO headerx 1 5. Display: MIPI DSI port (15pin 1.0mm FPC connector) 6. Camera: MIPI CSI-2 port x 2 (15pin 1.0mm FPC connector) 7. Video: HDMI x 2, supports 4K 30fps output 8. RTC: Real-time clock with battery socket and ability to wake Compute Module 4 9. Storage: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 10. Fan header: 5V/12V (12V by default), allows speed adjustment and measurement 11. Power input: 5V/2.5A 12. Size: 99.6 x 87.0mm

Read more less

1. CM4 Socket: Suitable for all variants of Compute Module 4 2. Networking: - Dual Gigabit Ethernet RJ45 - M.2 B KEY, for connecting 5G / 4G module - Nano-SIM card slot, supports standard Nano-SIM card for 5G/4G/3G/2G communication 3. USB: USB 3.2 Gen1 x 2 4. PIN header: Raspberry Pi 40PIN GPIO header 5. Display: MIPI DSI port (15pin 1.0mm FPC connector) 6. Camera: MIPI CSI-2 port x 2 (15pin 1.0mm FPC connector) 7. Video: HDMI x 2, supports 4K 30fps output 8. RTC: Real-time clock with battery socket and ability to wake Compute Module 4 9. Storage: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 10. FAN HEADER: 5V/12V (12V by default), allows speed adjustment and measurement 11. Power input: 5V/2.5A 12. Size: 99.6 x 87.0mm

Read more less

1. CM4 Socket: Suitable for all variants of Compute Module 4 2. Networking: - Dual Gigabit Ethernet RJ45 - M.2 B KEY, for connecting 5G / 4G module - Nano-SIM card slot, supports standard Nano-SIM card for 5G/4G/3G/2G communication 3. USB: USB 3.2 Gen1 x 2 4. PIN header: Raspberry Pi 40PIN GPIO header 5. Display: MIPI DSI port (15pin 1.0mm FPC connector) 6. Camera: MIPI CSI-2 port x 2 (15pin 1.0mm FPC connector) 7. Video: HDMI x 2, supports 4K 30fps output 8. RTC: Real-time clock with battery socket and ability to wake Compute Module 4 9. Storage: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 10. FAN HEADER: 5V/12V (12V by default), allows speed adjustment and measurement 11. Power input: 5V/2.5A 12. Size: 99.6 x 87.0mm

Read more less

Specification1. USB: USB 3.2 Gen1 x 3 2. GPIO: Raspberry Pi 40 PIN GPIO x 1 3. HD media interface: HDMI x 2, support 4K 30fps output 4. DSI display: MIPI DSI x 2 (15pin 1.0mm FPC) 5. CSI camera: MIPI CSI-2 x 2 (15pin 1.0mm FPC) 6. Power input: 7V - 36V 7. FAN: 5V / 12V (Allows speed adjustment and measurement) 8. RTC: Real-time clock with battery socket and ability to wake Compute Module 4 9. RJ45 Ethernet: Dual Gigabit Ethernet 10. CM4 slot: Suitable for all variants of Compute Module 4 11. SD card slot: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 12. Size:109.0 x 91.5mmPackage List1. CM4-DUAL-ETH-BASE x 1 2. Metal case (top and bottom) x 1 3. Fan-4010-PWM-12V x 1 4. Screwdriver x 1 5. Screws pack x 1 6. 12V 2A power adapter x 1

Read more less

Specification1. USB: USB 3.2 Gen1 x 3 2. GPIO: Raspberry Pi 40 PIN GPIO x 1 3. HD media interface: HDMI x 2, support 4K 30fps output 4. DSI display: MIPI DSI x 2 (15pin 1.0mm FPC) 5. CSI camera: MIPI CSI-2 x 2 (15pin 1.0mm FPC) 6. Power input: 7V - 36V 7. FAN: 5V / 12V (Allows speed adjustment and measurement) 8. RTC: Real-time clock with battery socket and ability to wake Compute Module 4 9. RJ45 Ethernet: Dual Gigabit Ethernet 10. CM4 slot: Suitable for all variants of Compute Module 4 11. SD card slot: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 12. Size:109.0 x 91.5mmPackage List1. CM4-DUAL-ETH-BASE x 1 2. Metal case (top and bottom) x 1 3. Fan-4010-PWM-12V x 1 4. Screwdriver x 1 5. Screws pack x 1 6. 12V 2A power adapter x 1

Read more less

Overview1. Sharp GP2Y1010AU0F onboard, detecting fine particle larger than 0.8μm in diameter, even like the cigarette smoke2. Low power consumption, analog voltage output, the output level is linear with dust density3. Embedded voltage boost circuit to support wide range of power supplySpecifications1. Sensitivity : 0.5V/(100ug/m3)2. Measurement range : 500ug/m33. Power : 2.5V~5.5V4. Operating current : 20mA(max)5. Operating temperature : -10~65 degree C6. Storage temperature : -20~80 degree C7. Life time : 5 years8. Dimension : 63.2mmx41.3mmx21.1mm9. Mounting holes size : 2.0mm10. Air hole size : 9.0mmApplications1. Air purifier2. Air conditioner3. Air monitor4. PM2.5 DetectorHow to UseIn the case of working with a MCU:1. VCC: 2.5V ~ 5.0V2. GND: GND3. AOUT: MCU.IO (analog output)4. ILED: MCU.IO (module driving pin)Package Contents1. Dust Sensor × 12. XH2.54 4-pin wire × 1

