Arduino & SCM Supplies

1. Display panel: AMOLED2. Display resolution: 466 x 4663. Display brightness: 500cd/square meter4. Communication interface: QSPI5. Touch: support6. Display size: 1.32 inch7. Display color: 16.7M8. Contrast ratio: 10000:19. Driver IC: CO5300 10. Touch IC: CST82011. Size: about 3.64 x 1cmFeatures:1. Equipped with ESP32-C6 high-performance 32-bit RISC-V processor up to 160MHz2. Integrated Wi-Fi 6, Bluetooth 5 and IEEE 802.15.4 (Zigbee 3.0 and Thread) wireless communication with excellent RF performance3. Built-in 512KB HP SRAM, 16KB LP SRAM and 320KB ROM with 16MB Flash overlay 4. 1.32 inch capacitive touch HD AMOLED screen on board, 466 x 466 resolution, 16.7 M color, can display color pictures clearly 5. Built-in CO5300 driver chip and CST820 capacitive touch chip, respectively, using QSPI and I2C interface communication, does not take up too much interface pin resources 6. On-board PWR, BOOT two customizable functions of the side button, easy to use the button for custom function development 7 Onboard 3.7V MX1.25 lithium battery charging and discharging interface 8. Equipped with ES8311 low-power audio codec chip, supports high-quality audio input and output, to meet the voice interaction and audio playback and other application requirements 9. SH1.0 12PIN expansion interface, can be used for DIY expansion of functions 10. AMOLED screen with higher contrast ratio, wider viewing angle, richer colors, faster response and better visual effects, slim design, low power consumption, flexibleSpecification: Package Weight One Package Weight 0.10kgs / 0.23lb One Package Size 8cm * 8cm * 3cm / 3.15inch * 3.15inch * 1.18inch Qty per Carton 280 Carton Weight 29.00kgs / 63.93lb Carton Size 50cm * 38cm * 34cm / 19.69inch * 14.96inch * 13.39inch Loading Container 20GP: 412 cartons * 280 pcs = 115360 pcs 40HQ: 958 cartons * 280 pcs = 268240 pcs

Read more less

1. CM5 cradle: for all versions of Compute Module 5 2. Networking: 1000M Ethernet RJ45 interface, 2500M Ethernet RJ45 interface3. Connector: Raspberry Pi 40PIN GPIO interface 4. USB: USB 3.2 Gen1 x 2 5. MIPI: 4-lane MIPI interface x 2 (22PIN 0.5mm FFC connector) 6. Video: HDMI connector x 2, supports dual 4K outputs 7. M.2: M.2 M KEY (PCle Gen2/3 x 1) 8. M.2 (4G /5G): M.2 B KEY, support access to 4G/5G communication module 9. Storage: onboard Micro SD card slot (for CM5 version without eMMC) 10. Fan nterface: 5V, 4PIN JST-SH PWM fan connector11. Power input: 7V - 36V wide voltage (round hole terminal), 5V 5A (Type-C) 12. Size:- Base plate: about 9.96 x 8.7cm)- Housing: about 10.48 x 9 x 2.97cmFeatures:1. 40PIN GPIO interface and standard CM5 connector on board, support access to Compute Module 5 Lite / eMMC series core boards2. Support M.2 NVMe hard disk, greatly improve the read and write speed of the system or file, support NVMe SSD boot3. Equipped with ETH / MIPI / HDMI / Micro SD / USB / M.2 B KEY / M KEY and other interfaces, more convenient to use4. Careful hole design ensures that each port fits the motherboard with clear silkscreen markings on the ports for easy viewing5. Shell reserved vents on the top of the better heat dissipation effect6. Wall-mounted holes on both sides of the design, more convenient to install and fix, in the back of the reserved rail mounting screw holes, you can fix the rail (not included)Packing list:- Expansion board x 1- Metal case x 1- Fan x 1- Power cord x 1- Plug x 4- Screws x 10Specification: Package Weight One Package Weight 0.50kgs / 1.11lb One Package Size 16cm * 12cm * 6cm / 6.3inch * 4.72inch * 2.36inch Qty per Carton 45 Carton Weight 23.50kgs / 51.81lb Carton Size 50cm * 38cm * 32cm / 19.69inch * 14.96inch * 12.6inch Loading Container 20GP: 438 cartons * 45 pcs = 19710 pcs 40HQ: 1018 cartons * 45 pcs = 45810 pcs

Read more less

1. Features a high-performance Xtensa 32-bit LX7 dual-core processor with a clock speed up to 240MHz2. Supports 2.4GHz Wi-Fi (802.11 b/g/n) and Bluetooth 5 (LE) with onboard antennas3. Integrated 512KB SRAM and 384KB ROM, with stacked 16MB Flash and 8MB PSRAM4. Onboard 4-inch LCD display, 480 x 480 resolution, 65K colors5. Supports I2C interface for capacitive touch control, 5-point touch6. Supports precise control via flexible clock settings and independent module power configuration, enabling multi-scenario low-power modes7. IPS display panel with outstanding performance and 160° viewing angle8. On-board ES8311 audio codec and ES7210 echo cancellation circuit for everyday audio applications9. Supports mainstream AI platforms, compatible with online large-model platforms like Doubao and DeepSeek10. Suitable for smart switches, HMI interfaces, smart home terminals, and similar applications11. Size: about 8.65 x 8.65 x 1.4 cmSpecification: Package Weight One Package Weight 0.11kgs / 0.25lb One Package Size 10cm * 10cm * 4cm / 3.94inch * 3.94inch * 1.57inch Qty per Carton 108 Carton Weight 13.00kgs / 28.66lb Carton Size 50cm * 32cm * 32cm / 19.69inch * 12.6inch * 12.6inch Loading Container 20GP: 520 cartons * 108 pcs = 56160 pcs 40HQ: 1209 cartons * 108 pcs = 130572 pcs

Read more less

1. Operating voltage:- Bare screen version: 3.3V - Module version: 3.3V/5V 2. Communication interface: 3-wire SPI, 4-wire SPI 3. Dot pitch: 0.1833 x 0.1833mm4. Resolution: 648 x 480 pixels5. Display color: red, yellow, black, white 6. Gray scale level: 2 7. Fast refresh: 12s 8. Global refresh: 20s 9. Refresh power consumption: less than 100mW 10. Sleep current: less than 0.01uA (close to 0) 11. Viewing angle: more than 170 degrees12. Display size: about 118.78 x 88.22 mm13. External size:- Bare screen: about 125.4 x 99.5 x 1.2mm- Module: about 30.5 x 65mmFeatures:1. Based on Raspberry Pi 40PIN interface design, suitable for Raspberry Pi series motherboards, Jetson Nano2. Reserved SPI control interface, can be connected to Raspberry Pi / Jetson Nano / ESP32 / Arduino / STM32 and other motherboards3. On-board level shifter chip, compatible with 3.3V and 5V level interface4. Suitable for shopping mall price tags, asset and equipment tags, electronic shelf tags and conference name tags, etc.Specification: Package Weight One Package Weight 0.15kgs / 0.34lb One Package Size 15cm * 12cm * 3cm / 5.91inch * 4.72inch * 1.18inch Qty per Carton 100 Carton Weight 16.00kgs / 35.27lb Carton Size 50cm * 38cm * 35cm / 19.69inch * 14.96inch * 13.78inch Loading Container 20GP: 401 cartons * 100 pcs = 40100 pcs 40HQ: 930 cartons * 100 pcs = 93000 pcs

