Bestselling Products

Features:1. Using double contact technology, the contact is more stable;2. The seat shell is made of special engineering plastic, which has high strength and long life;3. The shrapnel adopts imported beryllium copper material, which has low impedance and good elasticity;4. Thick gold-plated layer, thick electroplating of contacts, ultra-low contact impedance and high reliability; Product performance:1. Material: insulator PEI, PPS; shrapnel, beryllium copper Be Cu Gold plating (30u), Over Nickel plating (50u)2. Insulation resistance: 1000mohm, At DC 500V3. Withstand voltage: 700AC/1Minute4. Contact impedance: less than 25mohm5. PIN foot elasticity: 55g/PIN(Normal)6. Working temperature: minus 65-155 degrees Celsius7. Specifications and dimensions: pin spacing: 0.65 mm, pin position: 8, adaptable chip body width: 4.4 mm

Read more less

1. Type: Test Block2. Working frequency: Low frequency3. Application: Integrated Circuit IC4. Contact impedance: Less than 25 milliohms5. Number of cores: 306. Service life: 100,000 times7. Contact material: Beryllium copper shrapnel8. Insulator material: PEI, PPS9. Pin spacing: 0.65mm10. Working temperature: -65～155 degrees Celsius11. Adapter chip body width: 10.64x7.8mmFeatures:1. Using double contact technology, the contact is more stable2. The seat shell is made of special engineering plastic, which has high strength and long life.3. The shrapnel adopts imported beryllium copper material, which has low impedance and good elasticity4. Thick gold plating layer, thick contact plating, ultra-low contact impedance, high reliability

Read more less

OverviewCore103V is a small STM32 development board that features an STM32F103VET6 device as the microcontroller, supports further expansion. It is ideal for starting application development with STM32F family.As a minimal ready-to-run system, the Core103V integrates USB communication interface, JTAG/SWD programming/debugging interface, clock circuit, boot mode selection, and so on.Furthermore, pin headers on the backside allow the Core103V to be plugged-in your application board and act as the MCU core circuit in your system. All the I/O ports are accessible on the pin headers, and the header pitch is designed as 2.54mm.What is On BoardSTM32F103VET6 development board on board resource1. STM32F103VET6: The high performance STM32 MCU which features:- Core: Cortex-M3 32-bit RISC- Operating Frequency: 72MHz, 1.25 DMIPS/MHz- Operating Voltage: 2-3.6V- Package: LQFP100- I/Os: 80- Memories: 512kB Flash, 64kB RAM- MCU communication Interfaces:-- 3 x SPI, 5 x USART, 2 x I2S, 2 x I2C, 1 x FSMC, 1 x LCD, 1 x SDIO, 1 x USB, 1 x CAN- AD & DA converters: 3 x AD (12-bit, 1μs, shares 16 channels); 2 x DA (12-bit)- Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP2. AMS1117-3.3 (on bottom side): 3.3V voltage regulator3. Power supply switch, powered from 5Vin or USB connection4. Boot mode selection, for configuring BOOT0 pin5. Boot mode selection (on bottom side), for configuring BOOT1 pin6. Power indicator7. VBUS LED8. Reset button9. 8M crystal oscillator10. 32.768K crystal (on bottom side), for internal RTC with calibration11. JTAG/SWD interface: for debugging/programming12. USB connector, used for establishing USB communication between PC and the STM32 development board13. IO expander (including VCC/GND), all the I/O pins are accessible on expansion connectors for further expansion14. 5V in pinheader, 5V power supply input15. USB enable jumper- Short the jumper to enable USB function- Open the jumper to disable, as well as taking up no I/O port16. VBAT selection jumper- Short the jumper to use system power supply- Open the jumper to connect the VBAT to external power, such as battery17. VREF selection jumper- Short the jumper to connect VREF+/VREF- to VCC/GND- Open the jumper to connect VREF+/VREF- to other custom pin via jumper wirePackage Contents1. Core103V development board x 12. USB type A to Mini-B cable x 13. Software CD x 1

Read more less

Overview1. XCore407I is an STM32 MCU core board that features the STM32F407IGT6 on board.2. Clock circuit, USB power management3. Onboard devices: USB HS PHY, Ethernet PHY, 1G Bit NandFlash4. Connectors：USB HS (mini / type A), USB FS (mini), Ethernet (RJ45)5. All the idle I/O ports are accessible on the pin headers6. 2.0mm pin header pitch, smaller size, easier to integrate into user system7. Note : please consider the EVK407I, which supports easily programing/debugging.What is On BoardSTM32F407IGT6 development board on board resource1. STM32F407IGT6: The high performance STM32 MCU which features:- Core: Cortex-M4 32-bit RISC- Feature: a full set of single-cycle DSP instructions- Operating Frequency: 168MHz, 210 DMIPS/1.25 DMIPS/MHz- Operating Voltage: 1.8V-3.6V- Package: LQFP176- Memories: 1024kB Flash, 192+4kB SRAM- MCU communication Interfaces:-- 3 x SPI, 4 x USART, 2 x UART, 2 x I2S, 3 x I2C-- 1 x FSMC, 1 x SDIO, 2 x CAN-- 1 x USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, ULPI and on-chip full-speed PHY-- 1 x 10/100 Ethernet MAC-- 1 x 8 to 14-bit parallel camera interface- AD & DA converters: 3 x AD (12-bit, 1μs, shares 24 channels); 2 x DA (12-bit)- Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP2. MIC2075-2, onboard USB FS power management device3. AMS1117-3.3, 3.3V voltage regulator4. K9F1G08U0E, 1G Bit NandFlash5. DP83848, Ethernet PHY6. MIC2075-1, onboard USB HS power management device7. USB3300, USB HS PHY8. Power supply switch, powered from 5Vin or USB connection9. Boot mode switch, for configuring BOOT0 pin10. Power indicator11. USB FS LED12. USB HS LED13. Reset button14. 8M crystal, MCU clock, enables the MCU run at higher speed by frequency multiplication15. 24M crystal, USB3300 clock16. 50M crystal, DP83848 clock17. 32.768K crystal, for internal RTC with calibration18. Ethernet connector19. USB FS mini connector20. USB HS mini connector21. USB HS type A connector22. MCU pins expander, VCC, GND and all the idle I/O ports are accessible on expansion connectors for further expansion23. USB OTG/HOST jumper24. VREF/VBAT jumper25. Ethernet I/O selection solder joint26. USB HS I/O selection solder joint27. PDR selection solder joint: 1.8-3.6V, -40～105℃ OR 1.7-3.6V, 0～70℃Package Contents1. XCore407I development board x 12. USB type A to Mini-B cable x 13. Software CD x 1