Read more less

Features1. This is an LTE Cat 6 Raspberry Pi communication HAT with GNSS and up to 300Mbps (downlink) / 50Mbps (uplink) data rate. It is applicable for countries/regions including Europe, the Middle East, Africa, Asia-Pacific, Brazil... By connecting it to PC, Raspberry Pi or Jetson Nano host boards, it is easy to enable LTE-A high speed networking, cloud platform communication, SMS, and global GNSS positioning functions. 2. Multi-constellation high-accuracy GNSS positioning: GPS, GLONASS, BeiDou/Compass, Galileo, QZSS 3. Integrates extensive network protocols, with multi drivers and software support, compatible with different OS including Windows / Linux / Android 4. USB 3.1 port (USB 2.0 compatible) for connecting to PC, Raspberry Pi, or Jetson Nano host board to enable high speed LTE-A communication 5. Standard M.2 B KEY slot, compatible with different core modules: EM06-E, EM06-J, EM06-A series 6. Onboard PWR and RST control pin, enabled via DIP switch, for connecting to external IO to turn on/off or reset the module 7. Onboard USB-C connector, enabled via switch, for connecting standalone power supply for the module, allows more loads, stable amd flexible power supply 8. Onboard power supply on/off switch, reset button and LED indicator, easy to turn on/off the module or monitor the operating status 9. Reserved 4x SMA to IPEX antenna interfaces, with pre-soldered 2x connectors for easily using antennas, allows changing the SMA antenna position 10. High efficiency power supply circuit, up to 3A output currentSpecificationsLTE CAT 6: 1. Region / Provider: EMEA / APAC (except Japan and CMCC) / Brazil 2. Module dimensions: 42.0 x 30.0 x 2.3 (mm) Temperature range: 1. Operating temperature: -30 degree C ~ +70 degree C 2. Extension temperature: -40 degree C ~ +85 degree C Frequency band 1. LTE-FDD: B1, B3, B5, B7, B8, B20, B28, B32 (receive only for B32) 2. LTE-TDD: B38, B40, B41 3. 2xCA: - B1+B1, B5, B8, B20, B28; - B3+B3, B5, B7, B8, B20, B28; - B7+B5, B7, B8, B20, B28; - B20+B32 (B32 is used for aux component carrier only), B38+B38, B40+B40, B41+B41 4. WCDMA: B1, B3, B5, B8 5. GNSS: GPS/GLONASS/BeiDou (Compass)/Galileo/QZSS Data rate: 1. LTE-FDD: 300 Mbps (DL) / 50 Mbps (UL) 2. LTE-TDD: 226 Mbps (DL) / 28 Mbps (UL) 3. DC-HSPA+: 42 Mbps (DL) / 5.76 Mbps (UL) 4. WCDMA: 384 Kbps (DL) / 384 Kbps (UL)Package List1. M.2 TO 4G/5G HAT x 1 2. EM06-E x 1 3. Antenna 2pcs x 1 4. IPEX adapter cable 2pcs x 1 5. 2*20PIN pin header x 1 6. Passive GPS antenna x 1 7. Dual plug USB3.0 cable x 1 8. USB3.0 adapter x 1 9. USB2.0 adapter x 1 10. SMA protective cap 2pcs x 1 11. Screws pack x 1

Read more less

Features1. OV2640 camera and digital microphone, supports applications like image recognition, voice processing... 2. Standard 40PIN GPIO header, compatible with Raspberry Pi HATs for sorts of IoT applications 3. Integrated Li-ion battery boost charging manager, supports battery charging/discharging, can also be powered from USB connection 4. Compatible with Arduino and ESP-IDF software SDK, seamlessly connecting with ESP-WHO applications 5. Onboard 8MB PSRAM, 4MB FLASH storage, supports SD extension as well 6. CP2102 USB to UART converter, for serial debugging/programming 7. 4x LED indicators, make it easy to check the operating status 8. Comes with development resources and manualSpecifications1. WIFI: 802.11b/g/n 2. BT: V4.2 including legacy BR/EDR and BLE low energy 3. Processor: Xtensa LX6 dual-core processor 240MHz 4. Camera: OV2640 (UXGA 1622 x 1200) 5. SRAM: 520KB+8MB 6. Flash: 448KB+4MB 7. Input voltage: 3.3V~5V 8. Working voltage: 3.3V 9. Charging current: 1A 5V 10. Overall consumption: 7.7mA 5V (ESP32 deep sleep) 11. Dimensions: 65mm x 30.5mm 12. Working temperature: -40 degree C ~ 85 degree CPackage List1. ESP32 One main unit x 1 2. USB-A to micro-B cable x 1 3. Screws pack x 1

Read more less

Features1. Allows controlling up to 253 SC, ST series serial bus servos at the same time (adequate power supply required) 2. Wide range voltage input 6-12V (the input voltage and the servo voltage must be matched) 3. Built-in WiFi and Bluetooth, as well as ESP-NOW support, for remote control and servo debugging 4. Automatic download circuit for easy uploading programs 5. Open source web application and various robot structures 6. Compact size and space saving, suitable for integration into sorts of space-limited projectsSpecifications1. Power supply voltage: DC 6-12V 2. Power Connector: 5.5 x 2.1mm DC 3. Download interface: Type-C 4. Controller: ESP32 5. Control interface: UART 6. Dimensions: 30 x 65mm 7. Mounting hole size: 2.75mm 8. Mounting hole spacing: 23 x 58mmPackage List1. Servo Driver with ESP32 x 1 2. Screws pack x 1