Read more less

1. Operating voltage:- Bare screen version: 3.3V - Module version: 3.3V/5V 2. Communication interface: 3-wire SPI, 4-wire SPI 3. Dot pitch: 0.1833 x 0.1833mm4. Resolution: 648 x 480 pixels5. Display color: red, yellow, black, white 6. Gray scale level: 2 7. Fast refresh: 12s 8. Global refresh: 20s 9. Refresh power consumption: less than 100mW 10. Sleep current: less than 0.01uA (close to 0) 11. Viewing angle: more than 170 degrees12. Display size: about 118.78 x 88.22 mm13. External size:- Bare screen: about 125.4 x 99.5 x 1.2mm- Module: about 30.5 x 65mmFeatures:1. Based on Raspberry Pi 40PIN interface design, suitable for Raspberry Pi series motherboards, Jetson Nano2. Reserved SPI control interface, can be connected to Raspberry Pi / Jetson Nano / ESP32 / Arduino / STM32 and other motherboards3. On-board level shifter chip, compatible with 3.3V and 5V level interface4. Suitable for shopping mall price tags, asset and equipment tags, electronic shelf tags and conference name tags, etc.Specification: Package Weight One Package Weight 0.20kgs / 0.45lb One Package Size 15cm * 12cm * 3cm / 5.91inch * 4.72inch * 1.18inch Qty per Carton 100 Carton Weight 21.00kgs / 46.30lb Carton Size 50cm * 38cm * 35cm / 19.69inch * 14.96inch * 13.78inch Loading Container 20GP: 401 cartons * 100 pcs = 40100 pcs 40HQ: 930 cartons * 100 pcs = 93000 pcs

Read more less

1. Screen size: 9 inches2. Resolution: 720 x 12803. Display interface: DSI4. Display panel: IPS5. Viewing angle: 160 degrees6. Touch type: capacitive touch7. Number of touch points: 10-point touch8. Touch panel: tempered glass panel 9. Touch interface: I2C 10. Brightness: 500 cd/m211. for Raspberry Pi Pi 3A + / 3B + / 4B / 5, CM3 / 3 + / 4 / 5, support Raspberry Pi OS12. Size: about 22.3 x 14 x 1.3cmFeatures:1. IPS display panel, excellent display performance, viewing angle up to 160 degrees2. High color gamut quantum lamp technology, higher color gamut, more pure color3. 10-point touch support, the actual number of touch points is related to the software system.4. Tempered glass panel, hardness of 6H5. Brightness of backlight can be adjusted by software.6. Default is vertical display, the resolution is 720 x 1280 (H x V), you can modify the software settings, horizontal displaySpecification: Package Weight One Package Weight 0.40kgs / 0.89lb One Package Size 24cm * 16cm * 4cm / 9.45inch * 6.3inch * 1.57inch Qty per Carton 36 Carton Weight 15.40kgs / 33.95lb Carton Size 50cm * 38cm * 34cm / 19.69inch * 14.96inch * 13.39inch Loading Container 20GP: 412 cartons * 36 pcs = 14832 pcs 40HQ: 958 cartons * 36 pcs = 34488 pcs

Read more less

1. CM5 card slot: compatible with all versions of Compute Module 52. Networking: gigabit ethernet RJ45 port3. Connectors: 16-pin PCIe (PCIe Gen2/3 x 1) Raspberry Pi 40-pin GPIO interface4. USB: USB 3.2 Gen1 x 2; USB 2.0 x 25. MIPI: 4-lane MIPI interface × 2 (22-pin 0.5mm FFC connector)6. Video: HDMI interface x 2, supporting dual 4K output7. Audio: compatible with standard 3.5mm headphone jacks for audio input/output via accessory module8. Storage: onboard Micro SD card slot (For CM5 versions without eMMC)9. Fan Interface: 5V, 4-pin JST-SH PWM fan connector10. Power Input: DC 5V 5A11. Onboard 40-pin GPIO interface and standard CM5 connector, supporting Compute Module 5 Lite / eMMC series core boards12. Onboard USB audio decoder chip, supports microphone connection13. Size: about 8.5 x 5.6 cmPackage contents:- CM5-to-Pi5-Adapter x 1- Audio-Adapter x 1- MX1.25 4-pin dual-ended cable (approx. 200mm) x 1- Screw set x 1Specification: Package Weight One Package Weight 0.06kgs / 0.14lb One Package Size 10cm * 7cm * 3cm / 3.94inch * 2.76inch * 1.18inch Qty per Carton 160 Carton Weight 11.00kgs / 24.25lb Carton Size 50cm * 37cm * 35cm / 19.69inch * 14.57inch * 13.78inch Loading Container 20GP: 411 cartons * 160 pcs = 65760 pcs 40HQ: 956 cartons * 160 pcs = 152960 pcs

Read more less

1. CM5 cradle: for all versions of Compute Module 5 2. Networking: 1000M Ethernet RJ45 interface, 2500M Ethernet RJ45 interface3. Connector: Raspberry Pi 40PIN GPIO interface 4. USB: USB 3.2 Gen1 x 2 5. MIPI: 4-lane MIPI interface x 2 (22PIN 0.5mm FFC connector) 6. Video: HDMI connector x 2, supports dual 4K outputs 7. M.2: M.2 M KEY (PCle Gen2/3 x 1) 8. M.2 (4G /5G): M.2 B KEY, support access to 4G/5G communication module 9. Storage: onboard Micro SD card slot (for CM5 version without eMMC) 10. Fan nterface: 5V, 4PIN JST-SH PWM fan connector11. Power input: 7V - 36V wide voltage (round hole terminal), 5V 5A (Type-C) 12. Size:- Base plate: about 9.96 x 8.7cm)- Housing: about 10.48 x 9 x 2.97cmFeatures:1. 40PIN GPIO interface and standard CM5 connector on board, support access to Compute Module 5 Lite / eMMC series core boards2. Support M.2 NVMe hard disk, greatly improve the read and write speed of the system or file, support NVMe SSD boot3. Equipped with ETH / MIPI / HDMI / Micro SD / USB / M.2 B KEY / M KEY and other interfaces, more convenient to use4. Careful hole design ensures that each port fits the motherboard with clear silkscreen markings on the ports for easy viewing5. Shell reserved vents on the top of the better heat dissipation effect6. Wall-mounted holes on both sides of the design, more convenient to install and fix, in the back of the reserved rail mounting screw holes, you can fix the rail (not included)Packing list:- Expansion board x 1- Metal case x 1- Fan x 1- Power cord x 1- Plug x 4- Screws x 10Specification: Package Weight One Package Weight 0.50kgs / 1.11lb One Package Size 16cm * 12cm * 6cm / 6.3inch * 4.72inch * 2.36inch Qty per Carton 45 Carton Weight 23.50kgs / 51.81lb Carton Size 50cm * 38cm * 32cm / 19.69inch * 14.96inch * 12.6inch Loading Container 20GP: 438 cartons * 45 pcs = 19710 pcs 40HQ: 1018 cartons * 45 pcs = 45810 pcs