Read more less

Overview1. Core407I is a small STM32 development board that features an STM32F407IGT6 device as the microcontroller, supports further expansion. It is ideal for starting application development with STM32F family.2. As a minimal ready-to-run system, the Core407I integrates USB communication interface, JTAG/SWD programming/debugging interface, clock circuit, USB power management, boot mode selection, and so on.3. Furthermore, pin headers on the backside allow the Core407I to be plugged-in your application board and act as the MCU core circuit in your system. All the I/O ports are accessible on the pin headers, and the header pitch is designed as 2.0mm to achieve smaller pcb size.What is On BoardSTM32F407IGT6 development board on board resource1. STM32F407IGT6: The high performance STM32 MCU which features:- Core: Cortex-M4 32-bit RISC- Feature: a full set of single-cycle DSP instructions- Operating Frequency: 168MHz, 210 DMIPS/1.25 DMIPS/MHz- Operating Voltage: 1.8V-3.6V- Package: LQFP176- Memories: 1024kB Flash, 192+4kB SRAM- MCU communication Interfaces:-- 3 x SPI, 4 x USART, 2 x UART, 2 x I2S, 3 x I2C-- 1 x FSMC, 1 x SDIO, 2 x CAN-- 1 x USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, ULPI and on-chip full-speed PHY-- 1 x 10/100 Ethernet MAC-- 1 x 8 to 14-bit parallel camera interface- AD & DA converters: 3 x AD (12-bit, 1μs, shares 24 channels); 2 x DA (12-bit)- Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP2. AMS1117-3.3 (on bottom side), 3.3V voltage regulator3. MIC2075 (on bottom side), onboard USB power management device4. Power supply switch, powered from 5V in or USB connection5. Boot mode switch, for configuring BOOT0 pin6. Power indicator7. VBUS LED8. Reset button9. 8M crystal oscillator (on bottom side)10. 32.768K crystal (on bottom side), for internal RTC with calibration11. JTAG/SWD interface: for debugging/programming12. USB interface- As DEVICE, used for establishing USB communication between PC and the STM32 development board- As HOST, connecting to USB devices such as USB flash drive through a USB OTG cable13. MCU pins expander, VCC, GND and all the I/O ports are accessible on expansion connectors for further expansion14. 5V in pinheader, 5V power supply is required when using USB HOST/OTG15. USB HOST/OTG jumper- Short the jumper when using USB HOST/OTG- Open the jumper to disconnect from I/O port16. VBAT selection jumper- Short the jumper to use system power supply- Open the jumper to connect the VBAT to external power, such as battery17. VREF selection jumper- Short the jumper to connect VREF+ to VCC- Open the jumper to connect VREF+ to other custom pin via jumper wirePackage Contents1. Core407I development board x 12. USB type A to Mini-B cable x 13. Software CD x 1

Read more less

Overview1. Core407V is a small STM32 development board that features an STM32F407VET6 device as the microcontroller, supports further expansion. It is ideal for starting application development with STM32F family.2. As a minimal ready-to-run system, the Core407V integrates USB communication interface, JTAG/SWD programming/debugging interface, clock circuit, USB power management, boot mode selection, and so on.3. Furthermore, pin headers on the backside allow the Core407V to be plugged-in your application board and act as the MCU core circuit in your system. All the I/O ports are accessible on the pin headers, and the header pitch is designed as 2.54mm.What has On Board1. STM32F407VET6: The high performance STM32 MCU which features:- Core: Cortex-M4 32-bit RISC- Feature: a full set of single-cycle DSP instructions- Operating Frequency: 168MHz, 210 DMIPS/1.25 DMIPS/MHz- Operating Voltage: 1.8V-3.6V- Package: LQFP100- Memories: 512kB Flash, 192+4kB SRAM- MCU communication Interfaces:-- 3 x SPI, 3 x USART, 2 x UART, 2 x I2S, 3 x I2C-- 1 x FSMC, 1 x SDIO, 2 x CAN-- 1 x USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, ULPI and on-chip full-speed PHY-- 1 x 10/100 Ethernet MAC-- 1 x 8 to 12-bit parallel camera interface- AD & DA converters: 3 x AD (12-bit, 1μs, shares 24 channels); 2 x DA (12-bit)- Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP2. AMS1117-3.3 (on bottom side): 3.3V voltage regulator3. MIC2075 (on bottom side): onboard USB power management device4. Power supply switch, powered from 5Vin or USB connection5. Boot mode switch, for configuring BOOT0 pin6. Power indicator7. Reset button8. 8M crystal oscillator9. 32.768K crystal (on bottom side), for internal RTC with calibration10. JTAG/SWD interface: for debugging/programming11. USB connector, used for establishing USB communication between PC and the STM32 development board12. IO expander (including VCC/GND), all the MCU pins are accessible on expansion connectors for further expansion13. 5Vin pinheader, 5V power supply is required when using USB HOST/OTG14. USB jumper- Short the jumper when using USB- Open the jumper to disconnect from I/O ports15. VBAT selection jumper- Short the jumper to use system power supply- Open the jumper to connect the VBAT to external power, such as battery16. VREF selection jumper- Short the jumper to connect VREF+/VREF- to VCC/GND- Open the jumper to connect VREF+/VREF- to other custom pin via jumper wirePackage Contents1. Core407V development board x 12. USB type A to Mini-B cable x 13. Software CD x 1

Read more less

Overview1. Core405R is an STM32 MCU core board designed for STM32F405RGT6, supports further expansion. It is ideal for starting application development with STM32F family.2. Minimal ready-to-run system, integrates clock circuit, USB control circuit, USB connector, 3. etc.3. All the I/O ports are accessible on the pin headers4. JTAG/SWD programming/debugging interface5. 2.54mm header pitch, allowed to be plugged-in your application boardWhat has On Board1. STM32F405RGT6: The high performance STM32 MCU which features:- Core: Cortex-M4 32-bit RISC- Operating Frequency: 168MHz, 210 DMIPS/1.25 DMIPS/MHz- Operating Voltage: 1.8V-3.6V- Package: LQFP64- Memories: 1MB Flash, 192+4kB SRAM- MCU communication Interfaces:-- 3 x SPI, 4 x USART, 2 x UART, 2 x I2S, 3 x I2C, 1 x SDIO, 2 x CAN--1 x USB 2.0 HS/FS device/host/OTG controller with dedicated DMA, on-chip full-speed PHY--1 x USB HS ULPI (external PHY required)- AD & DA converters: 3 x AD (12-bit, 1μs, shares 16 channels); 2 x DA (12-bit)- Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP2. AMS1117-3.3: 3.3V voltage regulator3. MIC2075-2: onboard USB power management device4. Power supply switch, powered from 5Vin or USB connection5. Boot mode selection, for configuring BOOT0 pin6. Power indicator7. VBUS LED8. Reset button9. 8M crystal10. 32.768K crystal, for internal RTC with calibration11. JTAG/SWD interface: for debugging/programming12. USB connector, used for establishing USB communication between PC and the STM32 development board13. MCU pins expander, VCC, GND and all the I/O pins are accessible on expansion connectors for further expansion14. 5Vin pinheader, 5V power supply is required when using USB HOST/OTG15. USB jumper- Short the jumper when using USB- Open the jumper to disconnect from related I/O port16. VBAT selection jumper- Short the jumper to use system power supply- Open the jumper to connect the VBAT to external power, such as batteryPackage Contents1. Core405R x 12. USB type A to Mini-B cable x 13. Software CD x 1

