Consumer Electronics

1. Humidity range: 0-1002. Material physical properties: semiconductor3. Output signal: digital4. Working voltage: 3.3V-5V5. Size: 3cm * 1.6cm6. Features: LM393 chip, stable operation, fixed bolt holes for easy installation, dual output mode of the module, simple digital output, more accurate analog output, and adjustable sensitivity

Read more less

Features1. Bluetooth+AUX audio input, dual-channel stereo output, just a little sound distortion. 2. You can directly adjust the treble and bass. 3. AMP module has AM interference suppression function, shielding cover power inductor, low noise front stage operational amplifier, you will enjoy a more excellent sound quality experience. 4. Audio amplifier board with over-voltage protection, under-voltage protection, over-heat protection, short-circuit protection. 5. The illustration of each interface is printed on the protective plate, making it easy to install and use even without instructions. Use occasion: This 50W+50W dual-channel Bluetooth audio amplifier board is widely use indoor and outdoor, such as family, party, bar, band, concert, carnival etc.Specification1. Material: ABS plastic 2. Bluetooth version: 5.0 3. Input Mode: Bluetooth / AUX 4. Power Output: 50W x 2 5. Channel: 2 6. Chip: TPA3116D2 (AM interference suppression function) 7. Bluetooth transmission distance: 10m (without occlusion) 8. Adapter speaker: 15-100W, 4 ohm s- 8 ohms 9. Signal to noise ratio: Greater than 90dB 10. Adapted power supply: DC 9-24V/ above 2A 11. Output Power: - 15W x 2 at 12V, 8 ohms - 20W x 2 at 19V, 8 ohms - 30W x 2 at 12V, 4 ohms - 30W x 2 at 24V, 8 ohms - 40W x 2 at 19V, 4 ohms - 50W x 2 at 24V, 4 ohms 12. Size: 110 x 70 x 21mm

Read more less

Technical specifications:1. Support sampling rate (KHz): 8/11.025/12/16/22.05/24/32/44.1/482. 24-bit DAC output, dynamic range support: 90dB, signal-to-noise ratio support: 85dB3. Fully support FAT16, FAT32 file system, support 32G TF card, support 32G U disk, 64M byte NORFLASH4. A variety of control modes are available. IO control mode, serial port mode, AD button control mode5. The broadcast language insertion function, you can pause the background music that is playing. After the ad is played, return to the background sound to continue playing6. The audio data is sorted by folder, supporting 100 folders at most, and 255 tracks can be assigned to every folder7. 30 levels of volume adjustable, 6 levels of EQ adjustableApplication range:1. Car navigation voice broadcast2. Highway transportation inspection, toll station voice prompt3. Voice prompts for safety inspections at railway stations and bus stations4. Voice prompts for power, communications, and financial business offices5. Voice prompts for vehicle entry and exit channel verification6. Voice prompts for border inspection channels7. Multi-channel voice alarm or equipment operation guidance voice8. Voice notice for safe driving of electric sightseeing cars9. Automatic alarm for mechanical and electrical equipment failure10. Fire alarm prompt11. Automatic broadcast equipment, regular broadcastProduct description:1. Can be directly connected to speakers2. The module can be used alone with the power supply battery, speakers, and buttons, or can be controlled through the serial port, as a module of UNO or any single-chip microcomputer with a serial port3. The module itself perfectly integrates the hard decoding of MP3, WAV and WMA. At the same time, the software supports TF card driver, supports FAT16, FAT32 file system4. Through simple serial port commands, you can complete the functions of playing the specified music and how to play the music. There is no need for cumbersome underlying operations, easy to use, stable and reliable

Read more less

1. Voltage: DC 2.5-5.5V. 2. Output Power: 3W + 3W (at 4 ohm). 3. Noise ratio: 90dB. 4. Efficiency: more than 90 percent. 5. 2 channels 3W amplifier with PAM8403. 6. Output is CMOS BTL driver. 7. Cannot change any component parameters to protect IC. 8. The board can also be powered by 5V USB power supply or 4 x 1.5V battery. 9. It is perfect for MP3, MP4 and notebook.

