Products

Features1. 3W high-power 850 infrared LED2. Onboard photoresistor, the ambient light detector3. Onboard adjustable resistor, for controlling the ambient light threshold of toggling the infrared LED4. Allows adding night vision function to cameras which feature embedded infrared filter :a) 100 degree field of view, two pieces of LED is required to get wider field of viewb) Supported devices : RPi Camera (E), RPi Camera (F), RPi Camera (H)How to Use1. Connect the Infrared LED Board to the camera PCB by screws2. The screw holes are used for both attachment and power supply3. Adjust the adjustable resistor to set a proper ambient light threshold, which toggles the infrared LED automatically4. When ambient light is lower than threshold value, the infrared LED is on, vice versaNote :1. Limited by the Raspberry Pi power supply, the 3W high-power infrared LED might cause the Pi to increase heating, heat sinks are suggested.2. Ideal imaging distance is within 3m. When the distance goes up to 6m, the night vision camera can just capture blurry outlines.

Read more less

OverviewEmitting a beam of infrared, and receive the reflected beamFeatures wide range voltage comparator LM393Adjustable sensitivitySignal output indicatorSpecificationsPower: 3.3V ~ 5VDimension: 39mm × 15.5mm (include the IR LED)Mounting holes size: 3mmDetection range: 2cm ~ 30cm (depending on the obstacle's color, farthest for white)Detection angle: 35°Recommended environment: in door, to avoid the sunshine effectApplicationsRobot path trackingObstacle-avoiding carPipeline counterHow to UseIn the case of working with a MCU:VCC ↔ 3.3V ~ 5VGND ↔ GNDAOUT ↔ MCU.IO (analog output)DOUT ↔ MCU.IO (digital output)

Read more less

Overview1. Reflective infrared Transceiver2. Features wide range voltage comparator LM3933. Adjustable sensitivity4. Signal output indicatorSpecifications1. Power: 3.0V ~ 5.3V2. Dimension: 25mm * 15.9mm3. Mounting holes size: 2.0mmApplications1. Robot path tracking2. Obstacle-avoiding car3. Pipeline counterHow to UseIn the case of working with a MCU:Pinouts1. VCC: 3.0V ~ 5.3V2. GND: Power supply ground3. AOUT: MCU.IO (analog output)4. DOUT : MCU.IO (digital output)Package Contents1. Infrared Reflective Sensor x12. 4-pin custom connector jumper wire x1

Read more less

1. Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards2. 1-Ch CAN, adopts MCP2515 controller and CAN transceiver, converts SPI to CAN3. 2-Ch RS485, adopts SC16IS752+SP3485 dual-chip combination, converts SPI to RS4854. Onboard power conversion circuit, supports 8~28V wide voltage power supply, can power the Raspberry Pi at the same time5. Onboard unibody power supply isolation, providing stable isolated voltage, no extra power supply required for the isolated terminal6. Onboard unibody digital isolation, for isolating the signal, reliable and jamproof, low power consumption7. Onboard TVS (Transient Voltage Suppressor), effectively suppress surge voltage and transient spike voltage in the circuit, lightningproof & anti-electrostatic8. Onboard resettable fuse and protection diodes, ensures the current/voltage stable outputs, provides over-current/over-voltage proof, improves shock resistance9. Onboard 120Ω terminal resistor, configured by jumper10. Onboard terminals and pin headers, more convenient connection11. Breakout SPI control pins, for connecting with host control boards

Read more less

Features1. Quality chassis with track: Adopting 37-520 full-metal DC geared motor, High torque, low noise 2. 180 degree wide angle rotation, flexible controlling robotic arm 3. Quality serial bus full-metal digital servo: High torque, high precision, preventing, it from being stuck and pamaged 4. Auto collision avoidance: Collecting data via camera by taking enough images of different conditions, using the data to train the neutral network, combined With AI algorithm, achieving auto collision avoidance on sorts of environments. 5. Motion detection: Capturing moving objects on the video by motion detection 6. Color recognition and tracking: Recognizing and locking specified color by camera, and then using pan & tilt to track the specified color automatically 7. 3D coordinate system controlled robotic arm, calculated via Inverse Kinematics algorithm: Input coordinate of the target, calculating the moving angles of the 4-DOF servos by inverse kinematics algorithm, and then controlling the servos via serial bus, moving the robotic arm to reach target position 8. JupyterLab programming: JupyterLab is a web-based interactive development environment, supports multi data formats including code, document, image/video, UI control interface, etc., provides rich visualized output, allows easily creating dashboard and UI, supports flexible configuration and arrangement for modular interface. 9. 8MP 160 degree FOV camera: IMX219 sensor, 3280 x2464 resolutionPackage List1. Aluminum alloy kit x1 2. JETANK expansion board x1 3. Wireless-AC8265 with antenna x1 4. IMX219-160 Camera x1 5. Acrylic camera spacer x1 6. Camera FFC x1 7. 0.91inch OLED x1 8. 12.6V 2A power supply + additional EU head x1 9. Robotic arm gripper x1 10. Thrust bearing x1 11. Flange bearing x2 12. Coupler x2 13. Gearmotor x2 14. 5264 servo wire x1 15. Track kit (including bolt, nut, and screwdriver) x2 16. 2 x 5 Pin wire x1 17. Spanner x1 18. L-form hex socket spanner 2PCS x1 19. SCS15-AP servo x4 20. Screwdriver 2PCS x1 21. SCS15-S servo x1 22. Card reader x1 23. Mini cross wrench sleeve x2 24. Cooling fan x1 25. PH2.0 4PIN dual connector cable x1 26. Screws pack x1

Read more less

Overview1. Smart robot is always the favorite project of electronic enthusiasts, however, a robot will be "not that smart" if it is not AI-based.2. Welcome the JetBot, an actual smart robot powered by Jetson Nano. With the intelligent eye (front camera), facial recognition, object tracking, auto line following, and collision avoidance can be easily achieved. It also comes with ROS nodes code, which makes it easy to get started with the open source ROS (Robot Operating System), and to learn the system framework and concepts of ROS.3. If you have got a Jetson Nano on your desk right now, combined with our open source codes and tutorials, these add-ons would be the ideal choice for you to learn AI robot designing and development.Features1. Adopts 3x 18650 batteries (NOT included), high battery capacity, up to 12.6V voltage output, more powerful driving force.2. Integrates S-8254AA + AO4407A lithium battery protection circuit, provides protections for over-charge, over-discharge, over-current, and short circuit.3. Onboard APW7313 voltage regulator, provides stable 5V voltage for the Jetson Nano.4. Onboard TB6612FNG dual H-bridge motor driver.5. Onboard 0.91inch 128×32 pixels OLED, allows to display robot IP address, RAM, battery life, etc.6. Onboard ADS1115 AD acquisition chip for monitoring the battery in real time.7. Weight: 773gWhat is on the JetBot Expansion Board1. S-8254AA: Lithium battery protector, provides protections for over-charge, over-discharge, over-current, and short circuit2. ADS1115: 16-bit AD acquisition chip, monitoring the battery in real time3. AO4407A:: P-Channel MOSFET for protection circuit4. APW7313:: 5V power regulator for powering the Jetson Nano5. PCA9685: PWM controller, I2C interface, for IO expansion6. TB6612FNG: dual H-bridge motor driver7. 0.91inch OLED: SSD1306 driver chip, 128×32 pixels8. Battery charger input: charging the 3x 18650 batteries9. Power switch10. 18650 battery holder11. Motor connector (bottom side)12. Jetson Nano communication header: I2C interface and power supplyPacking List1. Metal box x12. Camera holder x13. Acrylic piece x14. Jetbot expansion board x15. IMX219-160 Camera x16. Wireless-AC8265 x17. Motor 2PCS x18. Wheel 2PCS x19. Omni-direction wheel 2PCS x110. Power adapter EU head x111. 12.6V battery charger x112. Wireless gamepad x113. Screwdriver 2PCS x114. 6Pin 9cm cable x115. Screws pack x116. Spanner x117. Cooling fan x118. Micro SD card reader x1

