Consumer Electronics

1. Zinc alloy XLR head, and the plug is nickel-plated2. Its conductor is bare copper wire, PVC sheath Nickel-plated plug3. Product use: suitable for mixers, power amplifiers, active speakers, microphones and other equipment.4. 4. This adapter converts the audio output of the XLR end into dual RCA outputs, and can also convert the XLR input interface into 2 RCA inputs. However, 2 RCAs cannot input 2 audio signals at the same time, and can only be used by a single interface. It is not possible to combine dual RCA audio signals into XLR audio signals, please pay attention to the usage method.5. Length: about 20cm (including plug)

Read more less

1. Material: flame retardant plastic, electronic components2. Heating method: PTC ceramic heater3. Safety protection: overheating power off, flame retardant material, dumping power off, anti-scalding grille4. Applicable area: 21-30 square meters5. Speed adjustment gear: third gear6. Timing: 4-12 hours7. Rated voltage: 220-240V8. Rated frequency: 50Hz9. Power: 8W/1400W/2000W10. Switch Type: Touch11. Air supply method: shaking his head12. Noise: 37-45dB13. Remote control battery: CR2025 button battery x 2 (delivery with battery)14. Low noise operation, more comfortable to use15. The base is designed with a remote control card slot, which is convenient for storing the remote control16. Product size: 41 x 18.6 x 12.6 cm17. Product net weight: 1.8 kg

Read more less

1. Material: flame retardant plastic, electronic components2. Heating method: PTC ceramic heater3. Safety protection: overheating power off, flame retardant material, dumping power off, anti-scalding grille4. Applicable area: 15-50 square meters5. Speed adjustment gear: third gear6. Remote control timing: 4-12 hours7. Rated voltage: 220-240V8. Rated frequency: 50Hz9. Power: 5W/750W/1500W10. Switch Type: Mechanical/Touch11. Air supply method: shaking his head12. Touch screen remote control battery: CR2025 button battery x 2 (delivery with battery)13. Real-time temperature display, touch key design, more convenient to use14. Low noise operation, more comfortable to use15. Natural and comfortable, as warm as the sun16. No light and heat do not hurt the eyes, do not disturb the sleep of the family17. Product size: 40.7 x 18.6 x 12.6 cm

Read more less

1. Material: flame retardant plastic, electronic components2. Heating method: PTC ceramic heater3. Safety protection: overheating power off, flame retardant material, dumping power off, anti-scalding grille4. Applicable area: 21-30 square meters5. Speed adjustment gear: third gear6. Timing: 4-12 hours7. Rated voltage: 220-240V8. Rated frequency: 50Hz9. Power: 8W/1400W/2000W10. Switch Type: Touch11. Air supply method: shaking his head12. Noise: 37-45dB13. Remote control battery: CR2025 button battery x 2 (delivery with battery)14. Low noise operation, more comfortable to use15. The base is designed with a remote control card slot, which is convenient for storing the remote control16. Product size: 41 x 18.6 x 12.6 cm17. Product net weight: 1.8 kg

Read more less

1. Material: flame retardant ABS, electronic components2. Heating method: PTC ceramic heater3. Features: internal temperature control protection, flame retardant body, no light heating, multiple protection, large-angle air supply4. Safety protection: overheating power off, flame retardant material, dumping power off, overload protection, short circuit protection, anti-scalding grille5. Applicable area: about 20 square meters6. Rated voltage: 220-240V7. Rated frequency: 50Hz8. Rated power: 500W9. Operation mode: mechanical10. Air supply method: shaking his head11. Low noise operation, more comfortable to use12. Natural and comfortable, as warm as the sun13. No light and heat do not hurt the eyes, do not disturb the sleep of the family14. Product size: 26.2 x 10.3 x 11 cm

Read more less

1. Adopt metal plug, sturdy and durable2. Bold 7mm wire, 22AWG oxygen-free copper conductor, double-layer shielding, and obvious noise reduction.3. The outer nylon mesh protective layer can be used indoors and outdoors, with tensile and compressive resistance.4. Standard 6.35mm (1/4 interface) sophomore core, which is widely used and good at compatibility.5. Product use: used for the connection between electric guitars, electronic organs, basses, etc., speakers and power amplifiers.

Read more less

1. Adopt integrated wire bifurcation, strong and durable, good contact performance,2. Metal plating shell, effectively shield external interference3. Double-layer shielding, 22AWG thick wire, high-fidelity transmission, effective noise reduction4. The contact points are silver-plated to ensure high-quality contact performance and better anti-oxidation effect.5. Product use: It can divide XLR 3pin interfaces such as amplifiers, microphones, mixers, etc. into two parts.

Read more less

1. Adopt metal plug, sturdy and durable2. Bold 7mm wire, 22AWG oxygen-free copper conductor, double-layer shielding, and obvious noise reduction.3. The outer nylon mesh protective layer can be used indoors and outdoors, with tensile and compressive resistance.4. Standard 6.35mm (1/4 interface) sophomore core, which is widely used and good at compatibility.5. Product use: used for the connection between electric guitars, electronic organs, basses, etc., speakers and power amplifiers.

