Products

1. Barcode scanning module (B) is a barcode / 2D code scanning module, which can quickly and accurately decode 1D or 2D codes on paper or screen through intelligent image recognition algorithm.2. Support multiple barcode formats and 4mil high density barcode scanning. 3. On-board USB and UART interface, which can be directly plugged into a computer or easily integrated into various embedded devices.4. Resolution: 640 x 4805. Scanning angle: pitch +/-65 degrees, skew +/-65 degrees, roll 360 degrees6. Scanning mode: sensing, continuous, manual (default)7. Precision: greater than or equal to 4 million8. Communication interface: USB keyboard mode (default), USB virtual port, UART port9. Light source: white (Lighting) + red (Aiming), both visible light10. Power supply: 5V/3.3V11. Current: 262mA at work, 75mA at standby, 108mA at boot12. Temperature: working temperature -20-60 degrees Celsius, storage -30-70 degrees CelsiusPacking list:Bar code scanning module (B) x1USB A-type plug to micro B plug cable x1PH2.0 4Pin data cable x1

Read more less

1. Input interface: HDMI x 32. Support 4K/2K 30Hz3. Built-in input equalizer, can automatically adjust the input signal4. Output interface: HD x15. Built-in output drive regulator, which can automatically adjust the output signal amplitude6. Support HDMI 1.4b and DVI1.0 standard7. Transmission speed: up to 3Gbps

Read more less

1. Resolution: 800 × 8002. Display interface: DSI3. Display panel: IPS4. Viewing angle: 170 degrees5. Touch type: capacitive touch6. Touch points: ten-point touch7. Touch interface: I2C8. Touch panel: tempered glass panel9. Touch panel process: full lamination10. Application scenarios: smart home, automotive equipment, consumer electronics, industrial equipment, etc.11. Screen size: about 3.4 inches12. Size ：approx. 11.5 x 1.7cmFeatures:1. IPS display panel with good display performance and wide viewing angle up to 170 degrees2. Can support 10-point touch, the actual number of touch points with the software system3. Tempered glass panel, hardness up to 6H4. Screen full lamination, good display, dustproof5. Backlight brightness can be adjusted by software6. Support Raspberry Pi OS, ten-point touch, need to install the driver7. Support Pi 4B/3B+/3A+, some CM3/3+/4 expansion boards need to purchase additional adapter cable

Read more less

1. 320x480 resolution, resistive touch control, 8:5 aspect ratio. 2. Supports any revision of Raspberry Pi (directly-pluggable). 3. Drivers provided (works with your own Raspbian/Ubuntu directly). 4. Size perfectly fits the Pi. 5. High quality immersion gold surface plating. 6. Support Raspbian system, enables your system to: - Take photos by touching (up to 17 camera modes). - Support software keyboard (system interaction without keyboard/mouse). 7. 3.5 inch RPi LCD (A) and 3.5 inch RPi LCD (B) are hardware compatible with each other (uses different driver), and can be mutually substituted in most cases. (A) for low cost ver. while (B) for IPS ver. with better displaying.

Read more less

Features1. 480 x 320 resolution, IPS screen, 65K colors, clear and colorful displaying effect 2. Dedicated touch controller, bringing more smooth touching effect than AD-controlled solutions 3. MicroSD card slot for storing images and direct displaying them easily 4. Programmable backlight control, power saving 5. Come with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples)Specification1. Operating voltage: 5V 2. Resolution: 480x320 pixels 3. Display color: 65K colorful 4. Communication interface: SPI 5. Display panel: IPS 6. Display size: 73.44 x 48.96 mm 7. Pixel size: 0.153 x 0.153 mm 8. Controller: ILI9488 9. Size: 86.00 x 57.20 mmPackage List1. Pico-ResTouch-LCD-3.5 x1 2. Standoffs pack x1

Read more less

1. 3.5 inch IPS screen, hardware resolution is 640 ?? 480. 2. 5-point capacitive touch, tempered glass panel, hardness up to 6H. 3. When used with Raspberry Pi, supports Raspberry Pi OS / Ubuntu / Kali and Retropie. 4. When used with Tinker Board 2, it supports Android / Debian. 5. Ubuntu is supported when used with Jetson Nano. 6. When used as a computer monitor, supports Windows 11/10/8.1/8/7. 7. Onboard dual touch circuit, optional USB Type-C or I2C touch, more application scenarios. 8. With 3.5mm audio and speaker interface, support HDMI audio output.

Read more less

FeaturesThe Pico-Eval-Board is an overall evaluation solution designed for Raspberry Pi Pico. With 3.5inch 65K colorful LCD display and misc helpful onboard components, this evaluation board allows you to try almost every on chip peripheral of the RP2040, eliminating the mess wiring. It is an ideal choice for user to fast get started with the Raspberry Pi Pico, as well as the RP2040 chip. 1. Standard Raspberry Pi Pico header, supports Raspberry Pi Pico series boards 2. 3.5 inch resistive touch screen, 65K colorful, bringing clear and vivid display effect 3. Standard 3.5mm audio jack, for headphone or other audio peripherals 4. Micro SD card slot through the SDIO interface, faster access speed than SPI interface 5. Integrates battery header and recharge circuit, allows it keep running without wired power supply 6. Other rich resources like buzzer, photoresistor, and RGB LED... 7. Comes with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples)Specification1. Operating voltage: 5V 2. Touch Type: Resistive 3. Resolution:480x320 pixels 4. Display color: 65K colorful 5. Communication BUS: SPI 6. Display panel: IPS 7. Display size: 73.44 x 48.96 mm 8. Pixel size: 0.153 x 0.153 mm 9. Controller: ILI9488/XPT2046 10. Size: 86.00 x 57.20 mmPackage List1. Pico-Eval-Board x 1 2. Standoff pack x 1

Read more less

1. 3.5-inch IPS display, hardware resolution 480 x 8002. 5-point capacitive touch, 170 degrees wide viewing angle, excellent display performance3. Optical lamination touch technology, better use4. Support Raspberry Pi OS/Ubuntu/Kali/WIN10 loT/Retropie, driver-free5. Interface: HD-MI interface, USB Type-C interface6. Size: 88.87 x 52.56mm7. Weight: 0.159 kgPacking list:3.5" 480x800 LCD display x 1HDMI flat cable ~1m x1USB Type-A to USB Type-C cable ~1m x1HD-MI to Micro HD-MI adapter x1

Read more less

Features1. No backlight, keeps displaying last content for a long time even when power down 2. Ultra low power consumption, basically power is only required for refreshing 3. SPI interface, requires minimal IO pins 4. Onboard voltage translator, compatible with 3.3V / 5V MCUs 5. Comes with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples)Specification1. Operating voltage: 3.3V/5V 2. Display color: Black, white 3. Resolution: 480x280 pixels 4. Grey scale: 4 5. Interface: 3-wire SPI, 4-wire SPI 6. Viewing angle: Greater than 170 degree 7. Partial refresh time: 0.3s 8. Full refresh time: 3s 9. Outline dimensions: 95.3 x 56.9mm 10. Display size: 81.12 x 47.32mm 11. Refresh power: 26.4mW (typ.) 12. Standby current: Less than 0.01uA (almost none) 13. Dot pitch: 0.169 x 0.169 mmPackage List1. Pico-ePaper-3.7 x 1 2. Standoff pack x 1