Read more less

1. Support development environment, such as ESP-IDF, Arduino, MicroPython, etc.2. 240MHz Xtensa 32-bit LX7 dual-core processor3. Easy to integrate, 32-bit LX7, 2MB PSRAM, wireless network, dual-core processor4. Using ESP32-S3R2 chip, Xtensa 32-bit LX7 dual-core processor, running frequency 240mhz5. Integrated 512KB SRAM, 384KB ROM, 2MB PSRAM, 16MB flash memory6. Integrated 2.4GHz Wi-Fi and Bluetooth LE dual-mode wireless communication, with excellent RF performance7. Type-C connector, more convenient to use8. The onboard CH343 and CH334 chips can meet the needs of USB and UART development through the Type-C interface9. Onboard DC-DC chip MP28164, high-efficiency DC-DC step-down boost chip, the load current can reach 2A10. 27 x multi-function GPIO pins, configurable pin functions, allowing flexible development and integration11. Abundant external interfaces, including full-speed USB OTG, SPI, I2C, UART, ADC, PWM and DVP (8-16-bit camera interface), LCD interface (8-16-bit parallel RGB, 18080, MOTO6800), etc., Flexible realization of various functions12. Castellated modules allow direct soldering to the carrier board13. Support a variety of low-power working states, adjustable communication distance, data rate and power consumption balance, to meet the power consumption requirements of various application scenarios14. Support the ecosystem of Raspberry Pi Pico expansion board, suitable for artificial intelligence loT application development15. Support ESP-IDF, Arduino, MicroPython comprehensive SDK, development resources, tutorials, help you get started easily16. ESP32-S3 is specially designed for AloT applications, using Xtensa 32-bit LX7 dual-core processor with a frequency up to 240 MHz, powerful aluminum computing capability and reliable security features17. WIFI and BLE 5 support, ESP32-S3 integrates 2.4 GHz Wi-Fi (802.11 B/G/N) and 40mhz bandwidth to support its Bluetooth low energy subsystem to support Bluetooth 5 (LE) and Bluetooth Mesh18. ESP32-S3: Xtensa 32-bit LX7 dual-core processor19. 2.4G monopole ceramic antenna20. W25Q128JVSIQ: 16MB Flash21. Start button: press to enter download mode when reset22. CH334F: USB HUB controller23. CH343P: USB to UART chip24. MP28164: High-efficiency DC-DC step-down boost chip25. Support more Pico expansion modules: Eval-Board, 3.5-inch LCD, 1.3-inch OLED, 8-segment LED, e-paper, NB-IoT module, GPIO expander, sensor module, RTC module, UPS module

Read more less

1. ESP32-S3-DEV-KIT-N8R8 is a microcontroller development board with a small size and a variety of digital interfaces.2. In terms of software, you can choose ESP-IDF, Arduino, MicroPython and other development environments for development, so that you can get started easily and quickly, and apply them to products.3. Using ESP32-S3-WROOM-1-N8R8 module, equipped with Xtensa 32-bit LX7 dual-core processor, the main frequency is up to 240MHz4. Integrated 512KB SRAM, 384KB ROM, 8MB PSRAM, 8MB Flash memory5. Integrated 2.4GHz Wi-Fi and Bluetooth Low Energy (Bluetooth LE) dual-mode wireless communication with superior RF performance6. Using the USB Type-C interface, no need to tangle with the front and back plugs7. The onboard CH343 and CH334 chips can meet the development and use requirements of USB and UART through a Type-C interface8. Lead out rich peripheral interfaces, pin compatible with ESP32-S3-DevKitC-1 development board, strong compatibility and expandability9. Stamp hole design, can be directly welded and integrated into the bottom plate designed by the user10. Support a variety of low-power working states, adjust the balance between communication distance, data rate and power consumption, and meet the power consumption requirements of various application scenarios

Read more less

1. ESP32-S3-DEV-KIT-N8R8 is a microcontroller development board with a small size and a variety of digital interfaces.2. In terms of software, you can choose ESP-IDF, Arduino, MicroPython and other development environments for development, so that you can get started easily and quickly, and apply them to products.3. Using ESP32-S3-WROOM-1-N8R8 module, equipped with Xtensa 32-bit LX7 dual-core processor, the main frequency is up to 240MHz4. Integrated 512KB SRAM, 384KB ROM, 8MB PSRAM, 8MB Flash memory5. Integrated 2.4GHz Wi-Fi and Bluetooth Low Energy (Bluetooth LE) dual-mode wireless communication with superior RF performance6. Using the USB Type-C interface, no need to tangle with the front and back plugs7. The onboard CH343 and CH334 chips can meet the development and use requirements of USB and UART through a Type-C interface8. Lead out rich peripheral interfaces, pin compatible with ESP32-S3-DevKitC-1 development board, strong compatibility and expandability9. Stamp hole design, can be directly welded and integrated into the bottom plate designed by the user10. Support a variety of low-power working states, adjust the balance between communication distance, data rate and power consumption, and meet the power consumption requirements of various application scenarios