Read more less

1. Type-C port supports audio and video transmission with plug-and-play functionality, instantly enlarging your phone screen2. Split-screen collaboration on your computer boosts productivity with dual-display operation3. IPS panel ensures superior display performance and color reproduction. 108% sRGB coverage expands red, green, and blue color gamut areas, delivering professional-grade design color accuracy4. HDR true-color quality pursues natural color transitions. Matte screen design minimizes ambient light interference5. 120Hz ultra-high refresh rate screen elevates gaming and movie-watching experiences6. Supports up to 10-point touch (actual touch points depend on software system). Tempered glass panel with 6H hardness. Full-lamination screen for high clarity and dust resistance7. Dual-channel speakers with black magnetic Hi-Fi drivers deliver greater volume, wider sound range, and superior audio performance8. 180° foldable metal stand, durable and sturdy. Paired with anti-slip rubber pads on the screen base for stable use9. Size: about 42.319 x 24.961 x 9.6cmPackage contents:- 18.5-inch screen unit (with integrated stand) x 1- Mini HDMI to HDMI cable (approx. 1.5m) x 1- Type-C dual male connector cable (about 1m) x 1- USB Type-A to Type-C cable (about 1m) x 1- HDMI to Micro HDMI adapter x 1- 20W PD power adapter x 1Specification: Package Weight One Package Weight 0.70kgs / 1.55lb One Package Size 45cm * 27cm * 8cm / 17.72inch * 10.63inch * 3.15inch Qty per Carton 4 Carton Weight 4.00kgs / 8.82lb Carton Size 46cm * 28cm * 34cm / 18.11inch * 11.02inch * 13.39inch Loading Container 20GP: 608 cartons * 4 pcs = 2432 pcs 40HQ: 1413 cartons * 4 pcs = 5652 pcs

Read more less

1. Power supply: NFC wireless power supply 2. Display color: red, yellow, black, white 3. Dot pitch: 0.1943 x 0.1942 mm4. Resolution: 250 x 122 pixels5. Grayscale level: 2 6. Refresh time: 16s (excluding data transmission time) 7. Viewing angle: more than 170 degrees8. Display size: about 48.55 x 23.70mm9. Size: about 6.5 x 4 x 1.3cmFeatures:1. Passive NFC solution, no built-in battery, no need for cumbersome wiring2. When you need to refresh the display, you can use your NFC-enabled smartphone or card reader to wirelessly power up and refresh the display near the ink screen3. Suitable for shopping mall price tags, asset and equipment tags, electronic shelf tags and conference name tags, etc.4. ABS shell, beautiful and thin5. Environmental protection and energy saving, APP operation is simpleSpecification: Package Weight One Package Weight 0.06kgs / 0.14lb One Package Size 10cm * 8cm * 4cm / 3.94inch * 3.15inch * 1.57inch Qty per Carton 160 Carton Weight 10.60kgs / 23.37lb Carton Size 50cm * 38cm * 32cm / 19.69inch * 14.96inch * 12.6inch Loading Container 20GP: 438 cartons * 160 pcs = 70080 pcs 40HQ: 1018 cartons * 160 pcs = 162880 pcs

Read more less

1. Type-C port supports audio and video transmission with plug-and-play functionality, instantly enlarging your phone screen2. Split-screen collaboration on your computer boosts productivity with dual-display operation3. IPS panel ensures superior display performance and color reproduction. 108% sRGB coverage expands red, green, and blue color gamut areas, delivering professional-grade design color accuracy4. HDR true-color quality pursues natural color transitions. Matte screen design minimizes ambient light interference5. 120Hz ultra-high refresh rate screen elevates gaming and movie-watching experiences6. Supports up to 10-point touch (actual touch points depend on software system). Tempered glass panel with 6H hardness. Full-lamination screen for high clarity and dust resistance7. Dual-channel speakers with black magnetic Hi-Fi drivers deliver greater volume, wider sound range, and superior audio performance8. 180° foldable metal stand, durable and sturdy. Paired with anti-slip rubber pads on the screen base for stable use9. Size: about 42.319 x 24.961 x 9.6cmPackage contents:- 18.5-inch screen unit (with integrated stand) x 1- Mini HDMI to HDMI cable (approx. 1.5m) x 1- Type-C dual male connector cable (about 1m) x 1- USB Type-A to Type-C cable (about 1m) x 1- HDMI to Micro HDMI adapter x 1- 20W PD power adapter x 1Specification: Package Weight One Package Weight 0.70kgs / 1.55lb One Package Size 45cm * 27cm * 8cm / 17.72inch * 10.63inch * 3.15inch Qty per Carton 4 Carton Weight 4.00kgs / 8.82lb Carton Size 46cm * 28cm * 34cm / 18.11inch * 11.02inch * 13.39inch Loading Container 20GP: 608 cartons * 4 pcs = 2432 pcs 40HQ: 1413 cartons * 4 pcs = 5652 pcs

Read more less

1. CM5 card holder: for all versions of Compute Module 52. Networking: 1000M Ethernet RJ45 interface, 2500M Ethernet RJ45 interface3. Connector: Raspberry Pi 40PIN GPIO interface4. USB: USB 3.2 Gen1 x 1, USB 2.0 x 4. USB: USB 3.2 Gen1 x 1, USB 2.0 x 25. MIPI: 4-lane MIPI interface x 2 (22PIN 0.5mm FFC connector)6. Video: HDMI connectors x 2, supports dual 4K outputs7. M.2: M.2 M KEY (PCle Gen2/3 x 1)8. Storage: on-board Micro SD card slot (for CM5 version without eMMC)9. Others: on-board EEPROM and encryption chip10. Fan interface: 5V, 4PIN JST-SH PWM fan connector11. Power input: 7V - 36V wide voltage12. Size:- Base plate: about 10.9 x 9.15cm- Case: about 11.46 x 9.15 x 3.29cmFeatures:1. 40PIN GPIO interface and standard CM5 connector on board, support access to Compute Module 5 Lite / eMMC series core boards2. Support M.2 NVMe hard disk, greatly improve the read and write speed of the system or file, support NVMe SSD boot3. Equipped with ETH / MIPI / HDMI / Micro SD / USB / M.2 B KEY / M KEY and other interfaces, more convenient to use4. Careful hole design ensures that each port can fit the motherboard with a high degree of accuracy, and the ports are labeled with a clear silkscreen for easy viewing5. Shell top vents reserved for better heat dissipation6. Wall-mounted holes on both sides of the design, more convenient to install and fix, in the back of the reserved rail mounting screw holes, you can fix the rail (not included)Packing list:- Expansion board x 1- Metal casing x 1- Fan x 1- Power cord x 1- Plug x 4- Screws x 9Specification: Package Weight One Package Weight 0.50kgs / 1.11lb One Package Size 16cm * 12cm * 6cm / 6.3inch * 4.72inch * 2.36inch Qty per Carton 45 Carton Weight 23.50kgs / 51.81lb Carton Size 50cm * 38cm * 32cm / 19.69inch * 14.96inch * 12.6inch Loading Container 20GP: 438 cartons * 45 pcs = 19710 pcs 40HQ: 1018 cartons * 45 pcs = 45810 pcs