Read more less

1. Adopt metal plug, sturdy and durable2. Bold 7mm wire, 22AWG oxygen-free copper conductor, double-layer shielding, and obvious noise reduction.3. The outer nylon mesh protective layer can be used indoors and outdoors, with tensile and compressive resistance.4. Standard 6.35mm (1/4 interface) sophomore core, which is widely used and good at compatibility.5. Product use: used for the connection between electric guitars, electronic organs, basses, etc., speakers and power amplifiers.

Read more less

1. Adopt metal plug, sturdy and durable2. Bold 7mm wire, 22AWG oxygen-free copper conductor, double-layer shielding, and obvious noise reduction.3. The outer nylon mesh protective layer can be used indoors and outdoors, with tensile and compressive resistance.4. Standard 6.35mm (1/4 interface) sophomore core, which is widely used and good at compatibility.5. Product use: used for the connection between electric guitars, electronic organs, basses, etc., speakers and power amplifiers.

Read more less

1. Mini digital sound level meter with stable and reliable performance.2. Wide measurement range from 30dB to 130dBA.3. Data hold function, maximum and minimum value measurement.4. LCD display with backlight, convenient to use at night.5. Low battery indication, automatic & manual power off function.6. Compact and light, convenient to hold and carry.7. Equipped with sponge ball for sensor protection.6. Power supply: 3 x 1.5V AAA battery (Not included)

Read more less

1. Use these accessories to turn your hair dryer into a curling iron, or from a curling iron to a hair dryer2. The hair is automatically coiled, strong airflow, fast drying3. Material: ABS4. Dimensions: long barrel 19 x 4 x 3cm, hair dryer adapter 7 x 6.5 x 3.5cm, curling iron adapter 9.5 x 6 x 4cm5. Weight: long barrel 100g/pair, hair dryer adapter 44g, curling iron adapter 100g6. Note: the product is only accessories, does not include hair dryer

Read more less

1. One EMF Tester with two uses, testing the electric field and the magnetic field radiation at the same time.2. Measure radiation of high voltage power lines, appliances, electrical wires.3. Sound-light alarm, when the test result exceeds the safe value, the instrument will alarm automatically.4. Data hold and max measurement, one-key lock the radiation value.5. Large & clear LCD display of the values for easy reading.6. Easy to operate with easy one-hand operation, easy to carry and make field measurement.7. Can measure the environment temperature with 2 temperature units (C/F).8. Electric field strength range: 0~1999V/m9. Electric field strength resolution: 1V/m10. Magnetic field strength frequency range: 20Hz~300Hz11. Electric field strength frequency range: 20Hz~3500MHz12. Power Supply: 3 x 1.5V AAA battery (Not included)

Read more less

1. Use these accessories to turn your hair dryer into a curling iron, or from a curling iron to a hair dryer2. The hair is automatically coiled, strong airflow, fast drying3. Material: ABS4. Dimensions: long barrel 19 x 4 x 3cm, hair dryer adapter 7 x 6.5 x 3.5cm, curling iron adapter 9.5 x 6 x 4cm5. Weight: long barrel 100g/pair, hair dryer adapter 44g, curling iron adapter 100g6. Note: the product is only accessories, does not include hair dryer

Read more less

1. A curling iron, create curls in both directions, the upgraded version of the curling iron can wrap the hair in both clockwise and counterclockwise directions, no need to replace the curling iron, and create fluffy curls faster2. Let the blow dryer curl your hair. Low temperature does not hurt the hair automatically curls, easy to style3. Made of high quality material, durable4. Material: Nylon5. Dimensions: 4 x 18.6 cm, 3 x 18.6 cm6. 3cm 65.8g, 4cm 96.7g

Read more less

1. Mini digital sound level meter with stable and reliable performance.2. Wide measurement range from 30dB to 130dBA.3. Data hold function, maximum and minimum value measurement.4. LCD display with backlight, convenient to use at night.5. Low battery indication, automatic & manual power off function.6. Compact and light, convenient to hold and carry.7. Equipped with sponge ball for sensor protection.6. Power supply: 3 x 1.5V AAA battery (Not included)

Read more less

1. Mini lux meter with stable, safe and reliable measurement.2. Wide measurement range 0-200,000 lux and automatic/manual range shift.3. Measuring unit is switchable: Lux or FC.4. MAX / MIN / Data hold functions, high accuracy.5. LCD display with backlight for easy operation in darkness.6. Low battery indication & Auto power off, energy saving.7. Power supply: 3 x 1.5V AAA batteries (Not Included)

Read more less

1. Handheld design and non-slip pen type handle for easy operation.2. Built-in automatic temperature compensation(ATC) to get precise results.3. Measuring Rang: 0.00ppt-9.99ppt 10.0ppt-50ppt, very easy to test.4. With temperature units in C / F(switchable) and switchable backlight for convenient use in dark.5. With a replaceable sensor probe, the electrode probe can be replaced with an insert type design for convenient and fast replacement.6. Suitable for water source monitoring, aquaculture, environmental protection, printing and dyeing, electroplating, beverage industry and scientific research unit to determine the water quality salinity.7. Power supply: LR44 battery x 4pcs(not included).

