Optical Series

1. 650nm red light button: Long press the red light button to turn on the red light source and short press again to switch to the flashing/off state2. High-brightness LED lighting flashlight, convenient for construction work in dark environments3. The ceramic core can be replaced. When replacing the ceramic core, just remove the metal head4. Charge as you go, convenient and environmentally friendly. Built-in overvoltage protection circuit is fully charged and automatically cuts off the power5. Universal interface, supports a variety of wires, 2.5mm diameter universal nib, supports SC, ST, FC common interface wires6. Automatic shutdown function, automatically shut down after 10 minutes without operation7. Press the red light button + LED button at the same time for a few seconds, when the indicator light flashes 3 times, it means that the automatic shutdown function is turned on/off8. Working time: about 24 hours9. Measuring range: 10-15km10. Power supply voltage: 1.5v11. Power supply mode: USB charging/built-in lithium battery12. Battery capacity: 3.7v 600mah13. Storage temperature: -40 to 85 degrees Celsius14. Working temperature: -20 to 60 degrees Celsius15. Interface type: 2.5mm universal adapter16. Output wavelength: 650nm17. Output power: greater than 5mW / greater than 15mW / greater than 20mW / greater than 30mW18. Application: fiber splicing, testing, wire testing, network analyzer, spectrum analyzer19. Size: 125x35x17mm20. Net weight: 38gProduct list:-1 x red light pen-1 x lanyard-1 x packing box-1 x ceramic core-1 x instruction manual-1 x charging cable

Read more less

1. Carrier-grade standard, low insertion loss, high efficiency and stability, long life2. Strong optical performance, strong stability and good repeatability3. Good interchangeability, good isolation effect, easy to learn4. Can effectively suppress ground loop noise, eliminate ground interference, effectively isolate the signal site from the main control terminal electrically, and avoid accidental damage to the main control terminal5. Advanced grinding equipment ensures that the center of the optical fiber is offset. It adopts a zirconia sleeve with high temperature resistance, acid resistance and alkali resistance (high density), which has good optical properties and good mechanical properties.6. Optical fiber is widely used in distribution frames, broadband network access in optical fiber communication systems, optical fiber CATV optical fiber instruments and other reliable performance7. Good temperature stability, low insertion loss, high return loss8. Insertion loss: less than or equal to 0.3dB9. Return loss: greater than or equal to 55dB10. Insertion times: more than 1000 times11. Ferrule Type: Ceramic12. Working temperature: -40 to 80 degrees Celsius13. Storage temperature: -55 to 85 degrees Celsius14. Ambient humidity: 95RH15. Accurate attenuation: less than 0.5db16. Wavelength parameters: single mode 1310-1550nm17. Wavelength: 1310-1550nm

Read more less

1. 8-way bidirectional data network optical transceiver2. Good compatibility, quality chip, stable performance, SC3. Plug and play, stable transmission, fully compatible4. Easy to use, two-way communication, good heat dissipation, stable performance, easy to use5. Long-distance transmission, optical fiber transmission distance up to 20KM (single-mode)6. No software, no drivers, wide range of uses, plug and play7. The design of multiple cooling ports on both sides of the fuselage can effectively dissipate heat and ensure the effective operation of the device. .8. Metal frosted shell, simple and beautiful, easy to install, no on-site debugging9. Humanized control design, support plug and play, more stable and safer10. Scope of application: multimedia teaching, security monitoring, remote video conferencing, radio and television transmission, community/campus monitoring construction11. Wavelength single mode: 1310nm, 1510nm12. Shell material: cold rolled sheet13. Fiber type: single mode single fiber14. Optical fiber interface: SC interface15. Power supply voltage AC220V DC5V16. Working temperature -5 to 70 degrees Celsius17. Transmission distance: 20km18. Terminal type: RS48519. Dimensions: 136 x 100 x 27mm20. Bare metal weight: 235g/set21. Gross weight: 726g/pairShipping list-1 x Optical Transmitter-1 x Receiver-1 x Instruction manual-2 x Power supply