Read more less

1. The USB to RS232 converter cable provides simple and easy way to connect universal serial bus (USB) and serial port interface. 2. Via this adapter cable, you can utilize the peripheral with serial port interface in an easy-use environment such as plug the play hot swap function. 3. This adapter is designed for ideal connections to cellular phone, digital camera, modems or ISDN terminal adapter with max. 1 Mbps data transfer rate. 4. Application: Convert USB port to RS232 serial port.

Read more less

1. Double decks for 4pcs AA batteries. 2. Easy to connect to other devices with 18cm cable. 3. Able to make 6V battery pack from alkaline cells. 4. Perfect external power source for Arduino system.

Read more less

1. Resistance range: 100 ohm - 10K ohm. 2. It is widely used to adjust timer, speed, temperature. 3. For MCU experiment.

Read more less

1. Low standby current.through the I2C bus serial input / output. 2. PCF8591 by 3 hardware address pins addressing. Sampling rate PCF8591 I2C bus rate decided. 3. 4 analog inputs programmable as single-ended or differential inputs.Automatic incremental channel selection 4. PCF8591 analog voltage range from VSS to VDD.PCF8591 built-in track and hold circuit. 5. 8-bit successive approximation A / D converter. through an analog output DAC gain. module chip using PCF8951 . 6. Working Voltage : 2.5-6V

Read more less

1. Works with official Arduino boards 2. This is an I2C controlled PWM driver board with a built-in clock 3. You can use 3.3V MCU to control and drive the output up to 6V 4. 6 address select pins allow you to connect 62 driver boards to one I2C bus, total 992 channels of PWM output 5. About 1.6KHz frequency modulation PWM output 6. PCA9685 chip is at the center of the board 7. With power input terminal 8. With green power indicator light 9. Convenient to insert total 16 servos at the same time 10. With reverse polarity protection for input 11. Cascade design 12. Put a bulky capacitor on the V+ line 13. Put 220 ohm resistance components onto all PWM output lines

Read more less

1. Chip: MAX3232CSE 2. Voltage range: 3 v to 5 v 3. The highest baud rate : not recommended More than 120 KBPS 4. A converter board for electrical levels

Read more less

1. Onboard complex frequency decoder chip MT8870 2. Onboard voice input interface 3. Onboard five LED indicators for easy viewing output state 4. Basic pins of the chip have been drawn 5. For Arduino, Raspberry Pi, ARM MCU and more

Read more less

1. Material: PCB 2. Working voltage: 3.3 or 5V 3. On-board AMS1117 - 3.3 chip 4. Wireless module operating voltage is 3.3V, while the ordinary 51 single-chip is 5V 5. Connect wireless module with 51 single-chip system board 6. It is for NRF24L01 + wireless module 7. This is a simple socket board which is for NRF24L01 wireless module

Read more less

1. Used as a square wave signal generator, which produces square wave signals for experimental development. 2. Used to generate square wave signals that can drive the stepper motor . 3. The adjustable pulse is generated for use of MCU. 4. Generate adjustable pulses to control the related circuits. 5. NOTE :When using a jumper cap to change the frequency, please cut off the power first, wait for the jump cap and then reconnect.

