Mini 8 Band SSB/CW QRP Transceiver For Ham Radio, Style: Host+Hand Mi

Description


Features:
1. IRF series transmitter tubes, durable
2. Can be used to connect the antenna (instrument base)
3. Aluminum laser case marking, all aluminum buttons, translucent silicone keys
4. The original qck circuit is greatly simplified, the installation components are reduced, and the complex transformer windings and wiring procedures are not needed, and the construction is easy (green and red)
5. 8-band, digital display, external power supply 13.8 v 10W, built-in 12.6 V battery

Features list:
1. Simple, interesting and versatile cxp ssb high frequency transceiver with built-in dsp and sdr functions
2. Eer class e drives the ssb launch phase
3. 13.8v power supply about 10w ssb pep output
4. Filters: 4000,2500,1700,500,200,100,50hz passband
5. Dsp functions: automatic gain control (agc) , noise reduction (nr) , voice trigger, voice trigger XMIT, attenuator rx (att) , tx noise gate, tx drive control, volume control, dbm/s-meter
6. Ssb reverse sideband/carrier suppression transmission: better than -45 dbc, imd3(double tone) -33 dbc, receive: better than -50 dbc
7. Multi-band support, continuously adjustable in the 160m-10m frequency range (loss of 20khz performance)99mhz
8. Open source firmware, built into IDE; allows experimentation, new features can be added, contributions can be shared via github, software complexity: 2000 lines of code
9. V-based software can be used for fast and complete rogue operations (qsk and semi-qsk) , or to assist execution in digital mode (without cat or ptt interface) for rx/tx switches with tx/pa delay control, external ptt output-simple installation and modification, 8 component changes and 8 lines
10. Lightweight, low-cost Transceiver: eer electronic level transmitter, which has high power efficiency (without the need for a large radiator) and simple design (without the need for complex balanced linear power amplifier)
11. SSB transmitter phase is completely digital and software-based: controls the phase of the SI5351 PLL (via small I2C frequency changes over 800 kbit/s) and the amplitude of the PA (via pwm to pwm) to test the microphone input and reconstruct the SSB signal. Key shaping circuit PA)
12. All-digital and software-based SDR receiver level (optional) : sampling of I/Q signals (plural) from a digital mixer with an orthogonal sampling detector, and in which the implementation of the 90-degree phase shift (Hilber transform) software and by adding remove sideband
13. Three switchable analog governors independent of the front-end receiver
14. MDS receiver noise level: -135 dbm (200 hz bw) at 28 mhz
15. Pre-receiver selectivity: steep frequency adjustment -45 db/10 rollover
16. Blocking dynamic range: 20khz offset 123db, 2khz offset 78db
17. CW decoder, corresponding relays with filters switched via i2c-Cat support (TS480 subset) , you can stream audio, keystrokes, and display text through CAT

Port description:
1. Charging: built-in lithium battery charging port, only use the attached charger! Do not use other chargers!
2. Switch: off, bat: built-in Battery Power, 13.8: external power supply
3. DC13.8V/3A: external power interface
4. Key: automatic Key body connection (a, b, single Key)
5. Pa: external power amplifier, ptt signal
6. Mic: external microphone interface
7. Uart: serial communication (TS-480 compatible instruction)
8. Spk: external speaker

Product specifications:
1. Battery capacity: 6000 mah
2. Side PTT with built-in Mic for handheld use
3. Using power MOS transistor, not easy to break
4. Built-in battery, built-in microphone, speakers, can be connected to automatic keys, but also CW decoding
5. Size: 13.3 x 7.5 x 4cm

Packing list:
-.1 x host
-.1 x hand Mi
-.1 x power (host + hand does not come with)
-.1 x three-in-one screwdriver

Mini 8 Band SSB/CW QRP Transceiver For Ham Radio, Style: Host+Hand Mi

Product form

SKU: TBD0603020503

  • In stock (Processing Time 1 - 72 hours)

826,74 zł

    • Guaranteed secure & safe checkout.

    Icon for truckShipping Methods

    To find out all available shipping methods, and the exact delivery time add the product to the cart and verify it using our shipping calculator.

    Icon for 24_hour_clockOrder Processing Time

    All orders are shipped within a maximum of 72 hours from the order's arrival.

    Icon for coinMoney Back Guarantee

    Garmade Money Back Guarantee- Get the item you ordered or your money back, it's that simple.

    Icon for image_placeholderMismatched Product

    Product doesn't match the description? Contact us within 31 days after you receive it!

    Icon for mobile_paymentRefunds

    In case of cancellation, money will be refunded to your account within 14 days.

