Products

Overview1. Sensitive for alcohol, ethanol2. Output voltage boosts along with the concentration of the measured gases increases3. Fast response and recovery4. Adjustable sensitivity5. Signal output indicatorSpecifications1. Power: 2.5V ~ 5.0V2. Dimension: 40.0mm * 21.0mm3. Mounting holes size: 2.0mmApplications1. Car alcohol alarm2. BreathalyserHow to UseIn the case of working with a MCU:1. VCC: 2.5V ~ 5.0V2. GND: Power supply ground3. AOUT: MCU.IO (analog output)4. DOUT: MCU.IO (digital output)Package Contents1. MQ-3 Gas Sensor x12. 4-pin custom connector jumper wire x1

Read more less

Overview1. Sensitive for LPG, natural gas, coal gas2. Output voltage boosts along with the concentration of the measured gases increases3. Fast response and recovery4. Adjustable sensitivity5. Signal output indicatorSpecifications1. Power: 2.5V ~ 5.0V2. Dimension: 40.0mm * 21.0mm3. Mounting holes size: 2.0mmApplicationsGas leakage detectorHow to UseIn the case of working with a MCU:1. VCC: 2.5V ~ 5.0V2. GND: Power supply ground3. AOUT: MCU.IO (analog output)4. DOUT: MCU.IO (digital output)Package Contents1. MQ-5 Gas Sensor x12. 4-pin custom connector jumper wire x1

Read more less

Overview1. Sensitive for carbon monoxide2. Output voltage boosts along with the concentration of the measured gases increases3. Fast response and recovery4. Adjustable sensitivity5. Signal output indicatorSpecifications1. Power: 2.5V ~ 5.0V2. Dimension: 40.0mm * 21.0mm3. Mounting holes size: 2.0mmApplicationsCarbon monoxide monitorHow to UseIn the case of working with a MCU:1. VCC: 2.5V ~ 5.0V2. GND: Power supply ground3. AOUT: MCU.IO (analog output)4. DOUT: MCU.IO (digital output)Package Contents1. MQ-7 Gas Sensor x12. 4-pin custom connector jumper wire x1

Read more less

FeaturesThe A7670E Cat-1 HAT is an LTE Cat-1 module, which supports wireless communication modes including LTE-TDD, LTE-FDD, GSM, GPRS and EDGE, with up to 10Mbps downlink rate and 5Mbps uplink rate. It supports Windows/Linux operating systems and multiple network protocols. The module size is the same as SIM7000/SIM7070 series, and the AT commands is mostly compatible with SIM7600 series. It is suitable for IoT applications like remote information processing, monitoring devices, POS, industrial routers, remote diagnosis, and so on. 1. Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards 2. Support protocols including TCP/IP, HTTP(s), MQTT(s), FTP(s), and SSL 3. Support dial-up, telephone call, SMS 4. Support LBS base station positioning, it is able to get the approximate position info via mobile network 5. TTS (Text To Speech) feature, texts in Chinese/English can be converted into spoken words 6. Onboard USB interface, for testing AT Commands, network communication, and so on 7. Onboard audio jack for sound recording, making telephone call, listening the TTS resulting speech, etc. 8. Breakout common used control pins of the A7670X module, make it easy to connect with hosts boards like Arduino/STM32 9. SIM card slot, supports 1.8V/3V SIM card 10. 2x LED indicators, easy to monitor the operating status 11. Onboard voltage translator, operating voltage can be configured to 3.3V or 5V via jumper 12. Come with development resources and manual (examples for Raspberry Pi/Arduino/STM32)SpecificationFrequency band 1. LTE Cat-1: LTE-FDD: B1, B3, B5, B7, B8, B20 2. 2G: GSM/GPRS/EDGE: 900/1800 MHz SMS and audio 1. SMS: Supported types: MT, MO, CB, Text, PDU 2. Storage: USIM card (CB could not be stored on SIM card) 3. Audio feature: Standard 3.5mm audio jack for audio input/output Others 1. Power supply: 5V 2. Operating voltage:5V / 3.3V (configured via jumper) 3. Operating temperature: -30 degree C ~ 80degree C 4. Storage temperature: -45 degree C ~ 90 degree C 5. Dimensions: 65 x 30.5mmPackage List1. A7670E Cat-1 HAT x 1 2. LTE Antenna x 1 3. USB-A to USB-C cable x 1 4. RPi screws pack x 1

Read more less

Features1. Onboard unibody power supply isolation, provides stable isolated voltage, needs no extra power supply for the isolated terminal 2. Onboard photocoupler isolation, prevent interference from external high-voltage circuit connected to the relay 3. High quality relay, contact rating: 10A 250V AC or Less than or equal 10A 30V DC 4. ABS protection enclosure with rail-mount support, easy to install, safe to use 5. Breakout USB port and BOOT pin, make it easy to debug without disassembling the enclosure 6. PWR indicator, RGB LED, and passive buzzer outside the enclosure 7. Come with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples)Specification1. Operation voltage: 5V 2. Relay channel: 8CH 3. Communication protocol: USB 4. Contact form: 1NO 1NC 5. Communication interface: Micro USBPackage List1. ABS protection enclosure (top and bottom) x 1 2. Pico-Relay-B x 1 3. Screwdriver x 1 4. Screws pack x 1

Read more less

1. Base board for Compute Module 4 Lite / eMMC 2. Standard CM4 socket, with multiple peripheral interfaces, suitable for narrow application environment Specifications: 1. CM4 socket: Suitable for all variants of Compute Module 4 2. Connector: Raspberry Pi 40PIN GPIO interface x 1 3. USB: USB 2.0 Type A interface x 1 4. Camera: MIPI CSI-2 port x 1 (15pin 1.0mm FPC connector) 5. Storage: Micro SD card socket for Compute Module 4 Lite (without eMMC) variants 6. Power: 5V 7. Size: 55 x 40mm Package list 1. CM4-NANO-A x1 2. 2 x 20PIN color-coded straight pinheader x 2

Read more less

1. Suitable for evaluating the Raspberry Pi CM4 Or being integrated into end products 2. Standard CM4 socket, 40PIN GPIO, gigabit ethernet, USB2.0, DSI, CSI, 3.5mm Audio Jack... 3. All in the compact body just as the size of CM4 Specifications: 1. CM4 socket: Suitable for all variants of Compute Module 4 2. Networking: Gigabit Ethernet RJ45 connector 3. Connector: Raspberry Pi 40PIN GPIO header x 1 4. USB: USB 2.0 Type A connector x 1 5. Display: MIPI DSI port x 1 (15pin 1.0mm FPC connector) 6. Camera: MIPI CSI-2 port x 1 (15pin 1.0mm FPC connector) 7. Video: Mini HDMI port x 1, supports 4K 30fps output 8. Audio: 3.5mm jack 9. Storage: Micro SD card socket for Compute Module 4 Lite (without eMMC) variants 10. Power input: 5V 11. Dimension: 56 x 41mm Package list: 1. CM4-NANO-B x 1 3. 2*20PIN color-coded straight pinheader x 1

Read more less

NB-IoT HAT for Raspberry Pi, Based on SIM7020E, B1/B3/B5/B8/B20/B28 BandsApplicable Region1. SIM7020E is mainly applicable in Europe, Asia, Africa, Australia.2. Please check the supported bands according to your local service provider when placing order.OverviewThis is an NB-IoT (NarrowBand-Internet of Things) HAT for Raspberry Pi, controlled via serial AT commands, supports communication protocols like LWM2M/COAP/MQTT, etc. Due to the advantages of low delay, low power, low cost, and wide coverage, it is the ideal choice for IoT applications such as intelligent instruments, asset tracking, remote monitoring, and so on.Features1. Raspberry Pi connectivity, compatible with any revision2. Support communication protocols such as LWM2M/COAP/MQTT/TCP/UDP/HTTP/HTTPS, etc.3. Onboard USB interface, for power supply OR debugging4. Breakout UART control pins, to connect with host boards like Arduino/STM325. Onboard voltage translator, 3.3V by default, allows to be switched to 5V via onboard jumper6. SIM card slot, supports NB-IoT specific card7. 2x LED indicators, easy to monitor the working status8. Baudrate: 300bps~921600bps (115200bps by default)9. Control via AT commands (V.25TER, 3GPP TS 27.007, and SIMCOM AT Commands)10. Come with development resources and manual (examples for Raspberry Pi/Arduino/STM32/Python)Communications Specifications1. Band- FDD-LTE B1/B3/B5/B8/B20/B28 2. Data rate- Uplink=<62.5Kbps- Downlink=<26.15Kbps3. SMS- Text mode and PDU mode (depends on the NB card)General Specifications1. Power supply: 5V2. Logic level: 5V/3.3V (3.3V by default)3. Overall current (idle mode): ~18mA4. Single module current (VBAT=3.3V):- Idle mode: 5.6mA- Sleep mode: 0.4mA- PSM mode: 5uA- eDRX mode: 70uA (eDRX=655.36s)5. Dimension: 30.5mm x 65.0mmPackage Contents1. SIM7020E NB-IoT HAT x12. Antenna x13. USB type A plug to micro plug cable x14. RPi screws pack (2pcs) x1Note: The Raspberry Pi is NOT included.