Read more less

1. Rated voltage: 220V~2. Rated frequency: 50Hz3. Rated power: 450-800W4. Honeycomb mesh air outlet, double convective air volume, stronger warm air5. Low energy consumption heating device, save power6. Quiet system design, low noise operation7. Double protection, overheating and power-off design when dumping, not afraid of accidental touch8. Intelligent constant temperature PTC ceramic heating element9. Dimensions: 140x140x100mm

Read more less

1. Support network printing2. Paper capacity: 573. Improve print clarity4. Printing medium: thermal paper5. Graffiti DIY, document printing6. Battery capacity: 1200mAh7. Photo printing, English dictionary8. Question bank encyclopedia, to-do list9. Bluetooth connection, website printing10. Chinese character printing, voice note11. Charging interface: 5V-MicroUSB12. Photo search and print, massive dynamic question bank13. OCR optical recognition, multilingual recognition, editable copy14. Adopt new printing technology to reduce the cost of consumables by 60%15. Support system: APP intervention (mobile phone android platform, Apple iOS platform)16. Dimensions: 82x82x45mm17. Net weight: 175g

Read more less

1. Rated voltage: 220V~2. Rated frequency: 50Hz3. Rated power: 450-800W4. Honeycomb mesh air outlet, double convective air volume, stronger warm air5. Low energy consumption heating device, save power6. Quiet system design, low noise operation7. Double protection, overheating and power-off design when dumping, not afraid of accidental touch8. Intelligent constant temperature PTC ceramic heating element9. Dimensions: 140x140x100mm

Read more less

1. Rated voltage: 220V~2. Rated frequency: 50Hz3. Rated power: 450-800W4. Honeycomb mesh air outlet, double convective air volume, stronger warm air5. Low energy consumption heating device, save power6. Quiet system design, low noise operation7. Double protection, overheating and power-off design when dumping, not afraid of accidental touch8. Intelligent constant temperature PTC ceramic heating element9. Dimensions: 140x140x100mm

Read more less

1. Rated voltage: 220V~2. Rated frequency: 50Hz3. Rated power: 450-800W4. Honeycomb mesh air outlet, double convective air volume, stronger warm air5. Low energy consumption heating device, save power6. Quiet system design, low noise operation7. Double protection, overheating and power-off design when dumping, not afraid of accidental touch8. Intelligent constant temperature PTC ceramic heating element9. Dimensions: 140x140x100mm

Read more less

1. Support network printing2. Paper capacity: 573. Improve print clarity4. Printing medium: thermal paper5. Graffiti DIY, document printing6. Battery capacity: 1200mAh7. Photo printing, English dictionary8. Question bank encyclopedia, to-do list9. Bluetooth connection, website printing10. Chinese character printing, voice note11. Charging interface: 5V-MicroUSB12. Photo search and print, massive dynamic question bank13. OCR optical recognition, multilingual recognition, editable copy14. Adopt new printing technology to reduce the cost of consumables by 60%15. Support system: APP intervention (mobile phone android platform, Apple iOS platform)16. Dimensions: 82x82x45mm17. Net weight: 175g

Read more less

1. Silicone material, soft and skin-friendly2. Dustproof and waterproof, easy to clean, resistant to pulling3. Seamless fit, not easy to fall off4. Good texture, wear-resistant and durable5. Material: silicone6. Applicable models: for Meta Quest 27. Weight: about 4g

Read more less

1. Rated voltage: 220V~2. Rated frequency: 50Hz3. Rated power: 450-800W4. Honeycomb mesh air outlet, double convective air volume, stronger warm air5. Low energy consumption heating device, save power6. Quiet system design, low noise operation7. Double protection, overheating and power-off design when dumping, not afraid of accidental touch8. Intelligent constant temperature PTC ceramic heating element9. Dimensions: 140x140x100mm

Read more less

1. Test the pH level and temperature of solution/water with data hold function.2. Pocket size, lightweight and portable with switchable backlight & large LCD display for clear reading.3. Replaceable pH sensor probe - The electrode probe can be replaced with insert type design for convenient and fast replacement.4. ATC function (automatic temperature compensation), automatic calibration and IP65 fully waterproof design.5. Apply in water sources, soil-free growing, aquariums, hydroponics, laboratory, spas, swimming pools and other water systems.6. Power: 2 x AAABattery (Not Included)

Read more less

1. Rated voltage: 220V~2. Rated frequency: 50Hz3. Rated power: 450-800W4. Honeycomb mesh air outlet, double convective air volume, stronger warm air5. Low energy consumption heating device, save power6. Quiet system design, low noise operation7. Double protection, overheating and power-off design when dumping, not afraid of accidental touch8. Intelligent constant temperature PTC ceramic heating element9. Dimensions: 140x140x100mm

