TB6600 Upgrade Version 4.0A 42V DC 32 Subdivision 42/57/86 Stepper Motor Driver


1. 9V-40V DC power supply
2. H-bridge bipolar constant phase current driver
3. Up to 4.0A eight output current selectable
4. 6 sub-division modes up to 32 sub-divisions selectable
5. Input signal high-speed optical isolation
6. Standard common positive single pulse interface
7. Offline hold function
8. Semi-enclosed enclosure for more demanding environments
9. Provide energy-saving semi-automatic current lockout function
10. Built-in temperature protection and over-current protection
11. Applicable stepping motor: 42, 57, 86 type 2-phase 4-phase (4 wire 6 wire 8 wire)
12. Weight: about 201g

Wiring terminal definition description:
-Signal input terminal:
1. CP+: pulse signal input positive terminal
2. CP-: pulse signal input negative terminal
3. DIR+: motor forward and reverse control positive terminal
4. DIR-: motor forward and reverse control negative terminal
5. EN+: motor offline control positive terminal
6. EN-: motor offline control negative terminal

-Motor winding connection:
1. A+: connect motor winding A+ phase
2. A-: connect to motor winding phase A-
3. B+: connect motor winding B+ phase
4. B-: connect motor winding B- phase

-Connections for operating voltage:
1. VCC: DC power supply positive ( note: 10V <VCC <42V)
2. GND: DC power supply negative

-Input signal interface has two connection methods: users can use the common anode connection method or common cathode connection method according to the need
1. Common anode connection: connect CP+, DIR+ and EN+ to the power supply of the control system, if the power supply is +5V, then it can be connected directly, if the power supply is greater than +5V, then it is necessary to add another external current limiting resistor R, to ensure that the internal optical coupler of the driver can provide a driving current of 8-15mA. pulse input signal through the CP-access; at this time, DIR-, EN- in the low level of active
2. Common cathode connection: connect CP-, DIR- and EN- to the ground of the control system (SGND, isolated from the power supply ground); the +5V pulse input signal is added through CP+; at this time, DIR+ and EN+ are active at high level. the value of current limiting resistor R is the same as that of common anode connection
3. Note: the EN terminal may not be connected, the motor rotor is in a free state (offline state) when EN is valid, then you can manually rotate the motor rotor to do the adjustment that suits you. after the manual adjustment is completed, set EN to invalid state to continue the automatic control


Specification:
Package Weight
One Package Weight 0.14kgs / 0.32lb
One Package Size 12cm * 10cm * 5cm / 4.72inch * 3.94inch * 1.97inch
Qty per Carton 160
Carton Weight 25.00kgs / 55.12lb
Carton Size 55cm * 31cm * 39cm / 21.65inch * 12.2inch * 15.35inch
Loading Container 20GP: 401 cartons * 160 pcs = 64160 pcs
40HQ: 930 cartons * 160 pcs = 148800 pcs

TB6600 Upgrade Version 4.0A 42V DC 32 Subdivision 42/57/86 Stepper Motor Driver

Product form

SKU: TBD06052844

  • In stock (Processing Time 1 - 72 hours)

61,26 lei

    • Guaranteed secure & safe checkout.

    Icon for truckShipping Methods

    To find out all available shipping methods, and the exact delivery time add the product to the cart and verify it using our shipping calculator.

    Icon for 24_hour_clockOrder Processing Time

    All orders are shipped within a maximum of 72 hours from the order's arrival.

    Icon for coinMoney Back Guarantee

    Garmade Money Back Guarantee- Get the item you ordered or your money back, it's that simple.

    Icon for image_placeholderMismatched Product

    Product doesn't match the description? Contact us within 31 days after you receive it!

    Icon for mobile_paymentRefunds

    In case of cancellation, money will be refunded to your account within 14 days.