Read more less

Overview1. This is the NodeMCU development board based on ESP32, features WiFi+Bluetooth connectivity, onboard CP2102 and keys. What's more, all the I/O pins of ESP-WROOM-32 module are accessible via the extension headers.2. Thanks to the rich open-source resources, it supports development in various ways such as Lua/AT commands/MicroPython/Arduino/IOT source code, etc. helps you to fast prototype IoT applications.Features1. Onboard ESP-WROOM-32 module2. Onboard CP2102, USB to UART converter3. USB port for power input, firmware programming, or UART debugging4. 2x19pin extension headers, breakout all the I/O pins of the module5. 2x keys, used as reset or user-definedApplicationsThe NodeMCU-32S suit for IOT applications such as:1. Smart home2. Intelligent building3. Industrial automation4. Wearable devices5. IP camera6. Intelligent agricultureSpecifications1. WIFI module: ESP-WROOM-322. Processor: ESP32-D0WDQ63. Built-in Flash: 32Mbit4. Antenna: Onboard PCB antenna5. Peripheral interface: UART/GPIO/ADC/DAC/SDIO/PWM/I2C/I2S6. WiFi protocol: IEEE 802.11 b/g/n7. Bluetooth: Bluetooth 4.28. Frequency range: 2.4G ~ 2.5G (2400M ~ 2483.5M)9. WIFI mode: Station / SoftAP / SoftAP+Station10. Power supply: 5V11. Logic level: 3.3V12. Dimensions: 48.26mm x 25.4mm13. Weight: 10g14. Packing List: NodeMCU-32S x1

Read more less

NUCLEO-L476RG DescriptionThe STM32 Nucleo board provides an affordable and flexible way for users to try out new ideas and build prototypes with any STM32 microcontroller line, choosing from the various combinations of performance, power consumption and features. The Arduino™ connectivity support and ST Morpho headers make it easy to expand the functionality of the STM32 Nucleo open development platform with a wide choice of specialized shields.The STM32 Nucleo board does not require any separate probe as it integrates the ST-LINK/V2-1 debugger and programmer.The STM32 Nucleo board comes with the STM32 comprehensive software HAL library together with various packaged software examples, as well as direct access to mbed online resources.NUCLEO-L476RG Key FeaturesSTM32 microcontroller with LQFP64 packageTwo types of extension resourcesArduino Uno Revision 3 connectivitySTMicroelectronics Morpho extension pin headers for full access to all STM32 I/Osmbed-enabled (http://mbed.org)On-board ST-LINK/V2-1 debugger/programmer with SWD connectorselection-mode switch to use the kit as a standalone ST-LINK/V2-1Flexible board power supplyUSB VBUS or external source(3.3 V, 5 V, 7 - 12 V)Power management access pointThree LEDsUSB communication (LD1), user LED (LD2), power LED (LD3)Two push buttons: USER and RESETUSB re-enumeration capability: three different interfaces supported on USBVirtual Com portMass storageDebug portSupported by wide choice of Integrated Development Environments (IDEs) including IAR™, Keil®, GCC-based IDEs

Read more less

Overview1. Open429I-C is an STM32 development board designed for the STM32F429IGT6 microcontroller, consists of the mother board and the MCU core board Core429I.2. The Open429I-C supports further expansion with various optional accessory boards for specific application. The modular and open design makes it the ideal for starting application development with STM32 series microcontrollers.What has on the mother board1. MCU core board connector: for easily connecting the Core429I2. USART3 interface: easily connects to RS232, RS485, USB TO 232, etc.3. DCMI interface: for connecting camera4. Capacitive touch panel interface: for connecting capacitive touch panel5. CAN2 interface: for connecting CAN modules6. CAN1 interface: for connecting CAN modules7. SDIO interface: for connecting Micro SD module, features much faster access speed rather than SPI8. ULPI interface: for connecting high-speed USB peripheral (the 9. STM32F429I integrates USB HS controller without any PHY device)10. LCD interface 1: for connecting 7inch LCD11. ONE-WIRE interface: easily connects to ONE-WIRE devices (TO-92 package), such as temperature sensor (DS18B20), electronic registration number (DS2401), etc.12. LCD interface 2: for connecting 4.3inch LCD13. I2C2/I2C3 interface: easily connects to I2C peripherals such as I/O expander (PCF8574), EEPROM (AT24Cxx), etc.14. SAI1 interface: for connecting audio modules like UDA1380 module15. Ethernet interface: for connecting Ethernet modules16. USB connector: USB to UART via the onboard convertor PL2303SPI1/SPI2 interfaces:- Easily connects to SPI peripherals such as DataFlash (AT45DBxx), SD card, MP3 module, etc.- Easily connects to AD/DA modules (SPI1 features AD/DA alternative function)17. I2S2/I2S3/I2C1 interface: easily connects to I2S peripherals such as audio module, etc.18. 8-bit FMC interface: easily connects to peripherals such as NandFlash19. 5V DC jack20. 5V/3.3V power input/output: usually used as power output, also common-grounding with other user board21. MCU pins connector: all the MCU I/O ports are accessible on expansion connectors for further expansion22. PL2303: USB to UART convertor23. LEDs: convenient for indicating I/O status and/or program running state24. PL2303 TX-LED / RX-LED25. 12MHz crystal: for PL230326. Joystick: five positions27. WAKE UP button: used as regular button, and/or wake up the STM32 MCU from sleep28. USB to UART jumper29. LED jumper- Short the jumper to connect to default I/Os used in example code- Open the jumper to connect to custom I/Os via jumper wires30. Button/Joystick jumper- Short the jumper to connect to default I/Os used in example code- Open the jumper to connect to custom I/Os via jumper wiresThe "Standard Package" and "Accessory Boards Package" below are included.Standard Package1. Open429I-C development board x 12. USB type A plug to mini-B plug cable x 13. USB type A receptacle to mini-B plug cable x 14. 4-pin 2-pin wires pack x 15. USB power cable x 16. Software CD x 1Accessory Boards Package1. 4.3 inch 480x272 Touch LCD (B) x 12. DP83848 Ethernet Board x 13. USB3300 USB HS Board x 14. NandFlash Board (A) x 15. UDA1380 Board x 16. Micro SD Storage Board x 17. OV2640 Camera Board x 18. Ethernet Cable x 19. 4.3 inch LCD screws pack x 1

