Electronics Modules

1. Type: Test Block2. Working frequency: High frequency3. Application: Integrated Circuit IC4. Contact impedance: Less than 25 milliohms5. Production process: Injection molding6. Features: Fire retardant/flame retardant7. Contact material: Beryllium copper shrapnel8. Insulator material: PEI, PPS9. Number of cores: 2010. Working temperature: -65～155 degrees Celsius11. Lead spacing: 0.65mm12. Service life: 20,000 times13. Adaptation chip body width: 4.4mmFeatures:1. Using double contact technology, the contact is more stable2. The seat shell is made of special engineering plastic, which has high strength and long life.3. The shrapnel adopts imported beryllium copper material, which has low impedance and good elasticity4. Thick gold plating layer, thick contact plating, ultra-low contact impedance, high reliabilitySpecification: Package Weight One Package Weight 0.02kgs / 0.05lb One Package Size 15cm * 12cm * 6cm / 5.91inch * 4.72inch * 2.36inch Qty per Carton 200 Carton Weight 5.00kgs / 11.02lb Carton Size 52cm * 36cm * 37cm / 20.47inch * 14.17inch * 14.57inch Loading Container 20GP: 385 cartons * 200 pcs = 77000 pcs 40HQ: 893 cartons * 200 pcs = 178600 pcs

Read more less

Overview1. XCore407I is an STM32 MCU core board that features the STM32F407IGT6 on board.2. Clock circuit, USB power management3. Onboard devices: USB HS PHY, Ethernet PHY, 1G Bit NandFlash4. Connectors：USB HS (mini / type A), USB FS (mini), Ethernet (RJ45)5. All the idle I/O ports are accessible on the pin headers6. 2.0mm pin header pitch, smaller size, easier to integrate into user system7. Note : please consider the EVK407I, which supports easily programing/debugging.What is On BoardSTM32F407IGT6 development board on board resource1. STM32F407IGT6: The high performance STM32 MCU which features:- Core: Cortex-M4 32-bit RISC- Feature: a full set of single-cycle DSP instructions- Operating Frequency: 168MHz, 210 DMIPS/1.25 DMIPS/MHz- Operating Voltage: 1.8V-3.6V- Package: LQFP176- Memories: 1024kB Flash, 192+4kB SRAM- MCU communication Interfaces:-- 3 x SPI, 4 x USART, 2 x UART, 2 x I2S, 3 x I2C-- 1 x FSMC, 1 x SDIO, 2 x CAN-- 1 x USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, ULPI and on-chip full-speed PHY-- 1 x 10/100 Ethernet MAC-- 1 x 8 to 14-bit parallel camera interface- AD & DA converters: 3 x AD (12-bit, 1μs, shares 24 channels); 2 x DA (12-bit)- Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP2. MIC2075-2, onboard USB FS power management device3. AMS1117-3.3, 3.3V voltage regulator4. K9F1G08U0E, 1G Bit NandFlash5. DP83848, Ethernet PHY6. MIC2075-1, onboard USB HS power management device7. USB3300, USB HS PHY8. Power supply switch, powered from 5Vin or USB connection9. Boot mode switch, for configuring BOOT0 pin10. Power indicator11. USB FS LED12. USB HS LED13. Reset button14. 8M crystal, MCU clock, enables the MCU run at higher speed by frequency multiplication15. 24M crystal, USB3300 clock16. 50M crystal, DP83848 clock17. 32.768K crystal, for internal RTC with calibration18. Ethernet connector19. USB FS mini connector20. USB HS mini connector21. USB HS type A connector22. MCU pins expander, VCC, GND and all the idle I/O ports are accessible on expansion connectors for further expansion23. USB OTG/HOST jumper24. VREF/VBAT jumper25. Ethernet I/O selection solder joint26. USB HS I/O selection solder joint27. PDR selection solder joint: 1.8-3.6V, -40～105℃ OR 1.7-3.6V, 0～70℃Package Contents1. XCore407I development board x 12. USB type A to Mini-B cable x 13. Software CD x 1Specification: Package Weight One Package Weight 0.15kgs / 0.33lb One Package Size 15cm * 8cm * 3cm / 5.91inch * 3.15inch * 1.18inch Qty per Carton 260 Carton Weight 15.00kgs / 33.07lb Carton Size 60cm * 40cm * 39cm / 23.62inch * 15.75inch * 15.35inch Loading Container 20GP: 284 cartons * 260 pcs = 73840 pcs 40HQ: 661 cartons * 260 pcs = 171860 pcs

Read more less

OverviewCore103V is a small STM32 development board that features an STM32F103VET6 device as the microcontroller, supports further expansion. It is ideal for starting application development with STM32F family.As a minimal ready-to-run system, the Core103V integrates USB communication interface, JTAG/SWD programming/debugging interface, clock circuit, boot mode selection, and so on.Furthermore, pin headers on the backside allow the Core103V to be plugged-in your application board and act as the MCU core circuit in your system. All the I/O ports are accessible on the pin headers, and the header pitch is designed as 2.54mm.What is On BoardSTM32F103VET6 development board on board resource1. STM32F103VET6: The high performance STM32 MCU which features:- Core: Cortex-M3 32-bit RISC- Operating Frequency: 72MHz, 1.25 DMIPS/MHz- Operating Voltage: 2-3.6V- Package: LQFP100- I/Os: 80- Memories: 512kB Flash, 64kB RAM- MCU communication Interfaces:-- 3 x SPI, 5 x USART, 2 x I2S, 2 x I2C, 1 x FSMC, 1 x LCD, 1 x SDIO, 1 x USB, 1 x CAN- AD & DA converters: 3 x AD (12-bit, 1μs, shares 16 channels); 2 x DA (12-bit)- Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP2. AMS1117-3.3 (on bottom side): 3.3V voltage regulator3. Power supply switch, powered from 5Vin or USB connection4. Boot mode selection, for configuring BOOT0 pin5. Boot mode selection (on bottom side), for configuring BOOT1 pin6. Power indicator7. VBUS LED8. Reset button9. 8M crystal oscillator10. 32.768K crystal (on bottom side), for internal RTC with calibration11. JTAG/SWD interface: for debugging/programming12. USB connector, used for establishing USB communication between PC and the STM32 development board13. IO expander (including VCC/GND), all the I/O pins are accessible on expansion connectors for further expansion14. 5V in pinheader, 5V power supply input15. USB enable jumper- Short the jumper to enable USB function- Open the jumper to disable, as well as taking up no I/O port16. VBAT selection jumper- Short the jumper to use system power supply- Open the jumper to connect the VBAT to external power, such as battery17. VREF selection jumper- Short the jumper to connect VREF+/VREF- to VCC/GND- Open the jumper to connect VREF+/VREF- to other custom pin via jumper wirePackage Contents1. Core103V development board x 12. USB type A to Mini-B cable x 13. Software CD x 1Specification: Package Weight One Package Weight 0.12kgs / 0.26lb One Package Size 12cm * 6cm * 3cm / 4.72inch * 2.36inch * 1.18inch Qty per Carton 390 Carton Weight 15.00kgs / 33.07lb Carton Size 60cm * 36cm * 39cm / 23.62inch * 14.17inch * 15.35inch Loading Container 20GP: 316 cartons * 390 pcs = 123240 pcs 40HQ: 734 cartons * 390 pcs = 286260 pcs

Read more less

Overview1. Core405R is an STM32 MCU core board designed for STM32F405RGT6, supports further expansion. It is ideal for starting application development with STM32F family.2. Minimal ready-to-run system, integrates clock circuit, USB control circuit, USB connector, 3. etc.3. All the I/O ports are accessible on the pin headers4. JTAG/SWD programming/debugging interface5. 2.54mm header pitch, allowed to be plugged-in your application boardWhat has On Board1. STM32F405RGT6: The high performance STM32 MCU which features:- Core: Cortex-M4 32-bit RISC- Operating Frequency: 168MHz, 210 DMIPS/1.25 DMIPS/MHz- Operating Voltage: 1.8V-3.6V- Package: LQFP64- Memories: 1MB Flash, 192+4kB SRAM- MCU communication Interfaces:-- 3 x SPI, 4 x USART, 2 x UART, 2 x I2S, 3 x I2C, 1 x SDIO, 2 x CAN--1 x USB 2.0 HS/FS device/host/OTG controller with dedicated DMA, on-chip full-speed PHY--1 x USB HS ULPI (external PHY required)- AD & DA converters: 3 x AD (12-bit, 1μs, shares 16 channels); 2 x DA (12-bit)- Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP2. AMS1117-3.3: 3.3V voltage regulator3. MIC2075-2: onboard USB power management device4. Power supply switch, powered from 5Vin or USB connection5. Boot mode selection, for configuring BOOT0 pin6. Power indicator7. VBUS LED8. Reset button9. 8M crystal10. 32.768K crystal, for internal RTC with calibration11. JTAG/SWD interface: for debugging/programming12. USB connector, used for establishing USB communication between PC and the STM32 development board13. MCU pins expander, VCC, GND and all the I/O pins are accessible on expansion connectors for further expansion14. 5Vin pinheader, 5V power supply is required when using USB HOST/OTG15. USB jumper- Short the jumper when using USB- Open the jumper to disconnect from related I/O port16. VBAT selection jumper- Short the jumper to use system power supply- Open the jumper to connect the VBAT to external power, such as batteryPackage Contents1. Core405R x 12. USB type A to Mini-B cable x 13. Software CD x 1Specification: Package Weight One Package Weight 0.12kgs / 0.26lb One Package Size 10cm * 8cm * 3cm / 3.94inch * 3.15inch * 1.18inch Qty per Carton 390 Carton Weight 15.00kgs / 33.07lb Carton Size 60cm * 40cm * 39cm / 23.62inch * 15.75inch * 15.35inch Loading Container 20GP: 284 cartons * 390 pcs = 110760 pcs 40HQ: 661 cartons * 390 pcs = 257790 pcs