Read more less

Overview1. This is a 4 port USB hub for Raspberry Pi, provides more USB capability to your Pi, whats more, it features USB to UART converter for easy serial communication.2. It can work with various versions of the Pi, and the size of the board is designed to perfectly fit the Zero / Zero W.USB HUB HAT Features1. 4 USB Ports, compatible with USB2.0/1.12. Onboard USB to UART, convenient for Raspberry Pi serial debugging3. Onboard multi indicators, for monitoring the status of power, USB to UART, and each USB portWhat is on the USB HUB HAT1. Raspberry Pi GPIO interface: For connecting Raspberry Pi2. USB to UART: For controlling the Raspberry Pi via serial terminal3. USB HUB interface (bottom): For connecting the HUB to the Raspberry Pi USB port- Raspberry Pi Zero / Zero W: Connected via Micro USB connector- Raspberry Pi B+ / 2B / 3B / 3B+: Connected via Micro USB cable4. USB extended ports: USB1~USB45. USB port indicators: dedicated indicator for each USB port, D1~D4 for USB1~USB4 respectively6. Power indicator7. USB to UART indicator8. FE1.1S: USB HUB chip9. 12MHz crystal10. CP2102: USB to UART converterSpecifications1. Operating voltage: 5V2. Dimension: 65mm * 30mm3. Mounting hole size: 3.0mm4. Package contents:- USB HUB HAT x1- Micro USB connector x1- Micro USB cable x1- RPi screws pack (2pcs) x1

Read more less

Features: 1. SPI-compatible, easy to drive 2. Standard Raspberry Pi Pico header, supports Raspberry Pi Pico series 3. Come with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples) Specifications: 1. Operating voltage: 5V 2. DIGITS: 4 3. LED color: Red 4. Driver: 74HC595 5. Display part No.: FJ4401AH 6. Display size: 0.4 inch 7. Size: 52 x a??21m

Read more less

Overview1. Equip your micro:bit with this 4-DOF metal robot arm, and get started to explore the world of artificial intelligent robotic.2. This starter robotic arm kit includes: servo driver board, metal mechanical arm structure, and 4x metal gear servos. When used with the micro:bit, it is easy to control the arm by smart phone through Bluetooth connection.The Servo DriverAdopts Servo Driver for micro:bit:1. Micro:bit edge connector, directly pluggable2. I2C controlled, using only 2 pins3. Up to 16-Channel servo/PWM outputs, 12-bit resolution for each channel (4096 scales)4. Integrates 5V regulator, up to 3A output current, can be powered from battery through VIN terminal5. Standard servo interface, supports common used servo such as SG90, MG90S, MG996R, etc.6. Reserved I2C control pins, allows to work with other control boards7. Comes with development resources and manual (micro:bit graphical examples like Bluetooth/2.4G wir eless remote control)The Robot Arm Structure1. 4-DOF, large solid base, metal mechanical grasper2. Full aluminium alloy body, sandblasting oxidation surface, strong & durable3. Clever mechanical structure and mounting design, agile to control, easy to build3. Fitted with 4x metal gear servos (1x MG996R, 3x MG90S), large torque force, smooth movingPackage IncludeNote: micro:bit is NOT included.1. Metal arm parts x12. MG996R Servo x13. MG90S Servo x34. MG996R servo wheel x15. Servo Driver for micro:bit x16. Power adapter US plug 5V 3A Micro x17. Servo extension wire 150mm x18. Screws pack x19. Screwdrivers 2PCS x1

Read more less

Overview1. Equip your Raspberry Pi with this 4-DOF metal robot arm, and get started to explore the world of artificial intelligent robotic.2. This starter robotic arm kit includes: servo driver HAT, metal mechanical arm structure, and 4x metal gear servos. When used with the Raspberry Pi, it is easy to control the arm by smart phone through Bluetooth or WiFi connection.The Servo DriverAdopts Servo Driver HAT:1. Raspberry Pi connectivity, compatible with Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+, Jetson Nano2. I2C controlled, using only 2 pins3. Up to 16-Channel servo/PWM outputs, 12-bit resolution for each channel (4096 scales)4. Integrates 5V regulator, up to 3A output current, can be powered from battery through VIN terminal5. Standard servo interface, supports common used servo such as SG90, MG90S, MG996R, etc.6. Reserved I2C control pins, allows to work with other control boards7. Comes with development resources and manual (examples in python like Bluetooth/WiFi remote control)The Robot Arm Structure1. 4-DOF, large solid base, metal mechanical grasper2. Full aluminium alloy body, sandblasting oxidation surface, strong & durable3. Clever mechanical structure and mounting design, agile to control, easy to build4. Fitted with 4x metal gear servos (1x MG996R, 3x MG90S), large torque force, smooth movingPackage ContentsNote: Raspberry Pi is NOT included.1. Metal arm parts x12. MG996R Servo x13. MG90S Servo x34. MG996R servo wheel x15. Servo Driver HAT x16. Power adapter EU standard USB output x17. Servo extension wire 150mm x18. Screws pack x19. Screwdrivers 2PCS x1

Read more less

Overview1. Equip your Raspberry Pi with this 4-DOF metal robot arm, and get started to explore the world of artificial intelligent robotic.2. This starter robotic arm kit includes: servo driver HAT, metal mechanical arm structure, and 4x metal gear servos. When used with the Raspberry Pi, it is easy to control the arm by smart phone through Bluetooth or WiFi connection.The Servo DriverAdopts Servo Driver HAT:1. Raspberry Pi connectivity, compatible with Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+, Jetson Nano2. I2C controlled, using only 2 pins3. Up to 16-Channel servo/PWM outputs, 12-bit resolution for each channel (4096 scales)4. Integrates 5V regulator, up to 3A output current, can be powered from battery through VIN terminal5. Standard servo interface, supports common used servo such as SG90, MG90S, MG996R, etc.6. Reserved I2C control pins, allows to work with other control boards7. Comes with development resources and manual (examples in python like Bluetooth/WiFi remote control)The Robot Arm Structure1. 4-DOF, large solid base, metal mechanical grasper2. Full aluminium alloy body, sandblasting oxidation surface, strong & durable3. Clever mechanical structure and mounting design, agile to control, easy to build4. Fitted with 4x metal gear servos (1x MG996R, 3x MG90S), large torque force, smooth movingPackage ContentsNote: micro:bit is NOT included.1. Metal arm parts x12. MG996R Servo x13. MG90S Servo x34. MG996R servo wheel x15. Servo Driver for micro:bit x16. Power adapter US plug 5V 3A Micro x17. Servo extension wire 150mm x18. Screws pack x19. Screwdrivers 2PCS x1

Read more less

Features1. Advanced Color ePaper (ACeP) technology, supports 7-Color display 2. No backlight, keeps displaying last content for a long time even when power down 3. Ultra low power consumption, basically power is only required for refreshing 4. Comes with development resources and manual (examples for Raspberry Pi/Jetson Nano/Arduino/STM32)Advantages Of EINK1. E-paper display utilizes microcapsule electrophoretic technology for displaying, the principle is: charged particles suspended in clear fluid will move to sides of microcapsule when electric field is applied, making the microcapsule become visible by reflecting ambient light, just as traditional printed paper. 2. E-paper display will clearly display images/texts under lamplight or natural light, requires no backlight, and features nearly up to 180 degrees viewing angle. It is usually used as e-reader due to its paper-like effect.Specification1. Operating voltage: 3.3V 2. Display color: ACeP 7-Color 3. Resolution: 640 x 400 pixels 4. Grey scale: 2 5. Interface: 3-wire SPI, 4-wire SPI 6. Standby current: Less than 0.01uA (almost none) 7. Refresh power: 50mW (typ.) 8. Full refresh time: 15s 9. Dimensions: 96.80 x 68.70mm 10. Display size: 66.9 x 29.06mm 11. Dot pitch: 0.135 x 0.135mm

