STLINK-V3SET, Modular Debugger / Programmer For STM32 / STM8

STLINK-V3SET, modular in-circuit debugger and programmer for STM32/STM8

Description
1. The STLINK-V3SET is a modular stand-alone debugging and programming probe for the STM8 and STM32 microcontrollers. It is composed of a main module and a complementary adapter board.
2. The SWIM and JTAG/SWD interfaces are used to communicate with any STM8 or STM32 microcontroller located on an application board.
3. The STLINK-V3SET also provides a Virtual COM port interface allowing the host PC to communicate with the target microcontroller through one UART, and bridge interfaces (SPI, I2C, CAN, GPIOs) allowing for instance the programming of the target through bootloader.
4. The modular architecture of STLINK-V3SET enables to extend its main features through additional modules such as the adapter board.

Key Features
1. Stand-alone probe with modular extensions
2. Self-powered through a Micro-B USB connector (does not provide power supply to the target application)
3. USB 2.0 high-speed compatible interface
4. Direct firmware update (DFU) support, to use with more future devices
- JTAG / serial wire debugging (SWD) specific features:
- 3V to 3.6 V application voltage support and 5 V tolerant inputs
- Flat cables STDC14 to MIPI10 / STDC14 / MIPI20 (connectors with 1.27 mm pitch)
- Flat cable for 20-pin JTAG/SWD (2.54 mm pitch) (extra free cable from Waveshare)
- SWD and serial wire viewer (SWV) communication support
5. SWIM specific features (only available with adapter board MB1440):
- 1.65 V to 5.5 V application voltage support
- SWIM header (2.54 mm pitch)
- SWIM cables with dual 4-pin connectors / 4-pin connector to separated pins (2.54 mm pitch) (extra free cables from Waveshare)
- SWIM low-speed and high-speed modes support
6. Virtual COM port (VCP) specific features:
- 3 V to 3.6 V application voltage support on the UART interface and 5 V tolerant inputs
- VCP frequency up to 15 MHz
- Available on STDC14 debug connector (not available on MIPI10)
7. Multi-path bridge USB to SPI/UART/I2C/CAN/GPIOs specific features:
- 3 V to 3.6 V application voltage support and 5 V tolerant inputs
- Signals available on adapter board only (MB1440)
8. Drag-and-drop Flash programming
9. Two color LEDs: communication, power

Supported Software
1. STM32CubeProgrammer
2. KEIL RVMDK
3. IAR EWARM
4. GCC-based IDEs

Supported Devices
1. All STM8 MCUs with SWIM interface
2. All STM32 MCUs with JTAG / SWD interface

Package Contents
1. STLINK-V3SET x1
2. USB type A plug to micro B plug cable x1
3. 20-pin JTAG/SWD flat ribbon (extra free) x1
4. SWIM dual 4-pin connectors cable (extra free) x1
5. SWIM 4-pin connector to separated pins cable (extra free) x1


Specification:
Package Weight
One Package Weight 0.25kgs / 0.56lb
One Package Size 16cm * 9cm * 5cm / 6.3inch * 3.54inch * 1.97inch
Qty per Carton 96
Carton Weight 15.00kgs / 33.07lb
Carton Size 48cm * 36cm * 40cm / 18.9inch * 14.17inch * 15.75inch
Loading Container 20GP: 385 cartons * 96 pcs = 36960 pcs
40HQ: 895 cartons * 96 pcs = 85920 pcs

STLINK-V3SET, Modular Debugger / Programmer For STM32 / STM8

Product form

SKU: ZY14347413

  • In stock (Processing Time 1 - 72 hours)

€132,35

    • Guaranteed secure & safe checkout.

    Icon for truckShipping Methods

    To find out all available shipping methods, and the exact delivery time add the product to the cart and verify it using our shipping calculator.

    Icon for 24_hour_clockOrder Processing Time

    All orders are shipped within a maximum of 72 hours from the order's arrival.

    Icon for coinMoney Back Guarantee

    Garmade Money Back Guarantee- Get the item you ordered or your money back, it's that simple.

    Icon for image_placeholderMismatched Product

    Product doesn't match the description? Contact us within 31 days after you receive it!

    Icon for mobile_paymentRefunds

    In case of cancellation, money will be refunded to your account within 14 days.