Read more less

STM32 development board designed for STM32F429I, features the STM32F429IGT6 MCU, and integrates various standard interfaces, pretty easy for peripheral expansions.Overview1. Open429I-C is an STM32 development board designed for the STM32F429IGT6 microcontroller, consists of the mother board and the MCU core board Core429I.2. The Open429I-C supports further expansion with various optional accessory boards for specific application. The modular and open design makes it the ideal for starting application development with STM32 series microcontrollers.What has on the mother board1. MCU core board connector: for easily connecting the Core429I2. USART3 interface: easily connects to RS232, RS485, USB TO 232, etc.3. DCMI interface: for connecting camera4. Capacitive touch panel interface: for connecting capacitive touch panel5. CAN2 interface: for connecting CAN modules6. CAN1 interface: for connecting CAN modules7. SDIO interface: for connecting Micro SD module, features much faster access speed rather than SPI8. ULPI interface: for connecting high-speed USB peripheral (the STM32F429I integrates USB HS controller without any PHY device)9. LCD interface 1: for connecting 7inch LCD10. ONE-WIRE interface: easily connects to ONE-WIRE devices (TO-92 package), such as temperature sensor (DS18B20), electronic registration number (DS2401), etc.11. LCD interface 2: for connecting 4.3inch LCD12. I2C2/I2C3 interface: easily connects to I2C peripherals such as I/O expander (PCF8574), EEPROM (AT24Cxx), etc.13. SAI1 interface: for connecting audio modules like UDA1380 module14. Ethernet interface: for connecting Ethernet modules15. USB connector: USB to UART via the onboard convertor PL230316. SPI1/SPI2 interfaces:- Easily connects to SPI peripherals such as DataFlash (AT45DBxx), SD card, MP3 module, etc.- Easily connects to AD/DA modules (SPI1 features AD/DA alternative function)17. I2S2/I2S3/I2C1 interface: easily connects to I2S peripherals such as audio module, etc.18. 8-bit FMC interface: easily connects to peripherals such as NandFlash19. 5V DC jack20. 5V/3.3V power input/output: usually used as power output, also common-grounding with other user board21. MCU pins connector: all the MCU I/O ports are accessible on expansion connectors for further expansion22. PL2303: USB to UART convertor23. LEDs: convenient for indicating I/O status and/or program running state24. PL2303 TX-LED / RX-LED25. 12MHz crystal: for PL230326. Joystick: five positions27. WAKE UP button: used as regular button, and/or wake up the STM32 MCU from sleep28. USB to UART jumper29. LED jumper- Short the jumper to connect to default I/Os used in example code- Open the jumper to connect to custom I/Os via jumper wires30. Button/Joystick jumper- Short the jumper to connect to default I/Os used in example code- Open the jumper to connect to custom I/Os via jumper wiresPackage Contains1. Open429I-C development board x 12. USB type A plug to mini-B plug cable x 13. USB type A receptacle to mini-B plug cable x 14. 4-pin 2-pin wires pack x 15. USB power cable x 16. Software CD x 1Specification: Package Weight One Package Weight 0.55kgs / 1.22lb One Package Size 25cm * 19cm * 11cm / 9.84inch * 7.48inch * 4.33inch Qty per Carton 20 Carton Weight 12.00kgs / 26.46lb Carton Size 56cm * 37cm * 50cm / 22.05inch * 14.57inch * 19.69inch Loading Container 20GP: 257 cartons * 20 pcs = 5140 pcs 40HQ: 597 cartons * 20 pcs = 11940 pcs

Read more less

Overview1. Open429I-C is an STM32 development board designed for the STM32F429IGT6 microcontroller, consists of the mother board and the MCU core board Core429I.2. The Open429I-C supports further expansion with various optional accessory boards for specific application. The modular and open design makes it the ideal for starting application development with STM32 series microcontrollers.What has on the mother board1. MCU core board connector: for easily connecting the Core429I2. USART3 interface: easily connects to RS232, RS485, USB TO 232, etc.3. DCMI interface: for connecting camera4. Capacitive touch panel interface: for connecting capacitive touch panel5. CAN2 interface: for connecting CAN modules6. CAN1 interface: for connecting CAN modules7. SDIO interface: for connecting Micro SD module, features much faster access speed rather than SPI8. ULPI interface: for connecting high-speed USB peripheral (the 9. STM32F429I integrates USB HS controller without any PHY device)10. LCD interface 1: for connecting 7inch LCD11. ONE-WIRE interface: easily connects to ONE-WIRE devices (TO-92 package), such as temperature sensor (DS18B20), electronic registration number (DS2401), etc.12. LCD interface 2: for connecting 4.3inch LCD13. I2C2/I2C3 interface: easily connects to I2C peripherals such as I/O expander (PCF8574), EEPROM (AT24Cxx), etc.14. SAI1 interface: for connecting audio modules like UDA1380 module15. Ethernet interface: for connecting Ethernet modules16. USB connector: USB to UART via the onboard convertor PL2303SPI1/SPI2 interfaces:- Easily connects to SPI peripherals such as DataFlash (AT45DBxx), SD card, MP3 module, etc.- Easily connects to AD/DA modules (SPI1 features AD/DA alternative function)17. I2S2/I2S3/I2C1 interface: easily connects to I2S peripherals such as audio module, etc.18. 8-bit FMC interface: easily connects to peripherals such as NandFlash19. 5V DC jack20. 5V/3.3V power input/output: usually used as power output, also common-grounding with other user board21. MCU pins connector: all the MCU I/O ports are accessible on expansion connectors for further expansion22. PL2303: USB to UART convertor23. LEDs: convenient for indicating I/O status and/or program running state24. PL2303 TX-LED / RX-LED25. 12MHz crystal: for PL230326. Joystick: five positions27. WAKE UP button: used as regular button, and/or wake up the STM32 MCU from sleep28. USB to UART jumper29. LED jumper- Short the jumper to connect to default I/Os used in example code- Open the jumper to connect to custom I/Os via jumper wires30. Button/Joystick jumper- Short the jumper to connect to default I/Os used in example code- Open the jumper to connect to custom I/Os via jumper wiresThe "Standard Package" and "Accessory Boards Package" below are included.Standard Package1. Open429I-C development board x 12. USB type A plug to mini-B plug cable x 13. USB type A receptacle to mini-B plug cable x 14. 4-pin 2-pin wires pack x 15. USB power cable x 16. Software CD x 1Accessory Boards Package1. 4.3 inch 480x272 Touch LCD (B) x 12. DP83848 Ethernet Board x 13. USB3300 USB HS Board x 14. NandFlash Board (A) x 15. UDA1380 Board x 16. Micro SD Storage Board x 17. OV2640 Camera Board x 18. Ethernet Cable x 19. 4.3 inch LCD screws pack x 1Specification: Package Weight One Package Weight 0.49kgs / 1.08lb One Package Size 10cm * 8cm * 3cm / 3.94inch * 3.15inch * 1.18inch Qty per Carton 390 Carton Weight 15.00kgs / 33.07lb Carton Size 60cm * 40cm * 39cm / 23.62inch * 15.75inch * 15.35inch Loading Container 20GP: 284 cartons * 390 pcs = 110760 pcs 40HQ: 661 cartons * 390 pcs = 257790 pcs

