Electronics Modules

1. RP2040 microcontroller chip designed by Raspberry Pi in the United Kingdom 2. Dual-core Arm Cortex M0+ processor, flexible clock running up to 133 MHz 3. 264KB of SRAM, and 2MB of on-board Flash memory 4. USB-C connector, keeps it up to date, easier to use 5. Castellated module allows soldering direct to carrier boards 6. USB 1.1 with device and host support 7. Low-power sleep and dormant modes 8. Drag-and-drop programming using mass storage over USB 9. 29 x multi-function GPIO pins (20 x via edge pinout, others via solder points) 10. 2 x SPI, 2 x I2C, 2 x UART, 4 x 12-bit ADC, 16 x controllable PWM channels 11. Accurate clock and timer on-chip 12. Temperature sensor 13. Accelerated floating-point libraries on-chip 14. 8 x Programmable I/O (PIO) state machines for custom peripheral support

Read more less

About The ProductThe Core1262-868M is a LoRa core module which incorporates new-generation SX1262 chip. It has featuress including mini size, long range transmission, high anti-interference capability, and so on. The module uses EU868 band, combined with LoRa gateway, it can be connected to servers like TTN server to build LoRa network. 1. New-generation SX1262, higher power efficiency and longer transmission distance than the traditional SX1278 2. EU868 band, combined with LoRa gateway, quick connection to cloud servers like TTN server 3. Comes with rich development resources and manual (examples for STM32, Raspberry Pi Pico)Specifications1. RF chip: SX1262 2. Frequency range: EU868 (863~870MHz) 3. Modulation: LoRa/(G)FSK 4. Data rate: 0.018~62.5Kbps (LoRa), 0.6~300Kbps ((G)FSK) 5. Emit power: More than 14dBm 3.3V 6. Spreadind factor: SF5 ~ SF12 7. Operating voltage: 3.3V 8. Module power consumption: Emitting current: 45mA 14dBm; receiving current: 5.3mA 125KHz 9. Communication bus: SPI 10. Operating temperature: -40 ~ 85 degree C 11. Connector: Castellated edge / solder holes 12. Dimensions: 21.00 x 52.00mm

Read more less

About The ProtuctThis is an industrial expansion module based on Raspberry Pi CM4, which features common interfaces such as Gigabit Ethernet, HDMI, USB, and GPIO, allows additional 4G / 5G / LoRa wireless communication modules to be connected via the M.2 or Mini-PCIe socket. There are also industrial interfaces/resources including RS485, CAN, and RTC. Combined with the industrial rail-mount protection case, the module is an ideal choice for building IoT gateway, 4G/5G router, IoT data acquisition, or even the PLC device in industrial automatic control system, and more.Specifications1. CM4 socket: For all variants of Compute Module 4 2. Networking: - Gigabit Ethernet RJ45 - M.2 B KEY / Mini-PCIe (via adapter), for connecting 5G / 4G / LoRa wireless module - Nano-SIM card slot, support standard Nano-SIM card for 5G/4G/3G/2G communication 3. USB: USB 2.0 x 3 4. PIN header: Non-isolated RS485 x 2, non-isolated CAN x 1, some GPIO pins 5. Camera: MIPI CSI-2 x 1 (15pin 1.0mm FPC connector) 6. Video: HDMI x 1, support 4K 30fps output 7. RTC: Real-time clock with battery socket and ability to wake Compute Module 4 8. Storage: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 9. Fan header: 5V/12V, allows speed adjustment and measurement 10. Power input: 5V or 7~36V 11. Dimensions: 145 x 90 x 40mmPackage List1. CM4-IO-WIRELESS-BASE x 1 2. PCIe to 4G/LoRa adapter x 1 3. Screwdriver x 1 4. Screws pack x 1 5. 12V 2A power adapter x 1

Read more less

About The ProtuctThis is an industrial expansion module based on Raspberry Pi CM4, which features common interfaces such as Gigabit Ethernet, HDMI, USB, and GPIO, allows additional 4G / 5G / LoRa wireless communication modules to be connected via the M.2 or Mini-PCIe socket. There are also industrial interfaces/resources including RS485, CAN, and RTC. Combined with the industrial rail-mount protection case, the module is an ideal choice for building IoT gateway, 4G/5G router, IoT data acquisition, or even the PLC device in industrial automatic control system, and more.Specifications1. CM4 socket: For all variants of Compute Module 4 2. Networking: - Gigabit Ethernet RJ45 - M.2 B KEY / Mini-PCIe (via adapter), for connecting 5G / 4G / LoRa wireless module - Nano-SIM card slot, support standard Nano-SIM card for 5G/4G/3G/2G communication 3. USB: USB 2.0 x 3 4. PIN header: Non-isolated RS485 x 2, non-isolated CAN x 1, some GPIO pins 5. Camera: MIPI CSI-2 x 1 (15pin 1.0mm FPC connector) 6. Video: HDMI x 1, support 4K 30fps output 7. RTC: Real-time clock with battery socket and ability to wake Compute Module 4 8. Storage: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 9. Fan header: 5V/12V, allows speed adjustment and measurement 10. Power input: 5V or 7~36V 11. Dimensions: 145 x 90 x 40mmPackage List1. CM4-IO-WIRELESS-BASE x 1 2. PCIe to 4G/LoRa adapter x 1 3. Screwdriver x 1 4. Screws pack x 1 5. 12V 2A power adapter x 1

Read more less

1. Three-in-one electronic clock module, integrating three practical functions: time, thermometer and voltmeter2. Using RX8025T clock chip, the timing accuracy is stable3. The lengthened temperature probe can effectively solve the problem that the temperature affected by the module temperature is not accurate enough4. Power supply voltage: DC5.0-30V5. Temperature function range: -40-120 degrees Celsius, resolution 0.16. Voltmeter function range: DC5-30V (requires pure DC power supply, it is not recommended to use 24V battery, because the voltage may be too high during charging and burn)7. Size: about 4x1.4x1.3cmFunction and usage instructions:1. Adjust time, date, year, voltage error, temperature error cycle display item definition, alternate display interval time2. In the non-setting state, press the left key to enter the time adjustment (note that the colon in the middle is bright):- At this time, the minute bar starts to flash, press the right button to increase, the adjustment range is 00-59, after adjusting, press the left button again, the hour bar starts to flash, press the right button to increase, the adjustment range is 00-23- After adjusting the hour, press the left button again to enter the date adjustment (note that the colon in the middle is off), at this time the date column starts to flash, press the right button to increase, the adjustment range is 1-31, after the date is adjusted, press the left button again key, the month column starts to flash, press the right key to increase, the adjustment range is 1-12, after adjusting the date, press the left key again, the year column starts to flash, press the right key to increase, the adjustment range is 2012-2049- After adjusting the year, press the left key again to enter the error calibration function of the displayed voltage, the unit is 0.1V, a positive number means increase, and a negative number means decrease- Then press the left key again to enter the temperature error calibration setting, press the right key to increase, a positive number means increase, a negative number means decrease, the unit is Celsius- Press the left button again to enter the definition function dd option of the display item in the cycle display state,Press the right button to change the value: (dd:0) time + temperature + voltage, (dd: 1) time + temperature, (dd: 3) time + voltage- Press the left button again to enter the cycle display alternate interval time dF option, press the right button to change the value, the larger the value, the longer the interval- Press the left button again to save all the set values ??and return to the normal display state3. Switch display items: in the non-setting state, press the right key to switch the display items, and the display will switch between the time-date-temperature-voltage alternate display

Read more less

1. Both 6-60V batteries and lithium batteries can be used2. LCD display, battery voltage, charging percentage and charging time at a glance3. Powerful functions, can automatically charge control, can control the charging time, can set and upload the corresponding parameters through the serial port4. Control voltage: DC6-60V5. Control current: within 10A6. Output type: direct output of various accumulators, lithium batteries7. Appearance size: about 7.9x4.2 cm8. Weight: about 30 gramsFunction Description:1. Automatic charging control function: by setting the upper limit voltage UP and lower limit voltage dn; when the battery voltage is less than or equal to the lower limit voltage dn, the relay is turned on, and the charger starts to charge the battery; when the battery voltage is greater than or equal to the upper limit voltage UP, the relay is turned off, Complete an automatic charge2. Charging time control function3. Serial data upload and parameter setting function: The system supports UART data upload and parameter setting function (TTL level)parameter settings:1. Press and hold the SET button to enter the parameter setting interface, the LCD will display SET2. After entering the parameter setting interface, short press the SET key to switch the set parameters3. After selecting the parameter, you can set it through the UP/DOWN key, support short press, long press (rapid increase or decrease)4. To set other parameters, repeat steps 2/35. After all parameter settings are completed, long press the SET button to exit and saveButton function description:In the running interface (main interface):1. Short press the SET button to display the currently set parameters2. Short press the UP button to switch to display the charging percentage and charging time3. Short press the DOWN button to select on/off the relay enable. If the relay enable is turned off, OFF will be displayed as a reminder and the relay is disconnected.4. Press and hold the UP button to set the status of the LCD backlight (L-P), the OFF backlight is always on, and the ON backlight will automatically turn off after 5-10 minutes5. Long press the SET button to enter the parameter settingAdditional features:1. Charging time recording function: When the charging time control is not turned on, the product will record a complete time. When entering the time display interface, the charging time will flash and display, and then exit the time display interface or clear it when the next charging is turned on (the relay is turned on).2. Parameter automatic detection: after setting the parameters and exiting, if the lower voltage limit dn is greater than or equal to the upper limit voltage up, the system will flash ERR as a reminder3. Battery connection detection: this product is attached to the battery, if the battery is not connected, the system will display nbE in the lower line as a reminder