Read more less

STM32 development board designed for STM32F429I, features the STM32F429IGT6 MCU, and integrates various standard interfaces, pretty easy for peripheral expansions.Overview1. Open429I-C is an STM32 development board designed for the STM32F429IGT6 microcontroller, consists of the mother board and the MCU core board Core429I.2. The Open429I-C supports further expansion with various optional accessory boards for specific application. The modular and open design makes it the ideal for starting application development with STM32 series microcontrollers.What has on the mother board1. MCU core board connector: for easily connecting the Core429I2. USART3 interface: easily connects to RS232, RS485, USB TO 232, etc.3. DCMI interface: for connecting camera4. Capacitive touch panel interface: for connecting capacitive touch panel5. CAN2 interface: for connecting CAN modules6. CAN1 interface: for connecting CAN modules7. SDIO interface: for connecting Micro SD module, features much faster access speed rather than SPI8. ULPI interface: for connecting high-speed USB peripheral (the STM32F429I integrates USB HS controller without any PHY device)9. LCD interface 1: for connecting 7inch LCD10. ONE-WIRE interface: easily connects to ONE-WIRE devices (TO-92 package), such as temperature sensor (DS18B20), electronic registration number (DS2401), etc.11. LCD interface 2: for connecting 4.3inch LCD12. I2C2/I2C3 interface: easily connects to I2C peripherals such as I/O expander (PCF8574), EEPROM (AT24Cxx), etc.13. SAI1 interface: for connecting audio modules like UDA1380 module14. Ethernet interface: for connecting Ethernet modules15. USB connector: USB to UART via the onboard convertor PL230316. SPI1/SPI2 interfaces:- Easily connects to SPI peripherals such as DataFlash (AT45DBxx), SD card, MP3 module, etc.- Easily connects to AD/DA modules (SPI1 features AD/DA alternative function)17. I2S2/I2S3/I2C1 interface: easily connects to I2S peripherals such as audio module, etc.18. 8-bit FMC interface: easily connects to peripherals such as NandFlash19. 5V DC jack20. 5V/3.3V power input/output: usually used as power output, also common-grounding with other user board21. MCU pins connector: all the MCU I/O ports are accessible on expansion connectors for further expansion22. PL2303: USB to UART convertor23. LEDs: convenient for indicating I/O status and/or program running state24. PL2303 TX-LED / RX-LED25. 12MHz crystal: for PL230326. Joystick: five positions27. WAKE UP button: used as regular button, and/or wake up the STM32 MCU from sleep28. USB to UART jumper29. LED jumper- Short the jumper to connect to default I/Os used in example code- Open the jumper to connect to custom I/Os via jumper wires30. Button/Joystick jumper- Short the jumper to connect to default I/Os used in example code- Open the jumper to connect to custom I/Os via jumper wiresPackage Contains1. Open429I-C development board x 12. USB type A plug to mini-B plug cable x 13. USB type A receptacle to mini-B plug cable x 14. 4-pin 2-pin wires pack x 15. USB power cable x 16. Software CD x 1

Read more less

OverviewOpen8S208Q80 is a STM8 development board that features a STM8S208MB device as the microcontroller. It supports further expansion with various optional accessory boards for specific application. The modular and open design makes it the ideal for starting application development with STM8 microcontroller.What is On Board1. STM8S208MB:the high performance STM8 MCU which features:- Core: 8-bit- Operating Frequency: 24 MHz(20 MIPS) Max- Operating Voltage: 2.7-5.5V- Package: LQFP80- I/Os: 68- Memories: 128kB Flash, 6kB SRAM, 2kB EEPROM- Communication Interfaces: 1 x SPI, 1 x I2C, 2 x UART, 1 x CAN, 12 x PWM, 16 x ADC- Debugging/Programming: SWIM2. AMS1117-3.3: 3.3V voltage regulator3. Power switch4. Power indicator5. LEDs: Convenient for indicating I/O status and/or program running state6. Reset button7. User keys: For I/O input test and/or program control8. Joystick: Five positions9. 8M crystal oscillator10. Adjustable resistor: For LCD12864 contrast adjustment11. UART1 interface: For connecting UART peripherals, such as RS232, RS485, USB TO UART, etc.12. CAN interface: For connecting CAN modules13. PS/2 interface: For connecting PS/2 devices, such as keyboard and/or mouse14. SPI interface: For connecting SPI peripherals, such as DataFlash (AT45DBxx), SD card, MP3, etc.15. 16 I/Os interface: For connecting accessory boards which using I/O control, such as FT245 USB FIFO, 8 SEG LED, etc.16. IC interface: For connecting I2C peripherals, such as I/O expander (PCF8574), EEPROM (AT24Cxx), etc.17. UART3 interface: For connecting UART peripherals, such as RS232, RS485, USB TO UART, etc.18. Graphic multi-color LCD interface: For connecting 2.2 inch multi-color touch screen LCD which using SPI control19. Graphic dot-matrix LCD interface: For connecting graphic LCDs such as LCD1286420. 1-WIRE interface: V connecting 1-WIRE devices (TO-92 package), such as temperature sensor (DS18B20), electronic registration number (DS2401), etc.21. 5V DC jack22. Custom crystal socket23. VCC power input/output: Usually used as power output, also common-grounding with other user board24. MCU pins connector: All the MCU pins are accessible on expansion connectors for further expansion25. SWIM interface: For debugging/programming26. User keys jumper27. Joystick jumper28. 1-WIRE jumper29. LEDs jumper30. PS/2 jumper31. LCD interface selection jumper- Short the jumper for dot-matrix LCD- Open the jumper for multi-color LCD32. VDD selection jumper33. Crystal selection jumper34. VREF selection jumper35. For jumpers 26-30:- Short the jumper to connect to I/Os used in example code;- Open the jumper to connect to other custom pins via jumper wires.Package Contents1. Open8S208Q80 development board x 12. 4-pin wire x 23. 2-pin wire x 24. USB power cable x 15. User guide CD x 1

Read more less

1. Resolution: 1.58 MP (color), 1456 × 10882. CMOS diagonal size: 6.3mm3. Pixel size: 3.45μm × 3.45μm4. Output: RAW105. Adjustable back focus (12.5~22.4mm)6. The lens supports C-mount / CS-mount (including C-CS adapter)7. IR CUT FILTER integration8. Tripod: 1/4″-209. Weight: 41 grams10. Data cable length: 150 mm11. Based on IMX296 sensor with a resolution of 1.6MP12. Capable of capturing fast moving objects without rolling shutter jelly effect, ideal for fast motion photography and machine vision applications13. With a large pixel size of 3.45μm × 3.45μm providing high light sensitivity, the global shutter camera can operate at short exposure times (as low as 30μs with sufficient light)14. The global shutter camera includes a C to CS mount adapter for industrial lenses with C or CS mount15. Compatible with all Raspberry Pi series boards (Extra adapter required for Raspberry Pi Zero or Compute Module series)16. Global shutter, clearer imaging17. The global shutter eliminates the jelly effect when shooting fast-moving objects, which is more suitable for high-speed motion capturePacking list:Global shutter camera x 1C-CS adapter x 1Dust cap x 1screwdriver x 1FFC ribbon x 1box x 1

Read more less

Camera module, 2 MegapixelFeatures1. 2 Megapixel2. Array size: UXGA 1622X12003. Power supply: 3.3V4. IO voltage level: 1.7V~3.3V DC5. Output formats:- YUV(422/420)/YCnCr422- RGB565/555- 8-bit compressed data6. Max image transfer rate:- UXGA/SXGA 15fps- UXGA/SXGA 30fps- SVGA 30fps- CIF 60fps

Read more less

1. Pixels: 5MP 2. Sensor: OV5640 3. Interface: USB 2.0 4. Camera: Sensor size 1/4 inch 5. Aperture (F): 2.8 6. Focal length (EFL): 3.29 mm 7. Field of view (FOV): 68 degree 8. Distortion: Less than 1% 9. Focusing(B): AF Auto-Focus; 10. Image Format support: MJPG, YUV422 11. Static image resolution: 2592 x 1944 12. Video recording: 15 FPS 2592 x 1944, 30 FPS 1920 x 1080, 30 FPS 1280 x 720 13. Operating voltage: 5V +/- 5% 14. Camera size: 8.5 x 8.5 mm 15. Module size: 9 x 62 mm

Read more less

Features1. Pixels: 5 megapixel2. Resolution: 2592x19443. Sensor: OV5640- 1.4um x 1.4um pixel with OmniBSI technology, high sensitivity, low crosstalk, low noise- Automatic image control functions: AEC, AWB, ABF, ABLC, etc.- Image quality controls: color saturation, hue, gamma, sharpness, lens correction, etc.- Supports image scaling, panning, windowing, etc.4. Lens:- CCD size: 1/4inch- Aperture (F): 2.5- Focal Length: 2.0mm- Diagonal: 170 degree (fisheye)5. Output Formats:- YUV(422/420)/YCbCr422- RGB565/555/444- CCIR656- RAW RGB- Compressed Data6. Operating Voltage: 3.3V7. Control Interface: SCCB (I2C compatible)8. Data Interface: DVP 8-bit9. Dimension: 35.70mm x 23.90mm