Read more less

NUCLEO-L476RG DescriptionThe STM32 Nucleo board provides an affordable and flexible way for users to try out new ideas and build prototypes with any STM32 microcontroller line, choosing from the various combinations of performance, power consumption and features. The Arduino? connectivity support and ST Morpho headers make it easy to expand the functionality of the STM32 Nucleo open development platform with a wide choice of specialized shields.The STM32 Nucleo board does not require any separate probe as it integrates the ST-LINK/V2-1 debugger and programmer.The STM32 Nucleo board comes with the STM32 comprehensive software HAL library together with various packaged software examples, as well as direct access to mbed online resources.NUCLEO-L476RG Key FeaturesSTM32 microcontroller with LQFP64 packageTwo types of extension resourcesArduino Uno Revision 3 connectivitySTMicroelectronics Morpho extension pin headers for full access to all STM32 I/Osmbed-enabled (http://mbed.org)On-board ST-LINK/V2-1 debugger/programmer with SWD connectorselection-mode switch to use the kit as a standalone ST-LINK/V2-1Flexible board power supplyUSB VBUS or external source(3.3 V, 5 V, 7 - 12 V)Power management access pointThree LEDsUSB communication (LD1), user LED (LD2), power LED (LD3)Two push buttons: USER and RESETUSB re-enumeration capability: three different interfaces supported on USBVirtual Com portMass storageDebug portSupported by wide choice of Integrated Development Environments (IDEs) including IAR?, Keil?, GCC-based IDEsSpecification: Package Weight One Package Weight 0.11kgs / 0.25lb One Package Size 10cm * 9cm * 5cm / 3.94inch * 3.54inch * 1.97inch Qty per Carton 192 Carton Weight 15.00kgs / 33.07lb Carton Size 60cm * 36cm * 40cm / 23.62inch * 14.17inch * 15.75inch Loading Container 20GP: 308 cartons * 192 pcs = 59136 pcs 40HQ: 716 cartons * 192 pcs = 137472 pcs

Read more less

Features1. Onboard unibody power supply isolation, provides stable isolated voltage, needs no extra power supply for the isolated terminal 2. Onboard photocoupler isolation, prevent interference from external high-voltage circuit connected to the relay 3. High quality relay, contact rating: 10A 250V AC or Less than or equal 10A 30V DC 4. ABS protection enclosure with rail-mount support, easy to install, safe to use 5. Breakout USB port and BOOT pin, make it easy to debug without disassembling the enclosure 6. PWR indicator, RGB LED, and passive buzzer outside the enclosure 7. Come with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples)Specification1. Operation voltage: 5V 2. Relay channel: 8CH 3. Communication protocol: USB 4. Contact form: 1NO 1NC 5. Communication interface: Micro USBPackage List1. ABS protection enclosure (top and bottom) x 1 2. Pico-Relay-B x 1 3. Screwdriver x 1 4. Screws pack x 1Specification: Package Weight One Package Weight 0.32kgs / 0.70lb One Package Size 16cm * 12cm * 5cm / 6.3inch * 4.72inch * 1.97inch Qty per Carton 40 Carton Weight 11.50kgs / 25.35lb Carton Size 50cm * 32cm * 27cm / 19.69inch * 12.6inch * 10.63inch Loading Container 20GP: 617 cartons * 40 pcs = 24680 pcs 40HQ: 1432 cartons * 40 pcs = 57280 pcs

Read more less

Specification1. USB: - USB 2.0 x 2 - USB 2.0 x 2 (via FFC connector) 2. GPIO: Raspberry Pi 40 PIN GPIO x 1 3. Header: M.2 slot x 1 4. HD media interface: HDMI x 2, 1x via FFC connector, support 4K 30fps output 5. DSI display: MIPI DSI x 1 (15pin 1.0mm FPC) 6. CSI camera: MIPI CSI-2 x 2 (15pin 1.0mm FPC) 7. Power input: 5V 8. FAN: 5V / 12V (no fan control) 9. RJ45 Ethernet: Gigabit Ethernet 10. CM4 slot: Suitable for all variants of Compute Module 4 11. SD card slot: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 12. Size: 85.0 x 56.0mmPackage List1. CM4-IO-BASE-B x 1 2. Metal case (top and bottom) x 1 3. Fan-4010-PWM-5V x 1 4. Screwdriver x 1 5. Screws pack x 1 6. 5V 3A USB-C power adapter x 1Specification: Package Weight One Package Weight 0.46kgs / 1.01lb One Package Size 16cm * 12cm * 5cm / 6.3inch * 4.72inch * 1.97inch Qty per Carton 40 Carton Weight 16.50kgs / 36.38lb Carton Size 50cm * 32cm * 27cm / 19.69inch * 12.6inch * 10.63inch Loading Container 20GP: 617 cartons * 40 pcs = 24680 pcs 40HQ: 1432 cartons * 40 pcs = 57280 pcs

Read more less

Specification1. USB: - USB 2.0 x 2 - USB 2.0 x 2 (via FFC connector) 2. GPIO: Raspberry Pi 40 PIN GPIO x 1 3. Header: M.2 slot x 1 4. HD media interface: HDMI x 2, 1x via FFC connector, support 4K 30fps output 5. DSI display: MIPI DSI x 1 (15pin 1.0mm FPC) 6. CSI camera: MIPI CSI-2 x 2 (15pin 1.0mm FPC) 7. Power input: 5V 8. FAN: 5V / 12V (no fan control) 9. RJ45 Ethernet: Gigabit Ethernet 10. CM4 slot: Suitable for all variants of Compute Module 4 11. SD card slot: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 12. Size: 85.0 x 56.0mmPackage List1. CM4-IO-BASE-B x 1 2. Metal case (top and bottom) x 1 3. Fan-4010-PWM-5V x 1 4. Screwdriver x 1 5. Screws pack x 1 6. 5V 3A USB-C power adapter x 1Specification: Package Weight One Package Weight 0.41kgs / 0.89lb One Package Size 16cm * 12cm * 5cm / 6.3inch * 4.72inch * 1.97inch Qty per Carton 40 Carton Weight 16.50kgs / 36.38lb Carton Size 50cm * 32cm * 27cm / 19.69inch * 12.6inch * 10.63inch Loading Container 20GP: 617 cartons * 40 pcs = 24680 pcs 40HQ: 1432 cartons * 40 pcs = 57280 pcs

Read more less

Specification1. USB: USB 3.2 Gen1 x 3 2. GPIO: Raspberry Pi 40 PIN GPIO x 1 3. HD media interface: HDMI x 2, support 4K 30fps output 4. DSI display: MIPI DSI x 2 (15pin 1.0mm FPC) 5. CSI camera: MIPI CSI-2 x 2 (15pin 1.0mm FPC) 6. Power input: 7V - 36V 7. FAN: 5V / 12V (Allows speed adjustment and measurement) 8. RTC: Real-time clock with battery socket and ability to wake Compute Module 4 9. RJ45 Ethernet: Dual Gigabit Ethernet 10. CM4 slot: Suitable for all variants of Compute Module 4 11. SD card slot: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 12. Size:109.0 x 91.5mmPackage List1. CM4-DUAL-ETH-BASE x 1 2. Metal case (top and bottom) x 1 3. Fan-4010-PWM-12V x 1 4. Screwdriver x 1 5. Screws pack x 1 6. 12V 2A power adapter x 1Specification: Package Weight One Package Weight 0.54kgs / 1.19lb One Package Size 16cm * 12cm * 5cm / 6.3inch * 4.72inch * 1.97inch Qty per Carton 40 Carton Weight 18.00kgs / 39.68lb Carton Size 50cm * 32cm * 27cm / 19.69inch * 12.6inch * 10.63inch Loading Container 20GP: 617 cartons * 40 pcs = 24680 pcs 40HQ: 1432 cartons * 40 pcs = 57280 pcs

Read more less

Specification1. USB: USB 3.2 Gen1 x 3 2. GPIO: Raspberry Pi 40 PIN GPIO x 1 3. HD media interface: HDMI x 2, support 4K 30fps output 4. DSI display: MIPI DSI x 2 (15pin 1.0mm FPC) 5. CSI camera: MIPI CSI-2 x 2 (15pin 1.0mm FPC) 6. Power input: 7V - 36V 7. FAN: 5V / 12V (Allows speed adjustment and measurement) 8. RTC: Real-time clock with battery socket and ability to wake Compute Module 4 9. RJ45 Ethernet: Dual Gigabit Ethernet 10. CM4 slot: Suitable for all variants of Compute Module 4 11. SD card slot: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 12. Size:109.0 x 91.5mmPackage List1. CM4-DUAL-ETH-BASE x 1 2. Metal case (top and bottom) x 1 3. Fan-4010-PWM-12V x 1 4. Screwdriver x 1 5. Screws pack x 1 6. 12V 2A power adapter x 1Specification: Package Weight One Package Weight 0.45kgs / 0.98lb One Package Size 16cm * 12cm * 5cm / 6.3inch * 4.72inch * 1.97inch Qty per Carton 40 Carton Weight 18.00kgs / 39.68lb Carton Size 50cm * 32cm * 27cm / 19.69inch * 12.6inch * 10.63inch Loading Container 20GP: 617 cartons * 40 pcs = 24680 pcs 40HQ: 1432 cartons * 40 pcs = 57280 pcs