Read more less

1. Input voltage: 6.5-36V (the input voltage is lower than 6.5V, the current accuracy is inaccurate, and the LCD display is abnormal if it is lower than 5.5V)2. Output voltage: 1.2-32V, the default output is 5V step-down type, the output voltage can only be lower than the input voltage, and the voltage difference is more than 2V3. Output current: It can work stably at 3.5A for a long time, and it can reach about 4.5A with fan enhanced heat dissipation (adjustable limit current can reach about 4.2-4.5A)4. Output power: natural heat dissipation 50W (within 3.5A), plus fan to enhance heat dissipation 75W5. Voltage display: resolution 0.05V, range 1.2-32V6. Current display: resolution 0.005A, range 0-4.5A7. Conversion efficiency: about 94%, depending on the voltage difference and current efficiency8. Working current: about 30mA9. Input reverse polarity protection: yes10. Anti-backflow at the output: no (if charging the battery, first power on the module and then connect the battery, and ensure that the battery voltage is lower than the output voltage; if possible, connect an anti-backflow diode in series with the output positive pole)11. Short circuit protection: yes12. Size: about 70.5x48.4x28mm13. Weight: about 65g Features:1. Crystal shell, beautiful design, good touch texture of buttons, and output voltage set by button2. The button can control the output to turn off and on, and can set the power-on default to ON or OFF3. LCD can display input and output voltage, output current and output power4. The input terminal is protected against reverse connection, and the reverse connection will not burn5. High efficiency, high current, low heat generation, constant current value can be adjusted around 0-4.5A, suitable for office power supply, high-power LED constant current drive, lithium battery charging, etc.Function Description:1. There are IN/OUT and ON/OFF buttons on the left side of the module: the IN/OUT button switches the display of input voltage and output voltage, long press to switch the display of output current and output power; the ON/OFF button controls the output ON or OFF, long press Press to set the default output state is ON or OFF at the next power-on2. There are +/- two buttons on the right side of the module: + button press the output voltage to increase 0.05V, long press to continuously increase, and then long press to continuously increase 0.1V, 1V in slow steps; - button press the output voltage Decrease 0.05V, long press to continuously decrease, and then long press to continuously decrease 0.1V, 1V in slow steps3. ADJ-I is the current setting potentiometer. Turn clockwise to increase the set current. When the load current reaches the set current, it enters the constant current state, and the CC constant current indicator (red) lights up. The OUT indicator is the output status indicator, it is on when there is voltage at the output terminal, otherwise it is off; the CHAR indicator is the charging indicator, which is on when charging, and the FULL indicator is the full indicator. If the set constant current value is 2A, charging When the current reaches below 0.2A, turn the light, the FULL indicator is on, and the CHAR indicator is offInstructions:1. Use as an ordinary step-down module with overcurrent protection capability- Press the button to set the output voltage to the desired voltage value- Rotate the ADJ-I current adjustment potentiometer counterclockwise to the end, then measure the output short-circuit current with the 10A current range of the multimeter (connect the two test leads directly to the output terminal), and adjust the ADJ-I constant current potentiometer clockwise to make the output The current reaches the overcurrent protection value you want to set. (For example, the current value displayed by the multimeter is 2A, then the current can only reach 2A when the module is used, and the red constant current indicator light is on when the current reaches 2A, otherwise the indicator light is off) 2. Use as a battery charger- The module without constant current function cannot be used to charge the battery. Because the voltage difference between the exhausted battery and the charger is very large, the charging current is too large and the battery is damaged, so the battery should be used at the beginning. Constant current charging, when the charging reaches a certain level, it will automatically switch back to constant voltage charging- Determine the float voltage and charging current of the battery to be recharged; (if the lithium battery parameter is 3.7V/2200mAh, then the float voltage is 4.2V, and the charging current can reach 1C, that is, 2200mA)- Under no-load conditions, the output voltage of the button reaches the floating charge voltage; (if charging a 3.7V lithium battery, adjust the output voltage to 4.2V)- First turn the ADJ-I current adjustment potentiometer counterclockwise to the end, then measure the output short-circuit current with the 10A current range of the multimeter (just connect the two test leads to the output terminal directly), and adjust the ADJ-I constant current potentiometer clockwise to make the output The current reaches the predetermined charging current value- Connect the battery and charge (when setting: no battery is connected to the output terminal)3. Used as a high-power LED constant current driver module- Determine the operating current and operating voltage needed to drive the LED- Under no-load conditions, press the button to set the output voltage to reach the LED working voltage- First turn the ADJ-I current adjustment potentiometer counterclockwise to the end, then measure the output short-circuit current with the 10A current range of the multimeter (just connect the two test leads to the output terminal directly), and adjust the ADJ-I constant current potentiometer clockwise to make the output The current reaches the predetermined LED operating current- Connect the LED, test the machine (when setting: output no-load, do not connect the LED light) Precautions: 1. It is forbidden to short-circuit the input IN- of the module with the output OUT-, otherwise the constant current function will fail 2. Make sure that the power of the power supply is always greater than the power required by the output load. When the module is seriously hot, please reduce the power usage.

Read more less

1. Three-in-one electronic clock module, integrating three practical functions: time, thermometer and voltmeter2. Using RX8025T clock chip, the timing accuracy is stable3. The lengthened temperature probe can effectively solve the problem that the temperature affected by the module temperature is not accurate enough4. Power supply voltage: DC5.0-30V5. Temperature function range: -40-120 degrees Celsius, resolution 0.16. Voltmeter function range: DC5-30V (requires pure DC power supply, it is not recommended to use 24V battery, because the voltage may be too high during charging and burn)7. Size: about 4x1.4x1.3cmFunction and usage instructions:1. Adjust time, date, year, voltage error, temperature error cycle display item definition, alternate display interval time2. In the non-setting state, press the left key to enter the time adjustment (note that the colon in the middle is bright):- At this time, the minute bar starts to flash, press the right button to increase, the adjustment range is 00-59, after adjusting, press the left button again, the hour bar starts to flash, press the right button to increase, the adjustment range is 00-23- After adjusting the hour, press the left button again to enter the date adjustment (note that the colon in the middle is off), at this time the date column starts to flash, press the right button to increase, the adjustment range is 1-31, after the date is adjusted, press the left button again key, the month column starts to flash, press the right key to increase, the adjustment range is 1-12, after adjusting the date, press the left key again, the year column starts to flash, press the right key to increase, the adjustment range is 2012-2049- After adjusting the year, press the left key again to enter the error calibration function of the displayed voltage, the unit is 0.1V, a positive number means increase, and a negative number means decrease- Then press the left key again to enter the temperature error calibration setting, press the right key to increase, a positive number means increase, a negative number means decrease, the unit is Celsius- Press the left button again to enter the definition function dd option of the display item in the cycle display state,Press the right button to change the value: (dd:0) time + temperature + voltage, (dd: 1) time + temperature, (dd: 3) time + voltage- Press the left button again to enter the cycle display alternate interval time dF option, press the right button to change the value, the larger the value, the longer the interval- Press the left button again to save all the set values ??and return to the normal display state3. Switch display items: in the non-setting state, press the right key to switch the display items, and the display will switch between the time-date-temperature-voltage alternate display

Read more less

1. Material: ABS, electronic components2. Specifications: 4 terminals3. Scope of application: MODEM, CNC machine tools, industrial instruments, meters, testing equipment monitoring systems, automation control equipment and notebooks4. Output: 5V/200MA5. Support STC microcontroller download6. Support 115200 high baud rate7. Support serial port setting and debugging8. Distribute serial port debugging software9. No external power supply, USB interface to the computer10. Length: 31.5 cm

Read more less

1. Working voltage: DC 5-36V2. Trigger signal source: high-level trigger (DC 3.0V-24V) signal ground and system ground are not common to improve the anti-interference ability of the system (you can also short-circuit the common ground by yourself)3. Output capacity: DC 5V--36V, continuous current 15A at room temperature, power 400W, under auxiliary cooling conditions, the current can reach 30A4. Quiescent current: 15mA5. With optocoupler isolation, enhance anti-interference ability, industrial-grade circuit board, set parameters will be remembered forever after power off6. Size: about 6x3.4x1.2cm7. Note: The module is an active live output, the voltage of the output terminal (load terminal) is equal to the input terminal voltage (DC 5V--36V)Features:1. Realize high-frequency, fast and frequent on-off of the circuit2. The on-off process will not produce noise, no electrical sparks, and no electromagnetic interference.3. Adopt dual MOS parallel active output, lower internal resistance, higher current, strong power, 15A, 400W at room temperature, which meets the use of most equipment4. It is used to control motors, light bulbs, LED strips, DC motors, micro water pumps, solenoid valves, etc. Through this module, these devices can be easily controlled, which is very convenient5. Wide voltage operation (5-36V), most devices can be used, very convenient6. The interface is clear and simple, powerful and easy to operate7. One-key emergency stop function (STOP key), with reverse connection protection, reverse connection will not burn8. Added sleep mode, after enabling, if there is no operation within 5 minutes, the display will be automatically turned off, and any key will wake up9. Different OP, CL, LOP parameters can be set, these parameters are independent of each other and saved separately10. All setting parameters are automatically saved after power off