Read more less

1. Support development environment, such as ESP-IDF, Arduino, MicroPython, etc.2. 240MHz Xtensa 32-bit LX7 dual-core processor3. Easy to integrate, 32-bit LX7, 2MB PSRAM, wireless network, dual-core processor4. Using ESP32-S3R2 chip, Xtensa 32-bit LX7 dual-core processor, running frequency 240mhz5. Integrated 512KB SRAM, 384KB ROM, 2MB PSRAM, 16MB flash memory6. Integrated 2.4GHz Wi-Fi and Bluetooth LE dual-mode wireless communication, with excellent RF performance7. Type-C connector, more convenient to use8. The onboard CH343 and CH334 chips can meet the needs of USB and UART development through the Type-C interface9. Onboard DC-DC chip MP28164, high-efficiency DC-DC step-down boost chip, the load current can reach 2A10. 27 x multi-function GPIO pins, configurable pin functions, allowing flexible development and integration11. Abundant external interfaces, including full-speed USB OTG, SPI, I2C, UART, ADC, PWM and DVP (8-16-bit camera interface), LCD interface (8-16-bit parallel RGB, 18080, MOTO6800), etc., Flexible realization of various functions12. Castellated modules allow direct soldering to the carrier board13. Support a variety of low-power working states, adjustable communication distance, data rate and power consumption balance, to meet the power consumption requirements of various application scenarios14. Support the ecosystem of Raspberry Pi Pico expansion board, suitable for artificial intelligence loT application development15. Support ESP-IDF, Arduino, MicroPython comprehensive SDK, development resources, tutorials, help you get started easily16. ESP32-S3 is specially designed for AloT applications, using Xtensa 32-bit LX7 dual-core processor with a frequency up to 240 MHz, powerful aluminum computing capability and reliable security features17. WIFI and BLE 5 support, ESP32-S3 integrates 2.4 GHz Wi-Fi (802.11 B/G/N) and 40mhz bandwidth to support its Bluetooth low energy subsystem to support Bluetooth 5 (LE) and Bluetooth Mesh18. ESP32-S3: Xtensa 32-bit LX7 dual-core processor19. 2.4G monopole ceramic antenna20. W25Q128JVSIQ: 16MB Flash21. Start button: press to enter download mode when reset22. CH334F: USB HUB controller23. CH343P: USB to UART chip24. MP28164: High-efficiency DC-DC step-down boost chip25. Support more Pico expansion modules: Eval-Board, 3.5-inch LCD, 1.3-inch OLED, 8-segment LED, e-paper, NB-IoT module, GPIO expander, sensor module, RTC module, UPS module

Read more less

1. Equipped with Xtensa® 32-bit LX7 dual-core processor, up to 240MHz main frequency2. Supports 2.4GHz Wi-Fi (802.11 b/g/n) and Bluetooth® 5 (LE)3. Built in 512KB of SRAM and 384KB ROM, onboard 4MB Flash memory and 2MB PSRAM4. Castellated module and onboard ceramic antenna, allows soldering direct to carrier boards5. Supports flexible clock, module power supply independent setting, and other controls to realize low power consumption in different scenarios6. Integrated with USB serial port full-speed controller, 34 × GPIO pins allows flexibly configuring pin functions7. 4 × SPI, 2 × I2C, 3 × UART, 2 × I2S, 2 × ADC, etc.8. Product size: 18 x 23.5mm9. Weight: 2g, 3g

Read more less

1. Equipped with Xtensa® 32-bit LX7 dual-core processor, up to 240MHz main frequency2. Supports 2.4GHz Wi-Fi (802.11 b/g/n) and Bluetooth® 5 (LE)3. Built in 512KB of SRAM and 384KB ROM, onboard 4MB Flash memory and 2MB PSRAM4. Castellated module and onboard ceramic antenna, allows soldering direct to carrier boards5. Supports flexible clock, module power supply independent setting, and other controls to realize low power consumption in different scenarios6. Integrated with USB serial port full-speed controller, 34 × GPIO pins allows flexibly configuring pin functions7. 4 × SPI, 2 × I2C, 3 × UART, 2 × I2S, 2 × ADC, etc.8. Product size: 18 x 23.5mm9. Weight: 2g, 3g

Read more less

1. Pixel: 96 x 48=4608 dots2. Pitch: 2.5mm3. Pixel format: 1R1G1B4. Viewing angle: greater than 140 degrees5. Control mode: synchronous6. Drive: 1/16 scan7. Connector: HUB758. Power supply: 5V / 2.5A (VH4 connector input)9. Power: within 20W10. Size: 24 x 12cmFeatures:1. 4608 independent RGB led, full color display, brightness adjustable2. 96x48 pixels, 2.5mm pitch, allows displaying text, color image or animation3. 240x120mm size, moderate size, suitable for DIY desktop display or wall mount display4. Two HUB75 headers on board, 1 for controller data input, 1 output, chain support5. Flexible PCB material, can be gently bent, suitable for some application scenarios such as cylinders, spheres and other curved surfaces6. Provide open source development resources (for Raspberry Pi / Raspberry Pi Pico / ESP32 / Arduino, etc.)

Read more less

1. Suitable for Raspberry Pi series boards2. Uses the IMX477R sensor, which is compact and offers 12.3 megapixels of high resolution and excellent low-light performance3. Uses M12 mount, requires M12 lens to work and can be integrated into industrial and commercial applications where higher visual fidelity is required4. Higher resolution, better imaging5. IR cut filter: integrated6. Lens support: M127. Output: RAW 12/10/8, COMP88. Back focus: Adjustable9. Size: 38x17.8x34.8mm

Read more less

Features 1. Official Raspberry Pi camera module 3 with high resolution and autofocus support, 12MP, adopts the IMX708 sensor and is compatible with Raspberry Pi series boards. 2. With better image quality and freer focus control performance. 3. 12MP High resolution: comes with IMX708 sensor, highly detailed, realistic Imaging 4. Flexible auto-focus: take photos smoothly without jamming, flexible and free 5. Working with for Raspberry Pi: direct connect to for Raspberry Pi different variants including 4B/3B+/3A+/3B/2B/B+/A+,extra FPC cable is required for Zero / Zero 2 W series Specifications 1. Pixels: 11.9MP (4608 × 2592) 2. Sensor: IMX708 3. Focusing: I2C controller with auto-focus support 4. CMOS size: 7.4mm 5. Aperture: F1.8 6. Focal lenth: 4.74mm 7. Field view: 75 degree 8. Devices support: Compatible with all Raspberry Pi motherboard models(Adapter cable is required to access Raspberry Pi Zero series motherboards)