Read more less

1. Ergonomic design, one-hand comfortable grip & anti-slip & anti-fatigue.2. More accurate measurement & more sensitive response & more comprehensive functions.3. Intuitive LCD display with backlight, easy to read values of dissolved oxygen and temperature even in dark or strong light environment.4. Automatic temperature compensation (ATC), fast response and automatic calibration.5. It supports recording 99 groups of data manually, convenient to record / compare / view data with one key.6. Widely applicable to aquaculture, biological reaction, environmental detection, wastewater treatment, laboratory field, medical field, etc.7. Power supply: 4 x AAA battery (Not included)

Read more less

Features1. UHF wireless in-ear monitoring system. 2. A built-in limiter circuit for stage performances and a wide range of sounds eliminates distortion at excessive input levels. 3. Metal panel and body shell, makes it sturdy and durable 4. Provides desktop-level monitoring in an in-ear monitoring and receiving system with a wireless range from 80 to 100m, and a frequency range of 550-580MHz. 5. The signal-to-noise ratio of the dynamic range is improved, so that the system has excellent anti-interference ability, and once again shows the good original soundTransmitter Specifications1. Case specification:Standard 1U Case 2. Material: Metal panel and body housing case 3. Frequency range: UHF550-580MHz 4. Frequency interval: 25MHz 5. Transmit output power:100mW(50 ohms) 6. Audio input: XLR & 6.3mm duplex outlet 7. Earphone output: 6.3mm jack, volume adjustable 8. Headphone load impedance: Greater than or equal to 16 ohms 9. Voltage current consumption: DC 12V 250mA 10. Antenna interface: TNC jack (50 ohms) 11. Size: 48 x 10.5 x 4.3cmReceiver Specifications1. Oscillation mode: PLL synthesized Frequency 2. Width Frequency range: UHF550-580MHz (Corresponding transmitter frequency) 3. Frequency interval: 25MHz 4. Operate mode: Manual adjust 5. Receiving mode: Single tuning. 6. Comprehensive Frequency Response: 80Hz~15KHz+/-3dB 7. Output power (30 ohms): 2 x 35mW 8. Headphone load impedance: Greater than or equal to 16 ohms 9. Earphone output: 3.5mm jack 10. Power supply: 2 x AA batteries (not included) 11. Size: 8.5 x 6cm

Read more less

Features1. UHF wireless in-ear monitoring system. 2. A built-in limiter circuit for stage performances and a wide range of sounds eliminates distortion at excessive input levels. 3. Metal panel and body shell, makes it sturdy and durable 4. Provides desktop-level monitoring in an in-ear monitoring and receiving system with a wireless range from 80 to 100m, and a frequency range of 550-580MHz. 5. The signal-to-noise ratio of the dynamic range is improved, so that the system has excellent anti-interference ability, and once again shows the good original soundTransmitter Specifications1. Case specification:Standard 1U Case 2. Material: Metal panel and body housing case 3. Frequency range: UHF550-580MHz 4. Frequency interval: 25MHz 5. Transmit output power:100mW(50 ohms) 6. Audio input: XLR & 6.3mm duplex outlet 7. Earphone output: 6.3mm jack, volume adjustable 8. Headphone load impedance: Greater than or equal to 16 ohms 9. Voltage current consumption: DC 12V 250mA 10. Antenna interface: TNC jack (50 ohms) 11. Size: 48 x 10.5 x 4.3cmReceiver Specifications1. Oscillation mode: PLL synthesized Frequency 2. Width Frequency range: UHF550-580MHz (Corresponding transmitter frequency) 3. Frequency interval: 25MHz 4. Operate mode: Manual adjust 5. Receiving mode: Single tuning. 6. Comprehensive Frequency Response: 80Hz~15KHz+/-3dB 7. Output power (30 ohms): 2 x 35mW 8. Headphone load impedance: Greater than or equal to 16 ohms 9. Earphone output: 3.5mm jack 10. Power supply: 2 x AA batteries (not included) 11. Size: 8.5 x 6cm

Read more less

Features1. UHF wireless in-ear monitoring system. 2. A built-in limiter circuit for stage performances and a wide range of sounds eliminates distortion at excessive input levels. 3. Metal panel and body shell, make it sturdy and durable 4. Provides desktop-level monitoring in an in-ear monitoring and receiving system with a wireless range from 80 to 100m, and a frequency range of 550-580MHz. 5. The signal-to-noise ratio of the dynamic range is improved, so that the system has excellent anti-interference ability, and once again shows the good original soundTransmitter Specifications1. Case specification:Standard 1U Case 2. Material: Metal panel and body housing case 3. Frequency range: UHF550-580MHz 4. Frequency interval: 25MHz 5. Transmit output power:100mW(50 ohms) 6. Audio input: XLR & 6.3mm duplex outlet 7. Earphone output: 6.3mm jack, volume adjustable 8. Headphone load impedance: Greater than or equal to 16 ohms 9. Voltage current consumption: DC 12V 250mA 10. Antenna interface: TNC jack (50 ohms) 11. Size: 48 x 10.5 x 4.3cmReceiver Specifications1. Oscillation mode: PLL synthesized Frequency 2. Width Frequency range: UHF500-830MHz (Corresponding transmitter frequency) 3. Frequency interval: 25MHz 4. Operate mode: Manual adjust 5. Receiving mode: Single tuning. 6. Comprehensive Frequency Reaponse: 80Hz~15KHz+/-3dB 7. Output power (30 ohms): 2 x 35mW 8. Headphone load impedance: Greater than or equal to 16 ohms 9. Earphone output: 3.5mm jack 10. Power supply: 2 x AA batteries (not included) 11. Size: 8.5 x 6cm