Read more less

Features1.Pixels: 5 megapixel2.Resolution: 2592x19443.Sensor: OV5640 3.1 1.4um x 1.4um pixel with OmniBSI technology, high sensitivity, low crosstalk, low noise 3.2 Automatic image control functions: AEC, AWB, ABF, ABLC, etc. 3.3 Image quality controls: color saturation, hue, gamma, sharpness, lens correction, etc. 3.4 Supports image scaling, panning, windowing, etc.4.Lens: 4.1 CCD size: 1/4inch 4.2 Aperture (F): 2.8 4.3 Focal Length: 2.8mm 4.4 Diagonal: 63 degree5.Output Formats: 5.1 YUV(422/420)/YCbCr422 5.2 RGB565/555/444 5.3 CCIR656 5.4 RAW RGB 5.5 Compressed Data6.Operating Voltage: 3.3V7.Control Interface: SCCB (I2C compatible)8.Data Interface: DVP 8-bit9.Dimension: 35.70mm × 23.90mm

Read more less

Camera Module Based on OV5640 Image Sensor, 5 Megapixel (2592x1944), Auto Focusing with Onboard Flash LEDFeatures1. Pixels: 5 megapixel2. Resolution: 2592x19443. Auto focusing by detecting the object distance4. Onboard flash LED, allowed to take pictures in the dark5. Sensor: OV5640- 1.4um x 1.4um pixel with OmniBSI technology, high sensitivity, low crosstalk, low noise- Automatic image control functions: AEC, AWB, ABF, ABLC, etc.- Image quality controls: color saturation, hue, gamma, sharpness, lens correction, etc.- Supports image scaling, panning, windowing, etc.6. Lens:- CCD size: 1/4inch- Aperture (F): 2.8- Focal Length: 3.37mm (adjustable)- Diagonal: 67.4 degree7. Output Formats:- YUV(422/420)/YCbCr422- RGB565/555/444- CCIR656- RAW RGB- Compressed Data8. Operating Voltage: 3.3V9. Control Interface: SCCB (I2C compatible)10. Data Interface: DVP 8-bit11. Dimension: 35.70mm x 23.90mm

Read more less

1. Pixels: 5MP 2. Sensor: OV5640 3. Interface: USB 2.0 4. Camera: Sensor size 1/4 inch 5. Aperture (F): 2.8 6. Focal length (EFL): 3.29 mm 7. Field of view (FOV): 68 degree 8. Distortion: Less than 1% 9. Focusing(C): FF Fixed-Focus 10. Image Format support: MJPG, YUV422 11. Static image resolution: 2592 x 1944 12. Video recording: 15 FPS 2592 x 1944, 30 FPS 1920 x 1080, 30 FPS 1280 x 720 13. Operating voltage: 5V +/- 5% 14. Camera size: 8.5 x 8.5 mm 15. Module size: 9 x 62 mm

Read more less

1. 1MP, global shutter, 120 degree FOV, OV9281-120 mono camera, compatible with Raspberry Pi series boards 2. The global shutter eliminates jello-effect while shooting fast moving objects, more suitable for high frame rate capturing 3. Working with Raspberry Pi, direct connect to Raspberry Pi different variants including 4B / 3B+ / 3A+ / 3B / 2B / B+ / A+, extra FPC cable is equired for Zero / Zero 2 W series Specifications: 1. Sensor: OV9281 2. CMOS size: 1/4 inch 3. Camera type: Mono 4. Pixels: 1MP (1280 x 800) 5. Shutter: Global Shutter 6. Aperture: F2.5 7. Distortion: Less than 7.5% 8. Field of vies: 120 degree 9. Focal length: 3.15mm 10. Focusing: Fixed focus Package List: 1. OV9281-120 Camera x 1 2. 15-pin FFC (opposite sides contact) x 1

Read more less

Overview1. The OV9655 Camera Board is a simple digital camera based on OV9655.2. The OV9655 Camera Board makes it possible to take photos and/or record video with your development board.FeaturesOV9655, camera, control interface

Read more less

Overview1. The PCF8563 RTC Board provides the real-time clock/calendar function, which can be driven by a battery on board and works independently even when the MCU is turned off.2. The PCF8563 RTC Board features I2C pinheader on one side, and I2C connector on the opposite side. Hence, its more flexible to connect the board to your development system. The board also supports I2C cascading, allowing the use of multi module connected to the I2C bus at the same time by connecting the pinheader and connector.FeaturesPCF8563, I2C pinheader, I2C connector, 3.3V battery included

Read more less

Overview1. The PCF8591 AD DA Board features an 8-bit A/D Converter & D/A Converter PCF8591 with four analog inputs, one analog output and a serial I2C-bus interface.2. The PCF8591 AD DA Board features I2C pinheader on one side, and I2C connector on the opposite side. Hence, it's more flexible to connect the board to your development system. The board also supports I2C cascading, allowing the use of multi module connected to the I2C bus at the same time by connecting the pinheader and connector.FeaturesPCF8591, I2C pinheader, I2C connector, Adjustable resistor, Analog input for A/Dconversion, Analog output for D/A conversion, Address pins jumper

Read more less

Features:1. For M.2 M interface to PCIe ports: M2-PCIe-Switch-4P Supports 1-Ch M.2 M To 4-Ch PCIe X1 (Note: the output are PCIeX1 ports, not the USB ports); PCIe-X1-TO-PCIe-X16-Cable supports PCIe X1 To PCIe X162. Reinforcement design, better protection3. Multi-layer circuit boards for lossless transmission4. Neat interface layout: Can effectively reduce interface interference and ensure stable data transmission5. Expand To 4-Ch PCIe port: Suitable for application scenarios that require multiple PCIe ports at the same timeM2-PCIe-Switch-4P1. Transfer interface: PCIe X1 female port x 4, M.2 Mkey male port x 12. Operating system: Windows / linux3. Dimensions: 80.0 x 22.0mmPCIe-X1-TO-PCIe-X16-Cable1. Transfer interface: PCIe x 1 female port x 1, PCIe X16 port x 12. Power supply interface:- 6PIN header x 2- 4PIN header x 1-SATA 15PIN header x 13. Dimensions: 119.80 x 44.83mm

Read more less

Overview1. Infrared detection, eliminating the interferences of external stray light2. Schmitt trigger, stable wave form and signals3. Signal output indicator (while breaking the beam, outputs low level, the indicator lights up)Specifications1. Power: 3.3V ~ 5V2. Dimension: 26.8mm × 15mm × 18.7mm3. Mounting holes size: 3mm4. Gap width: 6mmApplications- Motor speed detection- Pulse counterHow to UseIn the case of working with a MCU:- VCC ↔ 3.3V ~ 5V- GND ↔ GND- DOUT ↔ MCU.IO (digital output)

Read more less

FeaturesSmart robot is project of electronic enthusiasts, and there have been several robots based on Raspberry Pi Zero W, 3B+, 4B in Waveshare product line. Now, here comes the Pico version: PicoGo! The PicoGo is a smart mobile robot based on Raspberry Pi Pico, it includes ultrasonic module, LCD module, Bluetooth module, line following module, and obstacle avoidance module, all these functions are highly integrated for easily achieving IR obstacle avoidance, auto line following, BT/IR remote control, and more. With various advanced features, it will help you fast get started with smart robot design and development. PicoGo smart mobile robot features: 1. Standard Raspberry Pi Pico header, supports Raspberry Pi Pico series 2. Battery protection circuit: over charge/discharge protection, over current protection, short circuit protection, reverse proof, more stable and safe operating 3. Recharge/Discharge circuit, allows programming/debugging concurrently while recharging 4. 5-ch infrared sensor, analog output, combined with PID algorithm, stable line tracking 5. Onboard multiple smart robot sensors like line tracking, obstacle avoidance, no more messy wiring 6. 1.14 inch IPS colorful LCD display, 240 x135 pixels, 65K colors 7. Integrates BT module, allows teleoperations like robot movement, RGB LED display color, buzzer, etc. by using mobile phone APP 8. N20 micro gearmotors, with metal gears, low noise, high accuracy 9. Colorful RGB LED, pretty cool! Raspberry Pi Pico controller board features: 1. RP2040 microcontroller chip designed by Raspberry Pi in the United Kingdom 2. Dual-core Arm Cortex M0+ processor, flexible clock running up to 133 MHz 3. 264KB of SRAM, and 2MB of on-board Flash memory 4. USB 1.1 with device and host support 5. Low-power sleep and dormant modes 6. Drag-and-drop programming using mass storage over USBPackage List1. Raspberry Pi Pico (pre-soldered header) x1 2. PicoGo base board x1 3. PicoGo acrylic panel x1 4. 1.14inch LCD Module x1 5. Ultrasonic sensor x1 6. 5V 3A power supply x1 7. IR remote controller x1 8. USB-A to micro-B cable 1.2m x1 9. PH2.0 8Pin cable 5cm opposite side headers x1 10. Mini cross wrench sleeve x1 11. Screwdriver x1 12. Screws and standoffs pack x1