Read more less

Features:1. The LC29H series can track L1+L5 dual-frequency and multi-GNSS signals, reducing multipath effects in urban canyons and improving positioning accuracy while maintaining low power consumption.2. Built-in LNA and SAW filters to achieve high sensitivity and strong anti-interference ability.3. Use dual-frequency positioning and RTK technology to meet centimeter-level high-precision positioning requirements.4. Suitable for real-time tracking systems and sharing economy applications, helping to develop applications such as drones, smart agricultural machinery, and shared two-wheelers.5. Standard Raspberry Pi 40PIN GPIO expansion header, supports Raspberry Pi series boards and Jetson Nano6. Supports simultaneous tracking of L1+L5 dual-frequency satellite signals, reducing the multipath effect in urban canyons and improving positioning accuracy.7. Supports concurrent reception of multiple GNSS systems (GPS, BDS, GLONASS, Galileo and QZSS) while maintaining low power consumption8. Built-in low-noise amplifier and acoustic surface filter to achieve -165dBm high sensitivity and enhanced anti-interference performance9. Supports multi-frequency active interference cancellation, effectively suppressing or eliminating narrowband signal (WiFi/2/3/4/5G) interference to ensure navigation accuracy10. A-GNSS (Assisted GNSS) support, reducing the cold start time to first fix (TTFF) at power-on to 5 seconds11. Support QGNSS software to facilitate setting various module functions12. Onboard battery holder, supports ML1220 rechargeable battery, used to save ephemeris information and hot start13. There are 4 LED indicators on the board to indicate the working status of the module.14. LC29H(AA) GPS HAT has the following features:-Support positioning enhancement systems (WAAS, EGNOS, MSAS and GAGAN) to improve positioning performance in service areas-Supports EASY technology to use stored ephemeris, almanac data and other information for positioning when there is no signal, improving positioning and first positioning time15. LC29H(DA) GPS/RTK HAT has the following features:-Supports fast convergence dual-frequency RTK centimeter-level positioning, suitable for high-precision positioning of terminal equipment16. LC29H(BS) GPS/RTK HAT has the following features:-Supports GNSS original observation and correction data output, suitable for establishing RTK base stationsProduct parameters:1. Frequency bandGPS/QZSS: L1C/A, L5Beidou system: B1I, B2aGalileo: E1, E5aGLONASS: L12. Number of concurrent GNSSGPS/QZSS+Beidou+Galileo+GLONASS3. SensitivityTracking navigation: -165dBmReacquisition: -159dBm, -157dBm, -159dBmCold start: -147dBm, -145dBm, -147dBm4. Dynamic performanceAcceleration (maximum): 4gAltitude (maximum): 10000mSpeed (maximum): 500m/s5. Communication interfaceUART (9600~3000000bps, default 115200bps), I2C (maximum 400KHz)6. Protocol: NMEA 0183 V4.10, RTCM 3.x7. Power supply: 5V8. Total current: less than 40mA@5V (continuous mode)9. Operating temperature: -40 to 85 degrees Celsius10. Product size: 65 x 30.5mm11. Weight: 126gPacking list:-LC29H GPS hat x 1-2x20PIN female socket x 1-GPS external antenna (D) x 1-IPEX 1 to SMA cable 17cm x 1-Screw pack x1

Read more less

Features:1. The LC29H series can track L1+L5 dual-frequency and multi-GNSS signals, reducing multipath effects in urban canyons and improving positioning accuracy while maintaining low power consumption.2. Built-in LNA and SAW filters to achieve high sensitivity and strong anti-interference ability.3. Use dual-frequency positioning and RTK technology to meet centimeter-level high-precision positioning requirements.4. Suitable for real-time tracking systems and sharing economy applications, helping to develop applications such as drones, smart agricultural machinery, and shared two-wheelers.5. Standard Raspberry Pi 40PIN GPIO expansion header, supports Raspberry Pi series boards and Jetson Nano6. Supports simultaneous tracking of L1+L5 dual-frequency satellite signals, reducing the multipath effect in urban canyons and improving positioning accuracy.7. Supports concurrent reception of multiple GNSS systems (GPS, BDS, GLONASS, Galileo and QZSS) while maintaining low power consumption8. Built-in low-noise amplifier and acoustic surface filter to achieve -165dBm high sensitivity and enhanced anti-interference performance9. Supports multi-frequency active interference cancellation, effectively suppressing or eliminating narrowband signal (WiFi/2/3/4/5G) interference to ensure navigation accuracy10. A-GNSS (Assisted GNSS) support, reducing the cold start time to first fix (TTFF) at power-on to 5 seconds11. Support QGNSS software to facilitate setting various module functions12. Onboard battery holder, supports ML1220 rechargeable battery, used to save ephemeris information and hot start13. There are 4 LED indicators on the board to indicate the working status of the module.14. LC29H(AA) GPS HAT has the following features:-Support positioning enhancement systems (WAAS, EGNOS, MSAS and GAGAN) to improve positioning performance in service areas-Supports EASY technology to use stored ephemeris, almanac data and other information for positioning when there is no signal, improving positioning and first positioning time15. LC29H(DA) GPS/RTK HAT has the following features:-Supports fast convergence dual-frequency RTK centimeter-level positioning, suitable for high-precision positioning of terminal equipment16. LC29H(BS) GPS/RTK HAT has the following features:-Supports GNSS original observation and correction data output, suitable for establishing RTK base stationsProduct parameters:1. Frequency bandGPS/QZSS: L1C/A, L5Beidou system: B1I, B2aGalileo: E1, E5aGLONASS: L12. Number of concurrent GNSSGPS/QZSS+Beidou+Galileo+GLONASS3. SensitivityTracking navigation: -165dBmReacquisition: -159dBm, -157dBm, -159dBmCold start: -147dBm, -145dBm, -147dBm4. Dynamic performanceAcceleration (maximum): 4gAltitude (maximum): 10000mSpeed (maximum): 500m/s5. Communication interfaceUART (9600~3000000bps, default 115200bps), I2C (maximum 400KHz)6. Protocol: NMEA 0183 V4.10, RTCM 3.x7. Power supply: 5V8. Total current: less than 40mA@5V (continuous mode)9. Operating temperature: -40 to 85 degrees Celsius10. Product size: 65 x 30.5mm11. Weight: 126gPacking list:-LC29H GPS hat x 1-2x20PIN female socket x 1-GPS external antenna (D) x 1-IPEX 1 to SMA cable 17cm x 1-Screw pack x1