Read more less

STM32 development board designed for STM32F429I, features the STM32F429IGT6 MCU, and integrates various standard interfaces, pretty easy for peripheral expansions.Overview1. Open429I-C is an STM32 development board designed for the STM32F429IGT6 microcontroller, consists of the mother board and the MCU core board Core429I.2. The Open429I-C supports further expansion with various optional accessory boards for specific application. The modular and open design makes it the ideal for starting application development with STM32 series microcontrollers.What has on the mother board1. MCU core board connector: for easily connecting the Core429I2. USART3 interface: easily connects to RS232, RS485, USB TO 232, etc.3. DCMI interface: for connecting camera4. Capacitive touch panel interface: for connecting capacitive touch panel5. CAN2 interface: for connecting CAN modules6. CAN1 interface: for connecting CAN modules7. SDIO interface: for connecting Micro SD module, features much faster access speed rather than SPI8. ULPI interface: for connecting high-speed USB peripheral (the STM32F429I integrates USB HS controller without any PHY device)9. LCD interface 1: for connecting 7inch LCD10. ONE-WIRE interface: easily connects to ONE-WIRE devices (TO-92 package), such as temperature sensor (DS18B20), electronic registration number (DS2401), etc.11. LCD interface 2: for connecting 4.3inch LCD12. I2C2/I2C3 interface: easily connects to I2C peripherals such as I/O expander (PCF8574), EEPROM (AT24Cxx), etc.13. SAI1 interface: for connecting audio modules like UDA1380 module14. Ethernet interface: for connecting Ethernet modules15. USB connector: USB to UART via the onboard convertor PL230316. SPI1/SPI2 interfaces:- Easily connects to SPI peripherals such as DataFlash (AT45DBxx), SD card, MP3 module, etc.- Easily connects to AD/DA modules (SPI1 features AD/DA alternative function)17. I2S2/I2S3/I2C1 interface: easily connects to I2S peripherals such as audio module, etc.18. 8-bit FMC interface: easily connects to peripherals such as NandFlash19. 5V DC jack20. 5V/3.3V power input/output: usually used as power output, also common-grounding with other user board21. MCU pins connector: all the MCU I/O ports are accessible on expansion connectors for further expansion22. PL2303: USB to UART convertor23. LEDs: convenient for indicating I/O status and/or program running state24. PL2303 TX-LED / RX-LED25. 12MHz crystal: for PL230326. Joystick: five positions27. WAKE UP button: used as regular button, and/or wake up the STM32 MCU from sleep28. USB to UART jumper29. LED jumper- Short the jumper to connect to default I/Os used in example code- Open the jumper to connect to custom I/Os via jumper wires30. Button/Joystick jumper- Short the jumper to connect to default I/Os used in example code- Open the jumper to connect to custom I/Os via jumper wiresPackage Contains1. Open429I-C development board x 12. USB type A plug to mini-B plug cable x 13. USB type A receptacle to mini-B plug cable x 14. 4-pin 2-pin wires pack x 15. USB power cable x 16. Software CD x 1

Read more less

Overview1. Open429I-C is an STM32 development board designed for the STM32F429IGT6 microcontroller, consists of the mother board and the MCU core board Core429I.2. The Open429I-C supports further expansion with various optional accessory boards for specific application. The modular and open design makes it the ideal for starting application development with STM32 series microcontrollers.What has on the mother board1. MCU core board connector: for easily connecting the Core429I2. USART3 interface: easily connects to RS232, RS485, USB TO 232, etc.3. DCMI interface: for connecting camera4. Capacitive touch panel interface: for connecting capacitive touch panel5. CAN2 interface: for connecting CAN modules6. CAN1 interface: for connecting CAN modules7. SDIO interface: for connecting Micro SD module, features much faster access speed rather than SPI8. ULPI interface: for connecting high-speed USB peripheral (the 9. STM32F429I integrates USB HS controller without any PHY device)10. LCD interface 1: for connecting 7inch LCD11. ONE-WIRE interface: easily connects to ONE-WIRE devices (TO-92 package), such as temperature sensor (DS18B20), electronic registration number (DS2401), etc.12. LCD interface 2: for connecting 4.3inch LCD13. I2C2/I2C3 interface: easily connects to I2C peripherals such as I/O expander (PCF8574), EEPROM (AT24Cxx), etc.14. SAI1 interface: for connecting audio modules like UDA1380 module15. Ethernet interface: for connecting Ethernet modules16. USB connector: USB to UART via the onboard convertor PL2303SPI1/SPI2 interfaces:- Easily connects to SPI peripherals such as DataFlash (AT45DBxx), SD card, MP3 module, etc.- Easily connects to AD/DA modules (SPI1 features AD/DA alternative function)17. I2S2/I2S3/I2C1 interface: easily connects to I2S peripherals such as audio module, etc.18. 8-bit FMC interface: easily connects to peripherals such as NandFlash19. 5V DC jack20. 5V/3.3V power input/output: usually used as power output, also common-grounding with other user board21. MCU pins connector: all the MCU I/O ports are accessible on expansion connectors for further expansion22. PL2303: USB to UART convertor23. LEDs: convenient for indicating I/O status and/or program running state24. PL2303 TX-LED / RX-LED25. 12MHz crystal: for PL230326. Joystick: five positions27. WAKE UP button: used as regular button, and/or wake up the STM32 MCU from sleep28. USB to UART jumper29. LED jumper- Short the jumper to connect to default I/Os used in example code- Open the jumper to connect to custom I/Os via jumper wires30. Button/Joystick jumper- Short the jumper to connect to default I/Os used in example code- Open the jumper to connect to custom I/Os via jumper wiresThe "Standard Package" and "Accessory Boards Package" below are included.Standard Package1. Open429I-C development board x 12. USB type A plug to mini-B plug cable x 13. USB type A receptacle to mini-B plug cable x 14. 4-pin 2-pin wires pack x 15. USB power cable x 16. Software CD x 1Accessory Boards Package1. 4.3 inch 480x272 Touch LCD (B) x 12. DP83848 Ethernet Board x 13. USB3300 USB HS Board x 14. NandFlash Board (A) x 15. UDA1380 Board x 16. Micro SD Storage Board x 17. OV2640 Camera Board x 18. Ethernet Cable x 19. 4.3 inch LCD screws pack x 1

Read more less

NUCLEO-L476RG DescriptionThe STM32 Nucleo board provides an affordable and flexible way for users to try out new ideas and build prototypes with any STM32 microcontroller line, choosing from the various combinations of performance, power consumption and features. The Arduino™ connectivity support and ST Morpho headers make it easy to expand the functionality of the STM32 Nucleo open development platform with a wide choice of specialized shields.The STM32 Nucleo board does not require any separate probe as it integrates the ST-LINK/V2-1 debugger and programmer.The STM32 Nucleo board comes with the STM32 comprehensive software HAL library together with various packaged software examples, as well as direct access to mbed online resources.NUCLEO-L476RG Key FeaturesSTM32 microcontroller with LQFP64 packageTwo types of extension resourcesArduino Uno Revision 3 connectivitySTMicroelectronics Morpho extension pin headers for full access to all STM32 I/Osmbed-enabled (http://mbed.org)On-board ST-LINK/V2-1 debugger/programmer with SWD connectorselection-mode switch to use the kit as a standalone ST-LINK/V2-1Flexible board power supplyUSB VBUS or external source(3.3 V, 5 V, 7 - 12 V)Power management access pointThree LEDsUSB communication (LD1), user LED (LD2), power LED (LD3)Two push buttons: USER and RESETUSB re-enumeration capability: three different interfaces supported on USBVirtual Com portMass storageDebug portSupported by wide choice of Integrated Development Environments (IDEs) including IAR™, Keil®, GCC-based IDEs

Read more less

Overview1. Infrared detection, eliminating the interferences of external stray light2. Schmitt trigger, stable wave form and signals3. Signal output indicator (while breaking the beam, outputs low level, the indicator lights up)Specifications1. Power: 3.3V ~ 5V2. Dimension: 26.8mm × 15mm × 18.7mm3. Mounting holes size: 3mm4. Gap width: 6mmApplications- Motor speed detection- Pulse counterHow to UseIn the case of working with a MCU:- VCC ↔ 3.3V ~ 5V- GND ↔ GND- DOUT ↔ MCU.IO (digital output)