Read more less

OverviewSmart robot is always the favorite project of electronic enthusiasts, however, a robot will be "not that smart" if it is not AI-based.Welcome the JetBot, an actual smart robot powered by Jetson Nano. With the intelligent eye (front camera), facial recognition, object tracking, auto line following, and collision avoidance can be easily achieved. It also comes with ROS nodes code, which makes it easy to get started with the open source ROS (Robot Operating System), and to learn the system framework and concepts of ROS.Features1. Adopts 3x 18650 batteries (NOT included), high battery capacity, up to 12.6V voltage output, more powerful driving force.2. Integrates S-8254AA + AO4407A lithium battery protection circuit, provides protections for over-charge, over-discharge, over-current, and short circuit.3. Onboard APW7313 voltage regulator, provides stable 5V voltage for the Jetson Nano.4. Onboard TB6612FNG dual H-bridge motor driver.5. Onboard 0.91inch 128×32 pixels OLED, allows to display robot IP address, RAM, battery life, etc.6. Onboard ADS1115 AD acquisition chip for monitoring the battery in real time.7. Weight: 1029gWhat is on the JetBot Expansion Board1. S-8254AA: Lithium battery protector, provides protections for over-charge, over-discharge, over-current, and short circuit2. ADS1115: 16-bit AD acquisition chip, monitoring the battery in real time3. AO4407A: P-Channel MOSFET for protection circuit4. APW7313: 5V power regulator for powering the Jetson Nano5. PCA9685: PWM controller, I2C interface, for IO expansion6. TB6612FNG: dual H-bridge motor driver7. 0.91 inch OLED: SSD1306 driver chip, 128×32 pixels8. Battery charger input: charging the 3x 18650 batteries9. Power switch10. 18650 battery holder11. Motor connector (bottom side)12. Jetson Nano communication header: I2C interface and power supplyPacking List1. Jetson Nano Developer Kit x12. Micro SD Card 64GB ×13. Metal box x14. Camera holder x15.Acrylic piece x16. Jetbot expansion board x17. IMX219-160 Camera x18. Wireless-AC8265 x19. Motor 2PCS x110. Wheel 2PCS x111.Omni-direction wheel 2PCS x112. Power adapter EU head x113. 12.6V battery charger x114. Wireless gamepad x115. Screwdriver 2PCS x116. 6Pin 9cm cable x117. Screws pack x118. Spanner x119. Cooling fan x120. Micro SD card reader x1

Read more less

Features1. Onboard three 18650 batteries, 7800mAh, up to 12.6V voltage output, and stronger motor power (not included batteries). 2. Onboard S-8254AA + AO4407A lithium battery protection circuit, with anti-overcharge, anti-over-discharge, anti-over-current and short-circuit protection functions. 3. The onboard APW7313 voltage regulator chip can provide a stable 5V voltage to the Jetson Nano. 4. The onboard TB6612FNG dual H-bridge motor driver chip can drive the left and right motors to work. 5. Onboard 0.91-inch 128 x 32 resolution OLED, real-time display of car IP address, memory, power, etc. 6. The onboard ADS1115 AD acquisition chip is convenient for real-time monitoring of battery power.Package List1. Jetson Nano 2GB Developer Kit 2. Micro SD Card 64GB 3. JetRacer metal kit 6PCS 4. EVA felt pad 2PCS 5. 3D-printed motor lid 6. JetRacer expansion board 7. IMX219-160 Camera 8. USB wireless NIC 9. Acrylic piece 10. Servo mount 11. Metal Gearmotor 2PCS 12. Tire 4PCS 13. Coupler 2PCS 14. MG996R servo 15. MG996R servo wheel 16. Steering knuckle 2PCS 17. Ball bearing 4PCS 18. M3 plastic ball joint 4PCS 19. M3 pull bar 2PCS 20. 12.6V 2A battery charger + EU head 21. Wireless gamepad 22. 6Pin cable 23. Spanner 2PCS 24. Screwdriver 2PCS 25. Mini cross wrench sleeve 26. 4010 cooling fan 27. Micro SD card reader 28. Screws pack 29. Track map

Read more less

About The ProductThis is an AI Racing Robot kit based on Jetson Nano Developer Kit. Supports deep learning, auto line following, autonomous driving and so on.Specifications1. Camera: 8MP HD resolution, 160 degree FOV wide angle camera 2. OLED: 0.91 inch 128 x 32 pixels 3. Wireless: AC8265 4. Driving Type: Ackerman steering / Dual gearmotor rear wheel drive 5. Power supply: 12.6V, 18650 battery x 3 (connected in series). Note: the 18650 batteries are NOT included. 6. Motor: - 37-520 DC gearmotor - Reduction rate 1:10 - Idle speed 740RPM 7. Chassis: Aluminum alloy chassis 8. Program library: JetRacer, DonkeyCar 9. Suggestion: Competition level; Experienced programming skill requiredPackage List2. EVA felt pad 2PCS 3. 3D-printed motor lid 4. JetRacer expansion board 5. IMX219-160 Camera 6. Wireless-AC8265 7. Acrylic piece 8. Servo mount 9. Metal Gearmotor 2PCS 10. Tire 4PCS 11. Coupler 2PCS 12. MG996R servo 13. MG996R servo wheel 14. Steering knuckle 2PCS 15. Ball bearing 4PCS 16. M3 plastic ball joint 4PCS 17. M3 pull bar 2PCS 18. 12.6V battery charger + EU head 19. Wireless gamepad 20. 6Pin cable 21. Spanner 2PCS 22. Screwdriver 2PCS 23. Mini cross wrench sleeve 24. 4010 cooling fan 25. Micro SD card reader 26. Screws pack 27. Track map

Read more less

About The ProtuctThis is an AI Racing Robot kit based on Jetson Nano 2GB Developer Kit. Supports deep learning, auto line following, autonomous driving, and so on.NoticeWe do not provide batteries in the AI Kit or the Acce Package because of the shipping policy, you need to buy batteries in the local market.Specifications1. Camera: 8MP HD resolution, 160 degree FOV wide angle camera 2. OLED: 0.91 inch 128 x 32 pixels 3. Wireless: USB 4. Driving Type: Ackerman steering / High speed motors 4WD / Front and rear axle differentials 5. Shock Absorber: Adjustable oil-filled shocks / 4WD independent suspension 6. Power supply: 8.4V, 18650 battery x 4 (two in parallel, two in series). Note: the 18650 batteries are NOT included. 7. Servo: 6kg/cm torque 8. Chassis: Quality rugged plastic chassis 9. Crashproof: Front sponge 10. Program library: JetRacer, DonkeyCar 11. Suggestion: Competition level; Experienced programming skill requiredPackage List1. Jetson Nano 2GB Developer Kit 2. Micro SD Card 64GB 3. On-road chassis 4. JetRacer Pro expansion board 5. USB wireless NIC 6. IMX219-160 Camera 7. Acrylic camera spacer 8. Camera holder 9. Wireless gamepad 10. Cooling fan 11. 6Pin cable 12. Micro SD card reader 13. Spanner 14. Screwdriver x2 15. 8.4V 2A battery charger + EU head 16. Screws pack 17. Track map