    Description


    Features:
    1. IRF series transmitter tubes, durable
    2. Can be used to connect the antenna (instrument base)
    3. Aluminum laser case marking, all aluminum buttons, translucent silicone keys
    4. The original qck circuit is greatly simplified, the installation components are reduced, and the complex transformer windings and wiring procedures are not needed, and the construction is easy (green and red)
    5. 8-band, digital display, external power supply 13.8 v 10W, built-in 12.6 V battery

    Features list:
    1. Simple, interesting and versatile cxp ssb high frequency transceiver with built-in dsp and sdr functions
    2. Eer class e drives the ssb launch phase
    3. 13.8v power supply about 10w ssb pep output
    4. Filters: 4000,2500,1700,500,200,100,50hz passband
    5. Dsp functions: automatic gain control (agc) , noise reduction (nr) , voice trigger, voice trigger XMIT, attenuator rx (att) , tx noise gate, tx drive control, volume control, dbm/s-meter
    6. Ssb reverse sideband/carrier suppression transmission: better than -45 dbc, imd3(double tone) -33 dbc, receive: better than -50 dbc
    7. Multi-band support, continuously adjustable in the 160m-10m frequency range (loss of 20khz performance)99mhz
    8. Open source firmware, built into IDE; allows experimentation, new features can be added, contributions can be shared via github, software complexity: 2000 lines of code
    9. V-based software can be used for fast and complete rogue operations (qsk and semi-qsk) , or to assist execution in digital mode (without cat or ptt interface) for rx/tx switches with tx/pa delay control, external ptt output-simple installation and modification, 8 component changes and 8 lines
    10. Lightweight, low-cost Transceiver: eer electronic level transmitter, which has high power efficiency (without the need for a large radiator) and simple design (without the need for complex balanced linear power amplifier)
    11. SSB transmitter phase is completely digital and software-based: controls the phase of the SI5351 PLL (via small I2C frequency changes over 800 kbit/s) and the amplitude of the PA (via pwm to pwm) to test the microphone input and reconstruct the SSB signal. Key shaping circuit PA)
    12. All-digital and software-based SDR receiver level (optional) : sampling of I/Q signals (plural) from a digital mixer with an orthogonal sampling detector, and in which the implementation of the 90-degree phase shift (Hilber transform) software and by adding remove sideband
    13. Three switchable analog governors independent of the front-end receiver
    14. MDS receiver noise level: -135 dbm (200 hz bw) at 28 mhz
    15. Pre-receiver selectivity: steep frequency adjustment -45 db/10 rollover
    16. Blocking dynamic range: 20khz offset 123db, 2khz offset 78db
    17. CW decoder, corresponding relays with filters switched via i2c-Cat support (TS480 subset) , you can stream audio, keystrokes, and display text through CAT

    Port description:
    1. Charging: built-in lithium battery charging port, only use the attached charger! Do not use other chargers!
    2. Switch: off, bat: built-in Battery Power, 13.8: external power supply
    3. DC13.8V/3A: external power interface
    4. Key: automatic Key body connection (a, b, single Key)
    5. Pa: external power amplifier, ptt signal
    6. Mic: external microphone interface
    7. Uart: serial communication (TS-480 compatible instruction)
    8. Spk: external speaker

    Product specifications:
    1. Battery capacity: 6000 mah
    2. Side PTT with built-in Mic for handheld use
    3. Using power MOS transistor, not easy to break
    4. Built-in battery, built-in microphone, speakers, can be connected to automatic keys, but also CW decoding
    5. Size: 13.3 x 7.5 x 4cm

    Packing list:
    -.1 x host
    -.1 x hand Mi
    -.1 x power (host + hand does not come with)
    -.1 x three-in-one screwdriver

    Additional Information

    Icon for truckShipping Info

    IMPORTANT INFO - PLEASE CHECK BEFORE ORDERING.



      Estimated transit time and postage fee depends on the method you choose at checkout. Please add the desired product to the cart and there you will be able to see all this information.

      Complete and right address is the guarantee of fast and efficient delivery, so please kindly recheck it when you place an order.

      In order to ensure a fast and efficient delivery, we need to have the method of contact with you. Email and Phone Number is a very important detail and must be accurate. All orders with an incorrect email or phone number will be canceled immediately.

      We strive to dispatch all orders within 72 hours of placing your order. But sometimes if the order is big or the products are more sophisticated, it can take a little longer. As soon as we dispatched it, you will receive a confirmation email along with a tracking number.

      Please be aware that sometimes due to unclear address, hard to access, no answer at address, the package can be kept at your local post office for collection. In this case you will be informed by the delivery company and by us. Please also monitor the tracking number.

      For European Union Countries:
    - If your order is less than 150€ excluding shipping costs, then the Taxes are already included in the price. This means that there will be NO extra charge upon delivery.
    - If your order is more than 150€, you will NOT be charged Taxes at the checkout, and you will have to pay upon delivery based on your local VAT rate.

     

    Icon for reviewReviews

    Customer Reviews

    Be the first to write a review
    0%
    (0)
    0%
    (0)
    0%
    (0)
    0%
    (0)
    0%
    (0)

    Login

    Forgot your password?

    Don't have an account yet?
    Create account