Read more less

OverviewThis AlphaBot2 robot kit is designed to use with Raspberry Pi 3 Model B (not included). It features rich common robot functions including line tracking, obstacle avoiding, Bluetooth/infrared/WiFi remote control, video monitoring, etc.Thanks to the highly integrated modular design, it is fairly easy to assemble by a snap, no soldering, no wiring. After a few minutes spent on hardware assembing, youre almost there, our open source demo codes is ready to help you get started fast.AlphaBot2 FeaturesAlphaBot2 employs a 2-layer structure to provide excellent stability and compatibility.AlphaBot2-Base, the lower base chassis:1. 5-ch infrared sensor, analog output, combined with PID algorithm, stable line tracking2. Onboard modules like line tracking, obstacle avoiding, needs no messy wiring3. TB6612FNG dual H-bridge motor driver, compared with L298P, its more efficient, more compact, and less heating4. 5Onboard RGB LEDs, true color lighting, pretty coolAlphaBot2-Pi, the upper adapter board for controller:1. LM2596 voltage regulator, provides the Pi with stable 5V power2. TLC1543 AD acquisition chip, allows the Pi to use analog sensors3. PCA9685 servo controller, make it more smoothly to rotate the pan head4. CP2102 UART converter, easy for controlling the Pi via UART

Read more less

OverviewSmart robot is always the favorite project of electronic enthusiasts, however, a robot will be "not that smart" if it is not AI-based.Welcome the JetBot, an actual smart robot powered by Jetson Nano. With the intelligent eye (front camera), facial recognition, object tracking, auto line following, and collision avoidance can be easily achieved. It also comes with ROS nodes code, which makes it easy to get started with the open source ROS (Robot Operating System), and to learn the system framework and concepts of ROS.Features1. Adopts 3x 18650 batteries (NOT included), high battery capacity, up to 12.6V voltage output, more powerful driving force.2. Integrates S-8254AA + AO4407A lithium battery protection circuit, provides protections for over-charge, over-discharge, over-current, and short circuit.3. Onboard APW7313 voltage regulator, provides stable 5V voltage for the Jetson Nano.4. Onboard TB6612FNG dual H-bridge motor driver.5. Onboard 0.91inch 128×32 pixels OLED, allows to display robot IP address, RAM, battery life, etc.6. Onboard ADS1115 AD acquisition chip for monitoring the battery in real time.7. Weight: 1029gWhat is on the JetBot Expansion Board1. S-8254AA: Lithium battery protector, provides protections for over-charge, over-discharge, over-current, and short circuit2. ADS1115: 16-bit AD acquisition chip, monitoring the battery in real time3. AO4407A: P-Channel MOSFET for protection circuit4. APW7313: 5V power regulator for powering the Jetson Nano5. PCA9685: PWM controller, I2C interface, for IO expansion6. TB6612FNG: dual H-bridge motor driver7. 0.91 inch OLED: SSD1306 driver chip, 128×32 pixels8. Battery charger input: charging the 3x 18650 batteries9. Power switch10. 18650 battery holder11. Motor connector (bottom side)12. Jetson Nano communication header: I2C interface and power supplyPacking List1. Jetson Nano Developer Kit x12. Micro SD Card 64GB ×13. Metal box x14. Camera holder x15.Acrylic piece x16. Jetbot expansion board x17. IMX219-160 Camera x18. Wireless-AC8265 x19. Motor 2PCS x110. Wheel 2PCS x111.Omni-direction wheel 2PCS x112. Power adapter EU head x113. 12.6V battery charger x114. Wireless gamepad x115. Screwdriver 2PCS x116. 6Pin 9cm cable x117. Screws pack x118. Spanner x119. Cooling fan x120. Micro SD card reader x1

Read more less

OverviewThis AlphaBot2 robot kit is designed to use with an Arduino compatible controller (not included). It features rich common robot functions including line tracking, obstacle avoiding, ultrasonic ranging, infrared remote control, Bluetooth communication, etc.Thanks to the highly integrated modular design, it is fairly easy to assemble by a snap, no soldering, no wiring. After a few minutes spent on hardware assembing, you're almost there, our open source demo codes is ready to help you get started fast.AlphaBot2 FeaturesAlphaBot2 employs a 2-layer structure to provide excellent stability and compatibility.AlphaBot2-Base, the lower base chassis:1. 5-ch infrared sensor, analog output, combined with PID algorithm, stable line tracking2. Onboard modules like line tracking, obstacle avoiding, needs no messy wiring3. TB6612FNG dual H-bridge motor driver, compared with L298P, it's more efficient, more compact, and less heating4. N20 micro gear motor, with metal gears, low noise, high accuracy5. Onboard RGB LEDs, true color lighting, pretty coolAlphaBot2-Ar, the upper adapter board for controller:1. Onboard Arduino interface, into which Arduino controller can be directly plugged2. 0.96inch 128x64 yellow/blue dual color OLED3. TLC1543 AD acquisition chip4. PC8574 I/O expander, avoid I/O shortage5. Xbee connector, for connecting dual-mode Bluetooth modulePackage Contents1. AlphaBot2-Ar (adapter board) x12. AlphaBot2-Base (base chassis) x13. Ultrasonic sensor x14. IR remote controller x15. FC-20P cable 8cm x16. USB type A plug to micro B plug cable x17. AlphaBot2-Ar screws x18. Screwdriver x1 (Extra Free)

Read more less

Specifications1. Product: MG90S Servo2. Torque: 2.0kg/cm(4.8V), 2.8kg/cm(6V)3. Speed: 0.11s/60°(4.8V), 0.09s/60°(6V)4. Rotate angle: 180°5. Operating voltage: 4.8 ~ 6V6. Gear: metal7. Dead band: 5us8. Weight: 12.2g9. Dimension: 22.8mm × 12.2mm × 28.5mm

Read more less

1. Product: MG996R Servo2. Torque: 9kg/cm(4.8V), 11kg/cm(6V)3. Speed: 0.19s/60°(4.8V), 0.18s/60°(6V)4. Rotate angle: 180°5. Operating voltage: 4.8 ~ 6V6. Gear: metal7. Dead band: 5us8. Weight: 55g9. Dimension: 40.7mm × 19.7mm × 42.9mm

Read more less

Overview1. This is a Raspberry Pi LoRa HAT based on SX1268, covers 470MHz frequency band. It allows data transmission up to 5km through serial port.2. By utilizing the new generation LoRa spread spectrum modulation technology, the communication distance of the module is as long as 5km, also supports auto repeating to transmit longer. Other features include Wake on Radio, wireless config, carrier sensing, communication key, and so on.3. Comparing with normal LoRa modules, the SX1268 LoRa HAT achieves longer communication distance, higher rate, lower consumption, better safety and anti-interference. It is suitable for various applications such as industrial control, smart home, data collection, etc.Features1. Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards2. Onboard CP2102 USB TO UART converter, for serial debugging3. Brings the UART control interface, for connecting host boards like Arduino/STM324. 4x LED indicators, easy to check the module status5. LoRa spread spectrum modulation technology, up to 84 available signal channel, longer communication distance, more robust to interference6. Auto multi-level repeating, suit for ultra long range communication, allows multi network on the same region7. Low power consumption features like deep sleeping and Wake on Radio, ideal for battery-powered applications8. Customizable communication key which won't be retrieved, greatly improves the security of user data9. Support LBT, monitoring the signal channel noise before transmitting, greatly improves the success ratio under extreme environment10. Support RSSI signal intensity indicating, for evaluating signal quality, tuning the network11. Support wireless parameter configuration, by sending wireless command/data packet, remotely configure or retrieve the module parameter12. Support fixed-point transmission, broadcast, signal channel monitor13. Come with development resources and manual (examples for Raspberry Pi/STM32)What is on Board1. SX1268 LoRa module2. 74HC125V: voltage level translator3. CP2102: USB TO UART converter4. Raspberry Pi GPIO connector: for connecting with Raspberry Pi5. USB TO UART port6. UART header: for connecting host boards like STM32/Arduino7. SMA antenna connector8. IPEX antenna connector9. Indicators:- RXD/TXD: UART RX/TX indicator- AUX: auxiliary indicator- PWR: power indicator10. UART selection jumpers- A: Control the LoRa module through USB TO UART- B: Control the LoRa module through Raspberry Pi- C: Access Raspberry Pi through USB TO UART11. LoRa mode selection jumpers- Short M0, short M1: Transmission mode- Short M0, open M1: Configuration mode- Open M0, short M1: WOR mode- Open M0, open M1: deep sleep modeSpecification1. RF module: SX12682. Frequency band: 410.125 ~ 493.125MHz3. Radio rate: 0.3kbps ~ 62.5kbps (programmable)4. Transmit power: 22.0dBm (10/13/17/22dBm programmable)5. Receive sensitivity: -147dBm (radio rate 2.4kbps)6. Power consumption: - Transmit current: 110mA (transient consumption)- Receive current: 11mA- Sleep current: 2uA (LoRa module software shutoff)7. Communication interface: UART (TTL level)8. Baudrate: 1200bps ~ 115200bps (9600bps by default)9. Packet length: 240 Byte (32/64/128/240 Byte programmable)10. Cache: 1000 Byte11. Experimental range: 5km (condition: cloudless and wild, altitude 2.5m, antenna gain 5dBi, radio rate 2.4kbps)12. Power supply: 5V13. Logic level: 3.3V/5V14. Operating temperature: -40~85 degree C15. Applications: Smart home, industrial sensors, building automation, smart meters, and more other IoT applications16. Dimensions: 7cm x 12cm x 2cm17. Weight: 69g18. Packing List:- SX1268 470M LoRa HAT x1- USB type A plug to micro plug cable x1- 470MHz antenna x1