Read more less

Specification1. USB: - USB 2.0 x 2 - USB 2.0 x 2 (via FFC connector) 2. GPIO: Raspberry Pi 40 PIN GPIO x 1 3. Header: M.2 slot x 1 4. HD media interface: HDMI x 2, 1x via FFC connector, support 4K 30fps output 5. DSI display: MIPI DSI x 1 (15pin 1.0mm FPC) 6. CSI camera: MIPI CSI-2 x 2 (15pin 1.0mm FPC) 7. Power input: 5V 8. FAN: 5V / 12V (no fan control) 9. RJ45 Ethernet: Gigabit Ethernet 10. CM4 slot: Suitable for all variants of Compute Module 4 11. SD card slot: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 12. Size: 85.0 x 56.0mmPackage List1. CM4-IO-BASE-A x 1 2. Metal case (top and bottom) x 1 3. Fan-4010-PWM-5V x 1 4. Screwdriver x 1 5. Screws pack x 1 6. 5V 3A USB-C power adapter x 1Specification: Package Weight One Package Weight 0.41kgs / 0.89lb One Package Size 16cm * 12cm * 5cm / 6.3inch * 4.72inch * 1.97inch Qty per Carton 40 Carton Weight 16.50kgs / 36.38lb Carton Size 50cm * 32cm * 27cm / 19.69inch * 12.6inch * 10.63inch Loading Container 20GP: 617 cartons * 40 pcs = 24680 pcs 40HQ: 1432 cartons * 40 pcs = 57280 pcs

Read more less

Specification1. POE: Integrates 802.3af-compliant PoE circuit (5V/2.5A) 2. USB: USB 2.0 x 4 3. GPIO: Raspberry Pi 40 PIN GPIO x 1 4. Header: - RS485 x 1 - RS232 x 1 - PCIe Gen 2 x 1 5. HD media interface: HDMI x 2, supports 4K 30fps output 6. DSI display: MIPI DSI x 2 (15pin 1.0mm FPC) 7. CSI camera: MIPI CSI-2 x 2 (15pin 1.0mm FPC) 8. Power input: 5V 9. FAN: 5V / 12V (Allows speed adjustment and measurement) 10. RTC: Real-time clock with battery socket and ability to wake Compute Module 4 11. RJ45 Ethernet: Gigabit Ethernet 12. CM4 slot: Suitable for all variants of Compute Module 4 13. SD card slot: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 14. Size: 124.50 x 108.80mmPackage List1. Compute Module 4 PoE Board (B) x 1 2. Metal case (top and bottom) x 1 3. Fan-4010-PWM-12V x 1 4. Screwdriver x 1 5. Screws pack x 1 6. 5V 3A USB-C power adapter x 1Specification: Package Weight One Package Weight 0.51kgs / 1.11lb One Package Size 16cm * 12cm * 5cm / 6.3inch * 4.72inch * 1.97inch Qty per Carton 40 Carton Weight 19.50kgs / 42.99lb Carton Size 50cm * 32cm * 27cm / 19.69inch * 12.6inch * 10.63inch Loading Container 20GP: 617 cartons * 40 pcs = 24680 pcs 40HQ: 1432 cartons * 40 pcs = 57280 pcs

Read more less

Specification1. USB: - USB 2.0 x 2 - USB 2.0 x 2 (via FFC connector) 2. GPIO: Raspberry Pi 40 PIN GPIO x 1 3. Header: M.2 slot x 1 4. HD media interface: HDMI x 2, 1x via FFC connector, support 4K 30fps output 5. DSI display: MIPI DSI x 1 (15pin 1.0mm FPC) 6. CSI camera: MIPI CSI-2 x 2 (15pin 1.0mm FPC) 7. Power input: 5V 8. FAN: 5V / 12V (no fan control) 9. RJ45 Ethernet: Gigabit Ethernet 10. CM4 slot: Suitable for all variants of Compute Module 4 11. SD card slot: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 12. Size: 85.0 x 56.0mmPackage List1. CM4-IO-BASE-A x 1 2. Metal case (top and bottom) x 1 3. Fan-4010-PWM-5V x 1 4. Screwdriver x 1 5. Screws pack x 1 6. 5V 3A USB-C power adapter x 1Specification: Package Weight One Package Weight 0.41kgs / 0.89lb One Package Size 16cm * 12cm * 5cm / 6.3inch * 4.72inch * 1.97inch Qty per Carton 40 Carton Weight 16.50kgs / 36.38lb Carton Size 50cm * 32cm * 27cm / 19.69inch * 12.6inch * 10.63inch Loading Container 20GP: 617 cartons * 40 pcs = 24680 pcs 40HQ: 1432 cartons * 40 pcs = 57280 pcs

Read more less

Specification1. POE: Integrates 802.3af-compliant PoE circuit (5V/2.5A) 2. USB: USB 2.0 x 4 3. GPIO: Raspberry Pi 40 PIN GPIO x 1 4. Header: - RS485 x 1 - RS232 x 1 - PCIe Gen 2 x 1 5. HD media interface: HDMI x 2, supports 4K 30fps output 6. DSI display: MIPI DSI x 2 (15pin 1.0mm FPC) 7. CSI camera: MIPI CSI-2 x 2 (15pin 1.0mm FPC) 8. Power input: 5V 9. FAN: 5V / 12V (Allows speed adjustment and measurement) 10. RTC: Real-time clock with battery socket and ability to wake Compute Module 4 11. RJ45 Ethernet: Gigabit Ethernet 12. CM4 slot: Suitable for all variants of Compute Module 4 13. SD card slot: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 14. Size: 124.50 x 108.80mmPackage List1. Compute Module 4 PoE Board (B) x 1 2. Metal case (top and bottom) x 1 3. Fan-4010-PWM-12V x 1 4. Screwdriver x 1 5. Screws pack x 1 6. 5V 3A USB-C power adapter x 1Specification: Package Weight One Package Weight 0.51kgs / 1.11lb One Package Size 16cm * 12cm * 5cm / 6.3inch * 4.72inch * 1.97inch Qty per Carton 40 Carton Weight 19.50kgs / 42.99lb Carton Size 50cm * 32cm * 27cm / 19.69inch * 12.6inch * 10.63inch Loading Container 20GP: 617 cartons * 40 pcs = 24680 pcs 40HQ: 1432 cartons * 40 pcs = 57280 pcs

Read more less

1. USB: - USB 2.0 x 2 - USB 2.0 x 2 (via FFC connector) 2. GPIO: Raspberry Pi 40 PIN GPIO x 1 3. Header: M.2 slot x 1 4. HD media interface: HDMI x 2, 1x via FFC connector, support 4K 30fps output 5. DSI display: MIPI DSI x 1 (15pin 1.0mm FPC) 6. CSI camera: MIPI CSI-2 x 2 (15pin 1.0mm FPC) 7. Power input: 5V 8. FAN: 5V / 12V (no fan control) 9. RJ45 Ethernet: Gigabit Ethernet 10. CM4 slot: Suitable for all variants of Compute Module 4 11. SD card slot: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 12. Size: 85.0 x 56.0mmSpecification: Package Weight One Package Weight 0.07kgs / 0.16lb One Package Size 15cm * 12cm * 2cm / 5.91inch * 4.72inch * 0.79inch Qty per Carton 200 Carton Weight 12.60kgs / 27.78lb Carton Size 46cm * 32cm * 32cm / 18.11inch * 12.6inch * 12.6inch Loading Container 20GP: 566 cartons * 200 pcs = 113200 pcs 40HQ: 1314 cartons * 200 pcs = 262800 pcs

Read more less

1. CM4 Socket: Suitable for all variants of Compute Module 4 2. Networking: - Dual Gigabit Ethernet RJ45 - M.2 B KEY, for connecting 5G / 4G module - Nano-SIM card slot, supports standard Nano-SIM card for 5G/4G/3G/2G communication 3. USB: USB 3.2 Gen1 x 2 4. PIN header: Raspberry Pi 40PIN GPIO header 5. Display: MIPI DSI port (15pin 1.0mm FPC connector) 6. Camera: MIPI CSI-2 port x 2 (15pin 1.0mm FPC connector) 7. Video: HDMI x 2, supports 4K 30fps output 8. RTC: Real-time clock with battery socket and ability to wake Compute Module 4 9. Storage: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 10. FAN HEADER: 5V/12V (12V by default), allows speed adjustment and measurement 11. Power input: 5V/2.5A 12. Size: 99.6 x 87.0mmSpecification: Package Weight One Package Weight 0.44kgs / 0.98lb One Package Size 16cm * 12cm * 5cm / 6.3inch * 4.72inch * 1.97inch Qty per Carton 40 Carton Weight 15.00kgs / 33.07lb Carton Size 50cm * 32cm * 27cm / 19.69inch * 12.6inch * 10.63inch Loading Container 20GP: 617 cartons * 40 pcs = 24680 pcs 40HQ: 1432 cartons * 40 pcs = 57280 pcs