Read more less

1. GPU: 128-core Maxwell 2. CPU: Quad-core ARM A57 1.43 GHz 3. Memory: 4GB 64-bit LPDDR4 25.6 GB/s 4. Storage: 16GB eMMC (no micro SD card slot) 5. Video encoder: 4K 30, 4x 1080p 30, 9x 720p 30 (H.264/H.265) 6. Video decoder: 4K 60, 2x 4K 30, 8x 1080p 30, 18x 720p 30 (H.264/H.265) 7. Camera: 2x MIPI CSI-2 DPHY lanes 8. Connectivity: Gigabit Ethernet, M.2 Key E expansion connector 9. Display: HDMI and DP 10. USB: 4x USB 3.0, USB 2.0 Micro-B 11. Extension interfaces: GPIO, I2C, I2S, SPI, UART 12. Dimensions: 100 x 80 x 29mm 13. Other: 260-pin connector

Read more less

FeaturesThe Pico-GPS-L76B is a GNSS module designed for Raspberry Pi Pico, with multi satellite systems support including GPS, BDS, and QZSS. It has advantages such as fast positioning, high accuracy, and low power consumption, etc. Combined with the Raspberry Pi Pico, it is easy to use global navigating function. 1. Standard Raspberry Pi Pico header, supports Raspberry Pi Pico series boards 2. Multi satellite systems support: GPS, BDS, and QZSS 3. Easy, self track prediction technology, help quick positioning 4. AlwaysLocate, intelligent controller of periodic mode for power saving 5. Support D-GPS, SBAS (WAAS/EGNOS/MSAS/GAGAN) 6. UART communication baudrate: 4800~115200bps (9600bps by default) 7. Onboard battery holder, supports ML1220 rechargeable cell, for preserving ephemeris information and hot starts 8. 4 x LEDs for indicating the module operating status 9. Come with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples)SpecificationGNSS 1. Frequency band: GPS L1 (1575.42Mhz), BD2 B1 (1561.098MHz) - Channels: 33 tracking ch, 99 acquisition ch, 210 PRN ch - C/A code - SBAS: WAAS, EGNOS, MSAS, GAGAN 2. Horizontal position accuracy (autonomous positioning): Less than 2.5m CEP 3. Time-To-First-Fix at -130dBm(EASY enabled): - Cold starts: Less than 15s - Warm starts: Less than 5s - Hot starts: Less than 1s 4. Sensitivity: - Acquisition: -148dBm - Tracking: -163dBm - Re-acquisition: -160dBm 5. Dynamic performance - Altitude (MAX): 18000m - Velocity (MAX): 515m/s - Acceleration (MAX): 4g Others 1. Communication interface: UART 2. Baudrate: 4800~115200bps (9600bps by default) 3. Update rate: 1Hz (default), 10Hz (MAX) 4. Protocols: NMEA 0183, PMTK 5. Power supply voltage: 5V 6. Operating current: 13mA 7. Overall current consumption: Less than 40mA at 5V (Continue mode) 8. Operating temperature: -40~ 85 degree C 9. Dimensions: 52 x 21mm

Read more less

L76X Multi-GNSS HAT for Raspberry Pi, Supports GPS, BDS, QZSSOverview1. This is a Raspberry Pi GNSS HAT which supports Multi-GNSS systems: GPS, BDS, and QZSS, with advantages such as fast positioning, high accuracy, low power consumption, and so on.2. It is an easy way to enable global positioning function for your Raspberry Pi.Features1. Support Multi-GNSS systems: GPS, BDS, and QZSS2. EASY, self track prediction technology, help quick positioning2. AlwaysLocate, intelligent controller of periodic mode for power saving3. Support DGPS, SBAS (WAAS/EGNOS/MSAS/GAGAN)4. UART communication baudrate: 4800~115200bps (9600bps by default)5. Onboard battery holder, supports ML1220 rechargeable battery, for preserving ephemeris information and hot starts6. 4x LEDs for indicating the module working status7. Come with development resources and manual (examples for Raspberry Pi/Arduino/STM32)GNSS Specifications1. Band: GPS L1(1575.42Mhz), BD2 B1 (1561.098MHz)- Channels: 33 tracking ch, 99 acquisition ch, 210 PRN ch- C/A code- SBA: WAAS, EGNOS, MSAS, GAGAN2. Horizontal position accuracy:- Autonomous: <2.5mCEP3. Time-To-First-Fix @-130dBm (EASY™ enabled):- Cold starts: <15s- Warm starts: <5s- Hot starts: <1s4. Sensitivity:- Acquisition: -148dBm- Tracking: -163dBm- Re-acquisition: -160dBm5. Dynamic performance:- Altitude (max): 18000m- Velocity (max): 515m/s- Acceleration (max): 4GGeneral Specifications1. Communication interface: UART2. Baudrate: 4800~115200bps (9600bps by default)3. Update rate: 1Hz (default), 10Hz (max)4. Protocols: NMEA 0183, PMTK5. Power supply voltage: 5V / 3.3V6. Operating current: 13mA7. Operating temperature: -40 degree C ~ 85 degree C8. Dimensions: 65mm x 30.5mmApplications1. Vehicle tracking2. Asset tracking3. Security system4. Industrial PDA5. GIS applicationWhat is on Board1. L76B module2. CP2102: USB TO UART converter3. CAT24C32: EEPROM4. RT9193-33: Power manager5. Backup mode wakeup button6. Standby switch7. Indicators:- RXD/TXD: UART RX/TX indicator- PPS: GPS status indicator- PWR: Power indicator8. Raspberry Pi GPIO connector: For connecting with Raspberry Pi9. USB TO UART port10. GNSS antenna connector11. Battery holder: Support ML1220 rechargeable battery, for preserving ephemeris information and hot starts12. UART selection jumpers- A: control the L76B through USB TO UART- B: control the L76B through Raspberry Pi- C: access Raspberry Pi through USB TO UARTPackage Contents1. L76X GPS HAT x12. GPS External Antenna (B) x13. USB type A plug to micro plug cable x14. RPi screws pack (2pcs) x15. 2x20PIN pinheader x1

Read more less

OverviewThis is a general GNSS module which supports Multi-GNSS systems: GPS, BDS, and QZSS, with advantages such as fast positioning, high accuracy, low power consumption, and so on.Features1. Support Multi-GNSS systems: GPS, BDS, and QZSS2. EASY, self track prediction technology, help quick positioning3. AlwaysLocate, intelligent controller of periodic mode for power saving4. Support DGPS, SBAS (WAAS/EGNOS/MSAS/GAGAN)5. UART communication baudrate: 4800~115200bps (9600bps by default)6. Onboard rechargeable Li battery MS621FE, for preserving ephemeris information and hot starts7. 2x LEDs for indicating the module working status8. Come with development resources and manual (examples for Raspberry Pi/Arduino/STM32)GNSS Specifications1. Band: GPS L1(1575.42Mhz), BD2 B1 (1561.098MHz)2. Channels: 33 tracking ch, 99 acquisition ch, 210 PRN ch3. C/A code4. SBA: WAAS, EGNOS, MSAS, GAGAN5. Horizontal position accuracy:- Autonomous: <2.5mCEP6. Time-To-First-Fix @-130dBm (EASY enabled):- Cold starts: <15s- Warm starts: <5s- Hot starts: <1s7. Sensitivity:- Acquisition: -148dBm- Tracking: -163dBm- Re-acquisition: -160dBm8. Dynamic performance:- Altitude (max): 18000m- Velocity (max): 515m/s- Acceleration (max): 4GGeneral Specifications1. Communication interface: UART2. Baudrate: 4800~115200bps (9600bps by default)3. Update rate: 1Hz (default), 10Hz (max)4. Protocols: NMEA 0183, PMTK5. Power supply voltage: 5V / 3.3V6. Operating current: 11mA7. Operating temperature: -40℃ ~ 85℃8. Dimensions: 32.5mm x 25.5mmApplications1. Vehicle tracking2. Asset tracking3. Security system4. Industrial PDA5. GIS applicationPackage Contents1. L76X GPS Module x12. PH2.0 5PIN wire x1