Read more less

FeaturesSmart robot is project of electronic enthusiasts, and there have been several robots based on Raspberry Pi Zero W, 3B+, 4B in Waveshare product line. Now, here comes the Pico version: PicoGo! The PicoGo is a smart mobile robot based on Raspberry Pi Pico, it includes ultrasonic module, LCD module, Bluetooth module, line following module, and obstacle avoidance module, all these functions are highly integrated for easily achieving IR obstacle avoidance, auto line following, BT/IR remote control, and more. With various advanced features, it will help you fast get started with smart robot design and development. PicoGo smart mobile robot features: 1. Standard Raspberry Pi Pico header, supports Raspberry Pi Pico series 2. Battery protection circuit: over charge/discharge protection, over current protection, short circuit protection, reverse proof, more stable and safe operating 3. Recharge/Discharge circuit, allows programming/debugging concurrently while recharging 4. 5-ch infrared sensor, analog output, combined with PID algorithm, stable line tracking 5. Onboard multiple smart robot sensors like line tracking, obstacle avoidance, no more messy wiring 6. 1.14 inch IPS colorful LCD display, 240 x135 pixels, 65K colors 7. Integrates BT module, allows teleoperations like robot movement, RGB LED display color, buzzer, etc. by using mobile phone APP 8. N20 micro gearmotors, with metal gears, low noise, high accuracy 9. Colorful RGB LED, pretty cool! Raspberry Pi Pico controller board features: 1. RP2040 microcontroller chip designed by Raspberry Pi in the United Kingdom 2. Dual-core Arm Cortex M0+ processor, flexible clock running up to 133 MHz 3. 264KB of SRAM, and 2MB of on-board Flash memory 4. USB 1.1 with device and host support 5. Low-power sleep and dormant modes 6. Drag-and-drop programming using mass storage over USBPackage List1. Raspberry Pi Pico (pre-soldered header) x1 2. PicoGo base board x1 3. PicoGo acrylic panel x1 4. 1.14inch LCD Module x1 5. Ultrasonic sensor x1 6. 5V 3A power supply x1 7. IR remote controller x1 8. USB-A to micro-B cable 1.2m x1 9. PH2.0 8Pin cable 5cm opposite side headers x1 10. Mini cross wrench sleeve x1 11. Screwdriver x1 12. Screws and standoffs pack x1

Read more less

Features1. Adopt PL2303GS new version device 2. Support windows XP/7/8/10/11/... 3. 3x VCCIO power mode via jumper setting: - VCCIO - 5V: 5V output - VCCIO - 3.3V: 3.3V output 4. Open the jumper: powered from target board (1.8V/2.5V/3.3V/5V) 5. 3x LED indicators: TXD, RXD, PWRPackage List1. PL2303 USB UART Board (type A) V2 x1 2. 4-pin custom connector jumper wire x1

Read more less

Specification1. POE: Integrates 802.3af-compliant PoE circuit (5V/2.5A) 2. USB: USB 2.0 x 4 3. GPIO: Raspberry Pi 40 PIN GPIO x 1 4. Header: - RS485 x 1 - RS232 x 1 - PCIe Gen 2 x 1 5. HD media interface: HDMI x 2, supports 4K 30fps output 6. DSI display: MIPI DSI x 2 (15pin 1.0mm FPC) 7. CSI camera: MIPI CSI-2 x 2 (15pin 1.0mm FPC) 8. Power input: 5V 9. FAN: 5V / 12V (Allows speed adjustment and measurement) 10. RTC: Real-time clock with battery socket and ability to wake Compute Module 4 11. RJ45 Ethernet: Gigabit Ethernet 12. CM4 slot: Suitable for all variants of Compute Module 4 13. SD card slot: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 14. Size: 124.50 x 108.80mmPackage List1. Compute Module 4 PoE Board (B) x 1 2. Metal case (top and bottom) x 1 3. Fan-4010-PWM-12V x 1 4. Screwdriver x 1 5. Screws pack x 1 6. 5V 3A USB-C power adapter x 1

Read more less

Specification1. POE: Integrates 802.3af-compliant PoE circuit (5V/2.5A) 2. USB: USB 2.0 x 4 3. GPIO: Raspberry Pi 40 PIN GPIO x 1 4. Header: - RS485 x 1 - RS232 x 1 - PCIe Gen 2 x 1 5. HD media interface: HDMI x 2, supports 4K 30fps output 6. DSI display: MIPI DSI x 2 (15pin 1.0mm FPC) 7. CSI camera: MIPI CSI-2 x 2 (15pin 1.0mm FPC) 8. Power input: 5V 9. FAN: 5V / 12V (Allows speed adjustment and measurement) 10. RTC: Real-time clock with battery socket and ability to wake Compute Module 4 11. RJ45 Ethernet: Gigabit Ethernet 12. CM4 slot: Suitable for all variants of Compute Module 4 13. SD card slot: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 14. Size: 124.50 x 108.80mmPackage List1. Compute Module 4 PoE Board (B) x 1 2. Metal case (top and bottom) x 1 3. Fan-4010-PWM-12V x 1 4. Screwdriver x 1 5. Screws pack x 1 6. 5V 3A USB-C power adapter x 1

Read more less

Features1. PoE UPS Base For CM4: Uninterruptible power supply, powering the CM4 while recharging 2. Connecting With Compute Module 4: Standard CM4 socket and color-coded Raspberry Pi 40PIN GPIO header. Suitable For Compute Module 4 Lite/EMMC Series Module 3. Uninterruptible Power: It is able to charge the batteries and provide power output for the system at the same time from external power supply. Automatically switch over to batteries output if external power supply is unavailable, keeps the system running without any trouble 4. Multi Power Supply Options: - Three external power supply options: USB interface, wide voltage DC, and PoE - When connected to the external power supply, the system will be powered and the battery will be charged at the same time, and the battery will be in a disconnected status after being fully charged, so as to avoid battery life damaging caused by frequently charging and discharging - When the external power supply is insufficient, the battery will provide power output together with the external power supply at the same time to ensure system normal operation - When the external power supply is connected, the system will keep running normally even when the battery fails or is taken out. When the external power supply is disconnected, it will automatically switch over to batteries output without interrupting the system operation 5. Safe And Stable Circuit Design: Protection circuits for over charge/discharge, over current, short circuit, and reverse-proof along with the standalone resettable fuse for each battery, more safe and stable 6. Real Time Monitoring: Monitoring the batteries voltage, current, power, and remaining capacity via I2C. (When the voltage dips too low, it is possible to save files properly and then shutdown the system by software, to avoid any data loss) Note: The 18650 batteries are not includedSpecifications1. CM4 socket: Suitable for all variants of Compute Module 4 2. Battery support: Parallel 18650 Li-ion battery x 3 (NOT included) 3. Networking: Gigabit Ethernet RJ45 connector, integrates 802.3af-compliant PoE circuit (5V/2.5A) 4. USB: USB 2.0 Type A ?? 4 5. Connector: - Raspberry Pi 40PIN GPIO header - M.2 M KEY slot, for connecting NVME SSD, or communication module with PCIE M.2 M KEY interface 6. Display: MIPI DSI port x 1 (22pin 0.5mm FPC connector) 7. Camera: MIPI CSI-2 port x 2 (22pin 0.5mm FPC connector) 8. Video: HDMI x 2, supports 4K 30fps output 9. RTC: Real-time clock with battery socket and ability to wake Compute Module 4 10. Storage: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 11. Fan: Allows speed adjustment and measurement, 5V / 12V 12. Indicator: - M.2 status LED - CM4 status LED 13. Power input7-36V 14. Dimensions: 175.0 x 108.0mm

Read more less

1. POE power input: 37-57V2. Power output: 5V/2.5A3. Network standard: IEEE 802.3af PoE4. Size: 65x32mm5. Support Raspberry Pi 3B+/4B, compatible with Raspberry Pi official case.6. PoE (Power over Ethernet) function, in line with IEEE 802.3af standard.7. Fully isolated switch mode power supply (SMPS)8. Smaller, more flexible, and more compact component layout.