Read more less

1. CM4 Socket: Suitable for all variants of Compute Module 4 2. Networking: - Dual Gigabit Ethernet RJ45 - M.2 B KEY, for connecting 5G / 4G module - Nano-SIM card slot, supports standard Nano-SIM card for 5G/4G/3G/2G communication 3. USB: USB 3.2 Gen1 x 2 4. PIN header: Raspberry Pi 40PIN GPIO header 5. Display: MIPI DSI port (15pin 1.0mm FPC connector) 6. Camera: MIPI CSI-2 port x 2 (15pin 1.0mm FPC connector) 7. Video: HDMI x 2, supports 4K 30fps output 8. RTC: Real-time clock with battery socket and ability to wake Compute Module 4 9. Storage: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 10. FAN HEADER: 5V/12V (12V by default), allows speed adjustment and measurement 11. Power input: 5V/2.5A 12. Size: 99.6 x 87.0mmSpecification: Package Weight One Package Weight 0.45kgs / 0.98lb One Package Size 16cm * 12cm * 5cm / 6.3inch * 4.72inch * 1.97inch Qty per Carton 40 Carton Weight 15.00kgs / 33.07lb Carton Size 50cm * 32cm * 27cm / 19.69inch * 12.6inch * 10.63inch Loading Container 20GP: 617 cartons * 40 pcs = 24680 pcs 40HQ: 1432 cartons * 40 pcs = 57280 pcs

Read more less

About The ProtuctThis is an industrial expansion module based on Raspberry Pi CM4, which features common interfaces such as Gigabit Ethernet, HDMI, USB, and GPIO, allows additional 4G / 5G / LoRa wireless communication modules to be connected via the M.2 or Mini-PCIe socket. There are also industrial interfaces/resources including RS485, CAN, and RTC. Combined with the industrial rail-mount protection case, the module is an ideal choice for building IoT gateway, 4G/5G router, IoT data acquisition, or even the PLC device in industrial automatic control system, and more.Specifications1. CM4 socket: For all variants of Compute Module 4 2. Networking: - Gigabit Ethernet RJ45 - M.2 B KEY / Mini-PCIe (via adapter), for connecting 5G / 4G / LoRa wireless module - Nano-SIM card slot, support standard Nano-SIM card for 5G/4G/3G/2G communication 3. USB: USB 2.0 x 3 4. PIN header: Non-isolated RS485 x 2, non-isolated CAN x 1, some GPIO pins 5. Camera: MIPI CSI-2 x 1 (15pin 1.0mm FPC connector) 6. Video: HDMI x 1, support 4K 30fps output 7. RTC: Real-time clock with battery socket and ability to wake Compute Module 4 8. Storage: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 9. Fan header: 5V/12V, allows speed adjustment and measurement 10. Power input: 5V or 7~36V 11. Dimensions: 145 x 90 x 40mmPackage List1. CM4-IO-WIRELESS-BASE x 1 2. PCIe to 4G/LoRa adapter x 1 3. Screwdriver x 1 4. Screws pack x 1 5. 12V 2A power adapter x 1Specification: Package Weight One Package Weight 0.38kgs / 0.83lb One Package Size 16cm * 12cm * 5cm / 6.3inch * 4.72inch * 1.97inch Qty per Carton 40 Carton Weight 15.50kgs / 34.17lb Carton Size 50cm * 32cm * 27cm / 19.69inch * 12.6inch * 10.63inch Loading Container 20GP: 617 cartons * 40 pcs = 24680 pcs 40HQ: 1432 cartons * 40 pcs = 57280 pcs

Read more less

About The ProtuctThis is an industrial expansion module based on Raspberry Pi CM4, which features common interfaces such as Gigabit Ethernet, HDMI, USB, and GPIO, allows additional 4G / 5G / LoRa wireless communication modules to be connected via the M.2 or Mini-PCIe socket. There are also industrial interfaces/resources including RS485, CAN, and RTC. Combined with the industrial rail-mount protection case, the module is an ideal choice for building IoT gateway, 4G/5G router, IoT data acquisition, or even the PLC device in industrial automatic control system, and more.Specifications1. CM4 socket: For all variants of Compute Module 4 2. Networking: - Gigabit Ethernet RJ45 - M.2 B KEY / Mini-PCIe (via adapter), for connecting 5G / 4G / LoRa wireless module - Nano-SIM card slot, support standard Nano-SIM card for 5G/4G/3G/2G communication 3. USB: USB 2.0 x 3 4. PIN header: Non-isolated RS485 x 2, non-isolated CAN x 1, some GPIO pins 5. Camera: MIPI CSI-2 x 1 (15pin 1.0mm FPC connector) 6. Video: HDMI x 1, support 4K 30fps output 7. RTC: Real-time clock with battery socket and ability to wake Compute Module 4 8. Storage: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 9. Fan header: 5V/12V, allows speed adjustment and measurement 10. Power input: 5V or 7~36V 11. Dimensions: 145 x 90 x 40mmPackage List1. CM4-IO-WIRELESS-BASE x 1 2. PCIe to 4G/LoRa adapter x 1 3. Screwdriver x 1 4. Screws pack x 1 5. 12V 2A power adapter x 1Specification: Package Weight One Package Weight 0.38kgs / 0.83lb One Package Size 16cm * 12cm * 5cm / 6.3inch * 4.72inch * 1.97inch Qty per Carton 40 Carton Weight 15.50kgs / 34.17lb Carton Size 50cm * 32cm * 27cm / 19.69inch * 12.6inch * 10.63inch Loading Container 20GP: 617 cartons * 40 pcs = 24680 pcs 40HQ: 1432 cartons * 40 pcs = 57280 pcs

Read more less

FeaturesThe Compute Module PoE Board is a development board that you can plug a Raspberry Pi Compute Module into, and make use of the resources of Pi more flexibly. With the PoE (Power over Ethernet) feature, and versatile onboard peripheral interfaces, it is suitable for evaluating the Raspberry Pi compute module, also is an ideal choice for end products. 1. Raspberry Pi GPIO header, for connecting sorts of Raspberry Pi HATs. 2. 10/100M auto-negotiation Ethernet port, with PoE enabled. 3. 4 x USB ports, which allows connecting more USB devices. 4. 2 x CSI camera interfaces. 5. Onboard HDMI / DSI interfaces for connecting displays. 6. Onboard USB TO UART, for serial debugging. 7. Cooling fan interface, autorun on power-up OR controlled by IO pins. 8. Adopt isolated SMPS (Switching mode power supply).Specifications1. Power supply: Micro USB port / PoE Ethernet port 2. PoE power input: 37V ~ 57V DC in 3. PoE power output: 5V 2.5A DC out 4. Operating Temperature: -25 degree C ~ 80 degree C 5. Network standard: 802.3af PoE standard 6. Dimensions: 144mm x 88mm 7. Mounting hole size: 3.2mmSpecification: Package Weight One Package Weight 0.48kgs / 1.05lb One Package Size 16cm * 12cm * 5cm / 6.3inch * 4.72inch * 1.97inch Qty per Carton 40 Carton Weight 19.50kgs / 42.99lb Carton Size 50cm * 32cm * 27cm / 19.69inch * 12.6inch * 10.63inch Loading Container 20GP: 617 cartons * 40 pcs = 24680 pcs 40HQ: 1432 cartons * 40 pcs = 57280 pcs

Read more less

FeaturesThe Compute Module PoE Board is a development board that you can plug a Raspberry Pi Compute Module into, and make use of the resources of Pi more flexibly. With the PoE (Power over Ethernet) feature, and versatile onboard peripheral interfaces, it is suitable for evaluating the Raspberry Pi compute module, also is an ideal choice for end products. 1. Raspberry Pi GPIO header, for connecting sorts of Raspberry Pi HATs. 2. 10/100M auto-negotiation Ethernet port, with PoE enabled. 3. 4 x USB ports, which allows connecting more USB devices. 4. 2 x CSI camera interfaces. 5. Onboard HDMI / DSI interfaces for connecting displays. 6. Onboard USB TO UART, for serial debugging. 7. Cooling fan interface, autorun on power-up OR controlled by IO pins. 8. Adopt isolated SMPS (Switching mode power supply).Specifications1. Power supply: Micro USB port / PoE Ethernet port 2. PoE power input: 37V ~ 57V DC in 3. PoE power output: 5V 2.5A DC out 4. Operating Temperature: -25 degree C ~ 80 degree C 5. Network standard: 802.3af PoE standard 6. Dimensions: 144mm x 88mm 7. Mounting hole size: 3.2mmSpecification: Package Weight One Package Weight 0.48kgs / 1.05lb One Package Size 16cm * 12cm * 5cm / 6.3inch * 4.72inch * 1.97inch Qty per Carton 40 Carton Weight 19.50kgs / 42.99lb Carton Size 50cm * 32cm * 27cm / 19.69inch * 12.6inch * 10.63inch Loading Container 20GP: 617 cartons * 40 pcs = 24680 pcs 40HQ: 1432 cartons * 40 pcs = 57280 pcs