Read more less

Overview1. This is an E-Ink display module, 4.2inch, 400x300 resolution, with embedded controller, communicating via SPI interface.2. Due to the advantages like ultra low power consumption, wide viewing angle, clear display without electricity, it is an ideal choice for applications such as shelf label, industrial instrument, and so on.Features1. No backlight, keeps displaying last content for a long time even when power down2. Ultra low power consumption, basically power is only required for refreshing3. SPI interface, for connecting with controller boards like Raspberry Pi/Arduino/Nucleo, etc.4. Onboard voltage translator, compatible with 3.3V/5V MCUs5. Comes with development resources and manual (examples for Raspberry Pi/Arduino/STM32)Specifications1. Operating voltage: 3.3V~5V2. Interface: 3-wire SPI, 4-wire SPI3. Outline dimension: 103.0mm × 78.5mm4. Display size: 84.8mm × 63.6mm5. Dot pitch: 0.212 × 0.2126. Resolution: 400 × 3007. Display color: black, white8. Grey level: 29. Full refresh time: 4s10. Refresh power: 26.4mW(typ.)11. Standby power: <0.017mW12. Viewing angle: >170 degree13. Weight: 0.052 kgInterface1. SYMBOL: DESCRIPTION2. VCC: 3.3V~5V3. GND: Ground4. DIN: SPI MOSI pin5. CLK: SPI SCK pin6. CS: SPI chip selection, low active7. DC: Data/Command selection (high for data, low for command)8. RST: External reset, low active9. BUSY: Busy status output, low activePackage contents1. 4.2inch e-Paper Module x12. PH2.0 20cm 8Pin x1

Read more less

Overview1. This is a serial interface E-Ink display module, 4.3 inch, 800×600 resolution, with embedded font libraries, ultra low power consumption.2. You do not have to know anything about the complex underlying details of e-Paper, nor the specific algorithms of displaying graphics, texts, and images. All it needs is the serial interface, and all it matters is your creativity.Features1. Easy to use, displays any contents via one serial interface, including geometric graphics, texts, and images2. Embedded font libraries, supports 32, 48 and 64 dot matrix GBK Chinese fonts and English fonts3. Built-in 128MB NandFlash, allows the font/image data to be stored in either an external TF card or the internal NandFlash4. 4 grey level displaying, 800×600 resolution5. Adjustable serial interface baud rate, 115200 by default when power up6. Powered from 3.3V to 5V, compatible with logic level7. Ultra low power consumption, sleeping current lower than 5mA8. Comes with host computer software, control it directly on your computerApplications1. e book2. Shopping mall POS3. Price label4. Industry instrumentPin Definitions1. VCC: 3.3V~5.5V2. GND: GND3. DOU : Serial data out4. DIN: Serial data in5. WAKE_UP: External wake up6. RST: External resetPackage Contents1.4.3inch e-Paper UART Module x11. XH2.54 6-pin cable ×1

Read more less

1. Resolution: 800 x 4802. Display interface: DSI3. Display panel: IPS4. Viewing angle: 160 degrees5. Touch screen models:- Touch type: capacitive touch- Touch points: 5 points touch- Touch interface: I2C- Touch panel: tempered glass panel6. Application scenarios: smart home, automotive equipment, consumer electronics, industrial equipment, etc.7. Screen size: about 4.3 inch8. Size:about 10.5 x 6.7 x 0.52cmFeatures:1. IPS display panel with good display performance and wide viewing angle of up to 160 degrees2. Integrated structure design, DSI one-line, easy to integrate integrated design, provide secondary development materials, help simple development3. Thinner and more space-saving, the driver circuit is integrated into the FPC, about 5mm thickness space can be4. Touch models capacitive five-point touch, flexible operation, through the I2C signal, lead to touch function, support five-point touch5. Touch model backlight brightness can be adjusted by software6. Support Raspberry Pi OS, 5-point touch, driver-free7. Support Ubuntu / Kali / WIN10 IoT, single-touch, driver-free8. Support Retropie, driver-free9. Support Pi 4B/3B+/3A+/3B/2B/B+/A+, some CM3/3+/4 backplanes need to buy adapter cable separately

Read more less

1. Resolution: 800 x 4802. Display interface: DSI3. Display panel: IPS4. Viewing angle: 160 degrees5. Touch screen models:- Touch type: capacitive touch- Touch points: 5 points touch- Touch interface: I2C- Touch panel: tempered glass panel6. Application scenarios: smart home, automotive equipment, consumer electronics, industrial equipment, etc.7. Screen size: about 4.3 inch8. Size:about 10.5 x 6.7 x 0.52cmFeatures:1. IPS display panel with good display performance and wide viewing angle of up to 160 degrees2. Integrated structure design, DSI one-line, easy to integrate integrated design, provide secondary development materials, help simple development3. Thinner and more space-saving, the driver circuit is integrated into the FPC, about 5mm thickness space can be4. Touch models capacitive five-point touch, flexible operation, through the I2C signal, lead to touch function, support five-point touch5. Touch model backlight brightness can be adjusted by software6. Support Raspberry Pi OS, 5-point touch, driver-free7. Support Ubuntu / Kali / WIN10 IoT, single-touch, driver-free8. Support Retropie, driver-free9. Support Pi 4B/3B+/3A+/3B/2B/B+/A+, some CM3/3+/4 backplanes need to buy adapter cable separately

Read more less

FeaturesRaspberry Pi 4B main features: 1. BCM2711B0 64 bit 1.5GHz quad core processor with 4GB memory 2. It supports 4K 60fps high-resolution dual screen display by dual micro HDMI interface 3. Gigabit Ethernet port, Bluetooth 5.0 BLE, 2.4G / 5G dual-band WIFI 4. Dual USB2.0 interface, also with dual USB3.0 interface, faster transmission speed Camera Module + Wide Angle Lens: The camera module is based on the original high-quality camera of Raspberry Pi, which can provide higher resolution and higher sensitivity. With a 6mm wide-angle lens, it has better performance in visual fidelity. Raspberry Pi original high-quality camera features: 1. 12 million pixels 4056 (H) x 3040 (V), support RAW12 / 10 /8, COMP8 format output 2. 7.9mm CMOS diagonal length 3. C-mount/CS-mount lens standard with integrated IR filter Wide angle lens features: 1. 6mm Focal Length, 63 degree field angle, wider field of view 2. F1.2 Aperture, for more sufficient light entering, support manual adjustment The 4.3-inch IPS screen has the advantages of true color and large viewing angle. At the same time, the DSI display has a high frame rate and does not occupy the Raspberry Pi 40pin GPIO interface. The Raspberry Pi system has good compatibility and is an ideal match for this kit. 4.3-inch capacitive touch screen features: 1. 800 x 480 pixels IPS screen, combined with tempered glass panel, supports 5-points touch, and the visual angle can up to 160??° 2. Support DSI display interface, high frame rate, good compatibility with Raspberry Pi system Aluminum Alloy Bracket Large base for holding the object being viewed, free up and sown bracketPackage List1. PI4B-4GB x 1 2. Micro SD Card 16GB x 1 3. 4.3-inch DSI LCD x 1 4. 6mm Wide Angle Lens x 1 5. Microscope Bracket Kit x 1 6. Raspberry Pi HQ Camera x 1 7. Camera holder x 1 8. 5V 4A Type C US plug power supply x 1 9. 15Pin FFC ~30cm x 1 10. Screws pack x 1 11. Card reader x 1 12. Cooling fan x 1

Read more less

1. No backlight, keeps displaying last content for a long time even when power down 2. Ultra low power consumption, basically power is only required for refreshing 3. Come with development resources and manual(driver board schematic, examples for Raspberry Pi/Arduino/STM32) Specifications: 1. Operating voltage: 3.3V 2. Interface: 3-wire SPI, 4-wire SPI 3. Outline dimension: 99.5 x 79.5 x 0.85mm 4. Display size: 90.11 x 64.77mm 5. Dot pitch: 0.176 x 0.176mm 6. Resolution: 512 x 368 pixels 7. Display color: Red/Yellow/Black/White 8. Grey level: 2 9. Full refresh time: 14s 10. Refresh power: Less than 61.7mW (typ.) 11. Standby power: Less than 0.01uA (almost none) 12. Viewing angle: Greater than 170 degree

Read more less

1. Rated power: 3.3V/5V2. Interface: 3-wire SPI, 4-wire SPI3. Full refresh time: 3414. Refresh power: about 61.7mW5. Dot pitch: 0.176 × 0.176mm6. Standby current: about 0.01uA7. Without backlight, the last content can be displayed for a long time even if the power is cut off.8. Ultra-low power consumption, basically only need to refresh.9. SPI interface for connecting Raspberry Pi / Jetson Nano / Arduino / STM32 and other controller boards.10. On-board voltage converter, compatible with 3.3V/5V MCU.