Read more less

1. Dielectric strength: withstand 750 V (50 Hz AC RMS) for 1 minute, without breaking, flying fox phenomenon 2. Rated power: 2W 3. Small size, easy to carry

Read more less

Main Features: 1. The board uses a high-performance digital amplifier TDA8932 chip 2. Small size, high efficiency, high power, good sound quality, without additional installation of radiator 3. Suitable for the transformation of active speaker, product development, and other audio application Specification: 1. Material: PCB 2. Chipset: TDA8932 3. Operating voltage: single DC 10 - 30V ( 24V recommended voltage ) 4. Current: above 2A 5. Power output: 35W 6. Speaker impedance: 4 - 8 ohm ( 8 ohm is the best ) 7. Circuit configuration: mono BTL output

Read more less

This is 28YBJ-48 DC 5V 4 phase 5 wire stepper motor with ULN2003 driver board, 5-wire phase can drive ordinary uln2003 chip can also be connected as phase 2 may be supporting the development board, direct plug, easy to use stepper motor used in the development boardMotor1. Diameter: 28mm2. Voltage: 5V3. Step angle: 5.625 x 1/644. Reduction ratio: 1/64ULN2003 driver board1. A, B, C, D LED indication Four-phase stepper motor work status2. Size: 31x35mmPackage included1. 1 x ULN2003 driver board2. 1 x 28BYJ-48 stepper motor

Read more less

1. Metal gear, stable transmission and wear-resistant2. Pure copper motor, effectively insulates dust and high temperature3. 304 stainless steel folding, high-precision gear box4. Features: Durable, dust-proof, anti-skid, high temperature resistance, abrasion resistance5. Rated voltage: 6/12v6. Application: electronic locks, smart cars, robots, cameras, etc.7. Size: about 14x17x35mm8. Material: 304 stainless steel

Read more less

1. Metal gear, stable transmission and wear-resistant2. Pure copper motor, effectively insulates dust and high temperature3. 304 stainless steel folding, high-precision gear box4. Features: Durable, dust-proof, anti-skid, high temperature resistance, abrasion resistance5. Rated voltage: 6/12v6. Application: electronic locks, smart cars, robots, cameras, etc.7. Size: about 14x17x35mm8. Material: 304 stainless steel

Read more less

1. Metal gear, stable transmission and wear-resistant2. Pure copper motor, effectively insulates dust and high temperature3. 304 stainless steel folding, high-precision gear box4. Features: Durable, dust-proof, anti-skid, high temperature resistance, abrasion resistance5. Rated voltage: 6/12v6. Application: electronic locks, smart cars, robots, cameras, etc.7. Size: about 14x17x35mm8. Material: 304 stainless steel

Read more less

1. Metal gear, stable transmission and wear-resistant2. Pure copper motor, effectively insulates dust and high temperature3. 304 stainless steel folding, high-precision gear box4. Features: Durable, dust-proof, anti-skid, high temperature resistance, abrasion resistance5. Rated voltage: 6/12v6. Application: electronic locks, smart cars, robots, cameras, etc.7. Size: about 14x17x35mm8. Material: 304 stainless steel

Read more less

1. Metal gear, stable transmission and wear-resistant2. Pure copper motor, effectively insulates dust and high temperature3. 304 stainless steel folding, high-precision gear box4. Features: Durable, dust-proof, anti-skid, high temperature resistance, abrasion resistance5. Rated voltage: 6/12v6. Application: electronic locks, smart cars, robots, cameras, etc.7. Size: about 14x17x35mm8. Material: 304 stainless steel

Read more less

1. Metal gear, stable transmission and wear-resistant2. Pure copper motor, effectively insulates dust and high temperature3. 304 stainless steel folding, high-precision gear box4. Features: Durable, dust-proof, anti-skid, high temperature resistance, abrasion resistance5. Rated voltage: 6/12v6. Application: electronic locks, smart cars, robots, cameras, etc.7. Size: about 14x17x35mm8. Material: 304 stainless steel

Read more less

1. 15A current overload protection switch, real-time monitoring of electricity safety 2. Low-voltage start-up is more practical, with a trigger module to achieve 10V start-up, and no trigger device 60V start-up voltage is as low as possible 3. Input voltage: AC 220V 4. Output voltage: 0-220V adjustable (Voltmeter does not work when the output voltage is lower than 5V) 5. Limit power: 4000W (suitable for 1000W-2000W motor load) 6. Voltage adjustment range: 0-220V steplessly adjustable (under load conditions), step down to 0V, step up from 10V 7. Rated current: 9A 8. Limit current: 18A