Read more less

Overview1. This is a Pi LoRa HAT based on SX1262, covers 915MHz frequency band. It allows data transmission up to 5km through serial port.2. By utilizing the new generation LoRa spread spectrum modulation technology, the communication distance of the module is as long as 5km, also supports auto repeating to transmit longer. Other features include Wake on Radio, wireless config, carrier sensing, communication key, and so on.3. Comparing with normal LoRa modules, the SX1262 LoRa HAT achieves longer communication distance, higher rate, lower consumption, better safety and anti-interference. It is suitable for various applications such as industrial control, smart home, data collection, etc.Features1.Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards2. Onboard CP2102 USB TO UART converter, for serial debugging3. Bring the UART control interface, for connecting host boards like Arduino/STM324. 4x LED indicators, easy to check the module status5. LoRa spread spectrum modulation technology, up to 81 available signal channel, longer communication distance, more robust to interference6. Auto multi-level repeating, suit for ultra long range communication, allows multi network on the same region7. Low power consumption features like deep sleeping and Wake on Radio, ideal for battery-powered applications8. Customizable communication key which wont be retrieved, greatly improves the security of user data9. Support LBT, monitoring the signal channel noise before transmitting, greatly improves the success ratio under extreme environment10. Support RSSI signal intensity indicating, for evaluating signal quality, tuning the network11. Support wireless parameter configuration, by sending wireless command/data packet, remotely configure or retrieve the module parameter12. Support fixed-point transmission, broadcast, signal channel monitor13. Come with development resources and manual (examples for Raspberry Pi/STM32)What is on Board1. SX1262 LoRa module2. 74HC125V: voltage level translator3. CP2102: USB TO UART converter4. Raspberry Pi GPIO connector: for connecting with Raspberry Pi5. USB TO UART port6. UART header: for connecting host boards like STM32/Arduino7. SMA antenna connector8. IPEX antenna connector9. Indicators:- RXD/TXD: UART RX/TX indicator- AUX: auxiliary indicator- PWR: power indicator10. UART selection jumpers- A: Control the LoRa module through USB TO UART- B: Control the LoRa module through Raspberry Pi- C: Access Raspberry Pi through USB TO UART11. LoRa mode selection jumpers- Short M0, short M1: Transmission mode- Short M0, open M1: Configuration mode- Open M0, short M1: WOR mode- Open M0, open M1: deep sleep modeSpecification1. RF module: SX12622. Frequency band: 850.125 ~ 930.125MHz3. Radio rate: 0.3kbps ~ 62.5kbps (programmable)4. Transmit power: 22.0dBm (10/13/17/22dBm programmable)5. Receive sensitivity: -147dBm (radio rate 2.4kbps)6. Power consumption: - Transmit current: 133mA (transient consumption)- Receive current: 11mA- Sleep current: 2uA (LoRa module software shutoff)7. Communication interface: UART (TTL level)8. Baudrate: 1200bps ~ 115200bps (9600bps by default)9. Packet length: 240 Byte (32/64/128/240 Byte programmable)10. Cache: 1000 Byte11. Experimental range: 5km (condition: cloudless and wild, altitude 2.5m, antenna gain 5dBi, radio rate 2.4kbps)12. Power supply: 5V13. Logic level: 3.3V/5V14. Operating temperature: -40~85 degree C15. Applications: Smart home, industrial sensors, building automation, smart meters, and more other IoT applications16. Dimensions: 7cm x 12cm x 2cm17. Weight: 69g18. Packing List:- SX1262 915MHz LoRa HAT x1- USB type A plug to micro plug cable x1- 915MHz antenna x1

Read more less

Overview1. This is a Raspberry Pi LoRa HAT based on SX1268, covers 433MHz frequency band. It allows data transmission up to 5km through serial port.2. By utilizing the new generation LoRa spread spectrum modulation technology, the communication distance of the module is as long as 5km, also supports auto repeating to transmit longer. Other features include Wake on Radio, wireless config, carrier sensing, communication key, and so on.3. Comparing with normal LoRa modules, the SX1268 LoRa HAT achieves longer communication distance, higher rate, lower consumption, better safety and anti-interference. It is suitable for various applications such as industrial control, smart home, data collection, etc.Features1.Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards2. Onboard CP2102 USB TO UART converter, for serial debugging3. Bring the UART control interface, for connecting host boards like Arduino/STM324. 4x LED indicators, easy to check the module status5. LoRa spread spectrum modulation technology, up to 84 available signal channel, longer communication distance, more robust to interference6. Auto multi-level repeating, suit for ultra long range communication, allows multi network on the same region7. Low power consumption features like deep sleeping and Wake on Radio, ideal for battery-powered applications8. Customizable communication key which wont be retrieved, greatly improves the security of user data9. Support LBT, monitoring the signal channel noise before transmitting, greatly improves the success ratio under extreme environment10. Support RSSI signal intensity indicating, for evaluating signal quality, tuning the network11. Support wireless parameter configuration, by sending wireless command/data packet, remotely configure or retrieve the module parameter12. Support fixed-point transmission, broadcast, signal channel monitor13. Come with development resources and manual (examples for Raspberry Pi/STM32)What is on Board1. SX1268 LoRa module2. 74HC125V: voltage level translator3. CP2102: USB TO UART converter4. Raspberry Pi GPIO connector: for connecting with Raspberry Pi5. USB TO UART port6. UART header: for connecting host boards like STM32/Arduino7. SMA antenna connector8. IPEX antenna connector9. Indicators:- RXD/TXD: UART RX/TX indicator- AUX: auxiliary indicator- PWR: power indicator10. UART selection jumpers- A: Control the LoRa module through USB TO UART- B: Control the LoRa module through Raspberry Pi- C: Access Raspberry Pi through USB TO UART11. LoRa mode selection jumpers- Short M0, short M1: Transmission mode- Short M0, open M1: Configuration mode- Open M0, short M1: WOR mode- Open M0, open M1: deep sleep modeSpecification1. RF module: SX12682. Frequency band: 410.125 ~ 493.125MHz3. Radio rate: 0.3kbps ~ 62.5kbps (programmable)4. Transmit power: 22.0dBm (10/13/17/22dBm programmable)5. Receive sensitivity: -147dBm (radio rate 2.4kbps)6. Power consumption: - Transmit current: 110mA (transient consumption)- Receive current: 11mA- Sleep current: 2uA (LoRa module software shutoff)7. Communication interface: UART (TTL level)8. Baudrate: 1200bps ~ 115200bps (9600bps by default)9. Packet length: 240 Byte (32/64/128/240 Byte programmable)10. Cache: 1000 Byte11. Experimental range: 5km (condition: cloudless and wild, altitude 2.5m, antenna gain 5dBi, radio rate 2.4kbps)12. Power supply: 5V13. Logic level: 3.3V/5V14. Operating temperature: -40~85 degree C15. Applications: Smart home, industrial sensors, building automation, smart meters, and more other IoT applications16. Dimensions: 7cm x 12cm x 2cm17. Weight: 69g18. Packing List:- SX1268 433MHz LoRa HAT x1- USB type A plug to micro plug cable x1- 433MHz antenna x1