Read more less

1. CM5 card holder: for all versions of Compute Module 52. Networking: 1000M Ethernet RJ45 interface, 2500M Ethernet RJ45 interface3. Connector: Raspberry Pi 40PIN GPIO interface4. USB: USB 3.2 Gen1 x 1, USB 2.0 x 4. USB: USB 3.2 Gen1 x 1, USB 2.0 x 25. MIPI: 4-lane MIPI interface x 2 (22PIN 0.5mm FFC connector)6. Video: HDMI connectors x 2, supports dual 4K outputs7. M.2: M.2 M KEY (PCle Gen2/3 x 1)8. Storage: on-board Micro SD card slot (for CM5 version without eMMC)9. Others: on-board EEPROM and encryption chip10. Fan interface: 5V, 4PIN JST-SH PWM fan connector11. Power input: 7V - 36V wide voltage12. Size:- Base plate: about 10.9 x 9.15cm- Case: about 11.46 x 9.15 x 3.29cmFeatures:1. 40PIN GPIO interface and standard CM5 connector on board, support access to Compute Module 5 Lite / eMMC series core boards2. Support M.2 NVMe hard disk, greatly improve the read and write speed of the system or file, support NVMe SSD boot3. Equipped with ETH / MIPI / HDMI / Micro SD / USB / M.2 B KEY / M KEY and other interfaces, more convenient to use4. Careful hole design ensures that each port can fit the motherboard with a high degree of accuracy, and the ports are labeled with a clear silkscreen for easy viewing5. Shell top vents reserved for better heat dissipation6. Wall-mounted holes on both sides of the design, more convenient to install and fix, in the back of the reserved rail mounting screw holes, you can fix the rail (not included)Packing list:- Expansion board x 1- Metal casing x 1- Fan x 1- Power cord x 1- Plug x 4- Screws x 9Specification: Package Weight One Package Weight 0.50kgs / 1.11lb One Package Size 16cm * 12cm * 6cm / 6.3inch * 4.72inch * 2.36inch Qty per Carton 45 Carton Weight 23.50kgs / 51.81lb Carton Size 50cm * 38cm * 32cm / 19.69inch * 14.96inch * 12.6inch Loading Container 20GP: 438 cartons * 45 pcs = 19710 pcs 40HQ: 1018 cartons * 45 pcs = 45810 pcs

Read more less

1. CM5 card holder: for all versions of Compute Module 52. Networking: 1000M Ethernet RJ45 interface, 2500M Ethernet RJ45 interface3. Connector: Raspberry Pi 40PIN GPIO interface4. USB: USB 3.2 Gen1 x 1, USB 2.0 x 4. USB: USB 3.2 Gen1 x 1, USB 2.0 x 25. MIPI: 4-lane MIPI interface x 2 (22PIN 0.5mm FFC connector)6. Video: HDMI connectors x 2, supports dual 4K outputs7. M.2: M.2 M KEY (PCle Gen2/3 x 1)8. Storage: on-board Micro SD card slot (for CM5 version without eMMC)9. Others: on-board EEPROM and encryption chip10. Fan interface: 5V, 4PIN JST-SH PWM fan connector11. Power input: 7V - 36V wide voltage12. Size:- Base plate: about 10.9 x 9.15cm- Case: about 11.46 x 9.15 x 3.29cmFeatures:1. 40PIN GPIO interface and standard CM5 connector on board, support access to Compute Module 5 Lite / eMMC series core boards2. Support M.2 NVMe hard disk, greatly improve the read and write speed of the system or file, support NVMe SSD boot3. Equipped with ETH / MIPI / HDMI / Micro SD / USB / M.2 B KEY / M KEY and other interfaces, more convenient to use4. Careful hole design ensures that each port can fit the motherboard with a high degree of accuracy, and the ports are labeled with a clear silkscreen for easy viewing5. Shell top vents reserved for better heat dissipation6. Wall-mounted holes on both sides of the design, more convenient to install and fix, in the back of the reserved rail mounting screw holes, you can fix the rail (not included)Packing list:- Expansion board x 1- Metal casing x 1- Fan x 1- Power cord x 1- Plug x 4- Screws x 9Specification: Package Weight One Package Weight 0.50kgs / 1.11lb One Package Size 16cm * 12cm * 6cm / 6.3inch * 4.72inch * 2.36inch Qty per Carton 45 Carton Weight 23.50kgs / 51.81lb Carton Size 50cm * 38cm * 32cm / 19.69inch * 14.96inch * 12.6inch Loading Container 20GP: 438 cartons * 45 pcs = 19710 pcs 40HQ: 1018 cartons * 45 pcs = 45810 pcs

Read more less

1. CM5 cradle: for all versions of Compute Module 5 2. Networking: 1000M Ethernet RJ45 interface, 2500M Ethernet RJ45 interface3. Connector: Raspberry Pi 40PIN GPIO interface 4. USB: USB 3.2 Gen1 x 2 5. MIPI: 4-lane MIPI interface x 2 (22PIN 0.5mm FFC connector) 6. Video: HDMI connector x 2, supports dual 4K outputs 7. M.2: M.2 M KEY (PCle Gen2/3 x 1) 8. M.2 (4G /5G): M.2 B KEY, support access to 4G/5G communication module 9. Storage: onboard Micro SD card slot (for CM5 version without eMMC) 10. Fan nterface: 5V, 4PIN JST-SH PWM fan connector11. Power input: 7V - 36V wide voltage (round hole terminal), 5V 5A (Type-C) 12. Size:- Base plate: about 9.96 x 8.7cm)- Housing: about 10.48 x 9 x 2.97cmFeatures:1. 40PIN GPIO interface and standard CM5 connector on board, support access to Compute Module 5 Lite / eMMC series core boards2. Support M.2 NVMe hard disk, greatly improve the read and write speed of the system or file, support NVMe SSD boot3. Equipped with ETH / MIPI / HDMI / Micro SD / USB / M.2 B KEY / M KEY and other interfaces, more convenient to use4. Careful hole design ensures that each port fits the motherboard with clear silkscreen markings on the ports for easy viewing5. Shell reserved vents on the top of the better heat dissipation effect6. Wall-mounted holes on both sides of the design, more convenient to install and fix, in the back of the reserved rail mounting screw holes, you can fix the rail (not included)Packing list:- Expansion board x 1- Metal case x 1- Fan x 1- Power cord x 1- Plug x 4- Screws x 10Specification: Package Weight One Package Weight 0.50kgs / 1.11lb One Package Size 16cm * 12cm * 6cm / 6.3inch * 4.72inch * 2.36inch Qty per Carton 45 Carton Weight 23.50kgs / 51.81lb Carton Size 50cm * 38cm * 32cm / 19.69inch * 14.96inch * 12.6inch Loading Container 20GP: 438 cartons * 45 pcs = 19710 pcs 40HQ: 1018 cartons * 45 pcs = 45810 pcs