Read more less

Features:1. The LC29H series can track L1+L5 dual-frequency and multi-GNSS signals, reducing multipath effects in urban canyons and improving positioning accuracy while maintaining low power consumption.2. Built-in LNA and SAW filters to achieve high sensitivity and strong anti-interference ability.3. Use dual-frequency positioning and RTK technology to meet centimeter-level high-precision positioning requirements.4. Suitable for real-time tracking systems and sharing economy applications, helping to develop applications such as drones, smart agricultural machinery, and shared two-wheelers.5. Standard Raspberry Pi 40PIN GPIO expansion header, supports Raspberry Pi series boards and Jetson Nano6. Supports simultaneous tracking of L1+L5 dual-frequency satellite signals, reducing the multipath effect in urban canyons and improving positioning accuracy.7. Supports concurrent reception of multiple GNSS systems (GPS, BDS, GLONASS, Galileo and QZSS) while maintaining low power consumption8. Built-in low-noise amplifier and acoustic surface filter to achieve -165dBm high sensitivity and enhanced anti-interference performance9. Supports multi-frequency active interference cancellation, effectively suppressing or eliminating narrowband signal (WiFi/2/3/4/5G) interference to ensure navigation accuracy10. A-GNSS (Assisted GNSS) support, reducing the cold start time to first fix (TTFF) at power-on to 5 seconds11. Support QGNSS software to facilitate setting various module functions12. Onboard battery holder, supports ML1220 rechargeable battery, used to save ephemeris information and hot start13. There are 4 LED indicators on the board to indicate the working status of the module.14. LC29H(AA) GPS HAT has the following features:-Support positioning enhancement systems (WAAS, EGNOS, MSAS and GAGAN) to improve positioning performance in service areas-Supports EASY technology to use stored ephemeris, almanac data and other information for positioning when there is no signal, improving positioning and first positioning time15. LC29H(DA) GPS/RTK HAT has the following features:-Supports fast convergence dual-frequency RTK centimeter-level positioning, suitable for high-precision positioning of terminal equipment16. LC29H(BS) GPS/RTK HAT has the following features:-Supports GNSS original observation and correction data output, suitable for establishing RTK base stationsProduct parameters:1. Frequency bandGPS/QZSS: L1C/A, L5Beidou system: B1I, B2aGalileo: E1, E5aGLONASS: L12. Number of concurrent GNSSGPS/QZSS+Beidou+Galileo+GLONASS3. SensitivityTracking navigation: -165dBmReacquisition: -159dBm, -157dBm, -159dBmCold start: -147dBm, -145dBm, -147dBm4. Dynamic performanceAcceleration (maximum): 4gAltitude (maximum): 10000mSpeed (maximum): 500m/s5. Communication interfaceUART (9600~3000000bps, default 115200bps), I2C (maximum 400KHz)6. Protocol: NMEA 0183 V4.10, RTCM 3.x7. Power supply: 5V8. Total current: less than 40mA@5V (continuous mode)9. Operating temperature: -40 to 85 degrees Celsius10. Product size: 65 x 30.5mm11. Weight: 126gPacking list:-LC29H GPS hat x 1-2x20PIN female socket x 1-GPS external antenna (D) x 1-IPEX 1 to SMA cable 17cm x 1-Screw pack x1

Read more less

1. Suitable for Raspberry Pi Pico and other devices to achieve reliable remote communication2. Standard Raspberry Pi Pico header supports Raspberry Pi Pico series boards.3. Features CAN function, adopts SPL interface CAN controller MCP2515 with transceiver SIT65HVD230DR4. Comes with online development resources and manual (Raspberry Pi Pico C/C++ and MicroPvthon examples)l5. Operating voltage: 3.3V-5V6. CAN controller: RMCP25157. CAN transceiver: SIT65HVD230DR8. Communication bus: SPI9. Baudrate: 5K-1000Kbps10. Size: 52 x 21mm

Read more less

1. Official Raspberry Pi hardware debugging toolkit designed for Pico2. Built with RP2040 microcontroller chip designed by for Raspberry Pi3. Integrated design, with solder-free, plug-and-play features, can be connected to the debugging interface of the target board through the SWD interface4. RP2040 microcontroller chip designed by British for Raspberry Pi5. Onboard Micro-USB interface, used to connect to PC or other motherboards6. Onboard 3PIN SWD interface, used to connect the target board7. Onboard 3PIN USB to UART bridge standard CMSIS-DAP interface, compatible with most arm microcontrollers8. Using OpenOCD and other tools that support CMSIS-DAP9. Follow the Raspberry Pi 3PIN debug connector specification10. Comes with transparent plastic case and connecting cable11. Open source program, more convenient for firmware upgrade12. Size: 22x32mm