Read more less

1. Material: ABS, aluminum alloy, electronic components2. Features: high performance, laser chip, pulse continuous wave3. Output power: 1-60mW4. Wavelength: 650nm5. Universal interface: 2.5mm (FC/SC/ST/LC)6. Working temperature: minus 10-60 degrees Celsius7. Batteries: AAA batteries x 2 (batteries are not included in delivery)8. Standard interface 2.5mm, suitable for FC/SC/ST/LC9. The metal head/ceramic core can be replaced by yourself10. One-button operation, simple and convenient11. Made of high-quality aluminum alloy, corrosion-resistant and comfortable to the touch12. Product size: 17.5 x 2.6 cm13. Weight: 120 grams

Read more less

1. Material: ABS, aluminum alloy, electronic components2. Features: high performance, laser chip, pulse continuous wave3. Output power: 1-60mW4. Wavelength: 650nm5. Universal interface: 2.5mm (FC/SC/ST/LC)6. Working temperature: minus 10-60 degrees Celsius7. Batteries: AAA batteries x 2 (batteries are not included in delivery)8. Standard interface 2.5mm, suitable for FC/SC/ST/LC9. The metal head/ceramic core can be replaced by yourself10. One-button operation, simple and convenient11. Made of high-quality aluminum alloy, corrosion-resistant and comfortable to the touch12. Product size: 17.5 x 2.6 cm13. Weight: 120 grams

Read more less

1. Material: ABS, aluminum alloy, electronic components2. Features: high performance, laser chip, pulse continuous wave3. Output power: 1-60mW4. Wavelength: 650nm5. Universal interface: 2.5mm (FC/SC/ST/LC)6. Working temperature: minus 10-60 degrees Celsius7. Batteries: AAA batteries x 2 (batteries are not included in delivery)8. Standard interface 2.5mm, suitable for FC/SC/ST/LC9. The metal head/ceramic core can be replaced by yourself10. One-button operation, simple and convenient11. Made of high-quality aluminum alloy, corrosion-resistant and comfortable to the touch12. Product size: 17.5 x 2.6 cm13. Weight: 120 grams

Read more less

1. Material: ABS, aluminum alloy, electronic components2. Features: high performance, laser chip, pulse continuous wave3. Output power: 1-60mW4. Wavelength: 650nm5. Universal interface: 2.5mm (FC/SC/ST/LC)6. Working temperature: minus 10-60 degrees Celsius7. Batteries: AAA batteries x 2 (batteries are not included in delivery)8. Standard interface 2.5mm, suitable for FC/SC/ST/LC9. The metal head/ceramic core can be replaced by yourself10. One-button operation, simple and convenient11. Made of high-quality aluminum alloy, corrosion-resistant and comfortable to the touch12. Product size: 17.5 x 2.6 cm13. Weight: 120 grams

Read more less

1. Material: ABS, aluminum alloy, electronic components2. Features: high performance, laser chip, pulse continuous wave3. Output power: 1-60mW4. Wavelength: 650nm5. Universal interface: 2.5mm (FC/SC/ST/LC)6. Working temperature: minus 10-60 degrees Celsius7. Batteries: AAA batteries x 2 (batteries are not included in delivery)8. Standard interface 2.5mm, suitable for FC/SC/ST/LC9. The metal head/ceramic core can be replaced by yourself10. One-button operation, simple and convenient11. Made of high-quality aluminum alloy, corrosion-resistant and comfortable to the touch12. Product size: 17.5 x 2.6 cm13. Weight: 120 grams

Read more less

1. Material: ABS, aluminum alloy, electronic components2. Features: high performance, laser chip, pulse continuous wave3. Output power: 1-60mW4. Wavelength: 650nm5. Universal interface: 2.5mm (FC/SC/ST/LC)6. Working temperature: minus 10-60 degrees Celsius7. Batteries: AAA batteries x 2 (batteries are not included in delivery)8. Standard interface 2.5mm, suitable for FC/SC/ST/LC9. The metal head/ceramic core can be replaced by yourself10. One-button operation, simple and convenient11. Made of high-quality aluminum alloy, corrosion-resistant and comfortable to the touch12. Product size: 17.5 x 2.6 cm13. Weight: 120 grams

