Waveshare XCore407I, STM32F4 Core Board

Description

Overview
1. XCore407I is an STM32 MCU core board that features the STM32F407IGT6 on board.
2. Clock circuit, USB power management
3. Onboard devices: USB HS PHY, Ethernet PHY, 1G Bit NandFlash
4. Connectors:USB HS (mini / type A), USB FS (mini), Ethernet (RJ45)
5. All the idle I/O ports are accessible on the pin headers
6. 2.0mm pin header pitch, smaller size, easier to integrate into user system
7. Note : please consider the EVK407I, which supports easily programing/debugging.

What is On Board
STM32F407IGT6 development board on board resource

1. STM32F407IGT6: The high performance STM32 MCU which features:
- Core: Cortex-M4 32-bit RISC
- Feature: a full set of single-cycle DSP instructions
- Operating Frequency: 168MHz, 210 DMIPS/1.25 DMIPS/MHz
- Operating Voltage: 1.8V-3.6V
- Package: LQFP176
- Memories: 1024kB Flash, 192+4kB SRAM
- MCU communication Interfaces:
-- 3 x SPI, 4 x USART, 2 x UART, 2 x I2S, 3 x I2C
-- 1 x FSMC, 1 x SDIO, 2 x CAN
-- 1 x USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, ULPI and on-chip full-speed PHY
-- 1 x 10/100 Ethernet MAC
-- 1 x 8 to 14-bit parallel camera interface
- AD & DA converters: 3 x AD (12-bit, 1μs, shares 24 channels); 2 x DA (12-bit)
- Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP
2. MIC2075-2, onboard USB FS power management device
3. AMS1117-3.3, 3.3V voltage regulator
4. K9F1G08U0E, 1G Bit NandFlash
5. DP83848, Ethernet PHY
6. MIC2075-1, onboard USB HS power management device
7. USB3300, USB HS PHY
8. Power supply switch, powered from 5Vin or USB connection
9. Boot mode switch, for configuring BOOT0 pin
10. Power indicator
11. USB FS LED
12. USB HS LED
13. Reset button
14. 8M crystal, MCU clock, enables the MCU run at higher speed by frequency multiplication
15. 24M crystal, USB3300 clock
16. 50M crystal, DP83848 clock
17. 32.768K crystal, for internal RTC with calibration
18. Ethernet connector
19. USB FS mini connector
20. USB HS mini connector
21. USB HS type A connector
22. MCU pins expander, VCC, GND and all the idle I/O ports are accessible on expansion connectors for further expansion
23. USB OTG/HOST jumper
24. VREF/VBAT jumper
25. Ethernet I/O selection solder joint
26. USB HS I/O selection solder joint
27. PDR selection solder joint: 1.8-3.6V, -40~105℃ OR 1.7-3.6V, 0~70℃

Package Contents
1. XCore407I development board x 1
2. USB type A to Mini-B cable x 1
3. Software CD x 1

Waveshare XCore407I, STM32F4 Core Board

Product form

SKU: ZY13988205

  • In stock (Processing Time 1 - 72 hours)

€90,83

    • Guaranteed secure & safe checkout.

    Icon for truckShipping Methods

    To find out all available shipping methods, and the exact delivery time add the product to the cart and verify it using our shipping calculator.

    Icon for 24_hour_clockOrder Processing Time

    All orders are shipped within a maximum of 72 hours from the order's arrival.

    Icon for coinMoney Back Guarantee

    Garmade Money Back Guarantee- Get the item you ordered or your money back, it's that simple.

    Icon for image_placeholderMismatched Product

    Product doesn't match the description? Contact us within 31 days after you receive it!

    Icon for mobile_paymentRefunds

    In case of cancellation, money will be refunded to your account within 14 days.

    Description

    Overview
    1. XCore407I is an STM32 MCU core board that features the STM32F407IGT6 on board.
    2. Clock circuit, USB power management
    3. Onboard devices: USB HS PHY, Ethernet PHY, 1G Bit NandFlash
    4. Connectors:USB HS (mini / type A), USB FS (mini), Ethernet (RJ45)
    5. All the idle I/O ports are accessible on the pin headers
    6. 2.0mm pin header pitch, smaller size, easier to integrate into user system
    7. Note : please consider the EVK407I, which supports easily programing/debugging.