Read more less

FeaturesThis is a RS485 device data acquisitor / IoT gateway designed for industrial environment. It combines multi functions in one, including serial server, Modbus gateway, MQTT gateway, RS485 to HTTPD Client, etc. With RS485, WIFI and Ethernet ports, the module can realize functions such as serial to WIFI, serial to Ethernet, Ethernet to WIFI and so on. Using screw terminals for power input, it supports 5~36V wide range power supply. Rail-mount V0 flame-retardant case design, small in size, easy to install. It is suitable for applications like data acquisition, IoT gateway, safety & security IoT, and intelligent instrument monitoring...SpecificationsOutline: 1. Communication interface: RS485, screw terminal 2. Power supply: 5 ~ 36V DC, screw terminal 3. Case: PC + ABS, V0 flame retardant grade 4. Dimensions: L x W x H: 109.66 x 28 x 64.71 mm Comunication: 1. Ethernet: 10 / 100M auto-negotiation RJ45 connector 2. WIFI: 802.11b/g/n compliant 3. Serial port: RS485 interface (Anti-surge, Lightningproof, Over-current protection) Wireless specification: 1. Frequency Band: 2.412 ~ 2.484 GHz 2. Wireless network: Station / AP / AP+Station Mode 3. Security mechanism: WPA-PSK / WPA2-PSK 4. Encryption type: TKIP / AES 5. Transmitting power: - 802.11b: +19dBm (11Mbps) - 802.11g: +18dBm (54Mbps) - 802.11n: +17dBm (HT20, MCS7); +17dBm (HT40, MCS7) 6. Receiving sensitivity: - 802.11b: -89dBm (11Mbps) - 802.11g: -81dBm (54Mbps) - 802.11n: -73dBm (HT20, MCS7); -71dBm (HT40, MCS7) Serial specification: 1. Baudrate: 300 ~ 460800 bps 2. Parity bit: None, odd, even, mark, space 3. Data bit: 5 ~ 9 bits 4. Flow control: N/A Software 1.Protocol: TCP / UDP / ARP / ICMP / DHCP / DNS / HTTP / MQTT 2. Configuration: Host, web browser, serial AT command 3. Communication method: TCP/IP direct communication, VCOM 4. Operating mode: Transparent transmission, serial command, HTTPD Client, Modbus TCP to Modbus RTU Environmental requirements 1. Working temperature: -40 ~ 85 degree C 2. Storage temperature: -45 ~ 125 degree C 3. Humidity range: 5% ~ 95% relative humidityPackage List1. RS485 TO WIFI/ETH x 1 2. Antenna x 1

Read more less

1. Size: 5.5 inches2. Port: HDMI3. Display panel: IPS, 2K resolution4. Touch port: USB5. Support Raspberry Pi operating system, 10-point touch.6. Support Ubuntu / Kali, single touch.7. Only Raspberry Pi 4B and CM4 have enough CPU performance to fully drive this 2K monitor8. When using Raspberry Pi 3B+/Pi 3B/Zero 2w/Zero w, only the default portrait display is supported and cannot be rotated.9. This chassis only supports Raspberry Pi 4B

Read more less

Features1. Raspberry Pi camera, supports all revisions of the Pi2. Embedded removable IR-CUT filter, eliminating color distortion in the daylight3. Comes with infrared LED, supports night vision4. 5 megapixel OV5647 sensor5. Adjustable focus distance6. Camera specifications- CCD size: 1/4 inch- Aperture (F): 1.2- Focal Length: 8mm- Angle of View (diagonal): 40 degree- Sensor best resolution: 1080p7. 4 screw holes- Used for attachment- Provides 3.3V power output- Supports connecting infrared LED and/or fill flash LED8. Dimension: 31mm x32mmNote: To use the camera with Raspberry Pi Zero / Zero W / Zero WH, you need to buy a specific cable: Raspberry Pi Zero v1.3 Camera CableNote: The actual image pixels is 5MP, which depends on the sensor, so it doesn't matter that there is a 3MP silk mark on the camera.Package Contents1. RPi IR-CUT Camera (B) x12. Infrared LED Board (B) x23. 15-pin FFC (opposite sides contact) x1

Read more less

Product Overview1. The Raspberry Pi PoE+ HAT is a Power Over Ethernet (PoE+) accessory for the Raspberry Pi 3B+/4B. Compared to its predecessor Raspberry Pi PoE HAT, it features better cooling effect, implementing the 802.3af/at standard with 5V DC/4A larger power output, providing enough power for both Raspberry Pi 3B+/4B at max load and other peripherals at the same time. 2. By using this small HAT and some proper 802.3af/at-compliant power sourcing equipments, it is possible to provide both network connection and power supply for your Raspberry Pi in only one Ethernet cable.Specification1. PoE standard: 802.3af/at 2. Input voltage: 37-57 V DC, Class 4 device 3. Output voltage/current: 5V DC/4A 4. Current sense: Yes 5. Transformer design: Planar 6. Fan: Controllable brushless cooling fan, delivering 2.2 CFM for processor cooling 7. Fan size: 25 x 25mm 8. Feature: Fully isolated switched-mode power supply 9. Compatible with: Raspberry Pi 3B+/4BPackage List1. Raspberry Pi PoE+ HAT x1 2. Standoffs pack x1

Read more less

1. Using pogo pin connection, the Zero 2W can be easily attached 2. Easily compatible with the interfaces of Raspberry Pi 3B / 3B+ boards 3. Onboard headphone jack(extended from USB) and an additional speaker header 4. Onboard 4-ch USB ports, compatible with USB 2.0 / 1.1 transmission 5. Onboard RTL8152B Ethernet chip, support 1-ch RJ45 Ethernet port, 10 / 100 M adaptive 6. Not compatible with the first generation Zero Package List: 1. Zero-to-Pi3-Adapter (B) x 1 2. HD-MI Adapter x 1

Read more less

1. Zero can be easily attached via specially designed connectors 2. Easily compatible with the interfaces of Raspberry Pi 3B / 3B+ boards 3. The same GPIO header height as 3B, easily connecting with 3B series HATs or development projects 4. Onboard 4-ch USB ports, compatible with USB 2.0 / 1.1 transmission 5. Onboard RTL8152B Ethernet chip, support 1-ch RJ45 Ethernet port, 10 / 100 M adaptive

Read more less

1. Raspberry Pi Camera, supports only Raspberry Pi Zero V1.3 and Raspberry Pi Zero W2. 5 megapixel OV5647 sensor3. Camera specifications- CCD size : 1/4inch- Focal Length : 3.51mm- Angle of View (diagonal) : 69.1 degree- Sensor best resolution : 1080p4. 2592 × 1944 still picture resolution5. Support 1080p30fps, 720p60fps and 640x480p60/90fps video record6. Dimension: 60mm × 11.5mm × 5mm

Read more less

1. Pixel: 64 x 32=2048 dots2. Pitch: 2.5mm3. Pixel format: 1R1G1B4. Viewing angle: greater than 140 degrees5. Control mode: synchronous6. Drive: 1/16 scan7. Connector: HUB758. Power supply: V / 2.5A (VH4 connector input)9. Power: within 12W10. Size: 16 x 8cmFeatures:1. 2048 independent RGB led, full color display, adjustable brightness2. 64x32 pixels, 2.5mm pitch, allows displaying text, color images or animations 3. 160x80mm size, moderate size, suitable for DIY desktop display or wall mount display4. Two HUB75 headers on board, 1 for controller data input, 1 output, chain support5. Provide open source development resources (for Raspberry Pi / Raspberry Pi Pico / ESP32 / Arduino, etc.)