Read more less

1. Silicone material, soft and skin-friendly2. Dustproof and waterproof, easy to clean, resistant to pulling3. Seamless fit, not easy to fall off4. Good texture, wear-resistant and durable5. Material: silicone6. Applicable models: for Meta Quest 27. Weight: about 4g

Read more less

1. Silicone material, soft and skin-friendly2. Dustproof and waterproof, easy to clean, resistant to pulling3. Seamless fit, not easy to fall off4. Good texture, wear-resistant and durable5. Material: silicone6. Applicable models: for Meta Quest 27. Weight: about 4g

Read more less

Features1. UHF wireless in-ear monitoring system. 2. A built-in limiter circuit for stage performances and a wide range of sounds eliminates distortion at excessive input levels. 3. Metal panel and body shell, makes it sturdy and durable 4. Provides desktop-level monitoring in an in-ear monitoring and receiving system with a wireless range from 80 to 100m, and a frequency range of 550-580MHz. 5. The signal-to-noise ratio of the dynamic range is improved, so that the system has excellent anti-interference ability, and once again shows the good original soundTransmitter Specifications1. Case specification:Standard 1U Case 2. Material: Metal panel and body housing case 3. Frequency range: UHF550-580MHz 4. Frequency interval: 25MHz 5. Transmit output power:100mW(50 ohms) 6. Audio input: XLR & 6.3mm duplex outlet 7. Earphone output: 6.3mm jack, volume adjustable 8. Headphone load impedance: Greater than or equal to 16 ohms 9. Voltage current consumption: DC 12V 250mA 10. Antenna interface: TNC jack (50 ohms) 11. Size: 48 x 10.5 x 4.3cmReceiver Specifications1. Oscillation mode: PLL synthesized Frequency 2. Width Frequency range: UHF550-580MHz (Corresponding transmitter frequency) 3. Frequency interval: 25MHz 4. Operate mode: Manual adjust 5. Receiving mode: Single tuning. 6. Comprehensive Frequency Response: 80Hz~15KHz+/-3dB 7. Output power (30 ohms): 2 x 35mW 8. Headphone load impedance: Greater than or equal to 16 ohms 9. Earphone output: 3.5mm jack 10. Power supply: 2 x AA batteries (not included) 11. Size: 8.5 x 6cm

Read more less

Features1. UHF wireless in-ear monitoring system. 2. A built-in limiter circuit for stage performances and a wide range of sounds eliminates distortion at excessive input levels. 3. Metal panel and body shell, makes it sturdy and durable 4. Provides desktop-level monitoring in an in-ear monitoring and receiving system with a wireless range from 80 to 100m, and a frequency range of 550-580MHz. 5. The signal-to-noise ratio of the dynamic range is improved, so that the system has excellent anti-interference ability, and once again shows the good original soundTransmitter Specifications1. Case specification:Standard 1U Case 2. Material: Metal panel and body housing case 3. Frequency range: UHF550-580MHz 4. Frequency interval: 25MHz 5. Transmit output power:100mW(50 ohms) 6. Audio input: XLR & 6.3mm duplex outlet 7. Earphone output: 6.3mm jack, volume adjustable 8. Headphone load impedance: Greater than or equal to 16 ohms 9. Voltage current consumption: DC 12V 250mA 10. Antenna interface: TNC jack (50 ohms) 11. Size: 48 x 10.5 x 4.3cmReceiver Specifications1. Oscillation mode: PLL synthesized Frequency 2. Width Frequency range: UHF550-580MHz (Corresponding transmitter frequency) 3. Frequency interval: 25MHz 4. Operate mode: Manual adjust 5. Receiving mode: Single tuning. 6. Comprehensive Frequency Reaponse: 80Hz~15KHz+/-3dB 7. Output power (30 ohms): 2 x 35mW 8. Headphone load impedance: Greater than or equal to 16 ohms 9. Earphone output: 3.5mm jack 10. Power supply: 2 x AA batteries (not included) 11. Size: 8.5 x 6cm

Read more less

1. Silicone material, soft and skin-friendly2. Dustproof and waterproof, easy to clean, resistant to pulling3. Seamless fit, not easy to fall off4. Good texture, wear-resistant and durable5. Material: silicone6. Applicable models: for Meta Quest 27. Weight: about 4g