Read more less

1. Material: ABS, aluminum alloy, electronic components2. Features: high performance, laser chip, pulse continuous wave3. Output power: 1-60mW4. Wavelength: 650nm5. Universal interface: 2.5mm (FC/SC/ST/LC)6. Working temperature: minus 10-60 degrees Celsius7. Batteries: AAA batteries x 2 (batteries are not included in delivery)8. Standard interface 2.5mm, suitable for FC/SC/ST/LC9. The metal head/ceramic core can be replaced by yourself10. One-button operation, simple and convenient11. Made of high-quality aluminum alloy, corrosion-resistant and comfortable to the touch12. Product size: 17.5 x 2.6 cm13. Weight: 120 grams

Read more less

1. Material: ABS, aluminum alloy, electronic components2. Features: high performance, laser chip, pulse continuous wave3. Output power: 1-60mW4. Wavelength: 650nm5. Universal interface: 2.5mm (FC/SC/ST/LC)6. Working temperature: minus 10-60 degrees Celsius7. Batteries: AAA batteries x 2 (batteries are not included in delivery)8. Standard interface 2.5mm, suitable for FC/SC/ST/LC9. The metal head/ceramic core can be replaced by yourself10. One-button operation, simple and convenient11. Made of high-quality aluminum alloy, corrosion-resistant and comfortable to the touch12. Product size: 17.5 x 2.6 cm13. Weight: 120 grams

Read more less

1. Signal to noise: 120dB2. Degree of separation: 85dB3. Frequency response: 20Hz-20KHz + - 0.5db4. Output voltage: 2.2V5. DC 5V 1A power supply output 110v-240v broadband convert DC5V power6. Converts DTS or AC3 digital audio source to 5.1 analog audio or stereo audio output.7. The L or R stereo analog signals after the digital processing chip converts it to 5.1 channel analog output8. Multi-channel audio input SPDIF, Coaxial, stereo 2 x SPDIF input, 1 x Coaxial input, 1 x STEREO9. 5.1 channel analog or stereo output

Read more less

Features:1. With 3.5mm and 2 RCA 2 connection options, you can play music on 2 speakers at the same time2. Suitable for most speakers3. The effective connection distance is up to 10m, and the music playback can be controlled remotely4. Use the charging cable to connect to your car or other power source. When the car starts or has electricity, it will automatically turn on and automatically connect to the device you connected last time; when the car is turned off, it will automatically turn off5. Multi-point Bluetooth connection6. Easy to set upProduct specifications:1. USB cable length: 75cm2. Host weight: 34g3. USB cable weight: 18g4. Body size: 5.5x5.5x2.2cmPacking list:Host x 1USB cable x 1

Read more less

1. The fiber optic drop cable patch cord has two connectors in each end of the cable to make connection; pigtail cable is one cable with a connector. The connectors are with SC type, ferrule to be polished as UPC. 2. Optical fiber patch cable is made up by optical communication unit, strengthen pieces and the sheath composition, that is put the optical communication unit in the middle, both sides parallel place two root non-metallic strengthen members or metal strengthening component phosphate steel wire, finally squeeze the black sheath into cable. 3. Special bending resistance of optical fiber, offer more bandwidth and enhance network transmission characteristic, easily realize the broadband, CATV and phone combination of three nets. 4. Cable simple structure, the function is strong. 5. The groove design, easy separating, convenient in, easy installation and maintenance. 6. It is suitable for residential homes, street homes and rural fiber FTTH homes. 7. Interface type: SC 8. Number of cores: single core 9. Mating times: more than 1000 times 10. Insertion loss: greater than 50 11. Return loss: less than 0.30 12. Repeatability: less than 0.10 13. Interchangeability: less than 0.20 14. Transmission distance: 1KM-3KM 15. Bending angle: more than 100 degrees 16. Product material: PVC + phosphating steel wire 17. Cable length: 300m

Read more less

1. Standard: IEEE 802.3z/AB 1000Base-T / SC / LX / ZX 2. Interface: UTP RJ45 and Fiber: SC 3. Transfer rate: the UTP rate: 10/100 / 1000Mbps 1000Mbps; fiber: 4. Duplex mode: electrical port full-duplex or half duplex, optical port full-duplex 5. UTP: 5E, Category 6 6. Current: AC 220V (175 - 260V), 50Hz 7. The transceiver optical port only 1000M full duplex electrical port can work in 10M, 100M or 1000M, 10/100/1000M adaptive optical transceiver