Read more less

1. Input voltage range: 6.00-60.00V2. Adjustable output voltage range: 0-50.00V3. Output power range: 0-1000W4. Adjustable output current range: 0-20.00A5. Output voltage resolution: 0.01V6. Output current resolution: 0.01A7. With power-down storage function, it can store 10 sets of preset values, and can quickly extract two sets of stored values.8. The LCD display on the module has digital voltmeter and ammeter functions9. In the output status reminder area, you can check the preset voltage, input voltage, output voltage, preset current, output current, output power, etc., you can see whether the output is on or not, the constant voltage and constant current status, whether the output is normal, and whether the key is pressed. lock, the data group currently in use10. In the setting data interface, you can adjust the overvoltage value, overcurrent value, overpower value, data setting and LCD brightness11. The module has the advantages of small size, advanced functions, good visual effects, high operability, high precision, independent use, embedded equipment, and wide application.12. Fixing hole center distance: 86mm, 64mm13. Display module size: 79x43x41mm14. Opening size: 71x39mm15. Power module size: 93x71x41mm16. Cable length: 200mm17. Product weight: about 222

Read more less

1. Output frequency range: ADF4351: 35M-4400M (4.4G)2. Output signal: 2200M-4400M fundamental wave (sine wave) 35M-2200M fundamental wave frequency division (square wave)3. Output signal interface: SMA female4. Control mode: three-wire SPI, lead out control pin and lock status pin, can realize all functions, including point frequency, sweep frequency and frequency hopping, step can reach 1K, low frequency step can reach 0.1K, according to crystal frequency to decide.5. It can be powered by 3.3v pins, and the power supply can provide a current of not less than 500mA.6. Typical power supply is 5v

Read more less

1. Material: electronic components2. Gain: 2.0dBi3. Frequency range: 1060-1120 MHz4. The antenna can be fixed on a conductive object connected to the ground, which can reduce electrostatic coupling interference5. Size: 17.9 x 2cm6. Weight: about 15 grams

Read more less

Features1. Function of this aluminum heat sink is to cool down the board and make it operate safely 2. The aluminum heat sink can reduce the risk of hardware failure because of overheating 3. Essential for high-performance computing: Keeps module temperatures low to avoid overheating and throttling. 4. Safe for use: Spring mounting interface keeps excessive pressure off the Jetson Nano module. 5. Compatible with Jetson Nano Module, with elastic bracket and height-limited screws 6. Easy to install: Mounting holes & screws included.Package List1. NANO-HEATSINK x1 2. Elastic bracket and height-limited screws x1

Read more less

FeaturesRaspberry Pi 4B main features: 1. BCM2711B0 64 bit 1.5GHz quad core processor with 4GB memory 2. It supports 4K 60fps high-resolution dual screen display by dual micro HDMI interface 3. Gigabit Ethernet port, Bluetooth 5.0 BLE, 2.4G / 5G dual-band WIFI 4. Dual USB2.0 interface, also with dual USB3.0 interface, faster transmission speed Camera Module + Wide Angle Lens: The camera module is based on the original high-quality camera of Raspberry Pi, which can provide higher resolution and higher sensitivity. With a 6mm wide-angle lens, it has better performance in visual fidelity. Raspberry Pi original high-quality camera features: 1. 12 million pixels 4056 (H) x 3040 (V), support RAW12 / 10 /8, COMP8 format output 2. 7.9mm CMOS diagonal length 3. C-mount/CS-mount lens standard with integrated IR filter Wide angle lens features: 1. 6mm Focal Length, 63 degree field angle, wider field of view 2. F1.2 Aperture, for more sufficient light entering, support manual adjustment The 4.3-inch IPS screen has the advantages of true color and large viewing angle. At the same time, the DSI display has a high frame rate and does not occupy the Raspberry Pi 40pin GPIO interface. The Raspberry Pi system has good compatibility and is an ideal match for this kit. 4.3-inch capacitive touch screen features: 1. 800 x 480 pixels IPS screen, combined with tempered glass panel, supports 5-points touch, and the visual angle can up to 160??° 2. Support DSI display interface, high frame rate, good compatibility with Raspberry Pi system Aluminum Alloy Bracket Large base for holding the object being viewed, free up and sown bracketPackage List1. PI4B-4GB x 1 2. Micro SD Card 16GB x 1 3. 4.3-inch DSI LCD x 1 4. 6mm Wide Angle Lens x 1 5. Microscope Bracket Kit x 1 6. Raspberry Pi HQ Camera x 1 7. Camera holder x 1 8. 5V 4A Type C US plug power supply x 1 9. 15Pin FFC ~30cm x 1 10. Screws pack x 1 11. Card reader x 1 12. Cooling fan x 1

Read more less

Features1. Adopt new version CH343G chip. Compared with CH340G, it supports higher data rate (up to 6Mbps) and more serial port IO levels (5V / 3.3V / 2.5V / 1.8V) 2. Support Mac, Linux, Android, Windows 7/8/8.1/10/11 3. Onboard resettable Fuse and Transient Voltage Suppressor, anti-overcurrent and anti-overvoltage, anti-surge, anti-static, improve shock resistance, stable and safe communication performance 4. Onboard IO protection circuits, anti-surge, anti-static, stable and safe communication performance 5. Onboard 3.3V and 5V TTL level switch pins for selecting TTL communication level 6. Support 3.3V/5V output (the module is powered by USB, and the onboard jumper should be shorted to 3.3V or 5V accordingly) 7. Adopt double-sided black immersion gold process, which is durable and has a good lookIndictor Description1. PWR: Power indicator, turn on when the voltage is detected from USB interface 2. RXD: Receiving indicator, turn on when data is sent back from the device interface 3. TXD: Sending indicator, turn on when data is sent from USBPinouts Definition1. VCC: 5V or 3.3V output for external device (configured by jumper) 2. GND: Ground 3. TXD: Connects to MCU.RXD 4. RXD: Connects to MCU.TXD 5. RTS: Connects to MCU.CTS 6. CTS: Connects to MCU.RTSSpecifications1. Host interface: USB 2. Device interface: UART 3. Communication range: 50bps ~ 6Mbps 4. USB device interface: Micro USB 5. Protection: resettable Fuse, ESD protection 6. UART interface connector: 6-pin right-angle pinheader 7. Protection: IO protection diode

Read more less

1. Touch screen expansion board + interface expander: The touch screen expansion board and an additional interface expander, with Gigabit Ethernet port, M.2 slot for connecting communication module or SSD, and more USB ports. 2. 2.8 inch display with 5-point capacitive touch control, better touch experience from the fully laminated screen, together with 6H toughened glass panel, more safe to use 3. Touch Screen Expansion Board Introduction: - CM4 socket: Suitable for all variants of Compute Module 4 - USB: USB 2.0 x 1 - Connector: MIPI CSI 22PIN 0.5mm camera connector - Display: 2.8 inch fully laminated screen, 480 x 640 pixels, 5-point capacitive touch, toughened glass panel - Video: Micro HDMI x 1, supports 4K 30fps output - Storage: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants - Power input: 5V 4. Interface Expander Introduction - Networking: Gigabit Ethernet RJ45; M.2 M KEY, support NVME SSD or communication module - USB: USB 2.0 x 3 Package list: 1. Touch screen expansion board x1 2. Screws pack x1 3. Interface expander x1

Read more less

Features1. Adopt new version CH343G chip. Compared with CH340G, it supports higher data rate (up to 6Mbps) and more serial port IO levels (5V / 3.3V / 2.5V / 1.8V) 2. Support Mac, Linux, Android, Windows 7/8/8.1/10/11 3. Onboard resettable Fuse and Transient Voltage Suppressor, anti-overcurrent and anti-overvoltage, anti-surge, anti-static, improve shock resistance, stable and safe communication performance 4. Onboard IO protection circuits, anti-surge, anti-static, stable and safe communication performance 5. Onboard 3.3V and 5V TTL level switch pins for selecting TTL communication level 6. Support 3.3V/5V output (the module is powered by USB, and the onboard jumper should be shorted to 3.3V or 5V accordingly) 7. Adopt double-sided black immersion gold process, which is durable and has a good lookIndictor Description1. PWR: Power indicator, turn on when the voltage is detected from USB interface 2. RXD: Receiving indicator, turn on when data is sent back from the device interface 3. TXD: Sending indicator, turn on when data is sent from USBPinouts Definition1. VCC: 5V or 3.3V output for external device (configured by jumper) 2. GND: Ground 3. TXD: Connects to MCU.RXD 4. RXD: Connects to MCU.TXD 5. RTS: Connects to MCU.CTS 6. CTS: Connects to MCU.RTSSpecifications1. Host interface: USB 2. Device interface: UART 3. Communication range: 50bps ~ 6Mbps 4. USB device interface: Mini USB 5. Protection: resettable Fuse, ESD protection 6. UART interface connector: 6-pin right-angle pinheader 7. Protection: IO protection diode