Read more less

Memory Card Type:SD CardScreen Type:LCD ScreenImage Stabilization:Electronic Image StabilizationSet Type:Zoom SetsModel Number:Digital CameraImage Resolution (Video):Full HD (1920x1080)Recording Format:Picture: JPEG Video: AVI1. CMOS sensor, up to 16 million pixels2. Storage media: expandable SD card / HCSD card to 32GB3. Sensitivity: automatic, ISO100, ISO200, ISO4004. Lens: fixed lens F/3.2, f=7.6mm5. Focus range: 1.2m - infinity6. Still image: JEPG/VGA, 1M, 3M, 5M, 12M, 16M (interpolation), movie clip AVI 1080P 720P VGA7.LED fill light: <1.0m range Open/close8. white balance: automatic / sunlight / cloudy / bulb / fluorescent9. Exposure compensation: -2.0/+2.010. Self-timer: Off / 2 seconds / 5 seconds / 10 seconds, automatic shutdown: off / 1/3 / 5 / 10 minutes11. Computer interface: USB2.0 (high speed)12. Microphone: Built-in, speaker: built-in13. LCD screen: 2.7-inch TFT-LCD (230,000 pixels, 4:3)14. Video output: NTSC/PAL15. Power supply: lithium ion battery BL-5C

Read more less

1. High resolution, adopt COMS sensor, maximum support of 30 million pixels. 2. DV with 2 LED fill lights, easy to fill light in weak light environment, take better clear and bright photos.3. 16X digital zoom, can be enlarged or reduced focal length according to the demand.4. It comes with a remote control, which can be used to control the camcorder to take photos and videos anywhere and anytime by your friends and family5. LCD screen size: 3.0 inch6. Resolution support: 2.7K7. Facial detection: support8. Storage medium: SD card (not included)9. Battery: 1500mAh NP-40 lithium battery10. Packing list: Host, lithium battery, manual, DV bag, high-definition cable, data cable, lens cover

Read more less

1. Aperture: F/NO: 2.2 f equals 4.88mm2. Zoom: 30x3. Sensor type: CMOS4. Resolution: 4K5. Weight: 380g6. Size: 128x70x68mm7. Sensor pixels: 13 million8. White balance: Auto/daytime/cloudy/tungsten light/fluorescent light9. Static effective pixels: 4 million10. Storage medium: Support SD card (expandable to 128GB, not included) 11. Battery type: Li-ion battery NP-12012. Battery life: 140 minutes13. Additional functions: Camera function, night shot function, support WIFI14. Hot shoe interface: External microphone, LED light15. Selfie: 2 seconds/5 seconds/10 seconds16. Color display: 3.1 inches IPS capacitive touch screen17. Video format: MP4 AVC/H.26418. Video resolution: UHD: 3824x2160 ("DAR" 24fps), QHD: 2560x1440 (30fps), FHD: 1920x1080 (60fps), HD: 1280x720 (120fps), VGA: 640x480 (30fps)19. Packing list: Charger + lithium battery + HD cable + remote control + camera bag + data cable + manual + lens cover + adapter (Take the specifications of the title and the actual product received to prevail)

Read more less

1. Aperture: F/NO: 2.2 f equals 4.88mm2. Zoom: 30x3. Sensor type: CMOS4. Resolution: 4K5. Weight: 380g6. Size: 128x70x68mm7. Sensor pixels: 13 million8. White balance: Auto/daytime/cloudy/tungsten light/fluorescent light9. Static effective pixels: 4 million10. Storage medium: Support SD card (expandable to 128GB, not included) 11. Battery type: Li-ion battery NP-12012. Battery life: 140 minutes13. Additional functions: Camera function, night shot function, support WIFI14. Hot shoe interface: External microphone, LED light15. Selfie: 2 seconds/5 seconds/10 seconds16. Color display: 3.1 inches IPS capacitive touch screen17. Video format: MP4 AVC/H.26418. Video resolution: UHD: 3824x2160 ("DAR" 24fps), QHD: 2560x1440 (30fps), FHD: 1920x1080 (60fps), HD: 1280x720 (120fps), VGA: 640x480 (30fps)19. Packing list: Charger + lithium battery + HD cable + remote control + camera bag + data cable + manual + lens cover + adapter (Take the specifications of the title and the actual product received to prevail)

Read more less

1. Lens: F is equal to 4.9-59mm. F.NO2.8-3.137mm2. Zoom: Video/Camera: 12X optical zoom 100X digital zoom3. Sensor type: CMOS4. Resolution: 4K5. Weight: 380g6. Size: 128x70x68mm7. Sensor pixels: 5 million8. White balance: Auto/daytime/cloudy/tungsten light/fluorescent light9. Static effective pixels: 4 million10. Storage medium: Support SD card (expandable to 128GB, not included) USB2.011. Battery type: Li-ion battery NP-12012. Battery life: 140 minutes13. Additional functions: Camera function, night shot function, support WIFI14. Hot shoe interface: External microphone, LED light15. Self timer: 2 seconds/5 seconds/10 seconds16. Color display: 3.1-inch IPS capacitive touch screen (16:9)17. Video format: MP4 AVC/H.26418. Photo format: JPEG19. Photo resolution: 24M/20M/16M/12M/10M/7M(HD)/5M/3M/2M(HD)/VGA20. Video resolution: UHD (4K): 2880x2160 (24fps), QHD (2K): 2560x1440 (30fps), FHD (1080P): 1920x1080 (60fps), HD (720P): 1280x720 (120fps), VGA: 640x480 ( 30fps)21. Packing list: Machine + charger + battery + data cable + HD cable + camera bag + manual + warranty card (Take the specifications of the title and the actual product received to prevail)

Read more less

1. Aperture: F/NO: 2.2 f equals 4.88mm2. Zoom: 30x3. Sensor type: CMOS4. Resolution: 4K5. Weight: 380g6. Size: 128x70x68mm7. Sensor pixels: 13 million8. White balance: Auto/daytime/cloudy/tungsten light/fluorescent light9. Static effective pixels: 4 million10. Storage medium: Support SD card (expandable to 128GB, not included) 11. Battery type: Li-ion battery NP-12012. Battery life: 140 minutes13. Additional functions: Camera function, night shot function, support WIFI14. Hot shoe interface: External microphone, LED light15. Selfie: 2 seconds/5 seconds/10 seconds16. Color display: 3.1 inches IPS capacitive touch screen17. Video format: MP4 AVC/H.26418. Video resolution: UHD: 3824x2160 ("DAR" 24fps), QHD: 2560x1440 (30fps), FHD: 1920x1080 (60fps), HD: 1280x720 (120fps), VGA: 640x480 (30fps)19. Packing list: Charger + lithium battery + HD cable + remote control + camera bag + data cable + manual + lens cover + adapter (Take the specifications of the title and the actual product received to prevail)