    Description

    STLINK-V3SET, modular in-circuit debugger and programmer for STM32/STM8

    Description
    1. The STLINK-V3SET is a modular stand-alone debugging and programming probe for the STM8 and STM32 microcontrollers. It is composed of a main module and a complementary adapter board.
    2. The SWIM and JTAG/SWD interfaces are used to communicate with any STM8 or STM32 microcontroller located on an application board.
    3. The STLINK-V3SET also provides a Virtual COM port interface allowing the host PC to communicate with the target microcontroller through one UART, and bridge interfaces (SPI, I2C, CAN, GPIOs) allowing for instance the programming of the target through bootloader.
    4. The modular architecture of STLINK-V3SET enables to extend its main features through additional modules such as the adapter board.

    Key Features
    1. Stand-alone probe with modular extensions
    2. Self-powered through a Micro-B USB connector (does not provide power supply to the target application)
    3. USB 2.0 high-speed compatible interface
    4. Direct firmware update (DFU) support, to use with more future devices
    - JTAG / serial wire debugging (SWD) specific features:
    - 3V to 3.6 V application voltage support and 5 V tolerant inputs
    - Flat cables STDC14 to MIPI10 / STDC14 / MIPI20 (connectors with 1.27 mm pitch)
    - Flat cable for 20-pin JTAG/SWD (2.54 mm pitch) (extra free cable from Waveshare)
    - SWD and serial wire viewer (SWV) communication support
    5. SWIM specific features (only available with adapter board MB1440):
    - 1.65 V to 5.5 V application voltage support
    - SWIM header (2.54 mm pitch)
    - SWIM cables with dual 4-pin connectors / 4-pin connector to separated pins (2.54 mm pitch) (extra free cables from Waveshare)
    - SWIM low-speed and high-speed modes support
    6. Virtual COM port (VCP) specific features:
    - 3 V to 3.6 V application voltage support on the UART interface and 5 V tolerant inputs
    - VCP frequency up to 15 MHz
    - Available on STDC14 debug connector (not available on MIPI10)
    7. Multi-path bridge USB to SPI/UART/I2C/CAN/GPIOs specific features:
    - 3 V to 3.6 V application voltage support and 5 V tolerant inputs
    - Signals available on adapter board only (MB1440)
    8. Drag-and-drop Flash programming
    9. Two color LEDs: communication, power

    Supported Software
    1. STM32CubeProgrammer
    2. KEIL RVMDK
    3. IAR EWARM
    4. GCC-based IDEs

    Supported Devices
    1. All STM8 MCUs with SWIM interface
    2. All STM32 MCUs with JTAG / SWD interface

    Package Contents
    1. STLINK-V3SET x1
    2. USB type A plug to micro B plug cable x1
    3. 20-pin JTAG/SWD flat ribbon (extra free) x1
    4. SWIM dual 4-pin connectors cable (extra free) x1
    5. SWIM 4-pin connector to separated pins cable (extra free) x1


    Specification:
    Package Weight
    One Package Weight 0.25kgs / 0.56lb
    One Package Size 16cm * 9cm * 5cm / 6.3inch * 3.54inch * 1.97inch
    Qty per Carton 96
    Carton Weight 15.00kgs / 33.07lb
    Carton Size 48cm * 36cm * 40cm / 18.9inch * 14.17inch * 15.75inch
    Loading Container 20GP: 385 cartons * 96 pcs = 36960 pcs
    40HQ: 895 cartons * 96 pcs = 85920 pcs

    Additional Information

    Icon for truckShipping Info

    IMPORTANT INFO - PLEASE CHECK BEFORE ORDERING.



      Estimated transit time and postage fee depends on the method you choose at checkout. Please add the desired product to the cart and there you will be able to see all this information.

      Complete and right address is the guarantee of fast and efficient delivery, so please kindly recheck it when you place an order.

      In order to ensure a fast and efficient delivery, we need to have the method of contact with you. Email and Phone Number is a very important detail and must be accurate. All orders with an incorrect email or phone number will be canceled immediately.

      We strive to dispatch all orders within 72 hours of placing your order. But sometimes if the order is big or the products are more sophisticated, it can take a little longer. As soon as we dispatched it, you will receive a confirmation email along with a tracking number.

      Please be aware that sometimes due to unclear address, hard to access, no answer at address, the package can be kept at your local post office for collection. In this case you will be informed by the delivery company and by us. Please also monitor the tracking number.

      For European Union Countries:
    - If your order is less than 150€ excluding shipping costs, then the Taxes are already included in the price. This means that there will be NO extra charge upon delivery.
    - If your order is more than 150€, you will NOT be charged Taxes at the checkout, and you will have to pay upon delivery based on your local VAT rate.

     

    Icon for reviewReviews

    Customer Reviews

    Be the first to write a review
    0%
    (0)
    0%
    (0)
    0%
    (0)
    0%
    (0)
    0%
    (0)

    Login

    Forgot your password?

    Don't have an account yet?
    Create account