Read more less

1. Core board socket: compatible with all versions of RDK X5 MD2. Ethernet: Gigabit Ethernet RJ45 port3. USB: USB 3.0 host ports x 4; Micro USB 2.0 Device port x 1; Micro USB 2.0 (serial debug port)4. Connectors: 40-pin GPIO interface; 10-pin function control I/O5. Display: MIPI-DSI interface (15-pin 1.0mm FPC connector); HDMI interface x 16. Camera: MIPI-CSI (4-lane) interface x 27. Real-time clock: battery-backed interface8. Storage: on-board Micro SD card slot (for RDK X5 MD versions without eMMC)9. Fan Interface: speed-adjustable, speed-measurable, 12V10. Other resources: CAN interface, power switch, PoE interface, etc.11. Power input: 5V 5A12. Size: about 9.9 x 7.9cmSpecification: Package Weight One Package Weight 0.06kgs / 0.14lb One Package Size 12cm * 10cm * 3cm / 4.72inch * 3.94inch * 1.18inch Qty per Carton 144 Carton Weight 10.00kgs / 22.05lb Carton Size 52cm * 38cm * 32cm / 20.47inch * 14.96inch * 12.6inch Loading Container 20GP: 421 cartons * 144 pcs = 60624 pcs 40HQ: 979 cartons * 144 pcs = 140976 pcs

Read more less

1. Type-C port supports audio and video transmission with plug-and-play functionality, instantly enlarging your phone screen2. Split-screen collaboration on your computer boosts productivity with dual-display operation3. IPS panel ensures superior display performance and color reproduction. 108% sRGB coverage expands red, green, and blue color gamut areas, delivering professional-grade design color accuracy4. HDR true-color quality pursues natural color transitions. Matte screen design minimizes ambient light interference5. 120Hz ultra-high refresh rate screen elevates gaming and movie-watching experiences6. Supports up to 10-point touch (actual touch points depend on software system). Tempered glass panel with 6H hardness. Full-lamination screen for high clarity and dust resistance7. Dual-channel speakers with black magnetic Hi-Fi drivers deliver greater volume, wider sound range, and superior audio performance8. 180° foldable metal stand, durable and sturdy. Paired with anti-slip rubber pads on the screen base for stable use9. Size: about 42.319 x 24.961 x 9.6cmPackage contents:- 18.5-inch screen unit (with integrated stand) x 1- Mini HDMI to HDMI cable (approx. 1.5m) x 1- Type-C dual male connector cable (about 1m) x 1- USB Type-A to Type-C cable (about 1m) x 1- HDMI to Micro HDMI adapter x 1- 20W PD power adapter x 1Specification: Package Weight One Package Weight 0.70kgs / 1.55lb One Package Size 45cm * 27cm * 8cm / 17.72inch * 10.63inch * 3.15inch Qty per Carton 4 Carton Weight 4.00kgs / 8.82lb Carton Size 46cm * 28cm * 34cm / 18.11inch * 11.02inch * 13.39inch Loading Container 20GP: 608 cartons * 4 pcs = 2432 pcs 40HQ: 1413 cartons * 4 pcs = 5652 pcs

Read more less

1. CM5 card slot: compatible with all versions of Compute Module 52. Networking: 1000M Ethernet RJ45 port, 2500M Ethernet RJ45 port3. Connectors: raspberry Pi 40-pin GPIO interface4. USB: USB 3.2 Gen1 x 1; USB 2.0 x 25. MIPI: 4-lane MIPI interface x 2 (22-pin 0.5mm FFC connector)6. Video: HDMI interface x 2, supports dual 4K output7. M.2: M.2 M KEY (PCIe Gen2/3 x 1)8. Storage: onboard Micro SD card slot (For CM5 versions without eMMC)9. Fan interface: 5V, 4-pin JST-SH PWM fan connector10. Other: onboard EEPROM and cryptographic chip11. Power input: 7V-36V wide voltage range12. Size:- Base board: about 109.0 x 91.5mm- Enclosure: about 114.6 x 91.5 × 32.9mmFeatures:1. Designed specifically for Raspberry Pi Compute Module 5 core boards2. Onboard 40-pin GPIO interface and standard CM5 connector, supporting integration with Compute Module 5 Lite / eMMC series core boards3. Significantly faster read/write speeds compared to Raspberry Pis Micro SD interface, greatly enhancing system/file access performance; supports booting Raspberry Pi from NVMe SSD4. Expanded connectivity with ETH/MIPI/HDMI/Micro SD/USB/M.2 B KEY/M KEY ports for enhanced usability5. Precision-engineered hole patterns ensure each interface aligns perfectly with the motherboard. Clear silkscreen markings on ports facilitate easy identification6. Integrated cooling fan with ventilation ports on the top cover. Seamless fan integration enhances thermal performance7. Wall-mounting holes on both sides simplify installation and secure mounting. Rail mounting screw holes are provided on the back for rail fixation. Ideal for Raspberry Pi applications in remote communications or other industrial settingsPackage contents:- CM5-DUAL-ETH-BASE x 1- Metal enclosure (Top & Bottom) x 1- CM5-FAN-4010-5V x 1- 12V 4A power supply x 1- Rubber plugs (4PCS) x 1- Screw set x 1Specification: Package Weight One Package Weight 0.50kgs / 1.11lb One Package Size 16cm * 12cm * 6cm / 6.3inch * 4.72inch * 2.36inch Qty per Carton 45 Carton Weight 24.00kgs / 52.91lb Carton Size 50cm * 38cm * 32cm / 19.69inch * 14.96inch * 12.6inch Loading Container 20GP: 438 cartons * 45 pcs = 19710 pcs 40HQ: 1018 cartons * 45 pcs = 45810 pcs

Read more less

1. CM5 card slot: compatible with all versions of Compute Module 52. Networking: 1000M Ethernet RJ45 port, 2500M Ethernet RJ45 port3. Connectors: raspberry Pi 40-pin GPIO interface4. USB: USB 3.2 Gen1 x 1; USB 2.0 x 25. MIPI: 4-lane MIPI interface x 2 (22-pin 0.5mm FFC connector)6. Video: HDMI interface x 2, supports dual 4K output7. M.2: M.2 M KEY (PCIe Gen2/3 x 1)8. Storage: onboard Micro SD card slot (For CM5 versions without eMMC)9. Fan interface: 5V, 4-pin JST-SH PWM fan connector10. Other: onboard EEPROM and cryptographic chip11. Power input: 7V-36V wide voltage range12. Size:- Base board: about 109.0 x 91.5mm- Enclosure: about 114.6 x 91.5 × 32.9mmFeatures:1. Designed specifically for Raspberry Pi Compute Module 5 core boards2. Onboard 40-pin GPIO interface and standard CM5 connector, supporting integration with Compute Module 5 Lite / eMMC series core boards3. Significantly faster read/write speeds compared to Raspberry Pis Micro SD interface, greatly enhancing system/file access performance; supports booting Raspberry Pi from NVMe SSD4. Expanded connectivity with ETH/MIPI/HDMI/Micro SD/USB/M.2 B KEY/M KEY ports for enhanced usability5. Precision-engineered hole patterns ensure each interface aligns perfectly with the motherboard. Clear silkscreen markings on ports facilitate easy identification6. Integrated cooling fan with ventilation ports on the top cover. Seamless fan integration enhances thermal performance7. Wall-mounting holes on both sides simplify installation and secure mounting. Rail mounting screw holes are provided on the back for rail fixation. Ideal for Raspberry Pi applications in remote communications or other industrial settingsPackage contents:- CM5-DUAL-ETH-BASE x 1- Metal enclosure (Top & Bottom) x 1- CM5-FAN-4010-5V x 1- 12V 4A power supply x 1- Rubber plugs (4PCS) x 1- Screw set x 1Specification: Package Weight One Package Weight 0.50kgs / 1.11lb One Package Size 16cm * 12cm * 6cm / 6.3inch * 4.72inch * 2.36inch Qty per Carton 45 Carton Weight 24.00kgs / 52.91lb Carton Size 50cm * 38cm * 32cm / 19.69inch * 14.96inch * 12.6inch Loading Container 20GP: 438 cartons * 45 pcs = 19710 pcs 40HQ: 1018 cartons * 45 pcs = 45810 pcs