Read more less

1. Standard: IEEE 802.3u Fast Ethernet 10 /100 Base-TX and 100 Base-FX 2. Interface: UTP RJ45 and Fiber: SC 3. Transfer rate: the UTP rate: 10/100 / 1000Mbps 1000Mbps; fiber: 4. Duplex mode: electrical port full-duplex or half duplex, optical port full-duplex 5. Data transfer mode: 10 / 100Mbps 6. Power requirement: AC 100 -260V DC 1A@ + 5V 7. Cable: UTP: Cat.5UTP cable

Read more less

1. Standard: IEEE 802.3z/AB 1000Base-T / SC / LX / ZX 2. Interface: UTP RJ45 and Fiber: SC 3. Transfer rate: the UTP rate: 10/100 / 1000Mbps 1000Mbps; fiber: 4. Duplex mode: electrical port full-duplex or half duplex, optical port full-duplex 5. UTP: 5E, Category 6 6. Current: AC 220V (175 - 260V), 50Hz 7. The transceiver optical port only 1000M full duplex electrical port can work in 10M, 1 00M or 1000M, 10/100/1000M adaptive optical transceiver

Read more less

specification: 1. Fiber Type: single-mode 2. Condition: New in Box-Includes Power Cord and Manual 3. Operating standards: IEEE802.3u, 10 / 100Base-TX and 100Base-FX 4. MAC address table: 1K Connector: 1. UTP: RJ-45 10 / 100Mbps; 2. Fiber: SC 100Mbps Cable: 1. UTP: Cat. 5 UTP (the max distance up to 100m) 2. Fiber (single mode): 50/125, 62.5 / 125 m (the max distance up to 2km or 5km) Flow Control 1. Full Duplex: Supporting standard IEEE802.3x 2. Half Duplex: Backpressure 3. LED: Power, FX FDX, FX Link / Act, TX 100, TX FDX, TX Link / Act. 4. Power: AC 110V-240V to DC 5V; DC 48V to DC 5V. 5. Ambient Temperature: 0-70 degree 6. Humidity: 5%-90% Dimensions: 1. Internal power: 30 ?? 110 ?? 140mm 2. External power: 26 ?? 70 ?? 93mm

Read more less

1. AlphaAmbient temperature: -25 - +40 Degrees Celsius 2. Relative Humidity: Less than or equal to 85% (+30 Degrees Celsius) 3. Atmospheric pressure: 70kPa - 106kPa 4. Insulation resistance: cable terminal and metal components and fiber optic cable metal to strengthen the core, the fiber optic cable between the metal components, fiber metal structures and between the insulation resistance should be greater than 2 x 104Milliohm 5. Dielectric strength: between cable terminals and metal components and fiber metal reinforced core fiber optic cable between the metal components, fiber optic cable between the metal components and ground 15kV DC voltage, 1min without breakdown, arcing phenomena Product Features: 1. can be used for the two-cable with fiber optic cable to strengthen the core holder, and fixed fiber optic cable jacket, Block has a protective earthing. 2. the set of fiber optic cable, connecting pigtail, pigtails, jumpers, asylum and other functions as one. 3. line redundancy long with a capacity plate asylum protection. 4. disk fiber plate for layering, you can easily increase or decrease in construction, operation convenience. 5. disk fiber plate were given to mark, easy to identify. 6. fiber pigtail, patch cord, import and export rubber protective sleeve to control the radius of curvature in the 3.75CM above. 7. the terminal box by screws, can be easily fixed on the wall or the user that the right place 8. Widely used in city, agricultural, then the network system, data, image transmission systems, CATV cable television series, for indoor fiber optic cable through access and branch continuation, played the role of the the pigtail disk storage and protection of joints, the use of cold-rolled steelelectrostatic spray made a??a??reasonable structure, beautiful big before the fiber optic cable to strengthen the core in the terminal