    What is On Board
    STM32F407IGT6 development board on board resource

    1. STM32F407IGT6: The high performance STM32 MCU which features:
    - Core: Cortex-M4 32-bit RISC
    - Feature: a full set of single-cycle DSP instructions
    - Operating Frequency: 168MHz, 210 DMIPS/1.25 DMIPS/MHz
    - Operating Voltage: 1.8V-3.6V
    - Package: LQFP176
    - Memories: 1024kB Flash, 192+4kB SRAM
    - MCU communication Interfaces:
    -- 3 x SPI, 4 x USART, 2 x UART, 2 x I2S, 3 x I2C
    -- 1 x FSMC, 1 x SDIO, 2 x CAN
    -- 1 x USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, ULPI and on-chip full-speed PHY
    -- 1 x 10/100 Ethernet MAC
    -- 1 x 8 to 14-bit parallel camera interface
    - AD & DA converters: 3 x AD (12-bit, 1μs, shares 24 channels); 2 x DA (12-bit)
    - Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP
    2. MIC2075-2, onboard USB FS power management device
    3. AMS1117-3.3, 3.3V voltage regulator
    4. K9F1G08U0E, 1G Bit NandFlash
    5. DP83848, Ethernet PHY
    6. MIC2075-1, onboard USB HS power management device
    7. USB3300, USB HS PHY
    8. Power supply switch, powered from 5Vin or USB connection
    9. Boot mode switch, for configuring BOOT0 pin
    10. Power indicator
    11. USB FS LED
    12. USB HS LED
    13. Reset button
    14. 8M crystal, MCU clock, enables the MCU run at higher speed by frequency multiplication
    15. 24M crystal, USB3300 clock
    16. 50M crystal, DP83848 clock
    17. 32.768K crystal, for internal RTC with calibration
    18. Ethernet connector
    19. USB FS mini connector
    20. USB HS mini connector
    21. USB HS type A connector
    22. MCU pins expander, VCC, GND and all the idle I/O ports are accessible on expansion connectors for further expansion
    23. USB OTG/HOST jumper
    24. VREF/VBAT jumper
    25. Ethernet I/O selection solder joint
    26. USB HS I/O selection solder joint
    27. PDR selection solder joint: 1.8-3.6V, -40~105℃ OR 1.7-3.6V, 0~70℃

    Package Contents
    1. XCore407I development board x 1
    2. USB type A to Mini-B cable x 1
    3. Software CD x 1

    Additional Information

    Icon for truckShipping Info

    IMPORTANT INFO - PLEASE CHECK BEFORE ORDERING.



      Estimated transit time and postage fee depends on the method you choose at checkout. Please add the desired product to the cart and there you will be able to see all this information.

      Complete and right address is the guarantee of fast and efficient delivery, so please kindly recheck it when you place an order.

      In order to ensure a fast and efficient delivery, we need to have the method of contact with you. Email and Phone Number is a very important detail and must be accurate. All orders with an incorrect email or phone number will be canceled immediately.

      We strive to dispatch all orders within 72 hours of placing your order. But sometimes if the order is big or the products are more sophisticated, it can take a little longer. As soon as we dispatched it, you will receive a confirmation email along with a tracking number.

      Please be aware that sometimes due to unclear address, hard to access, no answer at address, the package can be kept at your local post office for collection. In this case you will be informed by the delivery company and by us. Please also monitor the tracking number.

      For European Union Countries:
    - If your order is less than 150€ excluding shipping costs, then the Taxes are already included in the price. This means that there will be NO extra charge upon delivery.
    - If your order is more than 150€, you will NOT be charged Taxes at the checkout, and you will have to pay upon delivery based on your local VAT rate.

     

    Icon for reviewReviews

    Login

    Forgot your password?

    Don't have an account yet?
    Create account