Read more less

OverviewOutput voltage boosts along with the immersion depth of the moduleSpecifications1. Detection depth: 48mm2. Power: 2.0V ~ 5.0V3. Dimension: 19.0mm * 63.0mm4. Mounting holes size: 2.0mmApplicationsWater level alarmHow to UseIn the case of working with a MCU:1. VCC-- 2.0V ~ 5.0V2. GND--Power supply ground3. AOUT--MCU.IO (analog output)

Read more less

Features:1. Using microbolometer and thermopile hybrid technology, 80x62 array pixels2. Continuous operation and thermal video streaming due to shutterless design3. Noise equivalent temperature difference (NETD) 150mK RMS@1Hz refresh rate4. Up to 25FPS (maximum) thermal imaging video stream output5. Comes with online resources and manuals (Python demo for Raspberry Pi, Android/Windows host and user manual, etc.)main application:1. High-precision long-term non-contact temperature online monitoring2. Infrared thermal imaging equipment, infrared thermometer3. Smart home, smart building, smart lighting4. Industrial temperature control, security and safety, intrusion/motion detection5. Small target thermal analysis, thermal trend analysis and solutionsProduct parameters:1. Power supply: 5V2. Working current: 61mA@5V3. Wavelength range: 8-14 microns4. Working temperature: minus 20-85 degrees Celsius5. Target temperature: minus 20-400 degrees Celsius6. Refresh rate: 25 FPS7. Field of view: 45 degrees (horizontal) × 45 degrees (vertical)8. Noise equivalent temperature difference: 150mK9. Measurement accuracy: 2 degrees Celsius (ambient temperature 10-70 degrees Celsius)10. Product size: 40PIN GPIO Header: 65×30.5mm, Type-C Port: 62×13.2mm11. Weight: 40PIN GPIO Header: 21 grams, Type-C Port: 33 gramsPacking list:-40PIN GPIO Header/Type-C Port x1-40PIN row seat x1-FPC 15 PIN cable 0.3mm pitch 100mm x1-Screw pack x1

Read more less

Features:1. Using microbolometer and thermopile hybrid technology, 80x62 array pixels2. Continuous operation and thermal video streaming due to shutterless design3. Noise equivalent temperature difference (NETD) 150mK RMS@1Hz refresh rate4. Up to 25FPS (maximum) thermal imaging video stream output5. Comes with online resources and manuals (Python demo for Raspberry Pi, Android/Windows host and user manual, etc.)main application:1. High-precision long-term non-contact temperature online monitoring2. Infrared thermal imaging equipment, infrared thermometer3. Smart home, smart building, smart lighting4. Industrial temperature control, security and safety, intrusion/motion detection5. Small target thermal analysis, thermal trend analysis and solutionsProduct parameters:1. Power supply: 5V2. Working current: 61mA@5V3. Wavelength range: 8-14 microns4. Working temperature: minus 20-85 degrees Celsius5. Target temperature: minus 20-400 degrees Celsius6. Refresh rate: 25 FPS7. Field of view: 45 degrees (horizontal) × 45 degrees (vertical)8. Noise equivalent temperature difference: 150mK9. Measurement accuracy: 2 degrees Celsius (ambient temperature 10-70 degrees Celsius)10. Product size: 40PIN GPIO Header: 65×30.5mm, Type-C Port: 62×13.2mm11. Weight: 40PIN GPIO Header: 21 grams, Type-C Port: 33 gramsPacking list:-40PIN GPIO Header/Type-C Port x1-40PIN row seat x1-FPC 15 PIN cable 0.3mm pitch 100mm x1-Screw pack x1

Read more less

Overview1. This is a Raspberry Pi LoRa HAT based on SX1268, covers 433MHz frequency band. It allows data transmission up to 5km through serial port.2. By utilizing the new generation LoRa spread spectrum modulation technology, the communication distance of the module is as long as 5km, also supports auto repeating to transmit longer. Other features include Wake on Radio, wireless config, carrier sensing, communication key, and so on.3. Comparing with normal LoRa modules, the SX1268 LoRa HAT achieves longer communication distance, higher rate, lower consumption, better safety and anti-interference. It is suitable for various applications such as industrial control, smart home, data collection, etc.Features1.Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards2. Onboard CP2102 USB TO UART converter, for serial debugging3. Bring the UART control interface, for connecting host boards like Arduino/STM324. 4x LED indicators, easy to check the module status5. LoRa spread spectrum modulation technology, up to 84 available signal channel, longer communication distance, more robust to interference6. Auto multi-level repeating, suit for ultra long range communication, allows multi network on the same region7. Low power consumption features like deep sleeping and Wake on Radio, ideal for battery-powered applications8. Customizable communication key which wont be retrieved, greatly improves the security of user data9. Support LBT, monitoring the signal channel noise before transmitting, greatly improves the success ratio under extreme environment10. Support RSSI signal intensity indicating, for evaluating signal quality, tuning the network11. Support wireless parameter configuration, by sending wireless command/data packet, remotely configure or retrieve the module parameter12. Support fixed-point transmission, broadcast, signal channel monitor13. Come with development resources and manual (examples for Raspberry Pi/STM32)What is on Board1. SX1268 LoRa module2. 74HC125V: voltage level translator3. CP2102: USB TO UART converter4. Raspberry Pi GPIO connector: for connecting with Raspberry Pi5. USB TO UART port6. UART header: for connecting host boards like STM32/Arduino7. SMA antenna connector8. IPEX antenna connector9. Indicators:- RXD/TXD: UART RX/TX indicator- AUX: auxiliary indicator- PWR: power indicator10. UART selection jumpers- A: Control the LoRa module through USB TO UART- B: Control the LoRa module through Raspberry Pi- C: Access Raspberry Pi through USB TO UART11. LoRa mode selection jumpers- Short M0, short M1: Transmission mode- Short M0, open M1: Configuration mode- Open M0, short M1: WOR mode- Open M0, open M1: deep sleep modeSpecification1. RF module: SX12682. Frequency band: 410.125 ~ 493.125MHz3. Radio rate: 0.3kbps ~ 62.5kbps (programmable)4. Transmit power: 22.0dBm (10/13/17/22dBm programmable)5. Receive sensitivity: -147dBm (radio rate 2.4kbps)6. Power consumption: - Transmit current: 110mA (transient consumption)- Receive current: 11mA- Sleep current: 2uA (LoRa module software shutoff)7. Communication interface: UART (TTL level)8. Baudrate: 1200bps ~ 115200bps (9600bps by default)9. Packet length: 240 Byte (32/64/128/240 Byte programmable)10. Cache: 1000 Byte11. Experimental range: 5km (condition: cloudless and wild, altitude 2.5m, antenna gain 5dBi, radio rate 2.4kbps)12. Power supply: 5V13. Logic level: 3.3V/5V14. Operating temperature: -40~85 degree C15. Applications: Smart home, industrial sensors, building automation, smart meters, and more other IoT applications16. Dimensions: 7cm x 12cm x 2cm17. Weight: 69g18. Packing List:- SX1268 433MHz LoRa HAT x1- USB type A plug to micro plug cable x1- 433MHz antenna x1