Read more less

1. Aperture: F/NO: 2.2 f equals 4.88mm2. Zoom: 30x3. Sensor type: CMOS4. Resolution: 4K5. Weight: 380g6. Size: 128x70x68mm7. Sensor pixels: 13 million8. White balance: Auto/daytime/cloudy/tungsten light/fluorescent light9. Static effective pixels: 4 million10. Storage medium: Support SD card (expandable to 128GB, not included) 11. Battery type: Li-ion battery NP-12012. Battery life: 140 minutes13. Additional functions: Camera function, night shot function, support WIFI14. Hot shoe interface: External microphone, LED light15. Selfie: 2 seconds/5 seconds/10 seconds16. Color display: 3.1 inches IPS capacitive touch screen17. Video format: MP4 AVC/H.26418. Video resolution: UHD: 3824x2160 ("DAR" 24fps), QHD: 2560x1440 (30fps), FHD: 1920x1080 (60fps), HD: 1280x720 (120fps), VGA: 640x480 (30fps)19. Packing list: Charger + lithium battery + HD cable + remote control + camera bag + data cable + manual + lens cover + adapter (Take the specifications of the title and the actual product received to prevail)

Read more less

1. Lens: F is equal to 4.9-59mm. F.NO2.8-3.137mm2. Zoom: Video/Camera: 12X optical zoom 100X digital zoom3. Sensor type: CMOS4. Resolution: 4K5. Weight: 380g6. Size: 128x70x68mm7. Sensor pixels: 5 million8. White balance: Auto/daytime/cloudy/tungsten light/fluorescent light9. Static effective pixels: 4 million10. Storage medium: Support SD card (expandable to 128GB, not included) USB2.011. Battery type: Li-ion battery NP-12012. Battery life: 140 minutes13. Additional functions: Camera function, night shot function, support WIFI14. Hot shoe interface: External microphone, LED light15. Self timer: 2 seconds/5 seconds/10 seconds16. Color display: 3.1-inch IPS capacitive touch screen (16:9)17. Video format: MP4 AVC/H.26418. Photo format: JPEG19. Photo resolution: 24M/20M/16M/12M/10M/7M(HD)/5M/3M/2M(HD)/VGA20. Video resolution: UHD (4K): 2880x2160 (24fps), QHD (2K): 2560x1440 (30fps), FHD (1080P): 1920x1080 (60fps), HD (720P): 1280x720 (120fps), VGA: 640x480 ( 30fps)21. Packing list: Machine + charger + battery + data cable + HD cable + camera bag + manual + warranty card (Take the specifications of the title and the actual product received to prevail)

Read more less

1. Lens: F is equal to 4.9-59mm. F.NO2.8-3.137mm2. Zoom: Video/Camera: 12X optical zoom 100X digital zoom3. Sensor type: CMOS4. Resolution: 4K5. Weight: 380g6. Size: 128x70x68mm7. Sensor pixels: 5 million8. White balance: Auto/daytime/cloudy/tungsten light/fluorescent light9. Static effective pixels: 4 million10. Storage medium: Support SD card (expandable to 128GB, not included) USB2.011. Battery type: Li-ion battery NP-12012. Battery life: 140 minutes13. Additional functions: Camera function, night shot function, support WIFI14. Hot shoe interface: External microphone, LED light15. Self timer: 2 seconds/5 seconds/10 seconds16. Color display: 3.1-inch IPS capacitive touch screen (16:9)17. Video format: MP4 AVC/H.26418. Photo format: JPEG19. Photo resolution: 24M/20M/16M/12M/10M/7M(HD)/5M/3M/2M(HD)/VGA20. Video resolution: UHD (4K): 2880x2160 (24fps), QHD (2K): 2560x1440 (30fps), FHD (1080P): 1920x1080 (60fps), HD (720P): 1280x720 (120fps), VGA: 640x480 ( 30fps)21. Packing list: Machine + charger + battery + data cable + HD cable + camera bag + manual + warranty card (Take the specifications of the title and the actual product received to prevail)

Read more less

1. Lens: F is equal to 4.9-59mm. F.NO2.8-3.137mm2. Zoom: Video/Camera: 12X optical zoom 100X digital zoom3. Sensor type: CMOS4. Resolution: 4K5. Weight: 380g6. Size: 128x70x68mm7. Sensor pixels: 5 million8. White balance: Auto/daytime/cloudy/tungsten light/fluorescent light9. Static effective pixels: 4 million10. Storage medium: Support SD card (expandable to 128GB, not included) USB2.011. Battery type: Li-ion battery NP-12012. Battery life: 140 minutes13. Additional functions: Camera function, night shot function, support WIFI14. Hot shoe interface: External microphone, LED light15. Self timer: 2 seconds/5 seconds/10 seconds16. Color display: 3.1-inch IPS capacitive touch screen (16:9)17. Video format: MP4 AVC/H.26418. Photo format: JPEG19. Photo resolution: 24M/20M/16M/12M/10M/7M(HD)/5M/3M/2M(HD)/VGA20. Video resolution: UHD (4K): 2880x2160 (24fps), QHD (2K): 2560x1440 (30fps), FHD (1080P): 1920x1080 (60fps), HD (720P): 1280x720 (120fps), VGA: 640x480 ( 30fps)21. Packing list: Machine + charger + battery + data cable + HD cable + camera bag + manual + warranty card (Take the specifications of the title and the actual product received to prevail)

Read more less

1. 8 million pixel camera. 2. With 2.0 inch high-definition eye-protection display. 3. 3264x2448P camera resolution. 4. 1920x1080P video resolution. 5. It is equipped with four kinds of filters: black and white, retro, neon and retro green, which adds dreamy mystery. 6. Built-in three-time mode of 2 seconds, 5 seconds, 10 seconds. 7. Added mobile phone transfer photo function, only for Android. 8. USB portable charging, built-in 1200mAh large-capacity battery, can take more than 400 consecutive photos under continuous power, continuous recording for 2-3 hours. 9. All parts of the small camera are made of environmentally friendly materials that are safe, non-toxic and non-polluting. 10. Product size: 7.5x4.5x2.5cm.

Read more less

1. 2.0 inch LCD screen 2. 5.0 mega pixel camera 3. Storage: TF card up to 32G (not included) 4. Battery life: 12 hours 5. Size: 9*5*6cm 6. Body material: ABS

Read more less

1. 5.0MP HD camera. 2. 1.77 inch LCD screen. 3. Support 1080P HD video recording. 4. 30 meters waterproof, suitable for skiing, swimming, diving and other sports scenes. 5. Built-in rechargeable lithium battery, 1.5 hours battery life. 6. Storage: TF card (not included) 7. Body material: ABS 8. Product size: 91x68x43mm

Read more less

1. 2.0 inch LCD screen 2. 5.0 mega pixel camera 3. Storage: TF card up to 32G (not included) 4. Battery life: 12 hours 5. Size: 9*5*6cm 6. Body material: ABS

Read more less

1. 5.0MP HD camera. 2. 1.77 inch LCD screen. 3. Support 1080P HD video recording. 4. 30 meters waterproof, suitable for skiing, swimming, diving and other sports scenes. 5. Built-in rechargeable lithium battery, 1.5 hours battery life. 6. Storage: TF card (not included) 7. Body material: ABS 8. Product size: 91x68x43mm

Read more less

1. 28mm auto-focus lens. 2. 5 meters waterproof. 3. Simple operation, and no battery required. 4. Main material: ABS. 5. Film needs to be prepared by self.

