Waveshare Core407V, STM32F4 Core Board

Description

Overview
1. Core407V is a small STM32 development board that features an STM32F407VET6 device as the microcontroller, supports further expansion. It is ideal for starting application development with STM32F family.
2. As a minimal ready-to-run system, the Core407V integrates USB communication interface, JTAG/SWD programming/debugging interface, clock circuit, USB power management, boot mode selection, and so on.
3. Furthermore, pin headers on the backside allow the Core407V to be plugged-in your application board and act as the MCU core circuit in your system. All the I/O ports are accessible on the pin headers, and the header pitch is designed as 2.54mm.

What has On Board
1. STM32F407VET6: The high performance STM32 MCU which features:
- Core: Cortex-M4 32-bit RISC
- Feature: a full set of single-cycle DSP instructions
- Operating Frequency: 168MHz, 210 DMIPS/1.25 DMIPS/MHz
- Operating Voltage: 1.8V-3.6V
- Package: LQFP100
- Memories: 512kB Flash, 192+4kB SRAM
- MCU communication Interfaces:
-- 3 x SPI, 3 x USART, 2 x UART, 2 x I2S, 3 x I2C
-- 1 x FSMC, 1 x SDIO, 2 x CAN
-- 1 x USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, ULPI and on-chip full-speed PHY
-- 1 x 10/100 Ethernet MAC
-- 1 x 8 to 12-bit parallel camera interface
- AD & DA converters: 3 x AD (12-bit, 1μs, shares 24 channels); 2 x DA (12-bit)
- Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP
2. AMS1117-3.3 (on bottom side): 3.3V voltage regulator
3. MIC2075 (on bottom side): onboard USB power management device
4. Power supply switch, powered from 5Vin or USB connection
5. Boot mode switch, for configuring BOOT0 pin
6. Power indicator
7. Reset button
8. 8M crystal oscillator
9. 32.768K crystal (on bottom side), for internal RTC with calibration
10. JTAG/SWD interface: for debugging/programming
11. USB connector, used for establishing USB communication between PC and the STM32 development board
12. IO expander (including VCC/GND), all the MCU pins are accessible on expansion connectors for further expansion
13. 5Vin pinheader, 5V power supply is required when using USB HOST/OTG
14. USB jumper
- Short the jumper when using USB
- Open the jumper to disconnect from I/O ports
15. VBAT selection jumper
- Short the jumper to use system power supply
- Open the jumper to connect the VBAT to external power, such as battery
16. VREF selection jumper
- Short the jumper to connect VREF+/VREF- to VCC/GND
- Open the jumper to connect VREF+/VREF- to other custom pin via jumper wire

Package Contents
1. Core407V development board x 1
2. USB type A to Mini-B cable x 1
3. Software CD x 1

Waveshare Core407V, STM32F4 Core Board

Product form

SKU: ZY13990393

  • In stock (Processing Time 1 - 72 hours)

€31,12

    • Guaranteed secure & safe checkout.

    Icon for truckShipping Methods

    To find out all available shipping methods, and the exact delivery time add the product to the cart and verify it using our shipping calculator.

    Icon for 24_hour_clockOrder Processing Time

    All orders are shipped within a maximum of 72 hours from the order's arrival.

    Icon for coinMoney Back Guarantee

    Garmade Money Back Guarantee- Get the item you ordered or your money back, it's that simple.

    Icon for image_placeholderMismatched Product

    Product doesn't match the description? Contact us within 31 days after you receive it!

    Icon for mobile_paymentRefunds

    In case of cancellation, money will be refunded to your account within 14 days.

    Description

    Overview
    1. Core407V is a small STM32 development board that features an STM32F407VET6 device as the microcontroller, supports further expansion. It is ideal for starting application development with STM32F family.
    2. As a minimal ready-to-run system, the Core407V integrates USB communication interface, JTAG/SWD programming/debugging interface, clock circuit, USB power management, boot mode selection, and so on.
    3. Furthermore, pin headers on the backside allow the Core407V to be plugged-in your application board and act as the MCU core circuit in your system. All the I/O ports are accessible on the pin headers, and the header pitch is designed as 2.54mm.

    What has On Board
    1. STM32F407VET6: The high performance STM32 MCU which features:
    - Core: Cortex-M4 32-bit RISC
    - Feature: a full set of single-cycle DSP instructions
    - Operating Frequency: 168MHz, 210 DMIPS/1.25 DMIPS/MHz
    - Operating Voltage: 1.8V-3.6V
    - Package: LQFP100
    - Memories: 512kB Flash, 192+4kB SRAM
    - MCU communication Interfaces:
    -- 3 x SPI, 3 x USART, 2 x UART, 2 x I2S, 3 x I2C
    -- 1 x FSMC, 1 x SDIO, 2 x CAN
    -- 1 x USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, ULPI and on-chip full-speed PHY
    -- 1 x 10/100 Ethernet MAC
    -- 1 x 8 to 12-bit parallel camera interface
    - AD & DA converters: 3 x AD (12-bit, 1μs, shares 24 channels); 2 x DA (12-bit)
    - Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP
    2. AMS1117-3.3 (on bottom side): 3.3V voltage regulator
    3. MIC2075 (on bottom side): onboard USB power management device
    4. Power supply switch, powered from 5Vin or USB connection
    5. Boot mode switch, for configuring BOOT0 pin
    6. Power indicator
    7. Reset button
    8. 8M crystal oscillator
    9. 32.768K crystal (on bottom side), for internal RTC with calibration
    10. JTAG/SWD interface: for debugging/programming
    11. USB connector, used for establishing USB communication between PC and the STM32 development board
    12. IO expander (including VCC/GND), all the MCU pins are accessible on expansion connectors for further expansion
    13. 5Vin pinheader, 5V power supply is required when using USB HOST/OTG
    14. USB jumper
    - Short the jumper when using USB
    - Open the jumper to disconnect from I/O ports
    15. VBAT selection jumper
    - Short the jumper to use system power supply
    - Open the jumper to connect the VBAT to external power, such as battery
    16. VREF selection jumper
    - Short the jumper to connect VREF+/VREF- to VCC/GND
    - Open the jumper to connect VREF+/VREF- to other custom pin via jumper wire

    Package Contents
    1. Core407V development board x 1
    2. USB type A to Mini-B cable x 1
    3. Software CD x 1

    Additional Information

    Icon for truckShipping Info

    IMPORTANT INFO - PLEASE CHECK BEFORE ORDERING.



      Estimated transit time and postage fee depends on the method you choose at checkout. Please add the desired product to the cart and there you will be able to see all this information.

      Complete and right address is the guarantee of fast and efficient delivery, so please kindly recheck it when you place an order.

      In order to ensure a fast and efficient delivery, we need to have the method of contact with you. Email and Phone Number is a very important detail and must be accurate. All orders with an incorrect email or phone number will be canceled immediately.

      We strive to dispatch all orders within 72 hours of placing your order. But sometimes if the order is big or the products are more sophisticated, it can take a little longer. As soon as we dispatched it, you will receive a confirmation email along with a tracking number.

      Please be aware that sometimes due to unclear address, hard to access, no answer at address, the package can be kept at your local post office for collection. In this case you will be informed by the delivery company and by us. Please also monitor the tracking number.

      For European Union Countries:
    - If your order is less than 150€ excluding shipping costs, then the Taxes are already included in the price. This means that there will be NO extra charge upon delivery.
    - If your order is more than 150€, you will NOT be charged Taxes at the checkout, and you will have to pay upon delivery based on your local VAT rate.

     

    Icon for reviewReviews

    Login

    Forgot your password?

    Don't have an account yet?
    Create account