Read more less

1. CM5 card slot: compatible with all versions of Compute Module 52. Networking: 1000M Ethernet RJ45 port, 2500M Ethernet RJ45 port3. Connectors: raspberry Pi 40-pin GPIO interface4. USB: USB 3.2 Gen1 x 1; USB 2.0 x 25. MIPI: 4-lane MIPI interface x 2 (22-pin 0.5mm FFC connector)6. Video: HDMI interface x 2, supports dual 4K output7. M.2: M.2 M KEY (PCIe Gen2/3 x 1)8. Storage: onboard Micro SD card slot (For CM5 versions without eMMC)9. Fan interface: 5V, 4-pin JST-SH PWM fan connector10. Other: onboard EEPROM and cryptographic chip11. Power input: 7V-36V wide voltage range12. Size:- Base board: about 109.0 x 91.5mm- Enclosure: about 114.6 x 91.5 × 32.9mmFeatures:1. Designed specifically for Raspberry Pi Compute Module 5 core boards2. Onboard 40-pin GPIO interface and standard CM5 connector, supporting integration with Compute Module 5 Lite / eMMC series core boards3. Significantly faster read/write speeds compared to Raspberry Pis Micro SD interface, greatly enhancing system/file access performance; supports booting Raspberry Pi from NVMe SSD4. Expanded connectivity with ETH/MIPI/HDMI/Micro SD/USB/M.2 B KEY/M KEY ports for enhanced usability5. Precision-engineered hole patterns ensure each interface aligns perfectly with the motherboard. Clear silkscreen markings on ports facilitate easy identification6. Integrated cooling fan with ventilation ports on the top cover. Seamless fan integration enhances thermal performance7. Wall-mounting holes on both sides simplify installation and secure mounting. Rail mounting screw holes are provided on the back for rail fixation. Ideal for Raspberry Pi applications in remote communications or other industrial settingsPackage contents:- CM5-DUAL-ETH-BASE x 1- Metal enclosure (Top & Bottom) x 1- CM5-FAN-4010-5V x 1- 12V 4A power supply x 1- Rubber plugs (4PCS) x 1- Screw set x 1Specification: Package Weight One Package Weight 0.50kgs / 1.11lb One Package Size 16cm * 12cm * 6cm / 6.3inch * 4.72inch * 2.36inch Qty per Carton 45 Carton Weight 24.00kgs / 52.91lb Carton Size 50cm * 38cm * 32cm / 19.69inch * 14.96inch * 12.6inch Loading Container 20GP: 438 cartons * 45 pcs = 19710 pcs 40HQ: 1018 cartons * 45 pcs = 45810 pcs

Read more less

1. Octa-core Cortex A55 64-bit processor with BPU delivering 10 TOPS AI computing power2. Onboard dual-band Wi-Fi and Bluetooth module supporting Bluetooth 5.4 and Wi-Fi 6 for seamless connectivity anytime, anywhere3. Compatible with D-Robotics official base boards4. Supports rich interfaces including HDMI, Gigabit Ethernet, USB 3.0, MIPI CSI, and MIPI DSI for diverse peripheral connectivity5. Integrated PMIC power management IC, DC-DC converter, LPDDR4 memory, and eMMC storage for stable system operationParameters1. Processor: 8-core Cortex A55 64-bit SoC 1.5GHz2. BPU: equivalent to 10 TOPS3. Memory: 4GB4. Flash memory: 32GB5. Display:- 1 x HDMI interface (supporting 1080p 60)- 1 x MIPI DSI (4-lane) interface (supporting 2560 x 1440 60)6. Image: 2 x MIPI CSI (4-lane) camera interfaces7. Multimedia: 4Kp60 H.264 / H.265 (encoding/decoding), MJPEG (encoding/decoding)8. Power input: 5V 5A DC9. Operating temperature: -20°C - 60°C10. Peripheral interfaces:- Supports Gigabit Ethernet- 1 x USB 3.0 interface, 1 x USB 2.0- 8 x UART, 7 x I2C, 4 x SPI, 4 x 10-bit ADC, 2 x I2S, 2 x PDM, 8 x PWM, 8 x LPWM- SD card interface11. Size: about 5.5 x 4cmSpecification: Package Weight One Package Weight 0.08kgs / 0.19lb One Package Size 8cm * 6cm * 4cm / 3.15inch * 2.36inch * 1.57inch Qty per Carton 270 Carton Weight 23.00kgs / 50.71lb Carton Size 50cm * 38cm * 32cm / 19.69inch * 14.96inch * 12.6inch Loading Container 20GP: 438 cartons * 270 pcs = 118260 pcs 40HQ: 1018 cartons * 270 pcs = 274860 pcs

Read more less

1. Main Control Chip: IP23122. Input Voltage: 4.5-5.5V3. Charging Cut-off Voltage: 4.2V/4.35V4. Charging Current: 3A5. Indicator Lights: Red (Working), Green (Fully Charged)6. Dimensions: 32x15x5mm7. Weight: Approximately 3gCharging Modes:1. When the battery voltage is below 3V, it enters trickle charging mode, charging the battery with a 100mA charging current.2. When the battery voltage is above 3V, it enters constant current charging mode, charging the battery with the set constant current.3. When the battery voltage approaches 4.2V and the charging current is less than 300mA, it enters constant voltage charging mode. After entering constant voltage mode, charging stops every four minutes, and the battery voltage is checked to see if it is higher than 4.15V: if it is higher than 4.15V, charging stops; otherwise, charging continues, and the voltage is checked again after another 4 minutes.4. After the battery is fully charged, if the battery voltage is detected to be below 4.1V, charging will resume.Specification: Package Weight One Package Weight 0.01kgs / 0.03lb One Package Size 4cm * 2cm * 1cm / 1.57inch * 0.79inch * 0.39inch Qty per Carton 1800 Carton Weight 19.00kgs / 41.89lb Carton Size 26cm * 22cm * 32cm / 10.24inch * 8.66inch * 12.6inch Loading Container 20GP: 1456 cartons * 1800 pcs = 2620800 pcs 40HQ: 3382 cartons * 1800 pcs = 6087600 pcs