Read more less

Features1. Adopt new version CH343G chip. Compared with CH340G, it supports higher data rate (up to 6Mbps) and more serial port IO levels (5V / 3.3V / 2.5V / 1.8V) 2. Support Mac, Linux, Android, Windows 7/8/8.1/10/11 3. Onboard resettable Fuse and Transient Voltage Suppressor, anti-overcurrent and anti-overvoltage, anti-surge, anti-static, improve shock resistance, stable and safe communication performance 4. Onboard IO protection circuits, anti-surge, anti-static, stable and safe communication performance 5. Onboard 3.3V and 5V TTL level switch pins for selecting TTL communication level 6. Support 3.3V/5V output (the module is powered by USB, and the onboard jumper should be shorted to 3.3V or 5V accordingly) 7. Adopt double-sided black immersion gold process, which is durable and has a good lookIndictor Description1. PWR: Power indicator, turn on when the voltage is detected from USB interface 2. RXD: Receiving indicator, turn on when data is sent back from the device interface 3. TXD: Sending indicator, turn on when data is sent from USBPinouts Definition1. VCC: 5V or 3.3V output for external device (configured by jumper) 2. GND: Ground 3. TXD: Connects to MCU.RXD 4. RXD: Connects to MCU.TXD 5. RTS: Connects to MCU.CTS 6. CTS: Connects to MCU.RTSSpecifications1. Host interface: USB 2. Device interface: UART 3. Communication range: 50bps ~ 6Mbps 4. USB device interface: USB Type-C 5. Protection: resettable Fuse, ESD protection 6. UART interface connector: 6-pin right-angle pinheader 7. Protection: IO protection diode

Read more less

1. Pixels: 5MP 2. Sensor: OV5640 3. Interface: USB 2.0 4. Camera: Sensor size 1/4 inch 5. Aperture (F): 2.8 6. Focal length (EFL): 3.29 mm 7. Field of view (FOV): 68 degree 8. Distortion: Less than 1% 9. Focusing(B): AF Auto-Focus; 10. Image Format support: MJPG, YUV422 11. Static image resolution: 2592 x 1944 12. Video recording: 15 FPS 2592 x 1944, 30 FPS 1920 x 1080, 30 FPS 1280 x 720 13. Operating voltage: 5V +/- 5% 14. Camera size: 8.5 x 8.5 mm 15. Module size: 9 x 62 mm

Read more less

1. Pixels: 5MP 2. Sensor: OV5640 3. Interface: USB 2.0 4. Camera: Sensor size 1/4 inch 5. Aperture (F): 2.8 6. Focal length (EFL): 3.29 mm 7. Field of view (FOV): 68 degree 8. Distortion: Less than 1% 9. Focusing(C): FF Fixed-Focus 10. Image Format support: MJPG, YUV422 11. Static image resolution: 2592 x 1944 12. Video recording: 15 FPS 2592 x 1944, 30 FPS 1920 x 1080, 30 FPS 1280 x 720 13. Operating voltage: 5V +/- 5% 14. Camera size: 8.5 x 8.5 mm 15. Module size: 9 x 62 mm

Read more less

Features1. Adopt new version CH343G chip. Compared with CH340G, it supports higher data rate (up to 6Mbps) and more serial port IO levels (5V / 3.3V / 2.5V / 1.8V) 2. Support Mac, Linux, Android, Windows 7/8/8.1/10/11 3. Onboard resettable Fuse and Transient Voltage Suppressor, anti-overcurrent and anti-overvoltage, anti-surge, anti-static, improve shock resistance, stable and safe communication performance 4. Onboard IO protection circuits, anti-surge, anti-static, stable and safe communication performance 5. Onboard 3.3V and 5V TTL level switch pins for selecting TTL communication level 6. Support 3.3V/5V output (the module is powered by USB, and the onboard jumper should be shorted to 3.3V or 5V accordingly) 7. Adopt double-sided black immersion gold process, which is durable and has a good lookSpecifications1. Host interface: USB 2. Device interface: UART 3. Communication range: 50bps ~ 6Mbps 4. USB device interface: USB Type-A 5. Protection: resettable Fuse, ESD protection 6. UART interface connector: 6-pin right-angle pinheader 7. Protection: IO protection diodeIndictor Description1. PWR: Power indicator, turn on when the voltage is detected from USB interface 2. RXD: Receiving indicator, turn on when data is sent back from the device interface 3. TXD: Sending indicator, turn on when data is sent from USBPinouts Definition1. VCC: 5V or 3.3V output for external device (configured by jumper) 2. GND: Ground 3. TXD: Connects to MCU.RXD 4. RXD: Connects to MCU.TXD 5. RTS: Connects to MCU.CTS 6. CTS: Connects to MCU.RTS

Read more less

1. GPU: 128-core Maxwell 2. CPU: Quad-core ARM A57 1.43 GHz 3. Memory: 4GB 64-bit LPDDR4 25.6 GB/s 4. Storage: 16GB eMMC (no micro SD card slot) 5. Video encoder: 4K 30, 4x 1080p 30, 9x 720p 30 (H.264/H.265) 6. Video decoder: 4K 60, 2x 4K 30, 8x 1080p 30, 18x 720p 30 (H.264/H.265) 7. Camera: 2x MIPI CSI-2 DPHY lanes 8. Connectivity: Gigabit Ethernet, M.2 Key E expansion connector 9. Display: HDMI and DP 10. USB: 4x USB 3.0, USB 2.0 Micro-B 11. Extension interfaces: GPIO, I2C, I2S, SPI, UART 12. Dimensions: 100 x 80 x 29mm 13. Other: 260-pin connector

Read more less

1. Sensor: IMX378 2. CMOS size:1/2.3 inch 3. Camera type: Color Pixels: 12.3MP (4056 x 3040) 4. Shutter: Rolling Shutter 5. Aperture: F2.4 6. Distortion: Less than 58% 7. Field of vies: 190 degree 8. Focal length: 6.5mm 8. Focusing: Fixed focus distance

Read more less

Features1. 13.3 inch IPS screen,1920 x 1080 high resolution. 2. Embed Raspberry Pi 3A+ as controller. 3. Toughened glass capacitive touch panel, 6H hardness, supports up to 10-points touch. 4. Embedded ferrite Hi-Fi speaker. 5. Embedded microphone and speaker, adopts snowboy hotword detection engine. 6. 75x75mm spacing mounting holes (M4 screw hole). 7. Comes with a 75 degree tilt angle stand.Package List1. 13.3 inch PiPad x 1 2. 12V power adapter x 1 3. Card reader x 1 4. Micro SD card x 1

Read more less

FeaturesThe Compute Module PoE Board is a development board that you can plug a Raspberry Pi Compute Module into, and make use of the resources of Pi more flexibly. With the PoE (Power over Ethernet) feature, and versatile onboard peripheral interfaces, it is suitable for evaluating the Raspberry Pi compute module, also is an ideal choice for end products. 1. Raspberry Pi GPIO header, for connecting sorts of Raspberry Pi HATs. 2. 10/100M auto-negotiation Ethernet port, with PoE enabled. 3. 4 x USB ports, which allows connecting more USB devices. 4. 2 x CSI camera interfaces. 5. Onboard HDMI / DSI interfaces for connecting displays. 6. Onboard USB TO UART, for serial debugging. 7. Cooling fan interface, autorun on power-up OR controlled by IO pins. 8. Adopt isolated SMPS (Switching mode power supply).Specifications1. Power supply: Micro USB port / PoE Ethernet port 2. PoE power input: 37V ~ 57V DC in 3. PoE power output: 5V 2.5A DC out 4. Operating Temperature: -25 degree C ~ 80 degree C 5. Network standard: 802.3af PoE standard 6. Dimensions: 144mm x 88mm 7. Mounting hole size: 3.2mm

Read more less

Features1. 13.3 inch IPS screen,1920 x 1080 high resolution. 2. Embed Raspberry Pi 3A+ as controller 3. One-way mirror, can display news, weather and time. 4. Toughened glass capacitive touch panel, 6H hardness, supports up to 10-points touch. 5. Embedded ferrite Hi-Fi speaker. 6. Embedded Microphone And Speaker, Adopts Snowboy Hotword Detection Engine. 7. 75 x 75mm spacing mounting holes (M4 screw hole) for a general wall mount. 8. Comes with a 75 degree tilt angle stand.Package List1. 13.3 inch Magic Mirror x 1 2. 12V power adapter x 1 3. Card reader x 1 4. Micro SD card x 1

Read more less

Features1. 13.3 inch IPS screen,1920 x 1080 high resolution. 2. Embed Raspberry Pi 3A+ as controller 3. One-way mirror, can display news, weather and time. 4. Toughened glass capacitive touch panel, 6H hardness, supports up to 10-points touch. 5. Embedded ferrite Hi-Fi speaker. 6. Embedded Microphone And Speaker, Adopts Snowboy Hotword Detection Engine. 7. 75 x 75mm spacing mounting holes (M4 screw hole) for a general wall mount. 8. Comes with a 75 degree tilt angle stand.Package List1. 13.3 inch Magic Mirror x 1 2. 12V power adapter x 1 3. Card reader x 1 4. Micro SD card x 1

Read more less

Features1. 13.3 inch IPS screen,1920 x 1080 high resolution. 2. Embed Raspberry Pi 3A+ as controller. 3. Toughened glass capacitive touch panel, 6H hardness, supports up to 10-points touch. 4. Embedded ferrite Hi-Fi speaker. 5. Embedded microphone and speaker, adopts snowboy hotword detection engine. 6. 75x75mm spacing mounting holes (M4 screw hole). 7. Comes with a 75 degree tilt angle stand.Package List1. 13.3 inch PiPad x 1 2. 12V power adapter x 1 3. Card reader x 1 4. Micro SD card x 1