Read more less

FeaturesBy nightfall, the dazzling neon lights of the streets and alleys illuminate the whole city making it more dynamic. Obviously, the Full-Color LED Matrix Panel is playing an important role. Maybe be on the doors of shops, maybe be on the bus or the taxi, you can always see animations or advertisement videos. Does it look cool? Why not have a try? 1. 4096 individual RGB LEDs, full-color display, adjustable brightness 2. 64 x 64 pixels, 3mm pitch, allows displaying text, colorful image, or animation 3. 192 x 192mm dimensions, moderate size, suitable for DIY desktop display or wall mount display 4. Onboard two HUB75 header, one for controller data input, one for output, chain support 5. Provides open source development resources and tutorials, for use with Raspberry Pi, Arduino, and so onSpecifications1. Dimensions: 192mm x 192mm 2. Pixels: 64 x 64=4096 dots 3. Spacing: 3mm 4. Pixel form: 1R1G1B 5. Viewing angle: greater than or equal to 160 degrees 6. Control Type: Synchronous 7. Driving: 1/32 scan 8. Connector: HUB75 9. Power supply: 5V / 4A (VH4 connector input) 10. Power: less than or equal to 20WPackage List1. RGB-Matrix-P3-64x64 LED matrix and accessories x 1 2. Power supply terminal adapter x 1 3. 16P wire about 30cm x 1

Read more less

Features1. Comes with RM500U-CN core module, supports 5G and LTE-A multi network types, supports 5G NSA and SA networking 2. Integrates extensive network protocols, with multi drivers and software support, compatible with different OS including Windows / Linux / Android 3. USB 3.1 port (USB 2.0 compatible) for connecting to PC, Raspberry Pi, or Jetson Nano host board to enable high speed 5G communication 4. Standard M.2 B KEY slot, compatible with different 5G modules: RM500U-CN / RM500Q-CN / RM500Q-GL series 5. Onboard UART, PWR, and RST control pin, built-in voltage level translator, enabled via DIP switch, for use with hosts like Raspberry Pi or Arduino 6. Onboard USB-C connector, enabled via switch, for connecting standalone power supply for the module, allows more loads, stable amd flexible power supply 7. Onboard power supply on/off switch, reset button and LED indicator, easy to turn on/off the module or monitor the operating status 8. 2x SIM card slot, dual card single standby, switchable via AT command 9. High efficiency power supply circuit, up to 3A output currentSpecificationsFrequency band: 1. 5G: - 5G NR: 3GPP Release 15 NSA/SA operation, Sub-6 GHz - 5G NR NSA: n41, n78, n79 - 5G NR SA: n1, n28, n41, n77, n78, n79 - Downlink: 4 x 4 MIMO n1, n41, n77, n78, n79 2. LTE: - LTE Category: Downlink Cat 12, uplink Cat 13 - LTE-FDD: B1, B2, B3, B5, B7, B8, B20, B28 - LTE-TDD: B34, B38, B39, B40, B41 - Downlink 2 x 2 MIMO: B1, B2, B3, B5, B7, B8, B20, B28, B34, B38, B39, B40, B41 3. UMTS: WCDMA: B1, B2, B5, B8 Data rate: 1. 5G SA Sub-6: Downlink 2 Gbps; uplink 1 Gbps 2. 5G NSA Sub-6: Downlink 2.2 Gbps; uplink 575 Mbps 3. LTE: Downlink 600 Mbps; uplink 150 Mbps 4. UMTS: Downlink 42.2 Mbps; uplink 11 Mbps Other: 1. Operating temperature: -30 degree C ~ +75 degree C 2. Extension temperature: -40 degree C ~ +85 degree C 3. Module dimensions: 30.0 x 52.0 x 2.3 (mm) 4. Module weight: 8.9 (g)Package List1. M.2 TO 4G/5G HAT x 1 2. RM500U-CN x 1 3. Antenna 4pcs x 1 4. IPEX adapter cable 4pcs x 1 5. 2*20PIN pin header x 1 6. 5V 3A Type-C power adapter x 1 7. Dual plug USB3.0 cable x 1 8. USB3.0 adapter x 1 9. USB2.0 adapter x 1 10. SMA protective cap 4pcs x 1 11. Screws pack x 1

Read more less

1. 5G wireless specifications-5G Sub-6G:SA: n1, n2, n3, n5, n7, n8, n12, n13, n14, n18, n20, n25, n26, n28, n29, n30, n38, n40, n41, n48, n66, n70, n71, n75, n76, n77, n78, n79NSA: n1, n2, n3, n5, n7, n8, n12, n13, n14, n18, n20, n25, n26, n28, n29, n30, n38, n40, n41, n48, n66, n70, n71, n75, n76, n77, n78, n79-4G:LTE-FDD: B1, B2, B3, B4, B5, B7, B8, B12, B13, B14, B17, B18, B19, B20, B25, B26, B28, B29, B30, B32, B66, B71LTE-TDD: B34, B38, B39, B40, B41, B42, B43, B48LAA:B46-UMTS: B1, B2, B4, B5, B8, B19-GNSS: GPS / GLONASS / Beidou (Beidou) / Galileo / QZSS (only supported by RM520N-GL)2. Data rate-5G Sub-6G:SA: 2.4 Gbps (DL) / 900 Mbps (UL)NSA: 3.4 Gbps (DL)/550 Mbps (UL)-LTE: 1.6 Gbps (DL)/200 Mbps (UL)-HSPA+ 42 Mbps (DL)/5.76 Mbps (UL)3. WIFI wireless specifications-WiFi standards: IEEE802.11b/g/n, IEEE802.11Wi-Fi 5(a/b/g/n/ac) compatible, 2.4GHz, 5.8GHz, 2T2R, support AP mode-Data rate: 2.4GHz: up to 300Mbps; 5.8GHz: up to 866Mbps-Authentication: Supports WEP, WPA, WPA2 and other encryption methods4. Interface-M.2: 1 connector, comes with 1 RM520N-GL module by default, supports other 5G modules-Mini PCIE: 3 connectors, equipped with 1 2.4GHz and 1 5.8GHz WiFi module, can connect more than 1 4G module-WAN: 1x 10/100/1000M Ethernet, auto-negotiation MDI/MDIX, built-in 1.5KV electromagnetic isolation protection(The WAN RJ45 can be used as a LAN RJ45 port, so there can be a total of 5 LAN RJ45 ports)-LAN: 4x 10/100/1000M Ethernet, auto-negotiation MDI/MDIX, built-in 1.5KV electromagnetic isolation protection-Serial port: 1x RS232 + 1x RS485, built-in ESD protection-SIM/UIM card slot: drawer-type SIM card slot to prevent the SIM card from falling off, with built-in 15KV ESD protection-Antenna interface: SMA standard antenna interface, equipped with 4x 5G antenna and 4x WiFi antenna by default-TF card slot: for external storage-Power supply: standard power interface, providing 12~24V input, embedded power reverse protection and overvoltage protection-RESET button: Press and hold for 5-10 seconds and release to restore the router to factory settings.-Indicators: PWR, SYS, 5G, 4G, WAN, LAN, TF, 2.4G, 5.8G status indicators5. Power supply-Power adapter: DC 12V/2A-Power input range: 12-24V-Power consumption: data mode: less than 1A@12V, idle mode: less than 500mA@l2V6. Physical parameters-Material: metal shell-Protection level: IP30-Operating temperature: -35 to 75 degrees Celsius-Storage temperature: -40 to 85 degrees Celsius-Relative humidity: 95 percent (non-condensing)-Product size: 219 x 117 x 36.8mm-Weight: 919 gramsPacking list:-RM520N-GL 5G Router x 1-5G antenna x 4-WiFi antenna x 4-12V power adapter x 1