Read more less

1. 5V relay module2. It can be used as a single-chip development board module, and can be used as a home appliance control3. 5V-12V TTL control signal4. Control DC or AC signal, can control 220V AC load5. There is a normally open and a normally closed contact6. Has a power indicator7. There is a control indicator light, which is bright when closing, but not bright when disconnecting8. Transistor drive increases the relay coil, and the control pin is high impedance9. The control pin has a pull-down circuit to prevent the false action of the floating relay

Read more less

1. Product weight: 230g 2. Product material: ABS / metal material 3. Applicable models (scene): GM,SUV off-road pickup truck 4. UPC: 707427709829 5. Includes accessories 1 x relay bracket, 41 pins

Read more less

Type:Voltage Regulator1. Power supply current: 12A 2. Power supply voltage: 40v3. Power: Standard4. Number of pins: Standard5. Use: Instrument6. Package: DC-DC step-down adjustable constant voltage constant current 10A7. Application area: Household appliances8. Packing: boxed9. Weight: 67.2g10. Size: 47 x 65mm

Read more less

1. 5-ch ITR20001/T infrared detector, high sensitivity, anti-jamming, stable performance2. High precision analog output, combined with PID control algorithm, allows the robot tracks lines more stableSpecifications1. Power: 3.3V ~ 5V2. Dimension: 78mm × 18mm3. Detector spacing: 16mm4. Mounting holes size: 3mm5. Detection range: 1cm ~ 5cmApplicationsRobot line trackingHow to UseIn the case of working with a MCU:- VCC ? 3.3V ~ 5V- GND ? GND- IR1 ? MCU.IO (ch1, analog output)- IR2 ? MCU.IO (ch2, analog output)- IR3 ? MCU.IO (ch3, analog output)- IR4 ? MCU.IO (ch4, analog output)- IR5 ? MCU.IO (ch5, analog output)

Read more less

OverviewEmitting a beam of infrared, and receive the reflected beamFeatures wide range voltage comparator LM393Adjustable sensitivitySignal output indicatorSpecificationsPower: 3.3V ~ 5VDimension: 39mm × 15.5mm (include the IR LED)Mounting holes size: 3mmDetection range: 2cm ~ 30cm (depending on the obstacle's color, farthest for white)Detection angle: 35°Recommended environment: in door, to avoid the sunshine effectApplicationsRobot path trackingObstacle-avoiding carPipeline counterHow to UseIn the case of working with a MCU:VCC ↔ 3.3V ~ 5VGND ↔ GNDAOUT ↔ MCU.IO (analog output)DOUT ↔ MCU.IO (digital output)