    Description


    1. 9V-40V DC power supply
    2. H-bridge bipolar constant phase current driver
    3. Up to 4.0A eight output current selectable
    4. 6 sub-division modes up to 32 sub-divisions selectable
    5. Input signal high-speed optical isolation
    6. Standard common positive single pulse interface
    7. Offline hold function
    8. Semi-enclosed enclosure for more demanding environments
    9. Provide energy-saving semi-automatic current lockout function
    10. Built-in temperature protection and over-current protection
    11. Applicable stepping motor: 42, 57, 86 type 2-phase 4-phase (4 wire 6 wire 8 wire)
    12. Weight: about 201g

    Wiring terminal definition description:
    -Signal input terminal:
    1. CP+: pulse signal input positive terminal
    2. CP-: pulse signal input negative terminal
    3. DIR+: motor forward and reverse control positive terminal
    4. DIR-: motor forward and reverse control negative terminal
    5. EN+: motor offline control positive terminal
    6. EN-: motor offline control negative terminal

    -Motor winding connection:
    1. A+: connect motor winding A+ phase
    2. A-: connect to motor winding phase A-
    3. B+: connect motor winding B+ phase
    4. B-: connect motor winding B- phase

    -Connections for operating voltage:
    1. VCC: DC power supply positive ( note: 10V <VCC <42V)
    2. GND: DC power supply negative

    -Input signal interface has two connection methods: users can use the common anode connection method or common cathode connection method according to the need
    1. Common anode connection: connect CP+, DIR+ and EN+ to the power supply of the control system, if the power supply is +5V, then it can be connected directly, if the power supply is greater than +5V, then it is necessary to add another external current limiting resistor R, to ensure that the internal optical coupler of the driver can provide a driving current of 8-15mA. pulse input signal through the CP-access; at this time, DIR-, EN- in the low level of active
    2. Common cathode connection: connect CP-, DIR- and EN- to the ground of the control system (SGND, isolated from the power supply ground); the +5V pulse input signal is added through CP+; at this time, DIR+ and EN+ are active at high level. the value of current limiting resistor R is the same as that of common anode connection
    3. Note: the EN terminal may not be connected, the motor rotor is in a free state (offline state) when EN is valid, then you can manually rotate the motor rotor to do the adjustment that suits you. after the manual adjustment is completed, set EN to invalid state to continue the automatic control


    Specification:
    Package Weight
    One Package Weight 0.14kgs / 0.32lb
    One Package Size 12cm * 10cm * 5cm / 4.72inch * 3.94inch * 1.97inch
    Qty per Carton 160
    Carton Weight 25.00kgs / 55.12lb
    Carton Size 55cm * 31cm * 39cm / 21.65inch * 12.2inch * 15.35inch
    Loading Container 20GP: 401 cartons * 160 pcs = 64160 pcs
    40HQ: 930 cartons * 160 pcs = 148800 pcs

    Additional Information

    Icon for truckShipping Info

    IMPORTANT INFO - PLEASE CHECK BEFORE ORDERING.



      Estimated transit time and postage fee depends on the method you choose at checkout. Please add the desired product to the cart and there you will be able to see all this information.

      Complete and right address is the guarantee of fast and efficient delivery, so please kindly recheck it when you place an order.

      In order to ensure a fast and efficient delivery, we need to have the method of contact with you. Email and Phone Number is a very important detail and must be accurate. All orders with an incorrect email or phone number will be canceled immediately.

      We strive to dispatch all orders within 72 hours of placing your order. But sometimes if the order is big or the products are more sophisticated, it can take a little longer. As soon as we dispatched it, you will receive a confirmation email along with a tracking number.

      Please be aware that sometimes due to unclear address, hard to access, no answer at address, the package can be kept at your local post office for collection. In this case you will be informed by the delivery company and by us. Please also monitor the tracking number.

      For European Union Countries:
    - If your order is less than 150€ excluding shipping costs, then the Taxes are already included in the price. This means that there will be NO extra charge upon delivery.
    - If your order is more than 150€, you will NOT be charged Taxes at the checkout, and you will have to pay upon delivery based on your local VAT rate.

     

    Icon for reviewReviews

    Customer Reviews

    Be the first to write a review
    0%
    (0)
    0%
    (0)
    0%
    (0)
    0%
    (0)
    0%
    (0)

    Login

    Forgot your password?

    Don't have an account yet?
    Create account