Read more less

1. Based on the RP2350 main control chip, it supports external interfaces such as RS485 and Pico, and features built-in power isolation and optocoupler isolation protection circuits for enhanced safety, stability, and reliability.2. Unique dual-core, dual-architecture design, equipped with a dual-core ARM Cortex-M33 processor and a dual-core Hazard3 RISC-V processor, both running at clock frequencies up to 150MHz, allowing users to flexibly switch between the two architectures.3. 12 programmable I/O (PIO) state machines for custom peripheral support.4. Built-in 520KB SRAM and 16MB on-chip Flash, using a Type-C interface for easy connection.5. Uses high-quality relays, allowing connection to loads: 10A 250V AC or 10A 30V DC.6. On-board isolated RS485 interface for easy connection to various RS485 Modbus industrial expansion modules or sensors.7. On-board Pico-compatible interface, compatible with some Raspberry Pi Pico expansion boards, facilitating the expansion of functions such as RTC, CAN, RS232, LoRa, and sensors.8. On-board terminal block power supply interface, supporting a wide voltage range of 7V~36V, convenient for industrial power supply use.9. On-board optocoupler isolation to prevent high-voltage circuits connected to the relay from interfering with the control chip.10. On-board digital isolation to prevent external signals from interfering with the control chip.11. On-board integrated power isolation provides a stable isolated voltage, requiring no additional power supply at the isolated end.12. On-board power and RS485 transceiver indicator lights, buzzer, and RGB LEDs for easily monitoring the devices operating status.13. On-board power and RS485 transceiver indicator lights, buzzer, and RGB LEDs for easily monitoring the devices operating status.14. DIN rail mountable ABS protective casing for easy installation and enhanced safety.15. USB 1.1 host and device support.16. Supports low-power sleep and hibernation modes.17. Can be recognized as a mass storage device via USB for drag-and-drop program downloading. 18. Provides 34 multi-functional GPIO pins19. Pins include 1 HSTX, 2 I2C, 2 UART, 8 12-bit ADC, and 24 controllable PWM channelsProduct parameters:1. Power supply voltage: 5V2. Functions: device power supply, USB communication, and firmware download, etc.3. Interface type: terminal block4. Direction control: hardware automatically detects and controls data transmission direction5. Interface protection: provides TVS tube protection, surge and electrostatic protection6. Matching resistor: default NC, 120R matching resistor reserved, can be enabled by jumper cap7. Contact type: one normally open, one normally closed8. Isolation type: optocoupler isolation9. RGB: colorful cool LED beads, customizable display colors10. PWR: power indicator light, lights up red when USB is connected and voltage is detected11. TXD: transmit indicator light, lights up green when data is sent from the RS485 interface12. RXD: receive indicator light, lights up blue when data is received from the RS485 interface13. Power dupply range: 7V-36V14. Casing: rail-mounted ABS protective casing15. Dimensions: 145 x 90 x 40 mmSpecification: Package Weight One Package Weight 0.07kgs / 0.16lb One Package Size 17cm * 12cm * 6cm / 6.69inch * 4.72inch * 2.36inch Qty per Carton 30 Carton Weight 3.20kgs / 7.05lb Carton Size 36cm * 38cm * 32cm / 14.17inch * 14.96inch * 12.6inch Loading Container 20GP: 609 cartons * 30 pcs = 18270 pcs 40HQ: 1414 cartons * 30 pcs = 42420 pcs

Read more less

1. Power supply voltage: 3.3V/5V2. Operating current: 20mA@5V3. Wavelength range: 8μm ~ 14μm4. Refresh rate: 25 FPS (Max)5. Field of view: standard version 55 degrees (D) x 44 degrees (H) x 35 degrees (V); Wide-angle version 143 degrees (D) x 90 degrees (H) x 66 degrees (V)6. Noise equivalent temperature difference: 150mK7. Can be connected to development boards such as Raspberry Pi via SPI and I2C.8. This module combines the advantages of microbolometer and thermopile pixel technology, achieving simultaneous optimization of accuracy and reliability.9. Product dimensions: 45x22mm10. This product is a far-infrared thermal imaging sensor, using a hybrid technology of microbolometer and thermopile pixels, with an 80×62 pixel focal plane array. It breaks the limitations of traditional temperature measurement devices' "single-point detection" and "dependence on lighting," providing devices in industrial, consumer electronics, security, and medical fields with the core ability to "see temperature distribution," serving as the hardware support for intelligent temperature monitoring and risk early warning.Main applications:1. Long-term non-contact object temperature online monitoring solutions2. Infrared thermal imager, infrared thermometer3. Smart home, smart building, smart lighting4. Infant and elderly care5. Fever detection6. Industrial temperature control, security, intrusion/motion detection7. Small target thermal analysis, key points and solutions for thermal trend analysisMain functional features:1. Uses microbolometer and thermopile hybrid technology, with 80 (H) × 62 (V) pixels2. Shutterless design, supports continuous operation and thermal image video streaming3. Each pixel is factory calibrated to ensure uniformity and accuracy of temperature readings 4. Features a Noise Equivalent Temperature Difference (NETD) of 150mK RMS @ 1Hz refresh rate, resulting in excellent noise performance.5. Supports thermal imaging video stream output at a frame rate of up to 25 FPS (Max).6. Multiple lenses available with different fields of view.7. Provides comprehensive supporting documentation and manuals (including Raspberry Pi and Python example programs).Specification: Package Weight One Package Weight 0.07kgs / 0.16lb One Package Size 8cm * 6cm * 5cm / 3.15inch * 2.36inch * 1.97inch Qty per Carton 216 Carton Weight 16.30kgs / 35.93lb Carton Size 50cm * 38cm * 32cm / 19.69inch * 14.96inch * 12.6inch Loading Container 20GP: 438 cartons * 216 pcs = 94608 pcs 40HQ: 1018 cartons * 216 pcs = 219888 pcs