Read more less

OverviewThe Compute Module IO Board Plus is a development board which you can plug a Raspberry Pi Compute Module into, and make use of the resources of Pi more flexibly. It is compatible with the Compute Module IO Board V3 from the Raspberry Pi Foundation, along with various common use components.Compute Module IO Board Plus Features1. Compatible with the Compute Module IO Board V3 from the Raspberry Pi Foundation2. Raspberry Pi GPIO header, for connecting sorts of Raspberry Pi HATs3. Arduino connectivity, also supports Arduino shields4. 1-WIRE interface, for connecting single-bus devices like DS18B205. 4x keys, 4x LEDs, 1x Buzzer, for I/O testing6. Onboard USB HUB, allows connecting more USB devices7. IR receiver, IR remote control is available8. Onboard USB TO UART, for serial debugging9. Sensor interface10. 10-bit ADC, 38KSPS, 11-ch (6-ch for Arduino interface, 5-ch for sensors)11. 16-bit DAC, 2-ch12. Onboard RTC, one of the most common and useful functionsWhat is on the Compute Module IO Board Plus1. Compute Module interface: for connecting Compute Module (CM3 / CM3L / CM3+ / CM3+L)2. Compute Module GPIO header: breakout all the Compute Module pins3. Raspberry Pi GPIO header: for connecting Raspberry Pi HATs4. CSI interface: camera ports, for connecting Raspberry Pi Camera5. DSI interface: display ports, for connecting Raspberry Pi LCD6. HDMI port7. USB ports: for connecting USB devices8. USB SLAVE interface: allows you to burn system image in to Compute Module 39. USB TO UART interface: for serial debugging10. Arduino header: for connecting Arduino shields11. AD/DA input/output screw terminals12. 1-WIRE interface: for connecting single-bus devices like DS18B2013. Sensor interface14. Power port: 5V 2.5A15. FE1.1S: USB HUB chip16. 12MHz crystal17. CP2102: USB TO UART converter18. Micro SD card slot: Insert a Micro SD card with pre-burnt system, to start up Compute Module 3 Lite19. TLC1543: AD converter20. DAC8552: 16-bit DAC, 2-ch21. DS3231: High-precision RTC chip, I2C interface22. RTC battery holder: supports CR1220 batteries23. Voltage regulator: 3.3V / 2.5V / 1.8V 24. LFN0038K: IR receiver25. Buzzer26. Power indicator27. ACT indicator: indicating the Micro SD card status28. User LEDs29. User Keys30. BOOT selection- EN: enable the PC to access SD card/eMMC through USB SLAVE- DIS: the Compute Module will boot from SD card/eMMC31. VGx power selection: config the I/O level32. USB HUB enable jumper: HUB enable and USB SLAVE power selection33. ADC/DAC configuration: config the power supply and reference voltage of ADC/DAC34. Peripheral configuration: config the control pins of UART, user keys, user LEDs, 1-WIRE interface, IR receiver, and buzzer35. Arduino AD selection- Connect 1 and 2: Arduino A0-A5 as digital control pin- Connect 2 and 3: Arduino A0-A5 as AD input

Read more less

Features:1. This kit uses ARM Cortex-M3 processor (STM32F103C8), and includes a 2.4-inch color TFT display screen, can be used as ARM test development board.2. Can be secondary development on the basis of this kit, for example, it can be changed to Millivoltmeter, data loggers.3. Adjustable vertical displacement, and with instructions.4. With automatic, regular and one-shot modes, easy to capture the moment waveform.5. Available rising or falling edge trigger.6. Observable previous trigger waveform (negative delay).7. Can freeze at any time waveform display (HOLD function).8. Come 1Hz /3.3V square wave test signal source.9. With waveform parameter digital display, including frequency, period, pulse width, duty ratio, MAX./MIN./AVG./Peak-Peak/virtual values.10. Waveform storage function: will not lose the waveform after power off.11. Short-circuit and open-circuit detection: can help the user find out the soldering error.12. TFT controller recognition function. Note:This DIY kit is soldered. Specifications:1. Maximum Real-time Sampling Rate: 1Msps2. Accuracy: 12Bit3. Sampling Buffer Depth: 1024 bytes4. Analog Bandwidth: 0-200KHz5. Vertical Sensitivity: 10mV / Div - 5V / Div (1-2-5 progressive manner)6. Input Impedance: 1Mohm7. Maximum Input Voltage: 50Vpp (1: 1 probe), 400Vpp (10: 1 probe)8. Coupling Modes: DC / AC / GND9. The Horizontal Time Base Range: 10μs / Div - 50s / Div (1-2-5 progressive manner)10. Supply Voltage: DC 9V11. PCB Size: 117 * 76mm / 4.6 * 3in12. Screen Size: 52 * 40mm / 2 * 1.57in Package List:- 1 * DSO138 soldered Oscilloscope Kit- Soldering- 1 * Probe- 3 * User Manual(English)