Read more less

Specifications1. CM4 Socket: Available on all variants of Compute Module 4 2. Network: Gigabit Ethernet RJ45 connector, 100M Ethernet RJ45 connector 3. USB: USB 2.0 Type A x 2 4. Connector: Isolated RS485 x 4, power screw terminal x 1 5. Camera: MIPI CSI-2 port x 2 (15pin 1.0mm FPC connector) 6. Video: HD-MI interface x 1, support 4K 30fps output 7. RTC: Real Time Clock with Battery Socket and Ability to Wake Compute Module 4 8. Storage: MicroSD card slot for Compute Module 4 Lite (no eMMC) variant 9. Fan head: allow speed adjustment, 5V 10. Indicator: Power indicator x 1, CM4 status indicator x 1, User LED x 2, RS485 communication indicator x 8 11. Power input: 7-36V 12. Dimensions: 123 x 98 x 32mmPackage List1. CM4-ETH-RS485-BASE-B x 1 2. Metal case (top and bottom) x 1 3. Fan x 1 4. 12V 2A Power Supply x 1 5. Screwdriver x 1 6. Antenna connector rubber plug x 1 7. Screws pack x 1Specification: Package Weight One Package Weight 0.48kgs / 1.05lb One Package Size 16cm * 12cm * 5cm / 6.3inch * 4.72inch * 1.97inch Qty per Carton 40 Carton Weight 19.50kgs / 42.99lb Carton Size 50cm * 32cm * 27cm / 19.69inch * 12.6inch * 10.63inch Loading Container 20GP: 617 cartons * 40 pcs = 24680 pcs 40HQ: 1432 cartons * 40 pcs = 57280 pcs

Read more less

Specifications1. CM4 Socket: Available on all variants of Compute Module 4 2. Network: Gigabit Ethernet RJ45 connector, 100M Ethernet RJ45 connector 3. USB: USB 2.0 Type A x 2 4. Connector: Isolated RS485 x 4, power screw terminal x 1 5. Camera: MIPI CSI-2 port x 2 (15pin 1.0mm FPC connector) 6. Video: HD-MI interface x 1, support 4K 30fps output 7. RTC: Real Time Clock with Battery Socket and Ability to Wake Compute Module 4 8. Storage: MicroSD card slot for Compute Module 4 Lite (no eMMC) variant 9. Fan head: allow speed adjustment, 5V 10. Indicator: Power indicator x 1, CM4 status indicator x 1, User LED x 2, RS485 communication indicator x 8 11. Power input: 7-36V 12. Dimensions: 123 x 98 x 32mmPackage List1. CM4-ETH-RS485-BASE-B x 1 2. Metal case (top and bottom) x 1 3. Fan x 1 4. 12V 2A Power Supply x 1 5. Screwdriver x 1 6. Antenna connector rubber plug x 1 7. Screws pack x 1Specification: Package Weight One Package Weight 0.48kgs / 1.05lb One Package Size 16cm * 12cm * 5cm / 6.3inch * 4.72inch * 1.97inch Qty per Carton 40 Carton Weight 19.50kgs / 42.99lb Carton Size 50cm * 32cm * 27cm / 19.69inch * 12.6inch * 10.63inch Loading Container 20GP: 617 cartons * 40 pcs = 24680 pcs 40HQ: 1432 cartons * 40 pcs = 57280 pcs

Read more less

FeaturesThe Compute Module PoE Board is a development board that you can plug a Raspberry Pi Compute Module into, and make use of the resources of Pi more flexibly. With the PoE (Power over Ethernet) feature, and versatile onboard peripheral interfaces, it is suitable for evaluating the Raspberry Pi compute module, also is an ideal choice for end products. 1. Raspberry Pi GPIO header, for connecting sorts of Raspberry Pi HATs. 2. 10/100M auto-negotiation Ethernet port, with PoE enabled. 3. 4 x USB ports, which allows connecting more USB devices. 4. 2 x CSI camera interfaces. 5. Onboard HDMI / DSI interfaces for connecting displays. 6. Onboard USB TO UART, for serial debugging. 7. Cooling fan interface, autorun on power-up OR controlled by IO pins. 8. Adopt isolated SMPS (Switching mode power supply).Specifications1. Power supply: Micro USB port / PoE Ethernet port 2. PoE power input: 37V ~ 57V DC in 3. PoE power output: 5V 2.5A DC out 4. Operating Temperature: -25 degree C ~ 80 degree C 5. Network standard: 802.3af PoE standard 6. Dimensions: 144mm x 88mm 7. Mounting hole size: 3.2mmSpecification: Package Weight One Package Weight 0.48kgs / 1.05lb One Package Size 16cm * 12cm * 5cm / 6.3inch * 4.72inch * 1.97inch Qty per Carton 40 Carton Weight 19.50kgs / 42.99lb Carton Size 50cm * 32cm * 27cm / 19.69inch * 12.6inch * 10.63inch Loading Container 20GP: 617 cartons * 40 pcs = 24680 pcs 40HQ: 1432 cartons * 40 pcs = 57280 pcs

Read more less

1. Only compatible with Raspberry Pi 4B2. ABS material shell and two transparent acrylic side panels3. A 0.96-inch OLED screen has been installed on the shell, 28 x 64 pixels, and the default I2C address: 0x3C4. M.2 SATA SSD 2280/2260/2240 mass storage adapter board, supports M.2 SATA SSD up to 2TB5. Note: Raspberry Pi 4B is not includedSpecification: Package Weight One Package Weight 3.00kgs / 6.62lb One Package Size 50cm * 40cm * 20cm / 19.69inch * 15.75inch * 7.87inch Qty per Carton 3 Carton Weight 10.00kgs / 22.05lb Carton Size 52cm * 42cm * 62cm / 20.47inch * 16.54inch * 24.41inch Loading Container 20GP: 196 cartons * 3 pcs = 588 pcs 40HQ: 457 cartons * 3 pcs = 1371 pcs

Read more less

1. Size: 5.5 inches2. Port: HDMI3. Display panel: IPS, 2K resolution4. Touch port: USB5. Support Raspberry Pi operating system, 10-point touch.6. Support Ubuntu / Kali, single touch.7. Only Raspberry Pi 4B and CM4 have enough CPU performance to fully drive this 2K monitor8. When using Raspberry Pi 3B+/Pi 3B/Zero 2w/Zero w, only the default portrait display is supported and cannot be rotated.9. This chassis only supports Raspberry Pi 4BSpecification: Package Weight One Package Weight 0.28kgs / 0.63lb One Package Size 15cm * 8cm * 4cm / 5.91inch * 3.15inch * 1.57inch Qty per Carton 84 Carton Weight 26.20kgs / 57.76lb Carton Size 47cm * 34cm * 30cm / 18.5inch * 13.39inch * 11.81inch Loading Container 20GP: 556 cartons * 84 pcs = 46704 pcs 40HQ: 1291 cartons * 84 pcs = 108444 pcs

Read more less

1. 5G standard: 3GPP R162. Chip: Qualcomm Snapdragon X623. Operating system: for Windows/Linux/Android4. Dialing: RNDIS, NDIS, PPP, MBIM5. SIM card: 1.8V/2.95V6. Power supply: 3.135-4.4V7. Standard M.2 interface8. High throughput data communication9. The AT command of SIM8262E-M2 is compatible with SIM7912G/SIM8200X-M2 series modulesSpecification: Package Weight One Package Weight 0.08kgs / 0.19lb One Package Size 6cm * 3cm * 3cm / 2.36inch * 1.18inch * 1.18inch Qty per Carton 400 Carton Weight 33.00kgs / 72.75lb Carton Size 32cm * 26cm * 32cm / 12.6inch * 10.24inch * 12.6inch Loading Container 20GP: 1001 cartons * 400 pcs = 400400 pcs 40HQ: 2325 cartons * 400 pcs = 930000 pcs

Read more less

1. Working voltage: 3.3V/5V2. Interface: 3-wire SPI, 4-wire SPI3. Gray scale: 24. Full refresh time: 3215. Refresh power: about 57mW6. Dot pitch: 0.176 × 0.176mm7. Standby current: about 0.01uA8. Resolution: 296×168 pixels9. Without backlight, the last content can be displayed for a long time even if the power is cut off.10. Ultra-low power consumption, basically only need to refresh.11. SPI interface for connecting Raspberry Pi / Jetson Nano / Arduino / STM32 and other controller boards.12. Onboard voltage converter, compatible with 3.3V/5V MC.Specification: Package Weight One Package Weight 0.06kgs / 0.14lb One Package Size 8cm * 4cm * 3cm / 3.15inch * 1.57inch * 1.18inch Qty per Carton 400 Carton Weight 25.00kgs / 55.12lb Carton Size 42cm * 34cm * 32cm / 16.54inch * 13.39inch * 12.6inch Loading Container 20GP: 583 cartons * 400 pcs = 233200 pcs 40HQ: 1354 cartons * 400 pcs = 541600 pcs

Read more less

1. Input interface: HDMI x 32. Support 4K/2K 30Hz3. Built-in input equalizer, can automatically adjust the input signal4. Output interface: HD x15. Built-in output drive regulator, which can automatically adjust the output signal amplitude6. Support HDMI 1.4b and DVI1.0 standard7. Transmission speed: up to 3GbpsSpecification: Package Weight One Package Weight 0.10kgs / 0.23lb One Package Size 10cm * 6cm * 3cm / 3.94inch * 2.36inch * 1.18inch Qty per Carton 200 Carton Weight 21.00kgs / 46.30lb Carton Size 42cm * 32cm * 32cm / 16.54inch * 12.6inch * 12.6inch Loading Container 20GP: 620 cartons * 200 pcs = 124000 pcs 40HQ: 1439 cartons * 200 pcs = 287800 pcs