Read more less

FeaturesThe Compute Module PoE Board is a development board that you can plug a Raspberry Pi Compute Module into, and make use of the resources of Pi more flexibly. With the PoE (Power over Ethernet) feature, and versatile onboard peripheral interfaces, it is suitable for evaluating the Raspberry Pi compute module, also is an ideal choice for end products. 1. Raspberry Pi GPIO header, for connecting sorts of Raspberry Pi HATs. 2. 10/100M auto-negotiation Ethernet port, with PoE enabled. 3. 4 x USB ports, which allows connecting more USB devices. 4. 2 x CSI camera interfaces. 5. Onboard HDMI / DSI interfaces for connecting displays. 6. Onboard USB TO UART, for serial debugging. 7. Cooling fan interface, autorun on power-up OR controlled by IO pins. 8. Adopt isolated SMPS (Switching mode power supply).Specifications1. Power supply: Micro USB port / PoE Ethernet port 2. PoE power input: 37V ~ 57V DC in 3. PoE power output: 5V 2.5A DC out 4. Operating Temperature: -25 degree C ~ 80 degree C 5. Network standard: 802.3af PoE standard 6. Dimensions: 144mm x 88mm 7. Mounting hole size: 3.2mm

Read more less

1. Digital tube display and LCD display version: only temperature control function, without manual control2. Version without display WFT1: with temperature control and manual switch function, can be manually opened and closed remotely, timing, time delay, cycle switch and other settings (timing delay function, need to keep WIFI has been networking), otherwise the time settings are invalidated3. Product power supply: DC6-30V (recommended 24V or less), WFT1 with 5V MICRO-USB power supply port control terminal for the relay passive output, can be turned on and off the DC voltage and 220V AC voltage (current is recommended to be used within 7A)4. With cloud temperature records, switching action WeChat, e-mail notification, local buzzer alarms5. Networking instructions: ensure that the phone has been connected to the WiFi network, must be 24Ghz band, 5Ghz band can not be paired, if your router 2.4Ghz band and 5Ghz band is combined, please reconfigure the router, separate it, select the 2.4G band for pairing6. Size:- WFT1: 65 x 33mm- WT02-W: 79 x 43 x 27mm- WT03-W: 79 x 43 x 27mm7. Weight:- WFT1: 30g- WT02-W: 50g- WT03-W: 53gNote: electronic module products, you need to have a certain degree of electronic foundation

Read more less

FeaturesThe WAVEGO is a high-DOF bionic dog-like robot which features 2.3kg.cm large torque servos, reliable structure, and flexible motion, incorporating devices like front camera, 9-axes motion tracker, RGB indicator, etc., together with open source multi-platform Web application. It uses the ESP32 as sub controller for connecting rod inverse solving and gait generation, sharing calculating task for the host controller, an additional Raspberry Pi can be attached as the host controller for high-level decision operating. 1. Overall 12-DOF, multi connecting rods leg design, increasing the servo effective torque 2. A real time operating system is used as sub controller for connecting rod inverse solving and gait generation, sharing calculating task for the host controller and improving the gait solving efficiency 3. Ultra compact structure design, allows using on the table, aluminum alloy + nylon structure materials, ensuring strength while keeping it light weight 4. Additional Raspberry Pi can beattached as the host controller to enable OpenCV high-level functions, demo codes including facial recognition, motion detection, color tracking, and more. Reserved extension interface for secondary development, along with user manual and secondary development documents.SpecificationsGeneral: 1. Product name: WAVEGO high-DOF bionic quadruped robot 2. Stand up: length 218mm, width 116mm, height 152mm 3. Lie down: length 228mm, width 116mm, height 127mm 4. Overall weight: 465g (with batteries) 5. DOF: 12 overall, 3 per single leg Operating system: Demo code: FreeRTOS + Raspberry Pi OS Motion performance: 1. Available gait: Shake hands, stand up, crouch slowly, diagonal gait , jump, self-balancing 2. Motion extension: Providing motion programming example, including flexible Bezier curve speed motion function 3. Load: 300g Servo info.: 1. Dimensions: 23.2 x12.1 x25.25 mm 2. Weight: 13.0 +/- 1g 3. Operating voltage: 6V 4. Idle speed: 0.1sec/60 degree (100RPM) 5. Stalling torque: 2.3kg.cm (31.99oz.in) 6. Rated load: 0.7kg.cm 7. Rated current: 350mA 8. Control method: Pulse width modification 9. Control system type: Digital comparator Visual function: 1. FreeRTOS demo: Web-based real time video streaming 2. Raspberry Pi OS demo: Real time video streaming, facial recognition, color tracking, moving object detection Note: All the demo codes are open sourced, the Raspberry Pi OS demo is based on open source projects flask-streaming and OpenCV Processor and memory: 1. ESP32 sub controller: Processor: Xtensa LX6 dual-core processor 240MHz 2. SRAM: 520KB+8MB 3. Flash: 448KB+4MB Others: 1. WiFi standard: 802.11b/g/n 2. Bluetooth standard: Bluetooth 4.2, including traditional Bluetooth (BR/EDR) and Bluetooth low energy (BLE) 3. External port: 2 x 5P multi-function extension port (host controller communication, power supply selection, assembly mode selection, etc.) 4. DC battery charger jack: Type-C (download, UART communication, peripheral expansion) Power supply: 1. Battery type: 18650 Li-ion batteries (NOT included) 2. Supply voltage: 7-8.4V 3. Recharge voltage: 8.4V 4. Protection: Over charge, discharge protection, over current protection, short circuit protection, reverse proof, equalizing charge, stable and safe operating 5. Output voltage: provides 5V output for other host controllerPackage List1. WAVEGO body case x 1 2. WAVEGO basic parts x 1 3. Semi-transparent acrylic panel x 1 4. Double-sided sticker x 1 5. WAVEGO base board x 1 6. 2MP camera x 1 7. 2.4G antenna x 1 8. 0.91 inch OLED display x 1 9. Micro thrust bearing x 14 10. Micro ball flange bearing x30 11. USB cable (~1m) x 1 12. Plus screwdriver x 1 13. Cross wrench sleeve x 1 14. IPEX 1 to SMA cable (~17cm) x 1 15. Jumper wire (~20cm) x4 16. 4PIN PH2.0 cable x 1 17. Servo pack x 1 18. 8.4V 2A battery charger x 1 19. Screws and standoffs x 1

Read more less

FeaturesThe WAVEGO is a high-DOF bionic dog-like robot which features 2.3kg.cm large torque servos, reliable structure, and flexible motion, incorporating devices like front camera, 9-axes motion tracker, RGB indicator, etc., together with open source multi-platform Web application. It uses the ESP32 as sub controller for connecting rod inverse solving and gait generation, sharing calculating task for the host controller, an additional Raspberry Pi can be attached as the host controller for high-level decision operating. 1. Overall 12-DOF, multi connecting rods leg design, increasing the servo effective torque 2. A real time operating system is used as sub controller for connecting rod inverse solving and gait generation, sharing calculating task for the host controller and improving the gait solving efficiency 3. Ultra compact structure design, allows using on the table, aluminum alloy + nylon structure materials, ensuring strength while keeping it light weight 4. Additional Raspberry Pi can beattached as the host controller to enable OpenCV high-level functions, demo codes including facial recognition, motion detection, color tracking, and more. Reserved extension interface for secondary development, along with user manual and secondary development documents.SpecificationsGeneral: 1. Product name: WAVEGO high-DOF bionic quadruped robot 2. Stand up: length 218mm, width 116mm, height 152mm 3. Lie down: length 228mm, width 116mm, height 127mm 4. Overall weight: 465g (with batteries) 5. DOF: 12 overall, 3 per single leg Operating system: Demo code: FreeRTOS + Raspberry Pi OS Motion performance: 1. Available gait: Shake hands, stand up, crouch slowly, diagonal gait , jump, self-balancing 2. Motion extension: Providing motion programming example, including flexible Bezier curve speed motion function 3. Load: 300g Servo info.: 1. Dimensions: 23.2 x12.1 x25.25 mm 2. Weight: 13.0 +/- 1g 3. Operating voltage: 6V 4. Idle speed: 0.1sec/60 degree (100RPM) 5. Stalling torque: 2.3kg.cm (31.99oz.in) 6. Rated load: 0.7kg.cm 7. Rated current: 350mA 8. Control method: Pulse width modification 9. Control system type: Digital comparator Visual function: 1. FreeRTOS demo: Web-based real time video streaming 2. Raspberry Pi OS demo: Real time video streaming, facial recognition, color tracking, moving object detection Note: All the demo codes are open sourced, the Raspberry Pi OS demo is based on open source projects flask-streaming and OpenCV Processor and memory: 1. ESP32 sub controller: Processor: Xtensa LX6 dual-core processor 240MHz 2. SRAM: 520KB+8MB 3. Flash: 448KB+4MB Others: 1. WiFi standard: 802.11b/g/n 2. Bluetooth standard: Bluetooth 4.2, including traditional Bluetooth (BR/EDR) and Bluetooth low energy (BLE) 3. External port: 2 x 5P multi-function extension port (host controller communication, power supply selection, assembly mode selection, etc.) 4. DC battery charger jack: Type-C (download, UART communication, peripheral expansion) Power supply: 1. Battery type: 18650 Li-ion batteries (NOT included) 2. Supply voltage: 7-8.4V 3. Recharge voltage: 8.4V 4. Protection: Over charge, discharge protection, over current protection, short circuit protection, reverse proof, equalizing charge, stable and safe operating 5. Output voltage: provides 5V output for other host controllerPackage List1. WAVEGO body case x 1 2. WAVEGO basic parts x 1 3. Semi-transparent acrylic panel x 1 4. Double-sided sticker x 1 5. WAVEGO base board x 1 6. 2MP camera x 1 7. 2.4G antenna x 1 8. 0.91 inch OLED display x 1 9. Micro thrust bearing x 14 10. Micro ball flange bearing x30 11. USB cable (~1m) x 1 12. Plus screwdriver x 1 13. Cross wrench sleeve x 1 14. IPEX 1 to SMA cable (~17cm) x 1 15. Jumper wire (~20cm) x4 16. 4PIN PH2.0 cable x 1 17. Servo pack x 1 18. 8.4V 2A battery charger x 1 19. Screws and standoffs x 1