Read more less

1. Product: SG90 Servo2. Torque: 2.0kg/cm(4.8V), 2.2kg/cm(6V)3. Speed: 0.09s/60°(4.8V), 0.08s/60°(6V)4. Rotate angle: 180°5. Operating voltage: 4.8 ~ 6V6. Gear: plastic7. Dead band: 7us8. Weight: 10.5g9. Dimension: 22.8mm × 12.2mm × 28.5mm

Read more less

1. 800x480 hardware resolution, configurable by software (up to 1920x1080)2. Supports popular mini PCs such as Raspberry Pi, BB Black, Banana Pi, as well as general desktop computers - When works with Raspberry Pi, supports Raspbian, Ubuntu, WIN10 IOT, single touch, and driver free - When work as a computer monitor, supports Windows 10/8.1/8/7, single touch, and driver free3. Supports popular game consoles like Microsoft XBOX360, Sony PS4, and Nintendo Switch, etc.4. Multi languages OSD menu, for power management, brightness/contrast adjustment, etc.5. 3.5mm audio jack, speaker connector, supports HDMI audio output6. Also supports VGA input (specific cable is required and should be purchased separately)

Read more less

1. 7inch IPS screen,1024x600 hardware resolution, configurable by software (up to 1920 x1080)2. Toughened glass capacitive touch panel, 6H hardness3. Supports popular mini PCs such as Raspberry Pi, BB Black, Banana Pi, as well as general desktop computers4. When works with Raspberry Pi, supports Raspbian, Ubuntu, -WIN10 IOT, single touch, and driver free5. When work as a computer monitor, supports Windows 10/8.1/8/7, five-points touch, and driver free6. Multi languages OSD menu, for power management, brightness/contrast adjustment, etc.7. 3.5mm audio jack, supports HDMI audio output8. Also supports VGA input (specific cable is required and should be purchased separately)9. High quality PC case, optional tilt angle: 30?°/50?°

Read more less

1. IPS screen, 1024x600 hardware resolution, configurable by software (up to 1920x1080)2. Supports popular mini PCs such as Raspberry Pi, BB Black, Banana Pi, as well as general desktop computers3. When works with Raspberry Pi, supports Raspbian, Ubuntu, WIN10 IOT, single touch, and driver free4. When work as a computer monitor, supports Windows 10/8.1/8/7, five-points touch, and driver free5. Supports popular game consoles like Microsoft XBOX360, Sony PS4, and Nintendo Switch, etc.6. Multi languages OSD menu, for power management, brightness/contrast adjustment, etc.3. 3.5mm audio jack, speaker connector, supports HDMI audio output8. Also supports VGA input (specific cable is required and should be purchased separately)

Read more less

1. 13.3inch IPS screen,1920x1080 high resolution2. Toughened glass capacitive touch panel, 6H hardness3. Supports popular mini PCs such as Raspberry Pi, BB Black, as well as general desktop computers4. When works with Raspberry Pi, supports Raspbian, Ubuntu, WIN10 IOT, single touch, and driver free5. hen work as a computer monitor, supports Windows 10/8.1/8/7, ten-points touch, and driver free6. Multi languages OSD menu, for power management, brightness/contrast adjustment, etc.7. 3.5mm audio jack, supports HDMI audio outputEmbedded ferrite Hi-Fi speaker8. Also supports VGA input (specific cable is required and should be purchased separately)9. 75x75mm spacing mounting holes (M4 screw hole) for general wall mount

Read more less

1. 800 x 480 high resolution,Resistive touch control 2. Compatible and Direct-connect with any revision of Raspberry Pi (except the Pi 1 model B or Pi Zero, which requires an HDMI cable) 3. Drivers provided (works with your own Raspbian/Ubuntu directly) 4. HDMI interface for displaying, no I/Os required (however, the touch panel still needs I/Os) 5. Backlight can be turned off to lower power consumption 6. High quality immersion gold surface plating

Read more less

1. 800 x 480 high resolution,Resistive touch control 2. Supports Raspberry Pi 3. Supports popular mini-PCs like Raspberry Pi, BB Black, etc. 4. Not only for mini-PCs, it can work as a computer monitor just like any other general HDMI screen 5. Backlight can be turned off to lower power consumption