Read more less

Features1. Adopt original FT232RNL chip, fast communicating, stable and reliable, better compatibility2. Supports multiple communication interface conversion: USB to RS232, USB to RS485, USB to RS422, USB to TTL3. Onboard unibody power supply isolation, provides stable isolated voltage, needs no extra power supply for the isolated terminal4. Onboard unibody digital isolation, allows signal isolation, high reliability, strong anti-interference, low power consumption5. Onboard TVS (Transient Voltage Suppressor), effectively suppress surge voltage and transient spike voltage in the circuit, lightningproof & ESD protection6. Onboard self-recovery fuse and protection diodes, ensures the current/voltage stable outputs, provides over-current/over-voltage proof, improves shock resistance7. Fully automatic transceiver circuit with no delay, ensures the USB port communicates with different interfaces fastly and stably, without interfering with each other8. Onboard TTL serial 3.3V/5V voltage translator, config the TTL level via switch9. 3 LEDs for indicating the power and transceiver status10. High quality USB-B and RS232 connectors, smoothly plug/pull11. Industrial grade metal case, supports wall-mount and rail-mount installations, solid and beautiful, easy to installSpecifications1. Product type: Industrial grade digital isolated converter2. Operating system: for Mac, Linux, Android, Windows 11 / 10 / 8.1 / 8 / 73. Operating temperature: -15℃ ~ 70℃4. Device port: RS232/485/422/TTL5. Host port: USB6. USB:- Operating voltage: 5V- Connector: USB-B- Protection: 200mA self-recovery fuse, isolated output7. RS232:- Connector: DB9 male- Protection: TVS diode, surge protection & ESD protection- Transmission mode: Point-to-point- Baud rate: 300bps ~ 3Mbps8. RS485/422:- Connector: Screw terminal- Direction control: Hardware automatic control- Protection: 600W lightningproof and surge-suppress, 15KV ESD protection (reserved two 120R balancing resistors, enabled/disabled via jumper)- Transmission mode: Point-to-multipoints (485 mode: up to 32 nodes, it is recommended to use repeaters for 16 nodes or more； 422 mode: up to 256 nodes, it is recommended to use repeaters for 16 nodes or more)- Baud rate: 300bps ~ 3Mbps9. TTL (UART):- Connector: Screw terminal- Pins: TXD, RXD, GND, 5V/3.3V- Protection: Clamp protection diode, over-voltage/negative-voltage proof, shock resistance- Transmission mode: Point-to-point- Baud rate: 300bps ~ 3Mbps10. Indicators:- PWR: Red power indicator, light up when there is USB connection and voltage is detected- TXD: TX indicator, light up when the USB port sends data- RXD: RX indicator, light up when the device ports send data back11. Package contents:- USB TO RS232/485/TTL x1- USB cable x1

Read more less

OverviewThis little module adds arcade controls to your micro:bit, makes it possible to turn the micro:bit into a mini game console. There's onboard buzzer to play music and game background effect. It is powered from a 14500 Li-ion battery (not included), conversely, it allows to charge the battery through USB connection.Features1. micro:bit edge connector, directly pluggable2. High quality joystick, dual channel analog outputs for precise positioning, one channel digital output for press control3. Onboard battery and charge circuitry, powered from battery, also charges the battery through USB connection4. Battery indicator, blinks 1/2/3/4 times indicates the power remains about 25%/50%/75%/100% respectively5. 4x colorful buttons6. 2x side buttons, related to the A/B buttons of micro:bit, easy to use7. Buzzer for playing music and game background effect8. Comes with development resources (micro:bit graphical demo/python code/user manual, etc.)Specifications1. Operating voltage: 5V2. Battery type: 14500 Li-ion3. Dimension: 150mm x 50mm

Read more less

1.5 inch RGB OLED display module, 128x128 pixels, 16-bit high color, SPI interfaceOverviewThis is a general RGB OLED display Module, 1.5inch diagonal, 128x128 pixels, 16-bit high color (65K colors), with embedded controller, communicating via SPI interface.Features1. 128x128 high resolution, 65K colors, clearly displays colorful images2. Support 4-wire SPI OR 3-wire SPI interface, configured via onboard resistor3. Come with development resources and manual (examples for Raspberry Pi/Arduino/STM32)Specifications1. Driver: SSD13512. Interface: 4-wire SPI, 3-wire SPI3. Display color: RGB, 65K colors4. Resolution: 128x1285. Viewing angle: >160 degree6. Operating voltage: 3.3V / 5V7. Dimension: 44.5 x 37 (mm)Package Contents1. 1.5 inch RGB OLED Module x12. PH2.0 7Pin x1

Read more less

1.5inch OLED display Module, 128x128 pixels, 16 gray scale, SPI/I2C interfaceOverviewThis is a general OLED display Module, 1.5inch diagonal, 128x128 pixels, 16 gray scale, with embedded controller, communicating via SPI or I2C interface.Features1. 128x128 high resolution2. 16 gray scale, better display effect3. Support SPI or I2C interface, configured via onboard resistor4. Come with development resources and manual (examples for Raspberry Pi/Arduino/STM32)Specifications1. Driver: SSD13272. Interface: SPI / I2C3. Display color: White4. Gray scale: 165. Resolution: 128x128 (most other competitive products are typically 128x64)6. Viewing angle: >160 degree7. Operating voltage: 3.3V / 5V8. Dimension: 44.5 x 37 (mm)Package Contents1. 1.5 inch OLED Module x12. PH2.0 7Pin x1

Read more less

1. 2.8 inch IPS screen, 640 x 480 pixels, 70% NTSC color gamut.2. Enjoys a smooth gaming experience with 60fps.3. Optical bonding toughened glass panel with anti-fingerprint technique.4. Compatible with Raspberry Pi Zero 2 W.5. Battery indicator light for checking the power of the game console easily.6. Update ROMs via WiFi.Specifications:1. Controller:- Raspberry Pi Zero 2 W-- BCM2710A1 quad-core 64-bit SoC (Arm Cortex-A53 @1GHz)-- 512MB LPDDR2 SDRAM-- 2.4GHz IEEE 802.11b/g/n Wireless LAN, Bluetooth 4.2, BLE2. Display:- 2.8 inch IPS Screen-- 640 x 480 pixels-- Fully laminated toughened glass panel, anti-fingerprint technique-- 70% NTSC color gamut3. Battery: 1500 mAh4. Storage: 32G TF card5. Size: 136.4 x 67.5mmPackage List:1. GPM280 main unit x12. Assembled, with Raspberry Pi Zero 2 W and 32GB TF card3. Screwdriver x14. Power adapter 5V 3A x15. Card reader x16. Cleaning cloth x1