Read more less

Overview1. The SIM7600A-H 4G HAT is a 4G communication and GNSS positioning module, which supports LTE CAT4 up to 150Mbps for downlink data transfer. it is pretty low power consumption. 2. You can connect this 4G module with computer to surf the Internet, or attach it onto Raspberry Pi to enable functions like 4G high speed connection, wireless communication, making telephone call, sending SMS, global positioning, etc.Applicable Region1. SIM7600A-H is mainly applicable in North America (US, CA, MX), SIM7600E-H is mainly applicable in Southeast Asia, West Asia, Europe, Africa, SIM7600CE-T is mainly applicable in China. 2. Please check the supported bands according to your local service provider, select the proper one when placing order.Features1. Raspberry Pi connectivity, compatible with Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+ 2. Support dial-up, telephone call, SMS, MMS, mail, TCP, UDP, DTMF, HTTP, FTP, etc. 3. Support GPS, BeiDou, Glonass, LBS base station positioning 4. Onboard USB interface, to test AT Commands, get GPS positioning data, and so on 5. Onboard CP2102 USB to UART converter, for serial debugging 6. Breakout UART control pins, to connect with host boards like Arduino/STM32 7. SIM card slot, supports 1.8V/3V SIM card 8. Onboard audio jack and audio decoder for making telephone call 9. 2x LED indicators, easy to monitor the working status 10. Onboard voltage translator, operating voltage can be configured to 3.3V or 5V via jumper 11. Baudrate: 300bps-4Mbps (default: 115200bps) 12. Autobauding baudrate: 9600bps-115200bps 13. Control via AT commands (3GPP TS 27.007, 27.005, and V.25TER command set) 14. Support SIM application toolkit: SAT Class 3, USAT 15. Come with development resources and manual (examples for Raspberry Pi/Arduino/STM32)Communications Specifications1. Band: A. LTE: - SIM7600A-H: LTE-FDD B2/B4/B12 - SIM7600E-H: LTE-FDD B1/B3/B5/B7/B8/B20, LTE-TDD B38/B40/B41 - SIM7600CE-T: LTE-TDD B38/B39/B40/B41, LTE-FDD B1/B3/B8 B. WCDMA / TD-SCDMA/ CDMA 2000 - SIM7600A-H: UMTS/HSPA+ B2/B5 - SIM7600E-H: UMTS/HSPA+ B1/B5/B8 - SIM7600CE-T: UMTS/HSDPA/HSPA+ B1/B8, TD-SCDMA B34/B39, CDMA 1X/EVDO BC0 C. GSM/GPRS/EDGE 900/1800 MHz 2. Generation: 4G, 3G, 2.5G, 2G 3. Emitting power: 0.25W, 0.5W/EGSM900, 0.4W/DCS1800, 2W/GSM900, 1W/DCS1800 4. Data Speed - LTE CAT 4: Uplink=<50 Mbps, Downlink=<150 Mbps - UMTS: Uplink=<384Kbps, Downlink=<384Kbps - EDGE: Uplink=<236.8kbps, Downlink=<236.8kbps - GPRS: Uplink=<85.6kbps, Downlink=<85.6kbps - HSPA+: Uplink=<5.76Mbps, Downlink=<42MbpsGNSS Specifications1. Receiver type - 16-channel - C/A code 2. Sensitivity - Tracking: -159 dBm (GPS) / -158 dBm (GLONASS) / TBD (BD) - Cold starts: -148 dBm 3. Time-To-First-Fix (open air) - Cold starts: <35s - Hot starts: <1s 4. Accuracy - Position: <2.5m CEPSMS and Audio Specifications1. SMS - Support types: MT, MO, CB, Text, PDU - Storage: USIM card and ME (default) 2. Audio feature - Support echo cancellation - Support noise reductionOther Specifications1. Power supply: 5V 2. Operating voltage: 5V/3.3V (configured via jumper) 3. Operating temperature: -30 degree C ~ 80 degree C 4. Storage temperature: -45 degree C - 90 degree C 5. Dimension: 56.21mm x 65.15mmWhat is on Board1. SIM7600CE-T 2. CP2102 USB to UART converter 3. NAU8810 audio decoder 4. TXS0108EPWR voltage translator: Translates 3.3V/5V into 1.8V 5. MP2128DT power chip 6. MP1482 power chip 7. Raspberry Pi GPIO header: For connecting with Raspberry Pi 8. SIM7600 control interface: For connecting with host boards like Arduino/STM32 9. SIM card slot: Supports 1.8V/3V SIM card 10. TF card slot: Allows file/SMS/...storage 11. 3.5mm earphone/mic jack 12. USB interface: For testing AT Commands, getting GPS positioning data, etc. 13. USB to UART interface: For serial debugging, or login to Raspberry Pi 14. MAIN antenna connector 15. AUX antenna connector 16. GNSS antenna connector 17. Power switch 18. Network status indicator 19. Power indicator 20. Operating voltage selection jumper: - VCCIO-3.3V: set operating voltage as 3.3V - VCCIO-5V: set operating voltage as 5V 21. UART selection jumper: - A: Access Raspberry Pi via USB to UART - B: Control the SIM7600 by Raspberry Pi - C: Control the SIM7600 via USB to UARTPackage List1. SIM7600CE 4G HAT x1 2. LTE Antenna x1 3. GPS External Antenna (B) x1 4. USB type A plug to micro plug cable x2 5. RPi screws pack (2pcs) x1