Read more less

Features:1. Single-core ARM Cortex-A7 32-bit core, integrated NEON and FPU2. Built-in Rockchip's self-developed fourth-generation NPU, with high calculation accuracy and support for int4, int8, and int16 mixed quantization. The computing power of int8 is 0.5 TOPS, and int4 can reach 1.0 TOPS3. Built-in self-developed third-generation ISP3.2, supports 4 megapixels, and has various image enhancement and correction algorithms such as HDR, WDR, and multi-level noise reduction.4. Powerful encoding performance, supports intelligent encoding mode and adaptive throttling according to the scene, saving more than 50% bit rate than conventional CBR mode, making camera images higher-definition, smaller in size, and doubling the storage space5. The built-in RISC-V MCU supports low power consumption and fast startup, supports 250ms fast image capture and simultaneous loading of the AI model library, achieving "one second" face recognition6. Built-in 16-bit DRAM DDR2, capable of meeting the required memory bandwidth7. Integrated built-in POR, audio codec and MAC PHYProduct parameters:1. Processor: Cortex A7@1.2GHz + RISC-V2. NPU: 0.5TOPS, supports int4, int8, int163. ISP: Input 4M @30fps (maximum)4. Memory: 64MB DDR25. USB: USB 2.0 host/device6. Camera: MIPI CSI 2-lane7. GPIO: 25 × GPIO pins8. Ethernet port: 10/100M Ethernet controller and embedded PHY9. Default storage: SPI NAND FLASH (128MB)10. Product size: 72 x 21mm11. Weight: 13g, 11g

Read more less

Features:1. Single-core ARM Cortex-A7 32-bit core, integrated NEON and FPU2. Built-in Rockchip's self-developed fourth-generation NPU, with high calculation accuracy and support for int4, int8, and int16 mixed quantization. The computing power of int8 is 0.5 TOPS, and int4 can reach 1.0 TOPS3. Built-in self-developed third-generation ISP3.2, supports 4 megapixels, and has various image enhancement and correction algorithms such as HDR, WDR, and multi-level noise reduction.4. Powerful encoding performance, supports intelligent encoding mode and adaptive throttling according to the scene, saving more than 50% bit rate than conventional CBR mode, making camera images higher-definition, smaller in size, and doubling the storage space5. The built-in RISC-V MCU supports low power consumption and fast startup, supports 250ms fast image capture and simultaneous loading of the AI model library, achieving "one second" face recognition6. Built-in 16-bit DRAM DDR2, capable of meeting the required memory bandwidth7. Integrated built-in POR, audio codec and MAC PHYProduct parameters:1. Processor: Cortex A7@1.2GHz + RISC-V2. NPU: 0.5TOPS, supports int4, int8, int163. ISP: Input 4M @30fps (maximum)4. Memory: 64MB DDR25. USB: USB 2.0 host/device6. Camera: MIPI CSI 2-lane7. GPIO: 25 × GPIO pins8. Ethernet port: 10/100M Ethernet controller and embedded PHY9. Default storage: SPI NAND FLASH (128MB)10. Product size: 72 x 21mm11. Weight: 13g, 11g

Read more less

Features:1. Single-core ARM Cortex-A7 32-bit core, integrated NEON and FPU2. Built-in Rockchip's self-developed fourth-generation NPU, with high calculation accuracy and support for int4, int8, and int16 mixed quantization. The computing power of int8 is 0.5 TOPS, and int4 can reach 1.0 TOPS3. Built-in self-developed third-generation ISP3.2, supports 4 megapixels, and has various image enhancement and correction algorithms such as HDR, WDR, and multi-level noise reduction.4. Powerful encoding performance, supports intelligent encoding mode and adaptive throttling according to the scene, saving more than 50% bit rate than conventional CBR mode, making camera images higher-definition, smaller in size, and doubling the storage space5. The built-in RISC-V MCU supports low power consumption and fast startup, supports 250ms fast image capture and simultaneous loading of the AI model library, achieving "one second" face recognition6. Built-in 16-bit DRAM DDR2, capable of meeting the required memory bandwidth7. Integrated built-in POR, audio codec and MAC PHYProduct parameters:1. Processor: Cortex A7@1.2GHz + RISC-V2. NPU: 0.5TOPS, supports int4, int8, int163. ISP: Input 4M @30fps (maximum)4. Memory: 64MB DDR25. USB: USB 2.0 host/device6. Camera: MIPI CSI 2-lane7. GPIO: 24×GPIO pins8. Ethernet port: 10/100M Ethernet controller and embedded PHY9. Default storage: TF card (not included in delivery)10. Product size: 51 x 21mm11. Weight: 4g, 6g

Read more less

Features:1. Single-core ARM Cortex-A7 32-bit core, integrated NEON and FPU2. Built-in Rockchip's self-developed fourth-generation NPU, with high calculation accuracy and support for int4, int8, and int16 mixed quantization. The computing power of int8 is 0.5 TOPS, and int4 can reach 1.0 TOPS3. Built-in self-developed third-generation ISP3.2, supports 4 megapixels, and has various image enhancement and correction algorithms such as HDR, WDR, and multi-level noise reduction.4. Powerful encoding performance, supports intelligent encoding mode and adaptive throttling according to the scene, saving more than 50% bit rate than conventional CBR mode, making camera images higher-definition, smaller in size, and doubling the storage space5. The built-in RISC-V MCU supports low power consumption and fast startup, supports 250ms fast image capture and simultaneous loading of the AI model library, achieving "one second" face recognition6. Built-in 16-bit DRAM DDR2, capable of meeting the required memory bandwidth7. Integrated built-in POR, audio codec and MAC PHYProduct parameters:1. Processor: Cortex A7@1.2GHz + RISC-V2. NPU: 0.5TOPS, supports int4, int8, int163. ISP: Input 4M @30fps (maximum)4. Memory: 64MB DDR25. USB: USB 2.0 host/device6. Camera: MIPI CSI 2-lane7. GPIO: 24×GPIO pins8. Ethernet port: 10/100M Ethernet controller and embedded PHY9. Default storage: TF card (not included in delivery)10. Product size: 51 x 21mm11. Weight: 4g, 6g

Read more less

OverviewThe MCP23017 IO Expansion Board expands 2 signal pins as 16 I/O pins based on the I2C bus, up to 8 MCP23017 IO Expansion Board can be used at the same time, providing up to 128 I/O pins, it is compatible with both 3.3V and 5V levels.Features1. I2C controlled, expands 2 signal pins as 16 I/O pins2. I2C address configurable by shorting the A0/A1/A2 jumpers3. Provides two connector options: PH2.0 terminal and/or solder pads, allows multi I2C modules to be stacked4. Onboard voltage translator, compatible with 3.3V/5V level5. Comes with development resources and manual (examples for Raspberry Pi / micro:bit / Arduino / STM32)Specifications1. Operating voltage: 5V/3.3V2. Interface: I2C3. Interrupt pins: INTA, INTB4. Expansion I/Os: 165. Dimension: 38mm × 23mm6. Mounting hole size: 2.0mm