Read more less

Introduction: This SPDIF/TOSLINK Digital Optical Audio splitter allows you to distribute input digital optical audio to three amplifiers or receivers, seamlessly and flawlessly without degradation. It supports LPCM2.0, DTS and Dolby-AC3 audio formats. Features: 1. One ways of optical fiber signal input splitter to three sets of SPDIF/TosLink signal receiving device 2. Maintain digital sonic integrity and provides crystal clear digital sound quality over the long range 3. Support signal retiming 4. One way optical fiber signal splits into three identical outputs at the same time 5. Support Dolby Digital & DTS 5.1 6. Support LPCM Stereo 32 kHz 44.1 kHz 48 kHz and 96 kHz 7. Integrated circuit implementation delivers unsurpassed reliability and fidelity. Virtually no loss of quality 8. Use optical fiber cable loss less the 0.2Db/m, Output distance can be up to 40m. 9. Over-voltage protection 10. Plug and play, Installs in minutes 11. DC 5V/500mA power supply Specification: 1. Audio format support: LPCM2.0/DTS/Dolby-AC3 2. Peak wave length: 650nm 3. Max baud rate: 16Mbps 4. Output cable distance: >= 40m (Use the optical fiber cable loss less the 0.2Db/m) 5. Max working current: 100mA 6. Input: AC (50HZ, 60HZ) 100V-240V 7. Output: DC5V/500mA 8. Operating Temperature range :( 0 to +40 Celsius) 9. Operating Humidity range: 5 to 90 percent RH (No Condensation) 10. Weight: 35g 11. Dimension: 54mm x 54mm x 23.5mm

Read more less

1. Product name: SC-SC Fiber Optic Jumper 2. Connector type: SC-SC 3. Core diameter: 62.5 / 125um 4. Sheath diameter: 3.0mm 5. Length: 3m 6. Material: PVC 7. Color: Orange feature 1. Low insertion loss 2. Good repeatability 3. Not easy to damage 4. Mutual insertion performance 5. Good temperature stability 6. Application of optical fiber jumper: communication system, data transmission, cable TV, local area network (LAN), optical fiber sensor, test equipment, etc.

Read more less

1. Product name: FC-FC Dual-Core Multi Mode Fiber Optic Jumper 2. Connector type: FC-FC 3. Core diameter: 62.5 / 125um 4. Sheath diameter: 3.0mm 5. Length: 3m 6. Material: PVC 7. Color: Orange feature 1. Low insertion loss 2. Good repeatability 3. Not easy to damage 4. Mutual insertion performance 5. Good temperature stability 6. Application of optical fiber jumper: communication system, data transmission, cable TV, local area network (LAN), optical fiber sensor, test equipment, etc.

Read more less

1. Product name: LC-LC Dual-Core Multi Mode Fiber Optic Jumper 2. Connector type: LC-LC 3. Core diameter: 62.5 / 125um 4. Sheath diameter: 2.0mm 5. Length: 3m 6. Material: PVC 7. Color: Orange feature 1. Low insertion loss 2. Good repeatability 3. Not easy to damage 4. Mutual insertion performance 5. Good temperature stability 6. Application of optical fiber jumper: communication system, data transmission, cable TV, local area network (LAN), optical fiber sensor, test equipment, etc.

Read more less

1. Product name: ST-ST Dual-Core Multi Mode Fiber Optic Jumper 2. Connector type: ST-ST 3. Core diameter: 62.5 / 125um 4. Sheath diameter: 3.0mm 5. Length: 3m 6. Material: PVC 7. Color: Orange feature 1. Low insertion loss 2. Good repeatability 3. Not easy to damage 4. Mutual insertion performance 5. Good temperature stability 6. Application of optical fiber jumper: communication system, data transmission, cable TV, local area network (LAN), optical fiber sensor, test equipment, etc.