Read more less

1. Silicone material, soft and skin-friendly2. Dustproof and waterproof, easy to clean, resistant to pulling3. Seamless fit, not easy to fall off4. Good texture, wear-resistant and durable5. Material: silicone6. Applicable models: for Meta Quest 27. Weight: about 4g

Read more less

Features1. UHF wireless in-ear monitoring system. 2. A built-in limiter circuit for stage performances and a wide range of sounds eliminates distortion at excessive input levels. 3. Metal panel and body shell, makes it sturdy and durable 4. Provides desktop-level monitoring in an in-ear monitoring and receiving system with a wireless range from 80 to 100m, and a frequency range of 550-580MHz. 5. The signal-to-noise ratio of the dynamic range is improved, so that the system has excellent anti-interference ability, and once again shows the good original soundTransmitter Specifications1. Case specification:Standard 1U Case 2. Material: Metal panel and body housing case 3. Frequency range: UHF550-580MHz 4. Frequency interval: 25MHz 5. Transmit output power:100mW(50 ohms) 6. Audio input: XLR & 6.3mm duplex outlet 7. Earphone output: 6.3mm jack, volume adjustable 8. Headphone load impedance: Greater than or equal to 16 ohms 9. Voltage current consumption: DC 12V 250mA 10. Antenna interface: TNC jack (50 ohms) 11. Size: 48 x 10.5 x 4.3cmReceiver Specifications1. Oscillation mode: PLL synthesized Frequency 2. Width Frequency range: UHF550-580MHz (Corresponding transmitter frequency) 3. Frequency interval: 25MHz 4. Operate mode: Manual adjust 5. Receiving mode: Single tuning. 6. Comprehensive Frequency Response: 80Hz~15KHz+/-3dB 7. Output power (30 ohms): 2 x 35mW 8. Headphone load impedance: Greater than or equal to 16 ohms 9. Earphone output: 3.5mm jack 10. Power supply: 2 x AA batteries (not included) 11. Size: 8.5 x 6cm

Read more less

1. Silicone material, soft and skin-friendly2. Dustproof and waterproof, easy to clean, resistant to pulling3. Seamless fit, not easy to fall off4. Good texture, wear-resistant and durable5. Material: silicone6. Applicable models: for Meta Quest 27. Weight: about 4g

Read more less

Features1. UHF wireless in-ear monitoring system. 2. A built-in limiter circuit for stage performances and a wide range of sounds eliminates distortion at excessive input levels. 3. Metal panel and body shell, makes it sturdy and durable 4. Provides desktop-level monitoring in an in-ear monitoring and receiving system with a wireless range from 80 to 100m, and a frequency range of 550-580MHz. 5. The signal-to-noise ratio of the dynamic range is improved, so that the system has excellent anti-interference ability, and once again shows the good original soundTransmitter Specifications1. Case specification:Standard 1U Case 2. Material: Metal panel and body housing case 3. Frequency range: UHF550-580MHz 4. Frequency interval: 25MHz 5. Transmit output power:100mW(50 ohms) 6. Audio input: XLR & 6.3mm duplex outlet 7. Earphone output: 6.3mm jack, volume adjustable 8. Headphone load impedance: Greater than or equal to 16 ohms 9. Voltage current consumption: DC 12V 250mA 10. Antenna interface: TNC jack (50 ohms) 11. Size: 48 x 10.5 x 4.3cmReceiver Specifications1. Oscillation mode: PLL synthesized Frequency 2. Width Frequency range: UHF550-580MHz (Corresponding transmitter frequency) 3. Frequency interval: 25MHz 4. Operate mode: Manual adjust 5. Receiving mode: Single tuning. 6. Comprehensive Frequency Response: 80Hz~15KHz+/-3dB 7. Output power (30 ohms): 2 x 35mW 8. Headphone load impedance: Greater than or equal to 16 ohms 9. Earphone output: 3.5mm jack 10. Power supply: 2 x AA batteries (not included) 11. Size: 8.5 x 6cm

Read more less

Features1. UHF wireless in-ear monitoring system. 2. A built-in limiter circuit for stage performances and a wide range of sounds eliminates distortion at excessive input levels. 3. Metal panel and body shell, makes it sturdy and durable 4. Provides desktop-level monitoring in an in-ear monitoring and receiving system with a wireless range from 80 to 100m, and a frequency range of 550-580MHz. 5. The signal-to-noise ratio of the dynamic range is improved, so that the system has excellent anti-interference ability, and once again shows the good original soundTransmitter Specifications1. Case specification:Standard 1U Case 2. Material: Metal panel and body housing case 3. Frequency range: UHF550-580MHz 4. Frequency interval: 25MHz 5. Transmit output power:100mW(50 ohms) 6. Audio input: XLR & 6.3mm duplex outlet 7. Earphone output: 6.3mm jack, volume adjustable 8. Headphone load impedance: Greater than or equal to 16 ohms 9. Voltage current consumption: DC 12V 250mA 10. Antenna interface: TNC jack (50 ohms) 11. Size: 48 x 10.5 x 4.3cmReceiver Specifications1. Oscillation mode: PLL synthesized Frequency 2. Width Frequency range: UHF550-580MHz (Corresponding transmitter frequency) 3. Frequency interval: 25MHz 4. Operate mode: Manual adjust 5. Receiving mode: Single tuning. 6. Comprehensive Frequency Response: 80Hz~15KHz+/-3dB 7. Output power (30 ohms): 2 x 35mW 8. Headphone load impedance: Greater than or equal to 16 ohms 9. Earphone output: 3.5mm jack 10. Power supply: 2 x AA batteries (not included) 11. Size: 8.5 x 6cm