Read more less

1. 800 x 480 high resolution,Capacitive touch control 2. Supports popular mini-PCs like Raspberry Pi, BB Black, etc. -When working with Raspberry Pi, supports Raspbian, Ubuntu, WIN10 IoT, single touch, and driver free -When working with other mini-PCs, driver is required and should be developed by users 3. Not only for mini-PCs, it can work as a computer monitor just like any other general HDMI screen 4. When works as a computer monitor, supports Windows 10/8.1/8/7, five-points touch, and driver free 5. Backlight can be turned off to lower power consumption 6. Note: to use the LCD with following mini-PCs( additional cables are required and should be purchased separately: Raspberry Pi Zero: HDMI cable, USB-type-A-receptacle-to-Micro-B-plug-cable BB Black: HDMI cable)

Read more less

1. 7inch IPS screen, 1024 x 600 high resolution,Capacitive touch control 2.Supports popular mini-PCs like Raspberry Pi, BB Black, etc. -When working with Raspberry Pi, supports Raspbian, Ubuntu, WIN10 IoT, single touch, and driver free -When working with other mini-PCs, driver is required and should be developed by users 3. Not only for mini-PCs, it can work as a computer monitor just like any other general HDMI screen 4. When works as a computer monitor, supports Windows 10/8.1/8/7, five-points touch, and driver free 5. Backlight can be turned off to lower power consumption 6. Note: to use the LCD with following mini-PCs, additional cables are required and should be purchased separately: Raspberry Pi Zero: HDMI cable, USB-type-A-receptacle-to-Micro-B-plug-cable BB Black: HDMI cable

Read more less

1. 1024 x 600 high resolution,Capacitive touch control 2. When works with Raspberry Pi, supports Raspbian, Ubuntu, single touch, and driver free 3. When work as a computer monitor, supports Windows 10/8.1/8/7/XP, single touch, and driver free 4. Supports BB Black, comes with Angstrom image 5. Multi video input interfaces: HDMI, VGA, and AV(CVBS) 6. Multi languages OSD menu, for power management, brightness/contrast adjustment, etc. 7. Supports 100-level backlight adjustment 8. Firmware is upgradable to support more new features (continually updated) 9. Note: to use the LCD with following mini-PCs, additional cables are required and should be purchased

Read more less

7inch HDMI LCD (C) Features1. 800 x 480 high resolution,Capacitive touch control 2. Supports popular mini-PCs like Raspberry Pi, BB Black, etc. -When working with Raspberry Pi, supports Raspbian, Ubuntu, WIN10 IoT, single touch, and driver free -When working with other mini-PCs, driver is required and should be developed by users 3. Not only for mini-PCs, it can work as a computer monitor just like any other general HDMI screen 4. When works as a computer monitor, supports Windows 10/8.1/8/7, five-points touch, and driver free 5. Backlight can be turned off to lower power consumption 6. Note: to use the LCD with following mini-PCs( additional cables are required and should be purchased separately: Raspberry Pi Zero: HDMI cable, USB-type-A-receptacle-to-Micro-B-plug-cable BB Black: HDMI cable)The Case1. Material : high quality bicolor Acrylic, black and white 2. Comes with bottom holder, optional tilt angle, 45 Celsius or 60Celsius 3. Features mounting holes for Raspberry Pi B/A+/B+/2B/3B/3B+, Banana Pi, and BB Black

Read more less

1. IPS screen,1280 x 800 high resolution???Capacitive touch control, supports up to ten-points touch 2. When works with Raspberry Pi, supports Raspbian, Ubuntu, single touch, and driver free 3. When work as a computer monitor, supports Windows 10/8.1/8/7, ten-points touch, and driver free 4. Supports Banana Pi, Banana Pro, comes with Lubuntu, Raspbian images 5. Supports BB Black, comes with Angstrom image 6. HDMI interface for displaying, USB interface for touch control 7. Supports 5-level backlight adjustment 8. Note: to use the LCD with following mini-PCs, additional cables are required and should be purchased