Read more less

1. Power supply: 9-24V2. Communication interface: RS485 port x 1, Ethernet port x 13. Baud rate: 300-115200 bps4. Data bits: 5-9 bits5. Configuration: host, web browser, device management function library6. Communication method: TCP/IP direct communication, VCOM7. Working temperature: -40 degrees to 85 degrees8. Main function: Bidirectional transparent data transmission between RS485 and Ethernet9. It is easy to combine multi-rail installed serial servers together, more freedom.10. It is suitable for Modbus grid upgrade and can be used in conjunction with 3D configuration software.11. Support TCP server / TCP client / UDP mode / UDP multicast.12. Multi-host rolling polling support, easy for cloud communication and device identification.Specification: Package Weight One Package Weight 0.14kgs / 0.30lb One Package Size 12cm * 8cm * 6cm / 4.72inch * 3.15inch * 2.36inch Qty per Carton 100 Carton Weight 16.00kgs / 35.27lb Carton Size 50cm * 42cm * 32cm / 19.69inch * 16.54inch * 12.6inch Loading Container 20GP: 396 cartons * 100 pcs = 39600 pcs 40HQ: 921 cartons * 100 pcs = 92100 pcs

Read more less

1. CM4 socket: For all variants of Compute Module 42. Networking: Gigabit Ethernet RJ45 connector3. Connector: M.2 M KEY, support communication module or NVME SSD4. USB: USB 2.0 Type A × Type 25. Display: LCD port6. Camera: MIPI CSI-2 camera port × 27. Video: HDMI port, support 4K 30fps output8. Fan header: allow speed adjustment, 5V9. Power input: 5VSpecification: Package Weight One Package Weight 0.10kgs / 0.23lb One Package Size 10cm * 6cm * 3cm / 3.94inch * 2.36inch * 1.18inch Qty per Carton 200 Carton Weight 21.00kgs / 46.30lb Carton Size 42cm * 32cm * 32cm / 16.54inch * 12.6inch * 12.6inch Loading Container 20GP: 620 cartons * 200 pcs = 124000 pcs 40HQ: 1439 cartons * 200 pcs = 287800 pcs

Read more less

1. Based on Qualcomm platform, support 5G NSA and SA networking, support multi-mode & multi-band2. Multi-constellation dual-band positioning: GPS, Beidou, Glonass, Galileo, and QZSS3. Operating system support: Windows/Linux/Android4. USB 3.1 port (USB 2.0 compatible) for connecting to PC, Raspberry Pi, or Jetson Nano host board to enable high speed 5G communication5. Standard M.2 B KEY slot, compatible with different 5G modules: SIM8202X-M2 / SIM8200EA-M2 / SIM8262X-M2 series6. Onboard UART, PWR, and RST control pin, built-in voltage level translator, enabled via DIP switch, for use with hosts like Raspberry Pi or Arduino7. Onboard USB-C connector, enabled via switch, for connecting standalone power supply for the module, allows more loads, stable amd flexible power supply8. Onboard power supply on/off switch, reset button and LED indicator, easy to turn on/off the module or monitor the operating status9. 4x SMA to IPEX antenna connectors, with pre-soldered SMA terminals for connecting antennas10. 2x SIM card slot, dual card single standby, switchable via AT command11. Onboard audio jack and audio decoder, allows audio operation like making phone call12. High efficiency power supply circuit, up to 3A output currentSpecification: Package Weight One Package Weight 0.30kgs / 0.67lb One Package Size 15cm * 10cm * 6cm / 5.91inch * 3.94inch * 2.36inch Qty per Carton 84 Carton Weight 26.20kgs / 57.76lb Carton Size 47cm * 42cm * 44cm / 18.5inch * 16.54inch * 17.32inch Loading Container 20GP: 307 cartons * 84 pcs = 25788 pcs 40HQ: 712 cartons * 84 pcs = 59808 pcs

Read more less

1. POE power input: 37-57V2. Power output: 5V/2.5A3. Network standard: IEEE 802.3af PoE4. Size: 65x32mm5. Support Raspberry Pi 3B+/4B, compatible with Raspberry Pi official case.6. PoE (Power over Ethernet) function, in line with IEEE 802.3af standard.7. Fully isolated switch mode power supply (SMPS)8. Smaller, more flexible, and more compact component layout.Specification: Package Weight One Package Weight 0.08kgs / 0.19lb One Package Size 8cm * 5cm * 3cm / 3.15inch * 1.97inch * 1.18inch Qty per Carton 240 Carton Weight 20.20kgs / 44.53lb Carton Size 34cm * 32cm * 32cm / 13.39inch * 12.6inch * 12.6inch Loading Container 20GP: 765 cartons * 240 pcs = 183600 pcs 40HQ: 1778 cartons * 240 pcs = 426720 pcs

Read more less

1. Only compatible with Raspberry Pi 4B2. ABS material shell and two transparent acrylic side panels3. Using the RGB programmable LED on the screen driver board, you can adjust the color of the light according to your preference4. Super heat dissipation, using 5mm copper tubes, 28 aluminum cooling fins and a 40mm cooling fan. The RGB LED on the fan will change with the LED on the driver board5. It adopts a 0.96-inch OLED screen display, which is easy to assemble or disassemble, and can display system information such as the IP address of the Raspberry Pi, CPU temperature, memory status, and network card traffic through programming.Specification: Package Weight One Package Weight 2.00kgs / 4.42lb One Package Size 50cm * 40cm * 20cm / 19.69inch * 15.75inch * 7.87inch Qty per Carton 3 Carton Weight 7.00kgs / 15.43lb Carton Size 52cm * 42cm * 62cm / 20.47inch * 16.54inch * 24.41inch Loading Container 20GP: 196 cartons * 3 pcs = 588 pcs 40HQ: 457 cartons * 3 pcs = 1371 pcs

Read more less

Overview1. This is a Raspberry Pi LoRa HAT based on SX1268, covers 470MHz frequency band. It allows data transmission up to 5km through serial port.2. By utilizing the new generation LoRa spread spectrum modulation technology, the communication distance of the module is as long as 5km, also supports auto repeating to transmit longer. Other features include Wake on Radio, wireless config, carrier sensing, communication key, and so on.3. Comparing with normal LoRa modules, the SX1268 LoRa HAT achieves longer communication distance, higher rate, lower consumption, better safety and anti-interference. It is suitable for various applications such as industrial control, smart home, data collection, etc.Features1. Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards2. Onboard CP2102 USB TO UART converter, for serial debugging3. Brings the UART control interface, for connecting host boards like Arduino/STM324. 4x LED indicators, easy to check the module status5. LoRa spread spectrum modulation technology, up to 84 available signal channel, longer communication distance, more robust to interference6. Auto multi-level repeating, suit for ultra long range communication, allows multi network on the same region7. Low power consumption features like deep sleeping and Wake on Radio, ideal for battery-powered applications8. Customizable communication key which wont be retrieved, greatly improves the security of user data9. Support LBT, monitoring the signal channel noise before transmitting, greatly improves the success ratio under extreme environment10. Support RSSI signal intensity indicating, for evaluating signal quality, tuning the network11. Support wireless parameter configuration, by sending wireless command/data packet, remotely configure or retrieve the module parameter12. Support fixed-point transmission, broadcast, signal channel monitor13. Come with development resources and manual (examples for Raspberry Pi/STM32)What is on Board1. SX1268 LoRa module2. 74HC125V: voltage level translator3. CP2102: USB TO UART converter4. Raspberry Pi GPIO connector: for connecting with Raspberry Pi5. USB TO UART port6. UART header: for connecting host boards like STM32/Arduino7. SMA antenna connector8. IPEX antenna connector9. Indicators:- RXD/TXD: UART RX/TX indicator- AUX: auxiliary indicator- PWR: power indicator10. UART selection jumpers- A: Control the LoRa module through USB TO UART- B: Control the LoRa module through Raspberry Pi- C: Access Raspberry Pi through USB TO UART11. LoRa mode selection jumpers- Short M0, short M1: Transmission mode- Short M0, open M1: Configuration mode- Open M0, short M1: WOR mode- Open M0, open M1: deep sleep modeSpecification1. RF module: SX12682. Frequency band: 410.125 ~ 493.125MHz3. Radio rate: 0.3kbps ~ 62.5kbps (programmable)4. Transmit power: 22.0dBm (10/13/17/22dBm programmable)5. Receive sensitivity: -147dBm (radio rate 2.4kbps)6. Power consumption: - Transmit current: 110mA (transient consumption)- Receive current: 11mA- Sleep current: 2uA (LoRa module software shutoff)7. Communication interface: UART (TTL level)8. Baudrate: 1200bps ~ 115200bps (9600bps by default)9. Packet length: 240 Byte (32/64/128/240 Byte programmable)10. Cache: 1000 Byte11. Experimental range: 5km (condition: cloudless and wild, altitude 2.5m, antenna gain 5dBi, radio rate 2.4kbps)12. Power supply: 5V13. Logic level: 3.3V/5V14. Operating temperature: -40~85 degree C15. Applications: Smart home, industrial sensors, building automation, smart meters, and more other IoT applications16. Dimensions: 7cm x 12cm x 2cm17. Weight: 69g18. Packing List:- SX1268 470M LoRa HAT x1- USB type A plug to micro plug cable x1- 470MHz antenna x1Specification: Package Weight One Package Weight 0.09kgs / 0.19lb One Package Size 15cm * 8cm * 2cm / 5.91inch * 3.15inch * 0.79inch Qty per Carton 400 Carton Weight 15.00kgs / 33.07lb Carton Size 60cm * 40cm * 40cm / 23.62inch * 15.75inch * 15.75inch Loading Container 20GP: 277 cartons * 400 pcs = 110800 pcs 40HQ: 644 cartons * 400 pcs = 257600 pcs