Read more less

4G/3G/GNSS HAT for Raspberry Pi, Based on SIM7600E-HApplicable Region1. SIM7600A-H is mainly applicable in North America (US, CA, MX), SIM7600E-H is mainly applicable in Southeast Asia, West Asia, Europe, Africa, SIM7600CE-T is mainly applicable in China.2. Please check the supported bands according to your local service provider, select the proper one when placing order.Overview1. The SIM7600A-H 4G HAT is a 4G communication and GNSS positioning module, which supports LTE CAT4 up to 150Mbps for downlink data transfer. it is pretty low power consumption.2. You can connect this 4G module with computer to surf the Internet, or attach it onto Raspberry Pi to enable functions like 4G high speed connection, wireless communication, making telephone call, sending SMS, global positioning, etc.Features1. Raspberry Pi connectivity, compatible with Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+2. Support dial-up, telephone call, SMS, MMS, mail, TCP, UDP, DTMF, HTTP, FTP, etc.3. Support GPS, BeiDou, Glonass, LBS base station positioning4. Onboard USB interface, to test AT Commands, get GPS positioning data, and so on5. Onboard CP2102 USB to UART converter, for serial debugging6. Breakout UART control pins, to connect with host boards like Arduino/STM327. SIM card slot, supports 1.8V/3V SIM card8. Onboard audio jack and audio decoder for making telephone call9. 2x LED indicators, easy to monitor the working status10. Onboard voltage translator, operating voltage can be configured to 3.3V or 5V via jumper11. Baudrate: 300bps ~ 4Mbps (default: 115200bps)12. Autobauding baudrate: 9600bps ~ 115200bps13. Control via AT commands (3GPP TS 27.007, 27.005, and V.25TER command set)14. Support SIM application toolkit: SAT Class 3, USAT15. Come with development resources and manual (examples for Raspberry Pi/Arduino/STM32)Communications Specifications1. Band: - LTE-- SIM7600A-H: --- LTE-FDD B2/B4/B12-- SIM7600E-H: --- LTE-FDD B1/B3/B5/B7/B8/B20--- LTE-TDD B38/B40/B41-- SIM7600CE-T: --- LTE-TDD B38/B39/B40/B41--- LTE-FDD B1/B3/B8- WCDMA / TD-SCDMA / CDMA 2000-- SIM7600A-H: --- UMTS/HSPA+ B2/B5-- SIM7600E-H: --- UMTS/HSPA+ B1/B5/B8-- SIM7600CE-T:--- UMTS/HSDPA/HSPA+ B1/B8--- TD-SCDMA B34/B39 --- CDMA 1X/EVDO BC0- GSM/GPRS/EDGE 900/1800 MHz2. Generation: 4G, 3G, 2.5G, 2G3. Emitting power: 0.25W, 0.5W@EGSM900, 0.4W@DCS1800, 2W@GSM900, 1W@DCS18004. Data Speed- LTE CAT 4-- Uplink=<50 Mbps-- Downlink=<150 Mbps- UMTS-- Uplink=<384Kbps-- Downlink=<384Kbps- EDGE-- Uplink=<236.8kbps-- Downlink=<236.8kbps- GPRS-- Uplink=<85.6kbps-- Downlink=<85.6kbps- HSPA+-- Uplink=<5.76Mbps-- Downlink=<42MbpsGNSS Specifications1. Receiver type- 16-channel- C/A code2. Sensitivity- Tracking: -159 dBm (GPS) / -158 dBm (GLONASS) / TBD (BD)- Cold starts: -148 dBm3. Time-To-First-Fix (open air)- Cold starts: <35s- Hot starts: <1s4. Accuracy- Position: <2.5m CEPSMS and Audio Specifications1. SMS- Support types: MT, MO, CB, Text, PDU- Storage: USIM card and ME (default)2. Audio feature- Support echo cancellation- Support noise reductionOther Specifications1. Power supply: 5V2. Operating voltage: 5V/3.3V (configured via jumper)3. Operating temperature: -30 degree C ~ 80 degree C4. Storage temperature: -45 degree C ~ 90 degree C5. Dimension: 56.21mm x 65.15mmWhat is on Board1. SIM7600E-H2. CP2102 USB to UART converter3. NAU8810 audio decoder4. TXS0108EPWR voltage translator: translates 3.3V/5V into 1.8V5. MP2128DT power chip6. MP1482 power chip7. Raspberry Pi GPIO header: for connecting with Raspberry Pi8. SIM7600 control interface: for connecting with host boards like Arduino/STM329. SIM card slot: supports 1.8V/3V SIM card10. TF card slot: allows file/SMS/... storage11. 3.5mm earphone/mic jack12. USB interface: for testing AT Commands, getting GPS positioning data, etc.13. USB to UART interface: for serial debugging, or login to Raspberry Pi14. MAIN antenna connector15. AUX antenna connector16. GNSS antenna connector17. Power switch18. Network status indicator19. Power indicator20. Operating voltage selection jumper: - VCCIO - 3.3V: set operating voltage as 3.3V- VCCIO - 5V: set operating voltage as 5V21. UART selection jumper: - A: Access Raspberry Pi via USB to UART- B: Control the SIM7600 by Raspberry Pi- C: Control the SIM7600 via USB to UARTPackage Contents1. SIM7600E-H 4G HAT x12. LTE Antenna x13. GPS External Antenna (B) x14. USB type A plug to micro plug cable x25. RPi screws pack (2pcs) x1

Read more less

4G/3G/GNSS HAT for Raspberry Pi, Based on SIM7600A-HApplicable Region1. SIM7600A-H is mainly applicable in North America (US, CA, MX), SIM7600E-H is mainly applicable in Southeast Asia, West Asia, Europe, Africa, SIM7600CE-T is mainly applicable in China.2. Please check the supported bands according to your local service provider, select the proper one when placing order.Overview1. The SIM7600A-H 4G HAT is a 4G communication and GNSS positioning module, which supports LTE CAT4 up to 150Mbps for downlink data transfer. it is pretty low power consumption.2. You can connect this 4G module with computer to surf the Internet, or attach it onto Raspberry Pi to enable functions like 4G high speed connection, wireless communication, making telephone call, sending SMS, global positioning, etc.Features1. Raspberry Pi connectivity, compatible with Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+2. Support dial-up, telephone call, SMS, MMS, mail, TCP, UDP, DTMF, HTTP, FTP, etc.3. Support GPS, BeiDou, Glonass, LBS base station positioning4. Onboard USB interface, to test AT Commands, get GPS positioning data, and so on5. Onboard CP2102 USB to UART converter, for serial debugging6. Breakout UART control pins, to connect with host boards like Arduino/STM327. SIM card slot, supports 1.8V/3V SIM card8. Onboard audio jack and audio decoder for making telephone call9. 2x LED indicators, easy to monitor the working status10. Onboard voltage translator, operating voltage can be configured to 3.3V or 5V via jumper11. Baudrate: 300bps ~ 4Mbps (default: 115200bps)12. Autobauding baudrate: 9600bps ~ 115200bps13. Control via AT commands (3GPP TS 27.007, 27.005, and V.25TER command set)14. Support SIM application toolkit: SAT Class 3, USAT15. Come with development resources and manual (examples for Raspberry Pi/Arduino/STM32)Communications Specifications1. Band: - LTE-- SIM7600A-H: --- LTE-FDD B2/B4/B12-- SIM7600E-H: --- LTE-FDD B1/B3/B5/B7/B8/B20--- LTE-TDD B38/B40/B41-- SIM7600CE-T: --- LTE-TDD B38/B39/B40/B41--- LTE-FDD B1/B3/B8- WCDMA / TD-SCDMA / CDMA 2000-- SIM7600A-H: --- UMTS/HSPA+ B2/B5-- SIM7600E-H: --- UMTS/HSPA+ B1/B5/B8-- SIM7600CE-T:--- UMTS/HSDPA/HSPA+ B1/B8--- TD-SCDMA B34/B39 --- CDMA 1X/EVDO BC0- GSM/GPRS/EDGE 900/1800 MHz2. Generation: 4G, 3G, 2.5G, 2G3. Emitting power: 0.25W, 0.5W@EGSM900, 0.4W@DCS1800, 2W@GSM900, 1W@DCS18004. Data Speed- LTE CAT 4-- Uplink=<50 Mbps-- Downlink=<150 Mbps- UMTS-- Uplink=<384Kbps-- Downlink=<384Kbps- EDGE-- Uplink=<236.8kbps-- Downlink=<236.8kbps- GPRS-- Uplink=<85.6kbps-- Downlink=<85.6kbps- HSPA+-- Uplink=<5.76Mbps-- Downlink=<42MbpsGNSS Specifications1. Receiver type- 16-channel- C/A code2. Sensitivity- Tracking: -159 dBm (GPS) / -158 dBm (GLONASS) / TBD (BD)- Cold starts: -148 dBm3. Time-To-First-Fix (open air)- Cold starts: <35s- Hot starts: <1s4. Accuracy- Position: <2.5m CEPSMS and Audio Specifications1. SMS- Support types: MT, MO, CB, Text, PDU- Storage: USIM card and ME (default)2. Audio feature- Support echo cancellation- Support noise reductionOther Specifications1. Power supply: 5V2. Operating voltage: 5V/3.3V (configured via jumper)3. Operating temperature: -30 degree C ~ 80 degree C4. Storage temperature: -45 degree C ~ 90 degree C5. Dimension: 56.21mm x 65.15mmWhat is on Board1. SIM7600A-H2. CP2102 USB to UART converter3. NAU8810 audio decoder4. TXS0108EPWR voltage translator: translates 3.3V/5V into 1.8V5. MP2128DT power chip6. MP1482 power chip7. Raspberry Pi GPIO header: for connecting with Raspberry Pi8. SIM7600 control interface: for connecting with host boards like Arduino/STM329. SIM card slot: supports 1.8V/3V SIM card10. 3.5mm earphone/mic jack11. USB interface: for testing AT Commands, getting GPS positioning data, etc.12. USB to UART interface: for serial debugging, or login to Raspberry Pi13. MAIN antenna connector14. AUX antenna connector15. GNSS antenna connector16. Power switch17. Network status indicator18. Power indicator19. Operating voltage selection jumper: - VCCIO - 3.3V: set operating voltage as 3.3V- VCCIO - 5V: set operating voltage as 5V20. UART selection jumper: - A: access Raspberry Pi via USB to UART- B: control the SIM7600 by Raspberry Pi- C: control the SIM7600 via USB to UARTPackage Contents1. SIM7600A-H 4G HAT x12. LTE Antenna x13. GPS External Antenna (B) x14. USB type A plug to micro plug cable x25. RPi screws pack (2pcs) x1