Read more less

1. 2.8 inch IPS screen, 640 x 480 pixels, 70% NTSC color gamut.2. Enjoys a smooth gaming experience with 60fps.3. Optical bonding toughened glass panel with anti-fingerprint technique.4. Compatible with Raspberry Pi Zero 2 W.5. Battery indicator light for checking the power of the game console easily.6. Update ROMs via WiFi.Specifications:1. Controller:- Raspberry Pi Zero 2 W-- BCM2710A1 quad-core 64-bit SoC (Arm Cortex-A53 @1GHz)-- 512MB LPDDR2 SDRAM-- 2.4GHz IEEE 802.11b/g/n Wireless LAN, Bluetooth 4.2, BLE2. Display:- 2.8 inch IPS Screen-- 640 x 480 pixels-- Fully laminated toughened glass panel, anti-fingerprint technique-- 70% NTSC color gamut3. Battery: 1500 mAh4. Storage: 32G TF card5. Size: 136.4 x 67.5mmPackage List:1. GPM280 main unit x12. Assembled, with Raspberry Pi Zero 2 W and 32GB TF card3. Screwdriver x14. Power adapter 5V 3A x15. Card reader x16. Cleaning cloth x1

Read more less

GSM/GPRS/GNSS/Bluetooth HAT for Raspberry Pi, Based on SIM868Overview1. This is a handy, low power Raspberry Pi HAT which features multi communication functionalities: GSM, GPRS, GNSS and Bluetooth.2. It allows your Pi to easily make a telephone call, send messages, connect to wireless Internet, global position, transfer data via Bluetooth, and so on.Features1. Raspberry Pi connectivity, compatible with Raspberry Pi 2B/3B/3B+/Zero/Zero W2. Support SMS, phone call, GPRS, DTMF, HTTP, FTP, MMS, email, etc.3. Support GPS, COMPASS, Glonass, LBS base station positioning, omni-positioning4. Bluetooth 3.0, supports data transferring through Bluetooth5. Onboard USB TO UART converter CP2102 for UART debugging6. 6x LEDs for indicating the module working status7. SIM card slot for 1.8V/3V SIM card8. RTC with backup battery holder9. Baudrate auto detection (1200bps ~115200bps)10. Control via AT commands (3GPP TS 27.007, 27.005, and SIMCOM enhanced AT Commands)11. Support SIM application toolkit: GSM 11.14 Release 9912. Come with development resources and manual (examples for Raspberry Pi/Arduino/STM32)GSM/GPRS1. Band- GSM 850/EGSM 900/DCS 1800/PCS 1900 MHz- Quad-band auto search- Compliant to GSM phase 2/2+2. Emitting power- Class 4 (2W @ GSM 850/EGSM 900 MHz)- Class 1 (1W @ DCS 1800/PCS 1900 MHz)4. GPRS connectivity- GPRS multi-slot class 12 (default)- GPRS multi-slot class 1~12 (configurable)5. GPRS data feature- Downlink speed: max 85.6kbps- Uplink speed: max 85.6kbps- Coding schemes: CS-1\CS-2\CS-3\CS-4- Support PAP (Password Authentication Protocol) for PPP connection- Support PBCCH- Support USSD6. SMS- Support: MT/MO/CB/Text/PDU mode- SMS storage: SIM card7. Audio- Voice encode/decode mode: Half Rate\Full Rate\Enhanced Full Rate\Adaptive muti rate- Support echo cancellation- Support noise reductionGNSS1. Receiver type- 33 tracking channels- 99 acquisition channels- GPS L1 C/A code2. Sensitivity- Tracking: -165 dBm- Cold starts: -148 dBm3. Time-To-First-Fix- Cold starts: 28s (typ.)- Hot starts: < 1s- Warm starts: 26s4. Accuracy- Horizontal position: <2.5m CEPBluetooth1. Integrates AT commands2. Compliant to Bluetooth specification3.0 + EDR3. Support SPP, OPP, HFP/HSP, etc.Misc1. Operating voltage: 5V2. Operating temperature: -40 degree C ~ 85 degree C3. Storage temperature: -45 degree C ~ 90 degree C4. Dimensions: 30.2mm x 65mmWhat is on Board1. SIM868 module2. ZMM5V1: Regulator diode3. SMF05C: TVS diode4. CP2102: USB TO UART converter5. MP1482: Power chip6. NDC7002N: Voltage level translator7. GPS status indicator8. NET indicator:- Flashes fast when the module starts up- Flashes slowly after GSM register succeed9. STA module working status indicator10. SIM868 UART Tx/Rx indicator11. Power indicator12. SIM868 control button: press the button and hold for 1s, to startup/shutdown the SIM86813 .Raspberry Pi GPIO connector14. SIM card slot15. USB TO UART interface16. 3.5mm earphone/mic jack17. GNSS antenna connector18. Bluetooth antenna connector19. GSM antenna connector20. CR1220 battery holder: for RTC backup battery21. UART selection switch- A: Control the SIM868 through USB TO UART- B: Control the SIM868 through Raspberry Pi- C: Access Raspberry Pi through USB TO UARTPackage Contents1. GSM/GPRS/GNSS HAT x12. GSM Antenna x13. GPS External Antenna (B) x14. Bluetooth Antenna x15. USB type A plug to micro plug cable x16. RPi screws pack (2pcs) x1

Read more less