Read more less

Overview1. This is a Pi LoRa HAT based on SX1262, covers 915MHz frequency band. It allows data transmission up to 5km through serial port.2. By utilizing the new generation LoRa spread spectrum modulation technology, the communication distance of the module is as long as 5km, also supports auto repeating to transmit longer. Other features include Wake on Radio, wireless config, carrier sensing, communication key, and so on.3. Comparing with normal LoRa modules, the SX1262 LoRa HAT achieves longer communication distance, higher rate, lower consumption, better safety and anti-interference. It is suitable for various applications such as industrial control, smart home, data collection, etc.Features1.Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards2. Onboard CP2102 USB TO UART converter, for serial debugging3. Bring the UART control interface, for connecting host boards like Arduino/STM324. 4x LED indicators, easy to check the module status5. LoRa spread spectrum modulation technology, up to 81 available signal channel, longer communication distance, more robust to interference6. Auto multi-level repeating, suit for ultra long range communication, allows multi network on the same region7. Low power consumption features like deep sleeping and Wake on Radio, ideal for battery-powered applications8. Customizable communication key which wont be retrieved, greatly improves the security of user data9. Support LBT, monitoring the signal channel noise before transmitting, greatly improves the success ratio under extreme environment10. Support RSSI signal intensity indicating, for evaluating signal quality, tuning the network11. Support wireless parameter configuration, by sending wireless command/data packet, remotely configure or retrieve the module parameter12. Support fixed-point transmission, broadcast, signal channel monitor13. Come with development resources and manual (examples for Raspberry Pi/STM32)What is on Board1. SX1262 LoRa module2. 74HC125V: voltage level translator3. CP2102: USB TO UART converter4. Raspberry Pi GPIO connector: for connecting with Raspberry Pi5. USB TO UART port6. UART header: for connecting host boards like STM32/Arduino7. SMA antenna connector8. IPEX antenna connector9. Indicators:- RXD/TXD: UART RX/TX indicator- AUX: auxiliary indicator- PWR: power indicator10. UART selection jumpers- A: Control the LoRa module through USB TO UART- B: Control the LoRa module through Raspberry Pi- C: Access Raspberry Pi through USB TO UART11. LoRa mode selection jumpers- Short M0, short M1: Transmission mode- Short M0, open M1: Configuration mode- Open M0, short M1: WOR mode- Open M0, open M1: deep sleep modeSpecification1. RF module: SX12622. Frequency band: 850.125 ~ 930.125MHz3. Radio rate: 0.3kbps ~ 62.5kbps (programmable)4. Transmit power: 22.0dBm (10/13/17/22dBm programmable)5. Receive sensitivity: -147dBm (radio rate 2.4kbps)6. Power consumption: - Transmit current: 133mA (transient consumption)- Receive current: 11mA- Sleep current: 2uA (LoRa module software shutoff)7. Communication interface: UART (TTL level)8. Baudrate: 1200bps ~ 115200bps (9600bps by default)9. Packet length: 240 Byte (32/64/128/240 Byte programmable)10. Cache: 1000 Byte11. Experimental range: 5km (condition: cloudless and wild, altitude 2.5m, antenna gain 5dBi, radio rate 2.4kbps)12. Power supply: 5V13. Logic level: 3.3V/5V14. Operating temperature: -40~85 degree C15. Applications: Smart home, industrial sensors, building automation, smart meters, and more other IoT applications16. Dimensions: 7cm x 12cm x 2cm17. Weight: 69g18. Packing List:- SX1262 915MHz LoRa HAT x1- USB type A plug to micro plug cable x1- 915MHz antenna x1Specification: Package Weight One Package Weight 0.10kgs / 0.22lb One Package Size 15cm * 8cm * 2cm / 5.91inch * 3.15inch * 0.79inch Qty per Carton 400 Carton Weight 44.80kgs / 98.77lb Carton Size 60cm * 40cm * 40cm / 23.62inch * 15.75inch * 15.75inch Loading Container 20GP: 277 cartons * 400 pcs = 110800 pcs 40HQ: 644 cartons * 400 pcs = 257600 pcs

Read more less

Overview1. This is a Raspberry Pi LoRa HAT based on SX1268, covers 433MHz frequency band. It allows data transmission up to 5km through serial port.2. By utilizing the new generation LoRa spread spectrum modulation technology, the communication distance of the module is as long as 5km, also supports auto repeating to transmit longer. Other features include Wake on Radio, wireless config, carrier sensing, communication key, and so on.3. Comparing with normal LoRa modules, the SX1268 LoRa HAT achieves longer communication distance, higher rate, lower consumption, better safety and anti-interference. It is suitable for various applications such as industrial control, smart home, data collection, etc.Features1.Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards2. Onboard CP2102 USB TO UART converter, for serial debugging3. Bring the UART control interface, for connecting host boards like Arduino/STM324. 4x LED indicators, easy to check the module status5. LoRa spread spectrum modulation technology, up to 84 available signal channel, longer communication distance, more robust to interference6. Auto multi-level repeating, suit for ultra long range communication, allows multi network on the same region7. Low power consumption features like deep sleeping and Wake on Radio, ideal for battery-powered applications8. Customizable communication key which wont be retrieved, greatly improves the security of user data9. Support LBT, monitoring the signal channel noise before transmitting, greatly improves the success ratio under extreme environment10. Support RSSI signal intensity indicating, for evaluating signal quality, tuning the network11. Support wireless parameter configuration, by sending wireless command/data packet, remotely configure or retrieve the module parameter12. Support fixed-point transmission, broadcast, signal channel monitor13. Come with development resources and manual (examples for Raspberry Pi/STM32)What is on Board1. SX1268 LoRa module2. 74HC125V: voltage level translator3. CP2102: USB TO UART converter4. Raspberry Pi GPIO connector: for connecting with Raspberry Pi5. USB TO UART port6. UART header: for connecting host boards like STM32/Arduino7. SMA antenna connector8. IPEX antenna connector9. Indicators:- RXD/TXD: UART RX/TX indicator- AUX: auxiliary indicator- PWR: power indicator10. UART selection jumpers- A: Control the LoRa module through USB TO UART- B: Control the LoRa module through Raspberry Pi- C: Access Raspberry Pi through USB TO UART11. LoRa mode selection jumpers- Short M0, short M1: Transmission mode- Short M0, open M1: Configuration mode- Open M0, short M1: WOR mode- Open M0, open M1: deep sleep modeSpecification1. RF module: SX12682. Frequency band: 410.125 ~ 493.125MHz3. Radio rate: 0.3kbps ~ 62.5kbps (programmable)4. Transmit power: 22.0dBm (10/13/17/22dBm programmable)5. Receive sensitivity: -147dBm (radio rate 2.4kbps)6. Power consumption: - Transmit current: 110mA (transient consumption)- Receive current: 11mA- Sleep current: 2uA (LoRa module software shutoff)7. Communication interface: UART (TTL level)8. Baudrate: 1200bps ~ 115200bps (9600bps by default)9. Packet length: 240 Byte (32/64/128/240 Byte programmable)10. Cache: 1000 Byte11. Experimental range: 5km (condition: cloudless and wild, altitude 2.5m, antenna gain 5dBi, radio rate 2.4kbps)12. Power supply: 5V13. Logic level: 3.3V/5V14. Operating temperature: -40~85 degree C15. Applications: Smart home, industrial sensors, building automation, smart meters, and more other IoT applications16. Dimensions: 7cm x 12cm x 2cm17. Weight: 69g18. Packing List:- SX1268 433MHz LoRa HAT x1- USB type A plug to micro plug cable x1- 433MHz antenna x1Specification: Package Weight One Package Weight 0.09kgs / 0.19lb One Package Size 15cm * 8cm * 2cm / 5.91inch * 3.15inch * 0.79inch Qty per Carton 400 Carton Weight 15.00kgs / 33.07lb Carton Size 60cm * 40cm * 40cm / 23.62inch * 15.75inch * 15.75inch Loading Container 20GP: 277 cartons * 400 pcs = 110800 pcs 40HQ: 644 cartons * 400 pcs = 257600 pcs

Read more less