Read more less

Features1. Mini computer chassis, robust and dust-proof, nice looking 2. Tailored For Compute Module 4 IO Board: Make it easy to build your own Raspberry Pi CM4 mini PC 3. Break-out 40PIN GPIO Header: The standard 40 PIN GPIO header is still available, make it easy to connect sorts of HATs 4. Precise cut-out with clear label: Each cut-out Is completely aligned with the connector 5. Come with cooling fan, combined with airflow vent, better heat dissipation 6. Application: Binocular vision, PoE powered Raspberry Pi Projects, or other industrial contextPackage List1. Metal case (top and bottom) x 1 2. 40PIN GPIO adapter x 1 3. Fan-4010-PWM-12V x 1 4. Screwdriver x 1 5. Screws pack x 1

Read more less

Features1. Incorporates original chip Si3404, high-efficiency, high-safety, stable-performance 2. 10/100/1000Mbps auto-negotiation Ethernet port 3. 802.3af/at-compliant PoE (Power over Ethernet) standard 4. Isolated SMPS (Switching Mode Power Supply), effectively protecting the powered device 5. 5V DC output, suitable for powering Raspberry Pi and other small-scale network devices 6. Black dull-polish metal case, sturdy and rugged, higher protection level, better heat dissipationSpecifications1. Power Supply: Support 1/2(+); 3/6(-); 4/5(+); 7/8(-) powering 2. POE input voltage: 37V ~ 57V 3. Type-C output: 5V 2.5A (MAX) 4. Cable: Cat-5 UTP 5. Standard: IEEE 802.3 af/at PoE Ethernet 6. Data rate: 10/100/1000Mbps 7. LED indicator: PoE power input indicator 8. Size: 86 x 30 x 25mm (l x w x h) 9. Operation temperature: -40 degree C ~ 85 degree C

Read more less

Specifications1. Product: MG90S Servo2. Torque: 2.0kg/cm(4.8V), 2.8kg/cm(6V)3. Speed: 0.11s/60°(4.8V), 0.09s/60°(6V)4. Rotate angle: 180°5. Operating voltage: 4.8 ~ 6V6. Gear: metal7. Dead band: 5us8. Weight: 12.2g9. Dimension: 22.8mm × 12.2mm × 28.5mm

Read more less

1. Product: MG996R Servo2. Torque: 9kg/cm(4.8V), 11kg/cm(6V)3. Speed: 0.19s/60°(4.8V), 0.18s/60°(6V)4. Rotate angle: 180°5. Operating voltage: 4.8 ~ 6V6. Gear: metal7. Dead band: 5us8. Weight: 55g9. Dimension: 40.7mm × 19.7mm × 42.9mm

Read more less

1. Micro SD card slot2. Support SDIO and SPI interfaces3. 2.54mm pitch pinheaders

Read more less

Features1. Adopt new version CH343G chip. Compared with CH340G, it supports higher data rate (up to 6Mbps) and more serial port IO levels (5V / 3.3V / 2.5V / 1.8V) 2. Support Mac, Linux, Android, Windows 7/8/8.1/10/11 3. Onboard resettable Fuse and Transient Voltage Suppressor, anti-overcurrent and anti-overvoltage, anti-surge, anti-static, improve shock resistance, stable and safe communication performance 4. Onboard IO protection circuits, anti-surge, anti-static, stable and safe communication performance 5. Onboard 3.3V and 5V TTL level switch pins for selecting TTL communication level 6. Support 3.3V/5V output (the module is powered by USB, and the onboard jumper should be shorted to 3.3V or 5V accordingly) 7. Adopt double-sided black immersion gold process, which is durable and has a good lookIndictor Description1. PWR: Power indicator, turn on when the voltage is detected from USB interface 2. RXD: Receiving indicator, turn on when data is sent back from the device interface 3. TXD: Sending indicator, turn on when data is sent from USBPinouts Definition1. VCC: 5V or 3.3V output for external device (configured by jumper) 2. GND: Ground 3. TXD: Connects to MCU.RXD 4. RXD: Connects to MCU.TXD 5. RTS: Connects to MCU.CTS 6. CTS: Connects to MCU.RTSSpecifications1. Host interface: USB 2. Device interface: UART 3. Communication range: 50bps ~ 6Mbps 4. USB device interface: Micro USB 5. Protection: resettable Fuse, ESD protection 6. UART interface connector: 6-pin right-angle pinheader 7. Protection: IO protection diode

Read more less

1. USB: - USB 2.0 x 2 - USB 2.0 x 2 (via FFC connector) 2. GPIO: Raspberry Pi 40 PIN GPIO x 1 3. Header: M.2 slot x 1 4. HD media interface: HDMI x 2, 1x via FFC connector, support 4K 30fps output 5. DSI display: MIPI DSI x 1 (15pin 1.0mm FPC) 6. CSI camera: MIPI CSI-2 x 2 (15pin 1.0mm FPC) 7. Power input: 5V 8. FAN: 5V / 12V (no fan control) 9. RJ45 Ethernet: Gigabit Ethernet 10. CM4 slot: Suitable for all variants of Compute Module 4 11. SD card slot: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 12. Size: 85.0 x 56.0mm

Read more less

1. CM4 socket: For all variants of Compute Module 42. Networking: Gigabit Ethernet RJ45 connector3. Connector: M.2 M KEY, support communication module or NVME SSD4. USB: USB 2.0 Type A × Type 25. Display: LCD port6. Camera: MIPI CSI-2 camera port × 27. Video: HDMI port, support 4K 30fps output8. Fan header: allow speed adjustment, 5V9. Power input: 5V

Read more less

Specification1. USB: - USB 2.0 x 2 - USB 2.0 x 2 (via FFC connector) 2. GPIO: Raspberry Pi 40 PIN GPIO x 1 3. Header: M.2 slot x 1 4. HD media interface: HDMI x 2, 1x via FFC connector, support 4K 30fps output 5. DSI display: MIPI DSI x 1 (15pin 1.0mm FPC) 6. CSI camera: MIPI CSI-2 x 2 (15pin 1.0mm FPC) 7. Power input: 5V 8. FAN: 5V / 12V (no fan control) 9. RJ45 Ethernet: Gigabit Ethernet 10. CM4 slot: Suitable for all variants of Compute Module 4 11. SD card slot: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 12. Size: 85.0 x 56.0mmPackage List1. CM4-IO-BASE-B x 1 2. Metal case (top and bottom) x 1 3. Fan-4010-PWM-5V x 1 4. Screwdriver x 1 5. Screws pack x 1 6. 5V 3A USB-C power adapter x 1

Read more less

Specification1. USB: - USB 2.0 x 2 - USB 2.0 x 2 (via FFC connector) 2. GPIO: Raspberry Pi 40 PIN GPIO x 1 3. Header: M.2 slot x 1 4. HD media interface: HDMI x 2, 1x via FFC connector, support 4K 30fps output 5. DSI display: MIPI DSI x 1 (15pin 1.0mm FPC) 6. CSI camera: MIPI CSI-2 x 2 (15pin 1.0mm FPC) 7. Power input: 5V 8. FAN: 5V / 12V (no fan control) 9. RJ45 Ethernet: Gigabit Ethernet 10. CM4 slot: Suitable for all variants of Compute Module 4 11. SD card slot: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 12. Size: 85.0 x 56.0mmPackage List1. CM4-IO-BASE-B x 1 2. Metal case (top and bottom) x 1 3. Fan-4010-PWM-5V x 1 4. Screwdriver x 1 5. Screws pack x 1 6. 5V 3A USB-C power adapter x 1