Read more less

1. Scope of application: optical fiber communication network , fiber-optic broadband access networks, optical fiber of CATV , fiber optic instrumentation, optical fiber LAN 2. Composition of raw materials: precision ceramic casing 3. Flame resistance, reaching a 94 - V0 high-temperature environmental protection, comply with ROHS environmental requirements 4. Impact strength , look beautiful 5. Rugged and easy to use

Read more less

1. Scope of application: optical fiber communication network , fiber-optic broadband access networks, optical fiber of CATV , fiber optic instrumentation, optical fiber LAN 2. Composition of raw materials: precision ceramic casing 3. Flame resistance, reaching a 94 - V0 high-temperature environmental protection, comply with ROHS environmental requirements 4. Impact strength , look beautiful 5. Rugged and easy to use

Read more less

1. Product name: SC-ST Fiber Optic Jumper 2. Connector type: SC-ST 3. Core diameter: 62.5 / 125um 4. Sheath diameter: 3.0mm 5. Length: 3m 6. Material: PVC 7. Color: Orange feature 1. Low insertion loss 2. Good repeatability 3. Not easy to damage 4. Mutual insertion performance 5. Good temperature stability 6. Application of optical fiber jumper: communication system, data transmission, cable TV, local area network (LAN), optical fiber sensor, test equipment, etc.

Read more less

1. Product name: SC-FC Fiber Optic Jumper 2. Connector type: SC-FC 3. Core diameter: 62.5 / 125um 4. Sheath diameter: 3.0mm 5. Length: 3m 6. Material: PVC 7. Color: Orange feature 1. Low insertion loss 2. Good repeatability 3. Not easy to damage 4. Mutual insertion performance 5. Good temperature stability 6. Application of optical fiber jumper: communication system, data transmission, cable TV, local area network (LAN), optical fiber sensor, test equipment, etc.

Read more less

1. Product name: SC-FC Fiber Optic Jumper 2. Connector type: SC-FC 3. Core diameter: 9 / 125um 4. Sheath diameter: 3.0mm 5. Length: 3m 6. Material: PVC 7. Color: Orange feature 1. Low insertion loss 2. Good repeatability 3. Not easy to damage 4. Mutual insertion performance 5. Good temperature stability 6. Application of optical fiber jumper: communication system, data transmission, cable TV, local area network (LAN), optical fiber sensor, test equipment, etc.

Read more less

1. Product name: LC-ST Single-Core Single Mode Fiber Optic Jumper 2. Connector type: LC-ST 3. Core diameter: 9 / 125um 4. Sheath diameter: 2.0mm 5. Length: 3m 6. Material: PVC 7. Color: Yellow feature 1. Low insertion loss 2. Good repeatability 3. Not easy to damage 4. Mutual insertion performance 5. Good temperature stability 6. Application of optical fiber jumper: communication system, data transmission, cable TV, local area network (LAN), optical fiber sensor, test equipment, etc.

Read more less

1. Product name: FC-ST Fiber Optic Jumper 2. Connector type: FC-ST 3. Core diameter: 62.5 / 125um 4. Sheath diameter: 3.0mm 5. Length: 3m 6. Material: PVC 7. Color: Orange feature 1. Low insertion loss 2. Good repeatability 3. Not easy to damage 4. Mutual insertion performance 5. Good temperature stability 6. Application of optical fiber jumper: communication system, data transmission, cable TV, local area network (LAN), optical fiber sensor, test equipment, etc.

Read more less

1. Product name: LC-FC Fiber Optic Jumper 2. Connector type: LC-FC 3. Core diameter: 62.5 / 125um 4. Sheath diameter: 3.0mm 5. Length: 3m 6. Material: PVC 7. Color: Orange feature 1. Low insertion loss 2. Good repeatability 3. Not easy to damage 4. Mutual insertion performance 5. Good temperature stability 6. Application of optical fiber jumper: communication system, data transmission, cable TV, local area network (LAN), optical fiber sensor, test equipment, etc.

Read more less

1. Product name: LC-SC Fiber Optic Jumper 2. Connector type: LC-SC 3. Core diameter: 62.5 / 125um 4. Sheath diameter: 3.0mm 5. Length: 3m 6. Material: PVC 7. Color: Orange feature 1. Low insertion loss 2. Good repeatability 3. Not easy to damage 4. Mutual insertion performance 5. Good temperature stability 6. Application of optical fiber jumper: communication system, data transmission, cable TV, local area network (LAN), optical fiber sensor, test equipment, etc.