Read more less

1. Material: plastic/hypa2. Use environment: home3. Applicable area: 101-150 square meters4. For Xiaomi Mijia STFCR01SZ Vacuum Cleaner5. High compatibility with the real machine6. Filter dust to purify the air7. Weight: side brush 57g/pair, filter 61g/piece, rag 18g/piece, set 136g/set

Read more less

Features1. UHF wireless in-ear monitoring system. 2. A built-in limiter circuit for stage performances and a wide range of sounds eliminates distortion at excessive input levels. 3. Metal panel and body shell, makes it sturdy and durable 4. Provides desktop-level monitoring in an in-ear monitoring and receiving system with a wireless range from 80 to 100m, and a frequency range of 550-580MHz. 5. The signal-to-noise ratio of the dynamic range is improved, so that the system has excellent anti-interference ability, and once again shows the good original soundTransmitter Specifications1. Case specification:Standard 1U Case 2. Material: Metal panel and body housing case 3. Frequency range: UHF550-580MHz 4. Frequency interval: 25MHz 5. Transmit output power:100mW(50 ohms) 6. Audio input: XLR & 6.3mm duplex outlet 7. Earphone output: 6.3mm jack, volume adjustable 8. Headphone load impedance: Greater than or equal to 16 ohms 9. Voltage current consumption: DC 12V 250mA 10. Antenna interface: TNC jack (50 ohms) 11. Size: 48 x 10.5 x 4.3cmReceiver Specifications1. Oscillation mode: PLL synthesized Frequency 2. Width Frequency range: UHF550-580MHz (Corresponding transmitter frequency) 3. Frequency interval: 25MHz 4. Operate mode: Manual adjust 5. Receiving mode: Single tuning. 6. Comprehensive Frequency Reaponse: 80Hz~15KHz+/-3dB 7. Output power (30 ohms): 2 x 35mW 8. Headphone load impedance: Greater than or equal to 16 ohms 9. Earphone output: 3.5mm jack 10. Power supply: 2 x AA batteries (not included) 11. Size: 8.5 x 6cm

Read more less

Features1. UHF wireless in-ear monitoring system. 2. A built-in limiter circuit for stage performances and a wide range of sounds eliminates distortion at excessive input levels. 3. Metal panel and body shell, makes it sturdy and durable 4. Provides desktop-level monitoring in an in-ear monitoring and receiving system with a wireless range from 80 to 100m, and a frequency range of 550-580MHz. 5. The signal-to-noise ratio of the dynamic range is improved, so that the system has excellent anti-interference ability, and once again shows the good original soundTransmitter Specifications1. Case specification:Standard 1U Case 2. Material: Metal panel and body housing case 3. Frequency range: UHF550-580MHz 4. Frequency interval: 25MHz 5. Transmit output power:100mW(50 ohms) 6. Audio input: XLR & 6.3mm duplex outlet 7. Earphone output: 6.3mm jack, volume adjustable 8. Headphone load impedance: Greater than or equal to 16 ohms 9. Voltage current consumption: DC 12V 250mA 10. Antenna interface: TNC jack (50 ohms) 11. Size: 48 x 10.5 x 4.3cmReceiver Specifications1. Oscillation mode: PLL synthesized Frequency 2. Width Frequency range: UHF550-580MHz (Corresponding transmitter frequency) 3. Frequency interval: 25MHz 4. Operate mode: Manual adjust 5. Receiving mode: Single tuning. 6. Comprehensive Frequency Response: 80Hz~15KHz+/-3dB 7. Output power (30 ohms): 2 x 35mW 8. Headphone load impedance: Greater than or equal to 16 ohms 9. Earphone output: 3.5mm jack 10. Power supply: 2 x AA batteries (not included) 11. Size: 8.5 x 6cm