Read more less

Specification1. USB: - USB 2.0 x 2 - USB 2.0 x 2 (via FFC connector) 2. GPIO: Raspberry Pi 40 PIN GPIO x 1 3. Header: M.2 slot x 1 4. HD media interface: HDMI x 2, 1x via FFC connector, support 4K 30fps output 5. DSI display: MIPI DSI x 1 (15pin 1.0mm FPC) 6. CSI camera: MIPI CSI-2 x 2 (15pin 1.0mm FPC) 7. Power input: 5V 8. FAN: 5V / 12V (no fan control) 9. RJ45 Ethernet: Gigabit Ethernet 10. CM4 slot: Suitable for all variants of Compute Module 4 11. SD card slot: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 12. Size: 85.0 x 56.0mmPackage List1. CM4-IO-BASE-A x 1 2. Metal case (top and bottom) x 1 3. Fan-4010-PWM-5V x 1 4. Screwdriver x 1 5. Screws pack x 1 6. 5V 3A USB-C power adapter x 1

Read more less

Specification1. USB: - USB 2.0 x 2 - USB 2.0 x 2 (via FFC connector) 2. GPIO: Raspberry Pi 40 PIN GPIO x 1 3. Header: M.2 slot x 1 4. HD media interface: HDMI x 2, 1x via FFC connector, support 4K 30fps output 5. DSI display: MIPI DSI x 1 (15pin 1.0mm FPC) 6. CSI camera: MIPI CSI-2 x 2 (15pin 1.0mm FPC) 7. Power input: 5V 8. FAN: 5V / 12V (no fan control) 9. RJ45 Ethernet: Gigabit Ethernet 10. CM4 slot: Suitable for all variants of Compute Module 4 11. SD card slot: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants 12. Size: 85.0 x 56.0mmPackage List1. CM4-IO-BASE-A x 1 2. Metal case (top and bottom) x 1 3. Fan-4010-PWM-5V x 1 4. Screwdriver x 1 5. Screws pack x 1 6. 5V 3A USB-C power adapter x 1

Read more less

1. Only compatible with Raspberry Pi 4B2. ABS material shell and two transparent acrylic side panels3. A 0.96-inch OLED screen has been installed on the shell, 28 x 64 pixels, and the default I2C address: 0x3C4. M.2 SATA SSD 2280/2260/2240 mass storage adapter board, supports M.2 SATA SSD up to 2TB5. Note: Raspberry Pi 4B is not included

Read more less

Features1. Adopt new version CH343G chip. Compared with CH340G, it supports higher data rate (up to 6Mbps) and more serial port IO levels (5V / 3.3V / 2.5V / 1.8V) 2. Support Mac, Linux, Android, Windows 7/8/8.1/10/11 3. Onboard resettable Fuse and Transient Voltage Suppressor, anti-overcurrent and anti-overvoltage, anti-surge, anti-static, improve shock resistance, stable and safe communication performance 4. Onboard IO protection circuits, anti-surge, anti-static, stable and safe communication performance 5. Onboard 3.3V and 5V TTL level switch pins for selecting TTL communication level 6. Support 3.3V/5V output (the module is powered by USB, and the onboard jumper should be shorted to 3.3V or 5V accordingly) 7. Adopt double-sided black immersion gold process, which is durable and has a good lookIndictor Description1. PWR: Power indicator, turn on when the voltage is detected from USB interface 2. RXD: Receiving indicator, turn on when data is sent back from the device interface 3. TXD: Sending indicator, turn on when data is sent from USBPinouts Definition1. VCC: 5V or 3.3V output for external device (configured by jumper) 2. GND: Ground 3. TXD: Connects to MCU.RXD 4. RXD: Connects to MCU.TXD 5. RTS: Connects to MCU.CTS 6. CTS: Connects to MCU.RTSSpecifications1. Host interface: USB 2. Device interface: UART 3. Communication range: 50bps ~ 6Mbps 4. USB device interface: Mini USB 5. Protection: resettable Fuse, ESD protection 6. UART interface connector: 6-pin right-angle pinheader 7. Protection: IO protection diode

Read more less

FeaturesThe Compute Module PoE Board is a development board that you can plug a Raspberry Pi Compute Module into, and make use of the resources of Pi more flexibly. With the PoE (Power over Ethernet) feature, and versatile onboard peripheral interfaces, it is suitable for evaluating the Raspberry Pi compute module, also is an ideal choice for end products. 1. Raspberry Pi GPIO header, for connecting sorts of Raspberry Pi HATs. 2. 10/100M auto-negotiation Ethernet port, with PoE enabled. 3. 4 x USB ports, which allows connecting more USB devices. 4. 2 x CSI camera interfaces. 5. Onboard HDMI / DSI interfaces for connecting displays. 6. Onboard USB TO UART, for serial debugging. 7. Cooling fan interface, autorun on power-up OR controlled by IO pins. 8. Adopt isolated SMPS (Switching mode power supply).Specifications1. Power supply: Micro USB port / PoE Ethernet port 2. PoE power input: 37V ~ 57V DC in 3. PoE power output: 5V 2.5A DC out 4. Operating Temperature: -25 degree C ~ 80 degree C 5. Network standard: 802.3af PoE standard 6. Dimensions: 144mm x 88mm 7. Mounting hole size: 3.2mm

Read more less

FeaturesThe Compute Module PoE Board is a development board that you can plug a Raspberry Pi Compute Module into, and make use of the resources of Pi more flexibly. With the PoE (Power over Ethernet) feature, and versatile onboard peripheral interfaces, it is suitable for evaluating the Raspberry Pi compute module, also is an ideal choice for end products. 1. Raspberry Pi GPIO header, for connecting sorts of Raspberry Pi HATs. 2. 10/100M auto-negotiation Ethernet port, with PoE enabled. 3. 4 x USB ports, which allows connecting more USB devices. 4. 2 x CSI camera interfaces. 5. Onboard HDMI / DSI interfaces for connecting displays. 6. Onboard USB TO UART, for serial debugging. 7. Cooling fan interface, autorun on power-up OR controlled by IO pins. 8. Adopt isolated SMPS (Switching mode power supply).Specifications1. Power supply: Micro USB port / PoE Ethernet port 2. PoE power input: 37V ~ 57V DC in 3. PoE power output: 5V 2.5A DC out 4. Operating Temperature: -25 degree C ~ 80 degree C 5. Network standard: 802.3af PoE standard 6. Dimensions: 144mm x 88mm 7. Mounting hole size: 3.2mm

Read more less

FeaturesThe Compute Module PoE Board is a development board that you can plug a Raspberry Pi Compute Module into, and make use of the resources of Pi more flexibly. With the PoE (Power over Ethernet) feature, and versatile onboard peripheral interfaces, it is suitable for evaluating the Raspberry Pi compute module, also is an ideal choice for end products. 1. Raspberry Pi GPIO header, for connecting sorts of Raspberry Pi HATs. 2. 10/100M auto-negotiation Ethernet port, with PoE enabled. 3. 4 x USB ports, which allows connecting more USB devices. 4. 2 x CSI camera interfaces. 5. Onboard HDMI / DSI interfaces for connecting displays. 6. Onboard USB TO UART, for serial debugging. 7. Cooling fan interface, autorun on power-up OR controlled by IO pins. 8. Adopt isolated SMPS (Switching mode power supply).Specifications1. Power supply: Micro USB port / PoE Ethernet port 2. PoE power input: 37V ~ 57V DC in 3. PoE power output: 5V 2.5A DC out 4. Operating Temperature: -25 degree C ~ 80 degree C 5. Network standard: 802.3af PoE standard 6. Dimensions: 144mm x 88mm 7. Mounting hole size: 3.2mm