Read more less

1. Product name: SC-ST Fiber Optic Jumper 2. Connector type: SC-ST 3. Core diameter: 62.5 / 125um 4. Sheath diameter: 3.0mm 5. Length: 3m 6. Material: PVC 7. Color: Orange feature 1. Low insertion loss 2. Good repeatability 3. Not easy to damage 4. Mutual insertion performance 5. Good temperature stability 6. Application of optical fiber jumper: communication system, data transmission, cable TV, local area network (LAN), optical fiber sensor, test equipment, etc.

Read more less

1. Product name: FC-ST Fiber Optic Jumper 2. Connector type: FC-ST 3. Core diameter: 62.5 / 125um 4. Sheath diameter: 3.0mm 5. Length: 3m 6. Material: PVC 7. Color: Orange feature 1. Low insertion loss 2. Good repeatability 3. Not easy to damage 4. Mutual insertion performance 5. Good temperature stability 6. Application of optical fiber jumper: communication system, data transmission, cable TV, local area network (LAN), optical fiber sensor, test equipment, etc.

Read more less

1. Product name: FC-ST Single-Core Single Mode Fiber Optic Jumper 2. Connector type: FC-ST 3. Core diameter: 9 / 125um 4. Sheath diameter: 2.0mm 5. Length: 3m 6. Material: PVC 7. Color: Yellow feature 1. Low insertion loss 2. Good repeatability 3. Not easy to damage 4. Mutual insertion performance 5. Good temperature stability 6. Application of optical fiber jumper: communication system, data transmission, cable TV, local area network (LAN), optical fiber sensor, test equipment, etc.

Read more less

1. Product name: SC-SC Fiber Optic Jumper 2. Connector type: SC-SC 3. Core diameter: 62.5 / 125um 4. Sheath diameter: 3.0mm 5. Length: 3m 6. Material: PVC 7. Color: Orange feature 1. Low insertion loss 2. Good repeatability 3. Not easy to damage 4. Mutual insertion performance 5. Good temperature stability 6. Application of optical fiber jumper: communication system, data transmission, cable TV, local area network (LAN), optical fiber sensor, test equipment, etc.

Read more less

1. Product name: SC-DC Single-Core Single Mode Fiber Optic Jumper 2. Connector type: SC-SC 3. Core diameter: 9 / 125um 4. Sheath diameter: 2.0mm 5. Length: 3m 6. Material: PVC 7. Color: Yellow feature 1. Low insertion loss 2. Good repeatability 3. Not easy to damage 4. Mutual insertion performance 5. Good temperature stability 6. Application of optical fiber jumper: communication system, data transmission, cable TV, local area network (LAN), optical fiber sensor, test equipment, etc.

Read more less

1. Product name: LC-LC Fiber Optic Jumper 2. Connector type: LC-LC 3. Core diameter: 9 / 125um 4. Sheath diameter: 3.0mm 5. Length: 3m 6. Material: PVC 7. Color: Yellow feature 1. Low insertion loss 2. Good repeatability 3. Not easy to damage 4. Mutual insertion performance 5. Good temperature stability 6. Application of optical fiber jumper: communication system, data transmission, cable TV, local area network (LAN), optical fiber sensor, test equipment, etc.

Read more less

1. Product name: ST-ST Fiber Optic Jumper 2. Connector type: ST-ST 3. Core diameter: 62.5 / 125um 4. Sheath diameter: 3.0mm 5. Length: 3m 6. Material: PVC 7. Color: Orange feature 1. Low insertion loss 2. Good repeatability 3. Not easy to damage 4. Mutual insertion performance 5. Good temperature stability 6. Application of optical fiber jumper: communication system, data transmission, cable TV, local area network (LAN), optical fiber sensor, test equipment, etc.

Read more less

1. Product name: LC-LC single-core single-mode fiber jumper 2. Connector type: LC-LC 3. Core diameter: 9 / 125um 4. Sheath diameter: 2.0mm 5. Length: 10m 6. Material: PVC 7. Color: Yellow feature 1. Low insertion loss 2. Good repeatability 3. Not easy to damage 4. Mutual insertion performance 5. Good temperature stability 6. Application of optical fiber jumper: communication system, data transmission, cable TV, local area network (LAN), optical fiber sensor, test equipment, etc.