Read more less

1. Suitable for evaluating the Raspberry Pi CM4 Or being integrated into end products 2. Standard CM4 socket, 40PIN GPIO, gigabit ethernet, USB2.0, DSI, CSI, 3.5mm Audio Jack... 3. All in the compact body just as the size of CM4 Specifications: 1. CM4 socket: Suitable for all variants of Compute Module 4 2. Networking: Gigabit Ethernet RJ45 connector 3. Connector: Raspberry Pi 40PIN GPIO header x 1 4. USB: USB 2.0 Type A connector x 1 5. Display: MIPI DSI port x 1 (15pin 1.0mm FPC connector) 6. Camera: MIPI CSI-2 port x 1 (15pin 1.0mm FPC connector) 7. Video: Mini HDMI port x 1, supports 4K 30fps output 8. Audio: 3.5mm jack 9. Storage: Micro SD card socket for Compute Module 4 Lite (without eMMC) variants 10. Power input: 5V 11. Dimension: 56 x 41mm Package list: 1. CM4-NANO-B x 1 3. 2*20PIN color-coded straight pinheader x 1

Read more less

FeaturesThe WAVEGO is a high-DOF bionic dog-like robot which features 2.3kg.cm large torque servos, reliable structure, and flexible motion, incorporating devices like front camera, 9-axes motion tracker, RGB indicator, etc., together with open source multi-platform Web application. It uses the ESP32 as sub controller for connecting rod inverse solving and gait generation, sharing calculating task for the host controller, an additional Raspberry Pi can be attached as the host controller for high-level decision operating. 1. Overall 12-DOF, multi connecting rods leg design, increasing the servo effective torque 2. A real time operating system is used as sub controller for connecting rod inverse solving and gait generation, sharing calculating task for the host controller and improving the gait solving efficiency 3. Ultra compact structure design, allows using on the table, aluminum alloy + nylon structure materials, ensuring strength while keeping it light weight 4. Additional Raspberry Pi can beattached as the host controller to enable OpenCV high-level functions, demo codes including facial recognition, motion detection, color tracking, and more. Reserved extension interface for secondary development, along with user manual and secondary development documents.SpecificationsGeneral: 1. Product name: WAVEGO high-DOF bionic quadruped robot 2. Stand up: length 218mm, width 116mm, height 152mm 3. Lie down: length 228mm, width 116mm, height 127mm 4. Overall weight: 465g (with batteries) 5. DOF: 12 overall, 3 per single leg Operating system: Demo code: FreeRTOS + Raspberry Pi OS Motion performance: 1. Available gait: Shake hands, stand up, crouch slowly, diagonal gait , jump, self-balancing 2. Motion extension: Providing motion programming example, including flexible Bezier curve speed motion function 3. Load: 300g Servo info.: 1. Dimensions: 23.2 x12.1 x25.25 mm 2. Weight: 13.0 +/- 1g 3. Operating voltage: 6V 4. Idle speed: 0.1sec/60 degree (100RPM) 5. Stalling torque: 2.3kg.cm (31.99oz.in) 6. Rated load: 0.7kg.cm 7. Rated current: 350mA 8. Control method: Pulse width modification 9. Control system type: Digital comparator Visual function: 1. FreeRTOS demo: Web-based real time video streaming 2. Raspberry Pi OS demo: Real time video streaming, facial recognition, color tracking, moving object detection Note: All the demo codes are open sourced, the Raspberry Pi OS demo is based on open source projects flask-streaming and OpenCV Processor and memory: 1. ESP32 sub controller: Processor: Xtensa LX6 dual-core processor 240MHz 2. SRAM: 520KB+8MB 3. Flash: 448KB+4MB Others: 1. WiFi standard: 802.11b/g/n 2. Bluetooth standard: Bluetooth 4.2, including traditional Bluetooth (BR/EDR) and Bluetooth low energy (BLE) 3. External port: 2 x 5P multi-function extension port (host controller communication, power supply selection, assembly mode selection, etc.) 4. DC battery charger jack: Type-C (download, UART communication, peripheral expansion) Power supply: 1. Battery type: 18650 Li-ion batteries (NOT included) 2. Supply voltage: 7-8.4V 3. Recharge voltage: 8.4V 4. Protection: Over charge, discharge protection, over current protection, short circuit protection, reverse proof, equalizing charge, stable and safe operating 5. Output voltage: provides 5V output for other host controllerPackage List1. WAVEGO body case x 1 2. WAVEGO basic parts x 1 3. Semi-transparent acrylic panel x 1 4. Double-sided sticker x 1 5. WAVEGO base board x 1 6. 2MP camera x 1 7. 2.4G antenna x 1 8. 0.91 inch OLED display x 1 9. Micro thrust bearing x 14 10. Micro ball flange bearing x30 11. USB cable (~1m) x 1 12. Plus screwdriver x 1 13. Cross wrench sleeve x 1 14. IPEX 1 to SMA cable (~17cm) x 1 15. Jumper wire (~20cm) x4 16. 4PIN PH2.0 cable x 1 17. Servo pack x 1 18. 8.4V 2A battery charger x 1 19. Screws and standoffs x 1

Read more less

1. Design with good heat dissipation, do not have to install the cooling fan or heatsink. 2. This case is constructed out of high quality aluminum material. 3. Suitable for Raspberry Pi 4 only 4. Access to all ports of Raspberry Pi 4 5. Cable interface is reserved, support to install cable. Note: Please insert the Micro SD card to Raspberry Pi before installing the case.

Read more less

FeaturesThe WAVEGO is a high-DOF bionic dog-like robot which features 2.3kg.cm large torque servos, reliable structure, and flexible motion, incorporating devices like front camera, 9-axes motion tracker, RGB indicator, etc., together with open source multi-platform Web application. It uses the ESP32 as sub controller for connecting rod inverse solving and gait generation, sharing calculating task for the host controller, an additional Raspberry Pi can be attached as the host controller for high-level decision operating. 1. Overall 12-DOF, multi connecting rods leg design, increasing the servo effective torque 2. A real time operating system is used as sub controller for connecting rod inverse solving and gait generation, sharing calculating task for the host controller and improving the gait solving efficiency 3. Ultra compact structure design, allows using on the table, aluminum alloy + nylon structure materials, ensuring strength while keeping it light weight 4. Additional Raspberry Pi can beattached as the host controller to enable OpenCV high-level functions, demo codes including facial recognition, motion detection, color tracking, and more. Reserved extension interface for secondary development, along with user manual and secondary development documents.SpecificationsGeneral: 1. Product name: WAVEGO high-DOF bionic quadruped robot 2. Stand up: length 218mm, width 116mm, height 152mm 3. Lie down: length 228mm, width 116mm, height 127mm 4. Overall weight: 554g (with batteries) 5. DOF: 12 overall, 3 per single leg Operating system: Demo code: FreeRTOS + Raspberry Pi OS Motion performance: 1. Available gait: Shake hands, stand up, crouch slowly, diagonal gait , jump, self-balancing 2. Motion extension: Providing motion programming example, including flexible Bezier curve speed motion function 3. Load: 200g Servo info.: 1. Dimensions: 23.2 x12.1 x25.25 mm 2. Weight: 13.0 +/- 1g 3. Operating voltage: 6V 4. Idle speed: 0.1sec/60 degree (100RPM) 5. Stalling torque: 2.3kg.cm (31.99oz.in) 6. Rated load: 0.7kg.cm 7. Rated current: 350mA 8. Control method: Pulse width modification 9. Control system type: Digital comparator Visual function: 1. FreeRTOS demo: Web-based real time video streaming 2. Raspberry Pi OS demo: Real time video streaming, facial recognition, color tracking, moving object detection Note: All the demo codes are open sourced, the Raspberry Pi OS demo is based on open source projects flask-streaming and OpenCV Processor and memory: 1. ESP32 sub controller: Processor: Xtensa LX6 dual-core processor 240MHz 2. SRAM: 520KB+8MB 3. Flash: 448KB+4MB Others: 1. WiFi standard: 802.11b/g/n 2. Bluetooth standard: Bluetooth 4.2, including traditional Bluetooth (BR/EDR) and Bluetooth low energy (BLE) 3. External port: 2 x 5P multi-function extension port (host controller communication, power supply selection, assembly mode selection, etc.) 4. DC battery charger jack: Type-C (download, UART communication, peripheral expansion) Power supply: 1. Battery type: 18650 Li-ion batteries (NOT included) 2. Supply voltage: 7-8.4V 3. Recharge voltage: 8.4V 4. Protection: Over charge, discharge protection, over current protection, short circuit protection, reverse proof, equalizing charge, stable and safe operating 5. Output voltage: provides 5V output for other host controllerPackage List1. WAVEGO body case x 1 2. WAVEGO basic parts x 1 3. Semi-transparent acrylic panel x 1 4. Double-sided sticker x 1 5. WAVEGO base board x 1 6. 2MP camera x 1 7. 2.4G antenna x 1 8. 0.91inch OLED display x 1 9. Micro thrust bearing x 14 10. Micro ball flange bearing x 30 11. USB cable (~1m) x 1 12. Plus screwdriver x 1 13. Cross wrench sleeve x 1 14. IPEX 1 to SMA cable (~17cm) x 1 15. Jumper wire (~20cm) x 4 16. 4 PIN PH2.0 cable x 1 17. Servo pack x 1 18. 8.4V 2A battery charger x 1 19. Screws and standoffs x 1