Read more less

Features1. 13.3inch IPS screen,1920x1080 high resolution 2. 6H hardness toughened glass capacitive touch panel, 10-points touch 3. Mini-computer powered by Raspberry Pi CM4 4. Powerful controller: Raspberry Pi CM4; Not just a simple display, with powerful Raspberry Pi CM4 (CM4104000) inside 5. Multiple OS Support: Raspberry Pi OS / Ubuntu / Kali / WIN10 IoT / Retropie 6. Multi languages OSD menu, for power management, brightness / contrast adjustment, etc. 7. With USB/ETH port, 3.5mm audio jack, embedded Hi-Fi speaker 8. Could be a Raspberry Pi tablet: Having fun with this Raspberry Pi tablet, watch movies, listen music 9. Also a desktop mini-computer: Transform to a mini-computer in 1s for study/work, just connect wireless mouse and Keyboard 10. High Speed Networking: Support gigabit ethernet and 2.4Ghz/5Ghz dual-band WiFi high speed internet connection, support Bluetooth5.0Package List1. 13.3 inch Pi-Pad C4 x 1 2. Back stand x 1 3. 2.4G/5G WiFi antenna x 1 4. 12V 1A power supply x 1 5. Screwdriver x 1 6. CM4104000 x 1 7. 16GB Micro SD card x 1 8. Card reader x 1

Read more less

Features1. 13.3inch IPS screen,1920x1080 high resolution 2. 6H hardness toughened glass capacitive touch panel, 10-points touch 3. Mini-computer powered by Raspberry Pi CM4 4. Powerful controller: Raspberry Pi CM4; Not just a simple display, with powerful Raspberry Pi CM4 (CM4104000) inside 5. Multiple OS Support: Raspberry Pi OS / Ubuntu / Kali / WIN10 IoT / Retropie 6. Multi languages OSD menu, for power management, brightness / contrast adjustment, etc. 7. With USB/ETH port, 3.5mm audio jack, embedded Hi-Fi speaker 8. Could be a Raspberry Pi tablet: Having fun with this Raspberry Pi tablet, watch movies, listen music 9. Also a desktop mini-computer: Transform to a mini-computer in 1s for study/work, just connect wireless mouse and Keyboard 10. High Speed Networking: Support gigabit ethernet and 2.4Ghz/5Ghz dual-band WiFi high speed internet connection, support Bluetooth5.0Package List1. 13.3 inch Pi-Pad C4 x 1 2. Back stand x 1 3. 2.4G/5G WiFi antenna x 1 4. 12V 1A power supply x 1 5. Screwdriver x 1 6. CM4104000 x 1 7. 16GB Micro SD card x 1 8. Card reader x 1

Read more less

Features1. 13.3inch IPS screen,1920x1080 high resolution 2. 6H hardness toughened glass capacitive touch panel, 10-points touch 3. Mini-computer powered by Raspberry Pi CM4 4. Powerful controller: Raspberry Pi CM4; Not just a simple display, with powerful Raspberry Pi CM4 (CM4104000) inside 5. Multiple OS Support: Raspberry Pi OS / Ubuntu / Kali / WIN10 IoT / Retropie 6. Multi languages OSD menu, for power management, brightness / contrast adjustment, etc. 7. With USB/ETH port, 3.5mm audio jack, embedded Hi-Fi speaker 8. Could be a Raspberry Pi tablet: Having fun with this Raspberry Pi tablet, watch movies, listen music 9. Also a desktop mini-computer: Transform to a mini-computer in 1s for study/work, just connect wireless mouse and Keyboard 10. High Speed Networking: Support gigabit ethernet and 2.4Ghz/5Ghz dual-band WiFi high speed internet connection, support Bluetooth5.0Package List1. 13.3 inch Pi-Pad C4 x 1 2. Back stand x 1 3. 2.4G/5G WiFi antenna x 1 4. 12V 1A power supply x 1 5. Screwdriver x 1 6. CM4104000 x 1 7. 16GB Micro SD card x 1 8. Card reader x 1

Read more less

Features1.4 in 1, suit for DIYIRM, infrared receiver moduleTemperature SensorJoystickBuzzer2.Compatible with expansion boards like DVK5123.Connections are controlled by jumpers

Read more less

Overview1. Fork-like design, make it easy to insert into the soil2. Output voltage boosts along with the soil moisture level increasesSpecifications1. Detection depth: 38mm2. Power: 2.0V ~ 5.0V3. Dimension: 20.0mm * 51.0mm4. Mounting holes size: 2.0mmApplications1. Auto watering system2. Flowerpot soil moisture detection3. Auto pouring systemHow to UseIn the case of working with a MCU:1. VCC: 3.3V ~ 5.5V2. GND: GND3. DOUT: MCU.IOPackage Contents1. Moisture Sensor x12. 3-pin custom connector jumper wire x1

Read more less

1. High efficiency, outdoor waterproof, self-contained bracket, easy to install2. Connect the power management module or other control boards that support 5.5V solar panel charging or power supply, compatible with solar power managers3. Working voltage: 5.5v4. Working current: 1000mA5. Open circuit voltage: 7.2v6. Short circuit current: 1090mA7. Output interface: micro USB, USB/Type-C8. Solar power: 6w9. Application examples: It can be directly connected to low-power outdoor smart electronic devices to support 5.5V solar panels through USB ports, such as monitoring equipment, doorbells, fans, emergency lights, etc.10. Cable length: 3 meters11. Size: 225x195x17.6mminstallation steps:1. Install the stand with the screws included in the package2. Fix the solar panel on the bracket3. Adjust the angle of the panel by rotating the knob on the stand to maximize sunlight absorption

Read more less

Overview1. Sensitive for benzene, alcohol, smoke2. Output voltage boosts along with the concentration of the measured gases increases3. Fast response and recovery4. Adjustable sensitivity5. Signal output indicatorSpecifications1. Power: 2.5V ~ 5.0V2. Dimension: 40.0mm * 21.0mm3. Mounting holes size: 2.0mmApplicationsAir quality monitorHow to UseIn the case of working with a MCU:1. VCC: 2.5V ~ 5.0V2. GND: Power supply ground3. AOUT: MCU.IO (analog output)4. DOUT: MCU.IO (digital output)Package Contents1. MQ-135 Gas Sensor x12. 4-pin custom connector jumper wire x1

Read more less

Overview1. Sensitive for LPG, propane, hydrogen2. Output voltage boosts along with the concentration of the measured gases increases3. Fast response and recovery4. Features boost circuit5. Adjustable sensitivity6. Signal output indicatorSpecifications1. Power: 2.5V ~ 5.0V2. Dimension: 40.0mm * 21.0mm3. Mounting holes size: 2.0mmApplicationsGas leakage detectorHow to UseIn the case of working with a MCU:1. VCC: 2.5V ~ 5.0V2. GND: Power supply ground3. AOUT: MCU.IO (analog output)4. DOUT: MCU.IO (digital output)Package Contents1. MQ-2 Gas Sensor x12. 4-pin custom connector jumper wire x1

Read more less