Read more less

Features1. 5inch IPS capacitive touch screen, 800 x 480 resolution 2. Compatible with Raspberry Pi 4B/3B+/3A+/3B/2B/B+/A+, CM3/3+/4 (CM3/3+/4 requires extra adapter board) 3. The LCD is directly driven by Raspberry Pi DPI interface 4. Backlight can be turned off to lower power consumption 5. Toughened glass capacitive touch panel, 5-points touch 6. Compact size, suit for various projectsDevice & System Support1. Support Raspberry Pi OS, 5-points touch, driver free 2. Support Ubuntu / Kali / WIN10 IoT, single point touch, driver free 3. Support Retropie, driver freePackage List1. 5 inch DSI LCD (B) x 1 2. FPC 15PIN 1.0 pitch 50mm (opposite sides) x 1 3. Screws pack x 1

Read more less

1. Resolution: 800 x 4802. Display interface: DSI3. Display panel: IPS4. Viewing angle: 160 degrees5. Touch screen models:- Touch type: capacitive touch- Touch points: 5 points touch- Touch interface: I2C- Touch panel: tempered glass panel6. Application scenarios: smart home, automotive equipment, consumer electronics, industrial equipment, etc.7. Screen size: about 5 inch8. Size: no touch model about 12 x 7.58 x 0.51cm, touch model about 12.77 x 8.7 x 0.7cmFeatures:1. IPS display panel with good display performance and wide viewing angle of up to 160 degrees2. Integrated structure design, DSI one-line, easy to integrate integrated design, provide secondary development materials, help simple development3. Thinner and more space-saving, the driver circuit is integrated into the FPC, about 5mm thickness space can be4. Touch models capacitive five-point touch, flexible operation, through the I2C signal, lead to touch function, support five-point touch5. Touch model backlight brightness can be adjusted by software6. Support Raspberry Pi OS, 5-point touch, driver-free7. Support Ubuntu / Kali / WIN10 IoT, single-touch, driver-free8. Support Retropie, driver-free9. Support Pi 4B/3B+/3A+/3B/2B/B+/A+, some CM3/3+/4 backplanes need to buy adapter cable separately

Read more less

1. Resolution: 800 x 4802. Display interface: DSI3. Display panel: IPS4. Viewing angle: 160 degrees5. Touch screen models:- Touch type: capacitive touch- Touch points: 5 points touch- Touch interface: I2C- Touch panel: tempered glass panel6. Application scenarios: smart home, automotive equipment, consumer electronics, industrial equipment, etc.7. Screen size: about 5 inch8. Size: no touch model about 12 x 7.58 x 0.51cm, touch model about 12.77 x 8.7 x 0.7cmFeatures:1. IPS display panel with good display performance and wide viewing angle of up to 160 degrees2. Integrated structure design, DSI one-line, easy to integrate integrated design, provide secondary development materials, help simple development3. Thinner and more space-saving, the driver circuit is integrated into the FPC, about 5mm thickness space can be4. Touch models capacitive five-point touch, flexible operation, through the I2C signal, lead to touch function, support five-point touch5. Touch model backlight brightness can be adjusted by software6. Support Raspberry Pi OS, 5-point touch, driver-free7. Support Ubuntu / Kali / WIN10 IoT, single-touch, driver-free8. Support Retropie, driver-free9. Support Pi 4B/3B+/3A+/3B/2B/B+/A+, some CM3/3+/4 backplanes need to buy adapter cable separately

Read more less

1. 800 x 480 high resolution,Resistive touch control 2. Supports Raspberry Pi 3. Supports popular mini-PCs like Raspberry Pi, BB Black, etc. 4. Not only for mini-PCs, it can work as a computer monitor just like any other general HDMI screen 5. Backlight can be turned off to lower power consumption

Read more less

1. 800x480 hardware resolution, configurable by software (up to 1920x1080) 2. Supports popular mini PCs such as Raspberry Pi, BB Black, Banana Pi, as well as general desktop computers - When works with Raspberry Pi, supports Raspbian, Ubuntu, WIN10 IOT, single touch, and driver free - When work as a computer monitor, supports Windows 10/8.1/8/7, single touch, and driver free 3. Supports popular game consoles like Microsoft XBOX360, Sony PS4, and Nintendo Switch, etc. 4. Multi languages OSD menu, for power management, brightness/contrast adjustment, etc. 5. 3.5mm audio jack, speaker connector, supports HDMI audio output 6. Also supports VGA input (specific cable is required and should be purchased separately)

Read more less

1. 800x480 hardware resolution, configurable by software (up to 1920x1080) 2. Supports popular mini PCs such as Raspberry Pi, BB Black, Banana Pi, as well as general desktop computers - When works with Raspberry Pi, supports Raspbian, Ubuntu, WIN10 IOT, single touch, and driver free - When work as a computer monitor, supports Windows 10/8.1/8/7, single touch, and driver free 3. Supports popular game consoles like Microsoft XBOX360, Sony PS4, and Nintendo Switch, etc. 4. Multi languages OSD menu, for power management, brightness/contrast adjustment, etc. 5. 3.5mm audio jack, speaker connector, supports HDMI audio output 6. Also supports VGA input (specific cable is required and should be purchased separately)

Read more less

1. 800x480 hardware resolution, configurable by software (up to 1920x1080)2. Supports popular mini PCs such as Raspberry Pi, BB Black, Banana Pi, as well as general desktop computers - When works with Raspberry Pi, supports Raspbian, Ubuntu, WIN10 IOT, single touch, and driver free - When work as a computer monitor, supports Windows 10/8.1/8/7, single touch, and driver free3. Supports popular game consoles like Microsoft XBOX360, Sony PS4, and Nintendo Switch, etc.4. Multi languages OSD menu, for power management, brightness/contrast adjustment, etc.5. 3.5mm audio jack, speaker connector, supports HDMI audio output6. Also supports VGA input (specific cable is required and should be purchased separately)