Read more less

1. Body material: ABS 2. Lens: F/8 28mm, auto-focus 3. Shutter: 1/100s 4. 5 meters Waterproof 5. Simple operation, no battery required 6. Suitable for 35mm film (not included) 7. Good-looking retro film camera, suitable for children 8. Size: 12.5x8.5x4.0cm 9. Weight: 250g

Read more less

1. Body material: ABS 2. Lens: F/8 28mm, auto-focus 3. Shutter: 1/100s 4. 5 meters Waterproof 5. Simple operation, no battery required 6. Suitable for 35mm film (not included) 7. Good-looking retro film camera, suitable for children 8. Size: 12.5x8.5x4.0cm 9. Weight: 250g

Read more less

1. Body material: ABS 2. Lens: F/8 28mm, auto-focus 3. Shutter: 1/100s 4. 5 meters Waterproof 5. Simple operation, no battery required 6. Suitable for 35mm film (not included) 7. Good-looking retro film camera, suitable for children 8. Size: 12.5x8.5x4.0cm 9. Weight: 250g

Read more less

1. Body material: ABS 2. Lens: F/8 28mm, auto-focus 3. Shutter: 1/100s 4. 5 meters Waterproof 5. Simple operation, no battery required 6. Suitable for 35mm film (not included) 7. Good-looking retro film camera, suitable for children 8. Size: 12.5x8.5x4.0cm 9. Weight: 250g

Read more less

1. Body material: ABS 2. Lens: F/8 28mm, auto-focus 3. Shutter: 1/100s 4. 5 meters Waterproof 5. Simple operation, no battery required 6. Suitable for 35mm film (not included) 7. Good-looking retro film camera, suitable for children 8. Size: 12.5x8.5x4.0cm 9. Weight: 250g

Read more less

1. Interpolation 16.0 megapixel (real 1.3 megapixel) CMOS Sensor lens. 2. 2.4 inch TFT LCD 320*240 pixel screen. 3. Video format: AVI, video resolution: 1280*720 / 720*480 / 640*480 / 320*240. 4. Photo format: JPEG, photo resolution: 12M (4000*3000) / 5M (2592*1944) / 3M (2048*1536) / 1M (1024*768) / VGA (640*480). 5. Support white balance. 6. Audio recorder (microphone), video recording up to 1280*720 pixel. 7. Auto power off function, powered by lithium battery pack or 4 x AA batteries (not included). 8. Focal length: 20cm above. 9. Built in 64MB flash memory. 10. Support 5 PIN mini USB port, 3.5mm audio port.

Read more less

1. Power supply: 3 AA batteries 2. The handshake positions on both sides are made of non-slip material, which increases friction when the child holds it 3. Highlight LED light to compensate for low brightness environment 4. TF card capacity supports 8G-32G 5. The body adopts soft rubber design, which is durable and resistant to drop. 6. Lanyard design, easy to use 7. Main control built-in DDR, faster transmission and strong stability 8. Size: 140x90mm

Read more less

1. Material: ABS + PC2. Weight: 96 g3. Size: Sensor size: 1 / 1.7 inch, LCD screen size: 2.0 inch, Product size: 89.5 x 33.1 x 68.4 mm4. Effective pixels: 8 million5. Storage medium: SD card (not include)6. Body memory: 512 MB7. Operation mode: Full manual operation8. Power supply mode: Lithium battery9. Packing list: Exquisite packaging x 1, host x 1, data cable x 1, instruction manual x 1, card reader x 1, lanyard x 110. Optical Zoom: 4x11. Max resolution: 1280 x 102412. Battery life: 3-4 hours13. Applicable gift occasions: Opening ceremony, employee benefits, anniversary celebration, award commemoration, trade fair, advertising promotion, festival, wedding, housewarming, public relations planning, birthday, business gift

Read more less

Features: 1. 1080P, 8 million pixels, clear photos 2. With TF card slot and USB interface 3. Can listen to music, tell stories, etc., support MP3 format 4. Button operation, simple and convenient 5. Helps children develop hobbies Product parameters: 1. Display: 2.4 inches 2. Function: Picture/Video/Audio/Game 3. Front camera: 1080P/ 8 megapixels 4. Rear lens: 1080P/ 8 million pixels 5. Games: 4 kinds of games 6. Battery: 600mAh 7. Video format: AVI 8. Charging time: 2.0-2.5 hours 9. Number of photos: 2300 10. Extended storage: 32GB TF card (not included) 11. Weight: 98g 12. Charging voltage: DC 5V/1A Warning: 1. Contains small parts, not suitable for children under three years old 2. Do not approach the fire source when playing 3. The guardian should look after the child while playing

Read more less

1. Material: ABS + PC2. Weight: 96 g3. Size: Sensor size: 1 / 1.7 inch, LCD screen size: 2.0 inch, Product size: 89.5 x 33.1 x 68.4 mm4. Effective pixels: 8 million5. Storage medium: SD card (not include)6. Body memory: 512 MB7. Operation mode: Full manual operation8. Power supply mode: Lithium battery9. Packing list: Exquisite packaging x 1, host x 1, data cable x 1, instruction manual x 1, card reader x 1, lanyard x 110. Optical Zoom: 4x11. Max resolution: 1280 x 102412. Battery life: 3-4 hours13. Applicable gift occasions: Opening ceremony, employee benefits, anniversary celebration, award commemoration, trade fair, advertising promotion, festival, wedding, housewarming, public relations planning, birthday, business gift

Read more less

Features: 1. 1080P, 8 million pixels, clear photos 2. With TF card slot and USB interface 3. Can listen to music, tell stories, etc., support MP3 format 4. Button operation, simple and convenient 5. Helps children develop hobbies Product parameters: 1. Display: 2.4 inches 2. Function: Picture/Video/Audio/Game 3. Front camera: 1080P/ 8 megapixels 4. Rear lens: 1080P/ 8 million pixels 5. Games: 4 kinds of games 6. Battery: 600mAh 7. Video format: AVI 8. Charging time: 2.0-2.5 hours 9. Number of photos: 2300 10. Extended storage: 32GB TF card (not included) 11. Weight: 98g 12. Charging voltage: DC 5V/1A Warning: 1. Contains small parts, not suitable for children under three years old 2. Do not approach the fire source when playing 3. The guardian should look after the child while playing

Read more less

1. Weight: 94 g2. Material: Plastic3. Dimensions: 78 x 45 x 20 cm4. Battery capacity: 750 mah5. Lens type: wide-angle lens6. Power supply method: USB power supply7. Effective pixels: 24 million and above8. Ability development: observation ability, thinking ability, logical ability, exploration ability, aesthetic ability, expression ability, hand-eye ability, imagination ability9. Packing list: camera x1, data cable x1, card reader x1, lanyard x1, sticker x1, protective cover x110. Maximum resolution: 5120 x 3840

Read more less

1. Weight: 94 g2. Material: Plastic3. Dimensions: 78 x 45 x 20 cm4. Battery capacity: 750 mah5. Lens type: wide-angle lens6. Power supply method: USB power supply7. Effective pixels: 24 million and above8. Ability development: observation ability, thinking ability, logical ability, exploration ability, aesthetic ability, expression ability, hand-eye ability, imagination ability9. Packing list: camera x1, data cable x1, card reader x1, lanyard x1, sticker x1, protective cover x110. Maximum resolution: 5120 x 3840

Read more less