Read more less

Features1. 5inch IPS capacitive touch screen, 800 x 480 resolution 2. Compatible with Raspberry Pi 4B/3B+/3A+/3B/2B/B+/A+, CM3/3+/4 (CM3/3+/4 requires extra adapter board) 3. The LCD is directly driven by Raspberry Pi DPI interface 4. Backlight can be turned off to lower power consumption 5. Toughened glass capacitive touch panel, 5-points touch 6. Compact size, suit for various projectsDevice & System Support1. Support Raspberry Pi OS, 5-points touch, driver free 2. Support Ubuntu / Kali / WIN10 IoT, single point touch, driver free 3. Support Retropie, driver freePackage List1. 5 inch DSI LCD (B) x 1 2. FPC 15PIN 1.0 pitch 50mm (opposite sides) x 1 3. Screws pack x 1

Read more less

FeaturesThe WAVEGO is a high-DOF bionic dog-like robot which features 2.3kg.cm large torque servos, reliable structure, and flexible motion, incorporating devices like front camera, 9-axes motion tracker, RGB indicator, etc., together with open source multi-platform Web application. It uses the ESP32 as sub controller for connecting rod inverse solving and gait generation, sharing calculating task for the host controller, an additional Raspberry Pi can be attached as the host controller for high-level decision operating. 1. Overall 12-DOF, multi connecting rods leg design, increasing the servo effective torque 2. A real time operating system is used as sub controller for connecting rod inverse solving and gait generation, sharing calculating task for the host controller and improving the gait solving efficiency 3. Ultra compact structure design, allows using on the table, aluminum alloy + nylon structure materials, ensuring strength while keeping it light weight 4. Additional Raspberry Pi can beattached as the host controller to enable OpenCV high-level functions, demo codes including facial recognition, motion detection, color tracking, and more. Reserved extension interface for secondary development, along with user manual and secondary development documents.SpecificationsGeneral: 1. Product name: WAVEGO high-DOF bionic quadruped robot 2. Stand up: length 218mm, width 116mm, height 152mm 3. Lie down: length 228mm, width 116mm, height 127mm 4. Overall weight: 554g (with batteries) 5. DOF: 12 overall, 3 per single leg Operating system: Demo code: FreeRTOS + Raspberry Pi OS Motion performance: 1. Available gait: Shake hands, stand up, crouch slowly, diagonal gait , jump, self-balancing 2. Motion extension: Providing motion programming example, including flexible Bezier curve speed motion function 3. Load: 200g Servo info.: 1. Dimensions: 23.2 x12.1 x25.25 mm 2. Weight: 13.0 +/- 1g 3. Operating voltage: 6V 4. Idle speed: 0.1sec/60 degree (100RPM) 5. Stalling torque: 2.3kg.cm (31.99oz.in) 6. Rated load: 0.7kg.cm 7. Rated current: 350mA 8. Control method: Pulse width modification 9. Control system type: Digital comparator Visual function: 1. FreeRTOS demo: Web-based real time video streaming 2. Raspberry Pi OS demo: Real time video streaming, facial recognition, color tracking, moving object detection Note: All the demo codes are open sourced, the Raspberry Pi OS demo is based on open source projects flask-streaming and OpenCV Processor and memory: 1. ESP32 sub controller: Processor: Xtensa LX6 dual-core processor 240MHz 2. SRAM: 520KB+8MB 3. Flash: 448KB+4MB Others: 1. WiFi standard: 802.11b/g/n 2. Bluetooth standard: Bluetooth 4.2, including traditional Bluetooth (BR/EDR) and Bluetooth low energy (BLE) 3. External port: 2 x 5P multi-function extension port (host controller communication, power supply selection, assembly mode selection, etc.) 4. DC battery charger jack: Type-C (download, UART communication, peripheral expansion) Power supply: 1. Battery type: 18650 Li-ion batteries (NOT included) 2. Supply voltage: 7-8.4V 3. Recharge voltage: 8.4V 4. Protection: Over charge, discharge protection, over current protection, short circuit protection, reverse proof, equalizing charge, stable and safe operating 5. Output voltage: provides 5V output for other host controllerPackage List1. WAVEGO body case x 1 2. WAVEGO basic parts x 1 3. Semi-transparent acrylic panel x 1 4. Double-sided sticker x 1 5. WAVEGO base board x 1 6. 2MP camera x 1 7. 2.4G antenna x 1 8. 0.91inch OLED display x 1 9. Micro thrust bearing x 14 10. Micro ball flange bearing x 30 11. USB cable (~1m) x 1 12. Plus screwdriver x 1 13. Cross wrench sleeve x 1 14. IPEX 1 to SMA cable (~17cm) x 1 15. Jumper wire (~20cm) x 4 16. 4 PIN PH2.0 cable x 1 17. Servo pack x 1 18. 8.4V 2A battery charger x 1 19. Screws and standoffs x 1

Read more less

1. 1MP, global shutter, 120 degree FOV, OV9281-120 mono camera, compatible with Raspberry Pi series boards 2. The global shutter eliminates jello-effect while shooting fast moving objects, more suitable for high frame rate capturing 3. Working with Raspberry Pi, direct connect to Raspberry Pi different variants including 4B / 3B+ / 3A+ / 3B / 2B / B+ / A+, extra FPC cable is equired for Zero / Zero 2 W series Specifications: 1. Sensor: OV9281 2. CMOS size: 1/4 inch 3. Camera type: Mono 4. Pixels: 1MP (1280 x 800) 5. Shutter: Global Shutter 6. Aperture: F2.5 7. Distortion: Less than 7.5% 8. Field of vies: 120 degree 9. Focal length: 3.15mm 10. Focusing: Fixed focus Package List: 1. OV9281-120 Camera x 1 2. 15-pin FFC (opposite sides contact) x 1

Read more less

FeaturesBased on a high performance Cortex processor, combined with high-security commercial fingerprinting algorithm, the UART Fingerprint Sensor (E) features functionalities like fingerprint enrolling, image acquisition, feature finding, fingerprint matching, and so on. Without any knowledge about the complicate fingerprinting algorithm, all you need to do is just sending some UART commands, to quickly integrate it into fingerprint verification applications which require small size and high precision. 1. Easy to use by some simple commands, you do not have to know any fingerprint technology, or the module inter structure 2. Commercial fingerprinting algorithm, supports functions like fingerprint enrolling, fingerprint matching, fingerprint image acquisition, and fingerprint feature uploading, stable performance, fast identification 3. Capacitive sensitive detection, just touch the collecting window lightly for fast verification 4. Highly integrated hardware, processor and sensor in one small chip, suitable for small size applications 5. Embedded human sensor, the processor will enter sleep automatically, and wake up when touching, lower power consumption 6. Onboard UART connector, easy to connect with hardware platforms like STM32 and Raspberry PiSpecifications1. Sensor: Capacitive touch sensor 2. Resolution: 508 DPI 3. Image pixels: 160 x 160 4. Image greyscale: 8 5. Sensor dimension: 11.2 x 12.2 mm 6. Fingerprint capacity: 3000 7. Matching time: Less than 200ms (1:N, and N less than or equal to 100) 8. False acceptance rate: Less than 0.001% 9. False rejection rate: Less than 0.1% 10. Operating voltage: 3.3V 11. Operating current: Less than 50mA 12. Sleep current: Less than 16uA 13. ESD: Contact discharge 8KV / aerial discharge 15KV 14. Communication port: UART 15. Baudrate: 19200 bps 16. Operating environment: Temperature: -20 degree C~70 degree C; 17. Humidity: 40%RH~85%RH (no condensation) 18. Storage environment: Temperature: -40 degree C~85 degree C; Humidity: Less than 85%RH (no condensation)Package List1. UART Fingerprint Sensor (E) x 1 2. 6PIN squid wire x 1