Read more less

1. 800 x 480 high resolution,Resistive touch control 2. Compatible and Direct-connect with any revision of Raspberry Pi (except the Pi 1 model B or Pi Zero, which requires an HDMI cable) 3. Drivers provided (works with your own Raspbian/Ubuntu directly) 4. HDMI interface for displaying, no I/Os required (however, the touch panel still needs I/Os) 5. Backlight can be turned off to lower power consumption 6. High quality immersion gold surface plating

Read more less

Device & System SupportRaspberry Pi 1. Support Raspbian, 5-points touch, driver free 2. Support Ubuntu / Kali / WIN10 IoT, single point touch, driver free 3. Support Retropie, driver free 4. Support all versions of Raspberry Pi PC Support Windows 10 / 8.1 / 8 / 7, 5-points touch, driverTouch Control1. Up to 5-points touch, depending on the operating system. 2. Up to 6H hardness toughened glass panel.Package List1. 5 inch HDMI LCD (H) V4 x1 2. HDMI cable x1 3. HDMI to Micro HDMI Adapter x1 4. USB type A plug to micro B plug cable x1 5. RPi screws pack (4pcs) x1

Read more less

About The ProductI am a Raspberry Pi CM4 kit with a 5 inch touch screen all-in-one machine. The PoE pin Gigabit Ethernet port supports 4K output, onboard four-way USB2.0, 5-inch touch screen, etc. The all-in-one kit is convenient for users. Notes: 1. Do not plug and unplug any device except USB and HDMI while the baseboard is working. 2. If the fan needs to be replaced, please confirm the fan voltage and then power on. 3. The USB SLAVE interface is used to burn the image and cannot be used as an OTG interface. 4. In normal use, it is necessary to provide at least 5V 2.5A power supply for CM4. Otherwise, there may be problems such as automatic shutdown, frequency reduction and so on. 5. Onboard default 4-way USB 2.0 interface. 6. Support POE pins, additional POE HAT is required if POE function is required. 7. This screen needs to add a driver to work.Specifications1. CM4 Socket: Suitable for all variants of Compute Module 4 2. Networking: - Gigabit Ethernet RJ45 connector - M.2 M KEY, supports NVME SSD 3. POE: PoE header (additional PoE HAT is required to enable PoE feature) 4. USB: USB 2.0 x 4 5. Display: 5 inch screen, 800 x 480 pixels, 5-point capacitive touch 6. Camera: MIPI CSI-2 port x 2 (15pin 1.0mm FPC connector) 7. Video: HDMI, supports 4K 30fps output 8. RTC: Real-time clock with battery socket and ability to wake Compute Module 4 9. Storage: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 10. Fan header: Allows speed adjustment and measurement, 5V / 12V 11. Power input: 5V 12. Size: 127.7 x 87.45mm

Read more less

Features1. 5inch IPS screen, 800x480 hardware resolution2. Compatible with Raspberry Pi 2B/3B/3B+/3A+/Zero/Zero W/Zero WH3. The LCD is directly driven by Raspberry Pi DPI interface, refresh rate up to 60Hz4. Supports Raspbian, Ubuntu, OSMC, etc.5. Backlight can be turned off to lower power consumption6. Compact size, suit for various projectsNote: This item can be used for displaying ONLY, if touch panel is required, please consider 5inch HDMI Capacitive Touch LCD OR 5inch HDMI Resistive Touch LCD.Package Contents1. 5inch 800×480 IPS LCD x12. RGB LCD HAT (B) x13. LCD stand (small size) x1

Read more less

OverviewThis is a 5.5inch AMOLED display. Compared with LCD, it has advantages of high contrast, wide color gamut, and wide viewing angle, which make it able to bring vivid and delicate visual experience.Features1. 5.5 inch AMOLED, 1080x1920 resolution2. Toughened glass capacitive touch panel, 6H hardness3. Support popular mini PCs such as Raspberry Pi, Jetson Nano, as well as general desktop computers4. When works with Raspberry Pi, supports Raspbian / Ubuntu / Kali / Retropie, driver free5. When works as a computer monitor, support Windows 10/8.1/8/7, five-points touch, and driver free6. 3.5mm audio jack, supports HDMI audio output7. M2.5 screw holes for easy mountingPackage Contents1. 5.5inch HDMI AMOLED x12. HDMI cable x13. USB type A plug to micro B plug cable x14. HDMI adapter (B) x15. USB adapter (B) x16. Screws pack x1

Read more less

Features1. 5.5-inch IPS display with a hardware resolution of 1440 ?? 2560 2. 10-point capacitive touch control with toughened glass panel, hardness up to 6H 3. Adopt the optical bonding touch technique for better use 4. Support Raspberry Pi OS / Ubuntu / Kali and Retropie when working with Raspberry Pi 4B 5. Support Windows 11/10/8.1/8/7 when working as a computer monitor 6. Support HDMI audio output with 3.5mm Jack and 4PIN headerDevice & System Support1. For the moment, only the Raspberry Pi 4B and CM4 have adequate CPU performance to drive this 2K display completely. 2. Support more powerful future versions as long as its GPU performance is equivalent to or better than the Pi 4B. 3. Limited by the hardware, when working with Raspberry Pi 3B+/Pi 3B/Zero 2w/Zero w, only supports default portrait display and cannot be rotated. 4. The case only supports Raspberry Pi 4B.Package List1. 5.5 inch 1440x2560 LCD x1 2. HDMI cable x1 3. USB type A plug to micro B plug cable x1 4. USB adapter (B) x1 5. HDMI adapter (B) x1 6. HDMI to Micro HDMI adapter (C) x1 7. USB adapter (D) x1 8. Screws pack x1

Read more less

Overview1. This is an E-Ink display HAT for Raspberry Pi, 5.83 inch, 600x448 resolution, with embedded controller, communicating via SPI interface, supports red, black, and white three-color display.2. Due to the advantages like ultra low power consumption, wide viewing angle, clear display without electricity, it is an ideal choice for applications such as shelf label, industrial instrument, and so on.Features1. No backlight, keeps displaying last content for a long time even when power down2. Ultra low power consumption, basically power is only required for refreshing3. Compatible with Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+, Jetson Nano4. SPI interface, for connecting with other controller boards like Raspberry/Arduino/Nucleo, etc.5. Comes with development resources and manual (examples for Raspberry Pi/Jetson Nano/Arduino/STM32)Specifications1. Operating voltage: 3.3V~5V2. Interface: SPI3. Outline dimension: 125.40mm x 99.50mm4. Display size: 118.80mm x 88.26mm5. Dot pitch: 0.198 x 0.1976. Resolution: 600 x 4487. Display color: Red, black, white8. Grey level: 29. Full refresh time: 14s10. Refresh power: 26.4mW(typ.)11. Standby power: <0.017mW12. Viewing angle: >170 degreePackage Contents1.5.83 inch e-Paper (B) x12. e-Paper Driver HAT x13. RPi screws pack (2pcs) x14. PH2.0 20cm 8Pin x1

Read more less

Features1. No backlight, keeps displaying last content for a long time even when power down 2. Ultra low power consumption, basically power is only required for refreshing 3. SPI interface, requires minimal IO pins 4. 2x user buttons and 1x reset button for easy interacting 5. Comes with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples)Specification1. Operating voltage: 3.3V 2. Display color: Black, white 3. Resolution: 648x480 pixels 4. Grey scale: 2 5. Interface: 3-wire SPI, 4-wire SPI 6. Viewing angle: Greater than 170 degree 7. Partial refresh time: N/A 8. Full refresh time: 5s 9. Dimensions: 125.4x99.5mm 10. Display size: 119.232x88.320mm 11. Refresh power: 26.4mW (typ.) 12. Standby current: Less than 0.01uA (almost none) 13. Dot pitch: 0.184 x 0.184mmAdvantages Of EINK1. E-paper display utilizes microcapsule electrophoretic technology for displaying, the principle is: charged particles suspended in clear fluid will move to sides of microcapsule when electric field is applied, making the microcapsule become visible by reflecting ambient light, just as traditional printed paper. 2. E-paper display will clearly display images/texts under lamplight or natural light, requires no backlight, and features nearly up to 180 degree viewing angle. It is usually used as e-reader due to its paper-like effect.Package List1. 5.83 inch e-Paper x 1 2. Pico-ePaper-Driver-Board x 1 3. Standoff pack x 1