Read more less

Features1. UHF wireless in-ear monitoring system. 2. A built-in limiter circuit for stage performances and a wide range of sounds eliminates distortion at excessive input levels. 3. Metal panel and body shell, make it sturdy and durable 4. Provides desktop-level monitoring in an in-ear monitoring and receiving system with a wireless range from 80 to 100m, and a frequency range of 550-580MHz. 5. The signal-to-noise ratio of the dynamic range is improved, so that the system has excellent anti-interference ability, and once again shows the good original soundTransmitter Specifications1. Case specification:Standard 1U Case 2. Material: Metal panel and body housing case 3. Frequency range: UHF550-580MHz 4. Frequency interval: 25MHz 5. Transmit output power:100mW(50 ohms) 6. Audio input: XLR & 6.3mm duplex outlet 7. Earphone output: 6.3mm jack, volume adjustable 8. Headphone load impedance: Greater than or equal to 16 ohms 9. Voltage current consumption: DC 12V 250mA 10. Antenna interface: TNC jack (50 ohms) 11. Size: 48 x 10.5 x 4.3cmReceiver Specifications1. Oscillation mode: PLL synthesized Frequency 2. Width Frequency range: UHF500-830MHz (Corresponding transmitter frequency) 3. Frequency interval: 25MHz 4. Operate mode: Manual adjust 5. Receiving mode: Single tuning. 6. Comprehensive Frequency Reaponse: 80Hz~15KHz+/-3dB 7. Output power (30 ohms): 2 x 35mW 8. Headphone load impedance: Greater than or equal to 16 ohms 9. Earphone output: 3.5mm jack 10. Power supply: 2 x AA batteries (not included) 11. Size: 8.5 x 6cm

Read more less

Features1. UHF wireless in-ear monitoring system. 2. A built-in limiter circuit for stage performances and a wide range of sounds eliminates distortion at excessive input levels. 3. Metal panel and body shell, makes it sturdy and durable 4. Provides desktop-level monitoring in an in-ear monitoring and receiving system with a wireless range from 80 to 100m, and a frequency range of 550-580MHz. 5. The signal-to-noise ratio of the dynamic range is improved, so that the system has excellent anti-interference ability, and once again shows the good original soundTransmitter Specifications1. Case specification:Standard 1U Case 2. Material: Metal panel and body housing case 3. Frequency range: UHF550-580MHz 4. Frequency interval: 25MHz 5. Transmit output power:100mW(50 ohms) 6. Audio input: XLR & 6.3mm duplex outlet 7. Earphone output: 6.3mm jack, volume adjustable 8. Headphone load impedance: Greater than or equal to 16 ohms 9. Voltage current consumption: DC 12V 250mA 10. Antenna interface: TNC jack (50 ohms) 11. Size: 48 x 10.5 x 4.3cmReceiver Specifications1. Oscillation mode: PLL synthesized Frequency 2. Width Frequency range: UHF550-580MHz (Corresponding transmitter frequency) 3. Frequency interval: 25MHz 4. Operate mode: Manual adjust 5. Receiving mode: Single tuning. 6. Comprehensive Frequency Response: 80Hz~15KHz+/-3dB 7. Output power (30 ohms): 2 x 35mW 8. Headphone load impedance: Greater than or equal to 16 ohms 9. Earphone output: 3.5mm jack 10. Power supply: 2 x AA batteries (not included) 11. Size: 8.5 x 6cm

Read more less

About The Product1. The wireless HDMI extender extends high-definition video and audio to any HDTV displays up to 330 feet away. It supports up to 4 displays to show one source content synchronously and resolutions up to 1080P.2. The extender transmits the real time video and audio signals with very low latency, allowing user to view the content in other rooms of the house, such as bedroom, living room, or kitchen. It also allows user to control source device from display side via source device’s remote controller. Features1. Digital 2.4G & 5GHz dual frequency wireless A/V transmission2. HDMI 1.4b (6.75Gbps), HDCP 1.4 and DVI compliant3. Full HD 1080P wireless transmission distance of up to 100m under open and interference-free conditions4. Powerful signal transmits through walls, floors, & ceilings5. Supports Point-to-Point and Multicast transmission (up to 4 receivers)6. Extends infrared remote to control source device from display side7. Support output loop back and 3D video transmission8. Simple Plug and Play, no software installation requiredparameter1. Video bandwidth: 7 Gbps2. Video resolution: up to 1080P 60Hz3. HDMI audio format: LPCM 2CH4. Wireless standard: 802.11a/b/g/n5. Modulation method: BPSK/QPSK/16-QAM/64-QAM6. Wireless frequency band: 2.4GHz, 5GHz ISM frequency band7. Operating range: up to 330 feet in open space8. Infrared frequency: 20KHz - 60KHz9. Transmitter:- Input: 1x HDMI Type-A (19-pin female)- Output: 1x HDMI Type-A(19-pin female) 1x USB (Mini USB Type) 1x IR output (3.5mm Stereo Mini-jack)10. Receiver:- Input: 1x USB (USB Type-A) 1x IR input (3.5mm stereo mini jack)- Output: 1x HDMI Type-A (19-pin female)- Dimensions: 100mmx100mmx25mm11. Power supply:- Input: AC100 - 240V 50/60Hz- Output: DC 5V/1A12. Power consumption: 3W (max)13. Working temperature: 32-104 Degree F / 0-40 Degree C14. Storage temperature: -4-140 Degree F / -20-60 Degree C15. Relative humidity: 20-90% RH (no condensation)Package List:- User manual x 1- USB power cable x 2- Power adapter x 2

Read more less