Read more less

1. 5G wireless specifications-5G Sub-6G:SA: n1, n2, n3, n5, n7, n8, n12, n13, n14, n18, n20, n25, n26, n28, n29, n30, n38, n40, n41, n48, n66, n70, n71, n75, n76, n77, n78, n79NSA: n1, n2, n3, n5, n7, n8, n12, n13, n14, n18, n20, n25, n26, n28, n29, n30, n38, n40, n41, n48, n66, n70, n71, n75, n76, n77, n78, n79-4G:LTE-FDD: B1, B2, B3, B4, B5, B7, B8, B12, B13, B14, B17, B18, B19, B20, B25, B26, B28, B29, B30, B32, B66, B71LTE-TDD: B34, B38, B39, B40, B41, B42, B43, B48LAA:B46-UMTS: B1, B2, B4, B5, B8, B19-GNSS: GPS / GLONASS / Beidou (Beidou) / Galileo / QZSS (only supported by RM520N-GL)2. Data rate-5G Sub-6G:SA: 2.4 Gbps (DL) / 900 Mbps (UL)NSA: 3.4 Gbps (DL)/550 Mbps (UL)-LTE: 1.6 Gbps (DL)/200 Mbps (UL)-HSPA+ 42 Mbps (DL)/5.76 Mbps (UL)3. WIFI wireless specifications-WiFi standards: IEEE802.11b/g/n, IEEE802.11Wi-Fi 5(a/b/g/n/ac) compatible, 2.4GHz, 5.8GHz, 2T2R, support AP mode-Data rate: 2.4GHz: up to 300Mbps; 5.8GHz: up to 866Mbps-Authentication: Supports WEP, WPA, WPA2 and other encryption methods4. Interface-M.2: 1 connector, comes with 1 RM520N-GL module by default, supports other 5G modules-Mini PCIE: 3 connectors, equipped with 1 2.4GHz and 1 5.8GHz WiFi module, can connect more than 1 4G module-WAN: 1x 10/100/1000M Ethernet, auto-negotiation MDI/MDIX, built-in 1.5KV electromagnetic isolation protection(The WAN RJ45 can be used as a LAN RJ45 port, so there can be a total of 5 LAN RJ45 ports)-LAN: 4x 10/100/1000M Ethernet, auto-negotiation MDI/MDIX, built-in 1.5KV electromagnetic isolation protection-Serial port: 1x RS232 + 1x RS485, built-in ESD protection-SIM/UIM card slot: drawer-type SIM card slot to prevent the SIM card from falling off, with built-in 15KV ESD protection-Antenna interface: SMA standard antenna interface, equipped with 4x 5G antenna and 4x WiFi antenna by default-TF card slot: for external storage-Power supply: standard power interface, providing 12~24V input, embedded power reverse protection and overvoltage protection-RESET button: Press and hold for 5-10 seconds and release to restore the router to factory settings.-Indicators: PWR, SYS, 5G, 4G, WAN, LAN, TF, 2.4G, 5.8G status indicators5. Power supply-Power adapter: DC 12V/2A-Power input range: 12-24V-Power consumption: data mode: less than 1A@12V, idle mode: less than 500mA@l2V6. Physical parameters-Material: metal shell-Protection level: IP30-Operating temperature: -35 to 75 degrees Celsius-Storage temperature: -40 to 85 degrees Celsius-Relative humidity: 95 percent (non-condensing)-Product size: 219 x 117 x 36.8mm-Weight: 919 gramsPacking list:-RM520N-GL 5G Router x 1-5G antenna x 4-WiFi antenna x 4-12V power adapter x 1

Read more less

1. 5G wireless specifications-5G Sub-6G:SA: n1, n2, n3, n5, n7, n8, n12, n13, n14, n18, n20, n25, n26, n28, n29, n30, n38, n40, n41, n48, n66, n70, n71, n75, n76, n77, n78, n79NSA: n1, n2, n3, n5, n7, n8, n12, n13, n14, n18, n20, n25, n26, n28, n29, n30, n38, n40, n41, n48, n66, n70, n71, n75, n76, n77, n78, n79-4G:LTE-FDD: B1, B2, B3, B4, B5, B7, B8, B12, B13, B14, B17, B18, B19, B20, B25, B26, B28, B29, B30, B32, B66, B71LTE-TDD: B34, B38, B39, B40, B41, B42, B43, B48LAA:B46-UMTS: B1, B2, B4, B5, B8, B19-GNSS: GPS / GLONASS / Beidou (Beidou) / Galileo / QZSS (only supported by RM520N-GL)2. Data rate-5G Sub-6G:SA: 2.4 Gbps (DL) / 900 Mbps (UL)NSA: 3.4 Gbps (DL)/550 Mbps (UL)-LTE: 1.6 Gbps (DL)/200 Mbps (UL)-HSPA+ 42 Mbps (DL)/5.76 Mbps (UL)3. WIFI wireless specifications-WiFi standards: IEEE802.11b/g/n, IEEE802.11Wi-Fi 5(a/b/g/n/ac) compatible, 2.4GHz, 5.8GHz, 2T2R, support AP mode-Data rate: 2.4GHz: up to 300Mbps; 5.8GHz: up to 866Mbps-Authentication: Supports WEP, WPA, WPA2 and other encryption methods4. Interface-M.2: 1 connector, comes with 1 RM520N-GL module by default, supports other 5G modules-Mini PCIE: 3 connectors, equipped with 1 2.4GHz and 1 5.8GHz WiFi module, can connect more than 1 4G module-WAN: 1x 10/100/1000M Ethernet, auto-negotiation MDI/MDIX, built-in 1.5KV electromagnetic isolation protection(The WAN RJ45 can be used as a LAN RJ45 port, so there can be a total of 5 LAN RJ45 ports)-LAN: 4x 10/100/1000M Ethernet, auto-negotiation MDI/MDIX, built-in 1.5KV electromagnetic isolation protection-Serial port: 1x RS232 + 1x RS485, built-in ESD protection-SIM/UIM card slot: drawer-type SIM card slot to prevent the SIM card from falling off, with built-in 15KV ESD protection-Antenna interface: SMA standard antenna interface, equipped with 4x 5G antenna and 4x WiFi antenna by default-TF card slot: for external storage-Power supply: standard power interface, providing 12~24V input, embedded power reverse protection and overvoltage protection-RESET button: Press and hold for 5-10 seconds and release to restore the router to factory settings.-Indicators: PWR, SYS, 5G, 4G, WAN, LAN, TF, 2.4G, 5.8G status indicators5. Power supply-Power adapter: DC 12V/2A-Power input range: 12-24V-Power consumption: data mode: less than 1A@12V, idle mode: less than 500mA@l2V6. Physical parameters-Material: metal shell-Protection level: IP30-Operating temperature: -35 to 75 degrees Celsius-Storage temperature: -40 to 85 degrees Celsius-Relative humidity: 95 percent (non-condensing)-Product size: 219 x 117 x 36.8mm-Weight: 919 gramsPacking list:-RM520N-GL 5G Router x 1-5G antenna x 4-WiFi antenna x 4-12V power adapter x 1

Read more less

OverviewDetects clockwise/anti-clockwise rotations: degrees and lapsSpecifications1. Pulses per lap: 152. Power: 3.0V ~ 5.3V3. Dimension: 32.1mm * 15.4mm4. Mounting holes size: 2.0mmApplicationsPositioning in Industrial ControlsHow to UseIn the case of working with a MCU:1. VCC -- 3.0V ~ 5.3V2. GND -- Power supply ground3. SW -- MCU.IO (encoder button status)4. SIB -- MCU.IO (output status)5. SIA -- MCU.IO (output status)

Read more less

FeaturesBased on a high performance Cortex processor, combined with high-security commercial fingerprinting algorithm, the UART Fingerprint Sensor (D) features functionalities like fingerprint enrolling, image acquisition, feature finding, template generating and storing, fingerprint matching, and so on. Without any knowledge about the complicate fingerprinting algorithm, all you need to do is just sending some UART commands, to quickly integrate it into fingerprint verification applications which require small size and high precision. 1. Easy to use by some simple commands, you do not have to know any fingerprint technology, or the module inter structure 2. Commercial fingerprinting algorithm, supports functions like fingerprint enrolling, fingerprint matching, fingerprint image acquisition, and fingerprint feature uploading, stable performance, fast identification 3. Capacitive sensitive detection, just touch the collecting window lightly for fast verification 4. Highly integrated hardware, processor and sensor in one small chip, suitable for small size applications 5. Narrow stainless steel rim, supports 360 degree omni-directional verification 6. Embedded human sensor, the processor will enter sleep automatically, and wake up when touching, lower power consumption 7. Onboard UART connector, easy to connect with hardware platforms like STM32 and Raspberry Pi1.Specifications1. Sensor: Capacitive touch sensor 2. Resolution: 508 DPI 3. Image pixels: 160 x 160 4. Image greyscale: 8 5. Sensor dimension: R15.5 mm 6. Fingerprint capacity: 150 7. Matching time: Less than 500ms (1:N, and N Less than or equal 100) 8. False acceptance rate: Less than 0.001% 9. False rejection rate: Less than 0.1% 10. Operating voltage: 2.7~3.3V 11. Operating current: Less than 50mA 12. Sleep current: Less than 16uA 13. ESD: Contact discharge 8KV / aerial discharge 15KV 14. Communication port: UART 15. Baudrate: 19200 bps 16. Operating environment temperature: -20 degree C~70 degree C; Humidity: 40%RH~85%RH (no condensation) 17. Storage environment temperature: -40 degree C~85 degree C; Humidity: Less than 85%RH (no condensation)

Read more less