Read more less

Features1. No backlight, keeps displaying last content for a long time even when power down 2. Ultra low power consumption, basically power is only required for refreshing 3. SPI interface, requires minimal IO pins 4. 2x user buttons and 1x reset button for easy interacting 5. Comes with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples)Specification1. Operating voltage: 3.3V 2. Display color: Red, black, white 3. Resolution: 648x480 pixels 4. Grey scale: 2 5. Interface: 3-wire SPI, 4-wire SPI 6. Viewing angle: Greater than 170 degree 7. Partial refresh time: N/A 8. Full refresh time: 5s 9. Dimensions: 125.4x99.5mm 10. Display size: 119.232x88.320mm 11. Refresh power: 26.4mW (typ.) 12. Standby current: Less than 0.01uA (almost none) 13. Dot pitch: 0.184 x 0.184mmAdvantages Of EINK1. E-paper display utilizes microcapsule electrophoretic technology for displaying, the principle is: charged particles suspended in clear fluid will move to sides of microcapsule when electric field is applied, making the microcapsule become visible by reflecting ambient light, just as traditional printed paper. 2. E-paper display will clearly display images/texts under lamplight or natural light, requires no backlight, and features nearly up to 180 degree viewing angle. It is usually used as e-reader due to its paper-like effect.Package List1. 5.83 inch e-Paper x 1 2. Pico-ePaper-Driver-Board x 1 3. Standoff pack x 1

Read more less

This is a MIPI_CSI camera with 5MP and 70 degree FOV. The onboard optical image stabilization camera module supports dual-axis image stabilization+/-5 degree compensation angle. Suitable for motion cameras, robots, wearables, and so on. Support Raspberry Pi, and Sunrise X3 Pi. Specifications: 1.Sensor :OV5647 2. CMOS Size: 1/4 inch 3. Pixel: 5MP 4. Aperture: F 2.8 5. Focal Length: 3.2mm 6. Angle of View: 70 degrees 7. Stabilization Type: OIS (Optical Image Stabilization) Stabilization 8. Focusing: Fixed focus 9. Distortion: Less than 1.0% 10. Range: XY axis +/- 5 derees 11. Image: 2592 x 1944 still image resolution 12. Video recording: 1920 x 1080p 30fps, 1280 x 720p 60fps, 640 ?? 480p 60fps, 640 x 480p 90fps

Read more less

600x448, 5.83inch E-Ink raw display, SPI interface, without PCBOverview1. This is an E-Ink raw display, 5.83inch, 600x448 resolution, with embedded controller, communicating via SPI interface.2. Due to the advantages like ultra low power consumption, wide viewing angle, clear display without electricity, it is an ideal choice for applications such as shelf label, industrial instrument, and so on.Features1. No backlight, keeps displaying last content for a long time even when power down2. Ultra low power consumption, basically power is only required for refreshing3. Comes with development resources and manual (driver board schematic, examples for Raspberry Pi/Arduino/STM32)Specifications1. Operating voltage: 3.3V2. Interface: 3-wire SPI, 4-wire SPI3. Outline dimension: 125.40mm x 99.50mm x 1.18mm4. Display size: 118.80mm x 88.26mm5. Dot pitch: 0.198 x 0.1976. Resolution: 600 x 4487. Display color: black, white8. Grey level: 29. Full refresh time: 3.5s10. Refresh power: 26.4mW(typ.)11. Standby power: <0.017mW12. Viewing angle: >170 degree

Read more less

1. 160x80 resolution, IPS screen, 65K RGB colors, clear and colorful displaying effect 2. SPI interface, requires minimal IO pins 3. 1x joystick and 2x user buttons for easy interacting 4. Comes with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples) Specification 1. Operating voltage: 2.6 ~ 5.5V 2. Resolution: 160x80 pixels 3. Display color: 65K RGB 4. Communication interface: 4-wire SPI 5. Display panel: IPS 6. Display size: 21.70 x 10.80mm 7. Pixel size: 0.1356 x 0.135mm 8. Driver: ST7735S 9. Size: 52.00 x 25.00mm

Read more less

Device & System SupportSuitable for Raspberry Pi: 1. Support Raspberry Pi OS, 5-points touch, driver free 2. Support Ubuntu, single point touch, driver free 3. Support Pi 4BSpecifications1. Sensor: OV5647 2. CMOS size: 1/4 inch 3. Pixels: 5MP 4. Aperture: F2.4 5. Focal length: 3.89mm 6. Diagonal FOV: 72.9 degrees 7. Distortion: Less than 1.5% 8. Depth of field: 20cm above 9. Image: 2592 x 1944 still image resolution 10. Video: 1920 x 1080p 30fps, 1280 x 720p 60fps, 640 x 480p 60fps, 640 x 480p 90fpsPackage List1. 7 inch DSI LCD (with cam) kit x1 2. Black case kit x1

Read more less

Device & System SupportSuitable for Raspberry Pi: 1. Support Raspberry Pi OS, 5-points touch, driver free 2. Support Ubuntu, single point touch, driver free 3. Support Pi 4BSpecifications1. Sensor: OV5647 2. CMOS size: 1/4 inch 3. Pixels: 5MP 4. Aperture: F2.4 5. Focal length: 3.89mm 6. Diagonal FOV: 72.9 degrees 7. Distortion: Less than 1.5% 8. Depth of field: 20cm above 9. Image: 2592 x 1944 still image resolution 10. Video: 1920 x 1080p 30fps, 1280 x 720p 60fps, 640 x 480p 60fps, 640 x 480p 90fpsPackage List1. 7 inch DSI LCD x 1 2. FPC 15 PIN 1.0 pitch 50mm (opposite sides) x 2 3. FPC 15 PIN 1.0 pitch 120mm (opposite sides) x 1 4. 2 PIN wire 10cm x 1 5. Screws pack x 1

Read more less

1. IPS LCD screen, more natural gradient colors and more vivid display colors2. 170-degree wide viewing angle, excellent display performance3. High-quality picture, clear and bright4. The screen has more color details and a better visual experience5. Support capacitive 5-point touch6. Support adjusting brightness through software7. Display size: 7 inches8. Product size: 192.96 x 110.8mm9. Weight: 246g, 375gPacking list:-7 inch DSI LCD (B) x1-FPC 15PIN 1.0 pitch 50mm (opposite sides) x1-2PIN to PH2.0 2PIN cable 6cm x1-FPC 15PIN 1.0 pitch 160mm (opposite sides) x1-Screw pack x1

Read more less

1. IPS LCD screen, more natural gradient colors and more vivid display colors2. 170-degree wide viewing angle, excellent display performance3. High-quality picture, clear and bright4. The screen has more color details and a better visual experience5. Support capacitive 5-point touch6. Support adjusting brightness through software7. Display size: 7 inches8. Product size: 192.96 x 110.8mm9. Weight: 246g, 375gPacking list:-7 inch DSI LCD (B) x1-FPC 15PIN 1.0 pitch 50mm (opposite sides) x1-2PIN to PH2.0 2PIN cable 6cm x1-FPC 15PIN 1.0 pitch 160mm (opposite sides) x1-Screw pack x1

Read more less