Read more less

1. 1024 x 600 high resolution,Resistive touch control 2. Compatible and Direct-connect with any revision of Raspberry Pi (except the Pi 1 model B or Pi Zero, which requires an HDMI cable) 3. Drivers provided (works with your own Raspbian/Ubuntu directly) 4. Also works as a computer monitor, in this case, touch panel is unavailable and HDMI cable is required 5. HDMI interface for displaying, no I/Os required (however, the touch panel still needs I/Os) 6. Backlight can be turned off to lower power consumption

Read more less

1. 1024x600 high resolution 2. Compatible with Raspberry Pi 2B/3B/Zero/Zero W 3. The TFT LCD is directly driven by Raspberry Pi DPI interface, refresh rate up to 60Hz 4. Supports Raspbian, Ubuntu, OSMC, etc. 5. Backlight can be turned off to lower power consumption 6. Compact size, suit for various projects 7. Note: This item can be used for displaying ONLY

Read more less

1. 13.3inch IPS screen,1920x1080 high resolution 2. Toughened glass capacitive touch panel, 6H hardness 3. Supports popular mini PCs such as Raspberry Pi, BB Black, as well as general desktop computers 4. When works with Raspberry Pi, supports Raspbian, Ubuntu, WIN10 IOT, single touch, and driver free 5. hen work as a computer monitor, supports Windows 10/8.1/8/7, ten-points touch, and driver free 6. Multi languages OSD menu, for power management, brightness/contrast adjustment, etc. 7. 3.5mm audio jack, supports HDMI audio output Embedded ferrite Hi-Fi speaker 8. Also supports VGA input (specific cable is required and should be purchased separately) 9. 75x75mm spacing mounting holes (M4 screw hole) for general wall mount

Read more less

1. 7inch IPS screen,1024x600 hardware resolution, configurable by software (up to 1920 x1080) 2. Toughened glass capacitive touch panel, 6H hardness 3. Supports popular mini PCs such as Raspberry Pi, BB Black, Banana Pi, as well as general desktop computers 4. When works with Raspberry Pi, supports Raspbian, Ubuntu, -WIN10 IOT, single touch, and driver free 5. When work as a computer monitor, supports Windows 10/8.1/8/7, five-points touch, and driver free 6. Multi languages OSD menu, for power management, brightness/contrast adjustment, etc. 7. 3.5mm audio jack, supports HDMI audio output 8. Also supports VGA input (specific cable is required and should be purchased separately) 9. High quality PC case, optional tilt angle: 30 Celsius /50 Celsius

Read more less

1. Standard Raspberry Pi connectivity, compatible with and direct-pluggable onto Raspberry Pi 2B/3B/3B+/Zero/Zero W 2. Optional interfaces: 4-wire SPI, 3-wire SPI, I2C, configured via onboard resistor 3. 1x joystick (5-position), 3x pushbuttons, handy and useful 4. Comes with development resources and manual (examples for Raspberry Pi/Arduino/STM32) 5. Driver: SH1106 6. Interface: 4-wire SPI, 3-wire SPI, I2C 7. Display color: blue 8. Resolution: 128x64 9. Operating voltage: 3.3V

Read more less

1. Standard Raspberry Pi connectivity, compatible with and direct-pluggable onto Raspberry Pi 2B/3B/3B+/Zero/Zero W 2. 1x joystick (5-position), 3x pushbuttons, handy and useful 3. Comes with development resources and manual (examples for Raspberry Pi/Arduino/STM32) 4. Driver: ST7735S 5. Interface: SPI 6. Display color: RGB, 65K color 7. Resolution: 128x128 8. Backlight: LED 9. Operating voltage: 3.3V

Read more less