Read more less

1. The item is a toslink 3 to 1 optical audio switcher. 2. 3 input 1 output, allowing 3 devices to switch. It supports digital audio devices that have regular toslink connectors and provides bidirectional transmission between 1 signal and 1 audio player. 3. Rotatable switch allows user to switch transmission among 3 devices, easy operation. 4. Suitable for connecting MD DVD VCR CD Player, XBOX360, PS3 video game consoles, etc. 5. Simple installation, plug and play, easy to use.

Read more less

1.Build-in high performance RTOS operating system and audio decoder chip, support DTS/AC-3 2.Super fast start time about 3 seconds 3.Input: SPDIF Optical, Coaxial 4.Output: L-OUT-R, 3.5mm headphone port 5.Auto switch between optical and coaxial channel input 6.Auto decode AC-3/DTS(LPCM/PCM/RAW) input signal without any action 7.High compatibility: support network player, HDTV, Blu-ray DVD, DVD, PS3, XBOX 360, DM500S, DM800HD, etc. 8.Small size and metal case, anti-interference 9.Adopt RCA/3.5mm headphone port output, convenient and efficient in use 10.Supports volume adjustment

Read more less

1. Supported audio format: LPCM2.0/DTS/DOLBY-AC3 2. Three SPDIF/TosLink input interfaces, one SPDIF/TosLink output interface 3. Manual remote control button 4. Infrared interface 5. Applicable equipment: TV, audio, power amplifier, PS3, PS4, etc. 6. Product size: 6.1x6.1x6.1cm

Read more less

1. This digital-to-analog audio converter can be used for home or professional audio switching. It can convert coaxial cable or Toslink digital audio signals into analog audio. At the same time, it can be connected to peripherals like amplifiers through standard RCA-style jacks2. Convert coaxial or optical digital audio signal to analog 3.5 or L/R audio3. Support sampling rate 44.1 32., 48-96KHz playback4. The input code stream is 24bit S/PDIF left and right channels, providing electronic noise reduction transmission5. Easy to install and simple to operate6. Input: coaxial or optical digital audio7. Output: R/L (audio output connector)8. Audio input connection: Toslink, 1xRCA (coaxial)9. Audio output connection: 2xRCA (right/left), 3.5 stereo10. Power input: AC 100-240V 50/60Hz

Read more less

1. Gold-plated tip, corrosion-resistant2. Connect the male head (rotate 360 degrees at a right angle) to the female head adapter3. Right-angle adapter helps connect cables in narrow and crowded spaces4. Convert toslink jack to female adapter5. Bend at a right angle (90 degrees)6. Rotate a full circle (360 degrees) around the toslink male axis7. Easy to use

Read more less

1. The product is toslink fiber optic male to female adapter2. Even at extremely high volume, Toslink digital audio cable can provide you with the cleanest signal.3. The optical cable transmits signals through light, thus completely eliminating any possibility of RFI, EMI or ground loop interference.4. The use of high-quality optical fiber core can ensure high speed, high efficiency, high fidelity and low broadband transmission loss.5. The metal head is strong and firm.6. The dust cap prevents the connector from being contaminated when not in use.7. The fiber optic cable can be connected to DVD, CD, MINI Disc Player, TV box, projector, etc., providing you with full and delicate sound quality.

Read more less

1. Reliable quality, can achieve electrical isolation, prevent digital noise from being transmitted through the ground wire, and help to improve the signal-to-noise ratio of the DAC 2. Effectively reduce the interference of audio signals around the equipment 3. PVC shell, flame retardant, high temperature resistance, strong pressure resistance 4. Elbow design, easy to pull out 5. When the optical fiber cable cannot be bent, the 360-degree rotating adapter can be effectively replaced to ensure the normal transmission of optical fiber cable and signal 6. If the fiber interface of your device is a square port, and you have a square port fiber cable in your hand, use this adapter to easily connect 7. Can be used for: DVD, power amplifier, TV, speaker equipment, etc.

Read more less