Read more less

FeaturesThe WAVEGO is a high-DOF bionic dog-like robot which features 2.3kg.cm large torque servos, reliable structure, and flexible motion, incorporating devices like front camera, 9-axes motion tracker, RGB indicator, etc., together with open source multi-platform Web application. It uses the ESP32 as sub controller for connecting rod inverse solving and gait generation, sharing calculating task for the host controller, an additional Raspberry Pi can be attached as the host controller for high-level decision operating. 1. Overall 12-DOF, multi connecting rods leg design, increasing the servo effective torque 2. A real time operating system is used as sub controller for connecting rod inverse solving and gait generation, sharing calculating task for the host controller and improving the gait solving efficiency 3. Ultra compact structure design, allows using on the table, aluminum alloy + nylon structure materials, ensuring strength while keeping it light weight 4. Additional Raspberry Pi can beattached as the host controller to enable OpenCV high-level functions, demo codes including facial recognition, motion detection, color tracking, and more. Reserved extension interface for secondary development, along with user manual and secondary development documents.SpecificationsGeneral: 1. Product name: WAVEGO high-DOF bionic quadruped robot 2. Stand up: length 218mm, width 116mm, height 152mm 3. Lie down: length 228mm, width 116mm, height 127mm 4. Overall weight: 554g (with batteries) 5. DOF: 12 overall, 3 per single leg Operating system: Demo code: FreeRTOS + Raspberry Pi OS Motion performance: 1. Available gait: Shake hands, stand up, crouch slowly, diagonal gait , jump, self-balancing 2. Motion extension: Providing motion programming example, including flexible Bezier curve speed motion function 3. Load: 200g Servo info.: 1. Dimensions: 23.2 x12.1 x25.25 mm 2. Weight: 13.0 +/- 1g 3. Operating voltage: 6V 4. Idle speed: 0.1sec/60 degree (100RPM) 5. Stalling torque: 2.3kg.cm (31.99oz.in) 6. Rated load: 0.7kg.cm 7. Rated current: 350mA 8. Control method: Pulse width modification 9. Control system type: Digital comparator Visual function: 1. FreeRTOS demo: Web-based real time video streaming 2. Raspberry Pi OS demo: Real time video streaming, facial recognition, color tracking, moving object detection Note: All the demo codes are open sourced, the Raspberry Pi OS demo is based on open source projects flask-streaming and OpenCV Processor and memory: 1. ESP32 sub controller: Processor: Xtensa LX6 dual-core processor 240MHz 2. SRAM: 520KB+8MB 3. Flash: 448KB+4MB Others: 1. WiFi standard: 802.11b/g/n 2. Bluetooth standard: Bluetooth 4.2, including traditional Bluetooth (BR/EDR) and Bluetooth low energy (BLE) 3. External port: 2 x 5P multi-function extension port (host controller communication, power supply selection, assembly mode selection, etc.) 4. DC battery charger jack: Type-C (download, UART communication, peripheral expansion) Power supply: 1. Battery type: 18650 Li-ion batteries (NOT included) 2. Supply voltage: 7-8.4V 3. Recharge voltage: 8.4V 4. Protection: Over charge, discharge protection, over current protection, short circuit protection, reverse proof, equalizing charge, stable and safe operating 5. Output voltage: provides 5V output for other host controllerPackage List1. WAVEGO body case x 1 2. WAVEGO basic parts x 1 3. Semi-transparent acrylic panel x 1 4. Double-sided sticker x 1 5. WAVEGO base board x 1 6. 2MP camera x 1 7. 2.4G antenna x 1 8. 0.91inch OLED display x 1 9. Micro thrust bearing x 14 10. Micro ball flange bearing x 30 11. USB cable (~1m) x 1 12. Plus screwdriver x 1 13. Cross wrench sleeve x 1 14. IPEX 1 to SMA cable (~17cm) x 1 15. Jumper wire (~20cm) x 4 16. 4 PIN PH2.0 cable x 1 17. Servo pack x 1 18. 8.4V 2A battery charger x 1 19. Screws and standoffs x 1

Read more less

Features1. PoE UPS Base For CM4: Uninterruptible power supply, powering the CM4 while recharging 2. Connecting With Compute Module 4: Standard CM4 socket and color-coded Raspberry Pi 40PIN GPIO header. Suitable For Compute Module 4 Lite/EMMC Series Module 3. Uninterruptible Power: It is able to charge the batteries and provide power output for the system at the same time from external power supply. Automatically switch over to batteries output if external power supply is unavailable, keeps the system running without any trouble 4. Multi Power Supply Options: - Three external power supply options: USB interface, wide voltage DC, and PoE - When connected to the external power supply, the system will be powered and the battery will be charged at the same time, and the battery will be in a disconnected status after being fully charged, so as to avoid battery life damaging caused by frequently charging and discharging - When the external power supply is insufficient, the battery will provide power output together with the external power supply at the same time to ensure system normal operation - When the external power supply is connected, the system will keep running normally even when the battery fails or is taken out. When the external power supply is disconnected, it will automatically switch over to batteries output without interrupting the system operation 5. Safe And Stable Circuit Design: Protection circuits for over charge/discharge, over current, short circuit, and reverse-proof along with the standalone resettable fuse for each battery, more safe and stable 6. Real Time Monitoring: Monitoring the batteries voltage, current, power, and remaining capacity via I2C. (When the voltage dips too low, it is possible to save files properly and then shutdown the system by software, to avoid any data loss) Note: The 18650 batteries are not includedSpecifications1. CM4 socket: Suitable for all variants of Compute Module 4 2. Battery support: Parallel 18650 Li-ion battery x 3 (NOT included) 3. Networking: Gigabit Ethernet RJ45 connector, integrates 802.3af-compliant PoE circuit (5V/2.5A) 4. USB: USB 2.0 Type A ?? 4 5. Connector: - Raspberry Pi 40PIN GPIO header - M.2 M KEY slot, for connecting NVME SSD, or communication module with PCIE M.2 M KEY interface 6. Display: MIPI DSI port x 1 (22pin 0.5mm FPC connector) 7. Camera: MIPI CSI-2 port x 2 (22pin 0.5mm FPC connector) 8. Video: HDMI x 2, supports 4K 30fps output 9. RTC: Real-time clock with battery socket and ability to wake Compute Module 4 10. Storage: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 11. Fan: Allows speed adjustment and measurement, 5V / 12V 12. Indicator: - M.2 status LED - CM4 status LED 13. Power input7-36V 14. Dimensions: 175.0 x 108.0mm

Read more less

1. Interface compatible: RS-485, RS-232 standard2. Material: ABS3. Working mode: asynchronous half-duplex differential transmission4. Protection level: 600W lightning surge protection per line of RS-485 interface5. Transmission medium: twisted pair or shielded wire6. Transmission distance: RS-485 is less than 1200m, RS-232 is within 15m7. Transmission rate: 300-115.2kbps8. Communication mode: point-to-point/two-wire half-duplex, point-to-multipoint/two-wire half-duplex9. Scope of application: suitable for PC, terminal equipment, industrial control, digital instrument acquisition, multi-serial port equipment, serial interface of single-chip microcomputer, etc.10. Dimensions: about 51.8 x 17.8 x 35.7mm11. Weight: about 40gFeatures:1. 9-hole nickel-plated female head, wear-resistant and durable, anti-oxidation and anti-corrosion2. Twisted pair/shielded wire can be used to improve signal conversion and transmission anti-interference3. ABS material, lightning protection design4. Built-in zero-delay automatic transceiver conversion device, which automatically controls the direction of data flow through the I/O circuit5. Built-in fast voltage suppression protector TVS, non-optical isolation6. Bidirectional transmission, compatible with RS-485, RS-232 standard interfaces7. Two communication methods, stable transmission, convenient and fast

Read more less

1. Onboard standard CM4 connector, support access to CM4 Lite / eMMc series boards with Quad Core Cortex A72 64-bit processor, more powerful performance 2. Easily compatible with the interfaces of Raspberry Pi 3B / 3B+ boards 3. Onboard headphone jack (extended from USB) 4. Onboard 4-ch USB ports, compatible with USB 2.0 / 1.1 transmission 5. Onboard RJ45 Gigabit Ethernet port, 10 / 100 / 1000 M adaptive 6. Onboard PoE header, for connecting PoE HATs

Read more less

1. Using pogo pin connection, the Zero 2W can be easily attached 2. Easily compatible with the interfaces of Raspberry Pi 3B / 3B+ boards 3. Onboard headphone jack(extended from USB) and an additional speaker header 4. Onboard 4-ch USB ports, compatible with USB 2.0 / 1.1 transmission 5. Onboard RTL8152B Ethernet chip, support 1-ch RJ45 Ethernet port, 10 / 100 M adaptive 6. Not compatible with the first generation Zero Package List: 1. Zero-to-Pi3-Adapter (B) x 1 2. HD-MI Adapter x 1

Read more less

FeaturesBy nightfall, the dazzling neon lights of the streets and alleys illuminate the whole city making it more dynamic. Obviously, the Full-Color LED Matrix Panel is playing an important role. Maybe be on the doors of shops, maybe be on the bus or the taxi, you can always see animations or advertisement videos. Does it look cool? Why not have a try? 1. 4096 individual RGB LEDs, full-color display, adjustable brightness 2. 64 x 64 pixels, 3mm pitch, allows displaying text, colorful image, or animation 3. 192 x 192mm dimensions, moderate size, suitable for DIY desktop display or wall mount display 4. Onboard two HUB75 header, one for controller data input, one for output, chain support 5. Provides open source development resources and tutorials, for use with Raspberry Pi, Arduino, and so onSpecifications1. Dimensions: 192mm x 192mm 2. Pixels: 64 x 64=4096 dots 3. Spacing: 3mm 4. Pixel form: 1R1G1B 5. Viewing angle: greater than or equal to 160 degrees 6. Control Type: Synchronous 7. Driving: 1/32 scan 8. Connector: HUB75 9. Power supply: 5V / 4A (VH4 connector input) 10. Power: less than or equal to 20WPackage List1. RGB-Matrix-P3-64x64 LED matrix and accessories x 1 2. Power supply terminal adapter x 1 3. 16P wire about 30cm x 1

Read more less

1. Zero can be easily attached via specially designed connectors 2. Easily compatible with the interfaces of Raspberry Pi 3B / 3B+ boards 3. The same GPIO header height as 3B, easily connecting with 3B series HATs or development projects 4. Onboard 4-ch USB ports, compatible with USB 2.0 / 1.1 transmission 5. Onboard RTL8152B Ethernet chip, support 1-ch RJ45 Ethernet port, 10 / 100 M adaptive

Read more less