Read more less

1. Based on the RP2350 main controller, it supports external interfaces such as RS485 and Pico, and features built-in power isolation and optocoupler isolation protection circuits for enhanced safety, stability, and reliability.2. Unique dual-core, dual-architecture design, equipped with a dual-core ARM Cortex-M33 processor and a dual-core Hazard3 RISC-V processor, both operating at clock frequencies up to 150MHz, allowing users to flexibly switch between the two architectures.3. Equipped with a Raspberry Pi Radio Module 2, supporting Wi-Fi 4 wireless network and Bluetooth 5.2 (Wi-Fi module version only).4. Built-in 520KB SRAM and 16MB on-chip Flash. Uses a Type-C interface, eliminating concerns about correct plug orientation.5. Uses high-quality relays, allowing connection to loads: 10A 250V AC or 10A 30V DC.6. On-board isolated RS485 interface for easy connection to various RS485 Modbus industrial expansion modules or sensors.7. On-board Pico-compatible interface, compatible with some Raspberry Pi Pico expansion boards, facilitating the expansion of functions such as RTC, CAN, RS232, LoRa, and sensors.8. On-board terminal block power supply interface, supporting a wide voltage range of 7V~36V, convenient for industrial power supply use.9. On-board optocoupler isolation to prevent high-voltage circuits connected to the relay from interfering with the control chip.10. On-board digital isolation to prevent external signals from interfering with the control chip.11. On-board integrated power isolation provides a stable isolated voltage; no additional power supply is required for the isolated end.12. On-board power and RS485 transceiver indicator lights, buzzer, and RGB LEDs for easy monitoring of the devices operating status.13. On-board power and RS485 transceiver indicator lights, buzzer, and RGB LEDs for easy monitoring of the devices operating status.14. Rail-mounted ABS protective casing for easy installation and safer use.15. USB 1.1 host and device support.16. Supports low-power sleep and hibernation modes.17. Controllable via USB. Identified as a mass storage device for drag-and-drop program downloading18. 34 multi-functional GPIO pins19. 1 HSTX pin, 2 I2C pins, 2 UART pins, 8 12-bit ADC pins, and 24 controllable PWM channels20. 12 programmable I/O (PIO) state machines for custom peripheral supportProduct parameters:1. Power supply voltage: 5V2. Functions: device power supply, USB communication, and firmware download, etc.3. Interface type: terminal block4. Direction control: hardware automatically detects and controls data transmission direction5. Interface protection: provides TVS tube protection, surge and electrostatic protection6. Matching resistor: default NC, 120R matching resistor reserved, can be enabled with a jumper cap7. Contact type: one normally open, one normally closed8. Isolation type: optocoupler isolation9. RGB: colorful cool LED beads, customizable display colors10. PWR: power indicator light, lights up red when USB is connected and voltage is detected11. TXD: transmit indicator light, lights up green when data is sent from the RS485 interface12. RXD: receive indicator light, lights up blue when data is received from the RS485 interface13. Power supply range: 7V-36V14. Casing: rail-mounted ABS protective casing15. Dimensions: 145 x 90 x 40 mmSpecification: Package Weight One Package Weight 0.07kgs / 0.16lb One Package Size 17cm * 12cm * 6cm / 6.69inch * 4.72inch * 2.36inch Qty per Carton 30 Carton Weight 3.20kgs / 7.05lb Carton Size 36cm * 38cm * 32cm / 14.17inch * 14.96inch * 12.6inch Loading Container 20GP: 609 cartons * 30 pcs = 18270 pcs 40HQ: 1414 cartons * 30 pcs = 42420 pcs

Read more less

1. Networking: 1000M Ethernet RJ45 interface; 2500M Ethernet RJ45 interface2. Connector: Raspberry Pi 40PIN GPIO interface3. USB: USB 3.2 Gen1 x 24. MIPI: 4-lane MIPI interface × 2 (22PIN 0.5mm FFC connector)5. Video: HDMI interface x 2, supports dual 4K output6. M.2: M.2 M KEY (PCIe Gen2/3 x1)7. M.2 (4G/5G): B KEY, supports 4G/5G communication module8. Storage: Onboard Micro SD card slot (for CM5 versions without eMMC)9. Fan Interface: 5V, 4PIN JST-SH PWM fan connector10. Power Input: 7V ~36V wide voltage (round terminal), 5V 5A (Type-C)11. Supports 4-screen display, with added MIPI DSI driver; the system will default to connecting to the screens regardless of whether they are connected, and the screens will display in split-screen mode (this depends on the system version).12. Dimensions: 99.60 x 87.00 mmSpecification: Package Weight One Package Weight 0.06kgs / 0.14lb One Package Size 12cm * 12cm * 4cm / 4.72inch * 4.72inch * 1.57inch Qty per Carton 96 Carton Weight 6.90kgs / 15.21lb Carton Size 50cm * 38cm * 34cm / 19.69inch * 14.96inch * 13.39inch Loading Container 20GP: 412 cartons * 96 pcs = 39552 pcs 40HQ: 958 cartons * 96 pcs = 91968 pcs

Read more less

1. Power supply voltage: 3.3V/5V2. Operating current: 20mA@5V3. Wavelength range: 8μm ~ 14μm4. Refresh rate: 25 FPS (Max)5. Field of view: standard version 55 degrees (D) x 44 degrees (H) x 35 degrees (V); Wide-angle version 143 degrees (D) x 90 degrees (H) x 66 degrees (V)6. Noise equivalent temperature difference: 150mK7. Can be connected to development boards such as Raspberry Pi via SPI and I2C.8. This module combines the advantages of microbolometer and thermopile pixel technology, achieving simultaneous optimization of accuracy and reliability.9. Product dimensions: 45x22mm10. This product is a far-infrared thermal imaging sensor, using a hybrid technology of microbolometer and thermopile pixels, with an 80×62 pixel focal plane array. It breaks the limitations of traditional temperature measurement devices "single-point detection" and "dependence on lighting," providing devices in industrial, consumer electronics, security, and medical fields with the core ability to "see temperature distribution," serving as the hardware support for intelligent temperature monitoring and risk early warning.Main applications:1. Long-term non-contact object temperature online monitoring solutions2. Infrared thermal imager, infrared thermometer3. Smart home, smart building, smart lighting4. Infant and elderly care5. Fever detection6. Industrial temperature control, security, intrusion/motion detection7. Small target thermal analysis, key points and solutions for thermal trend analysisMain functional features:1. Uses microbolometer and thermopile hybrid technology, with 80 (H) × 62 (V) pixels2. Shutterless design, supports continuous operation and thermal image video streaming3. Each pixel is factory calibrated to ensure uniformity and accuracy of temperature readings 4. Features a Noise Equivalent Temperature Difference (NETD) of 150mK RMS @ 1Hz refresh rate, resulting in excellent noise performance.5. Supports thermal imaging video stream output at a frame rate of up to 25 FPS (Max).6. Multiple lenses available with different fields of view.7. Provides comprehensive supporting documentation and manuals (including Raspberry Pi and Python example programs).Specification: Package Weight One Package Weight 0.07kgs / 0.16lb One Package Size 8cm * 6cm * 5cm / 3.15inch * 2.36inch * 1.97inch Qty per Carton 216 Carton Weight 16.30kgs / 35.93lb Carton Size 50cm * 38cm * 32cm / 19.69inch * 14.96inch * 12.6inch Loading Container 20GP: 438 cartons * 216 pcs = 94608 pcs 40HQ: 1018 cartons * 216 pcs = 219888 pcs

Read more less

1. Display size: 160.0 x 96.0 mm2. Dimensions: 154.0 x 214.0 x 32 mm3. Screen pixel pitch: 0.2 x 0.2 mm4. Screen resolution: 800 x 4805. Display colors: black, white, green, blue, red, yellow6. Grayscale levels: 27. Refresh time: 12s8. Sleep current: 1mA9. Charging voltage/operating voltage: 5V10. Equipped with a high-performance Xtensa 32-bit LX7 dual-core processor with a main frequency of up to 240MHz11. Supports 2.4GHz Wi-Fi and Bluetooth 5 (LE), with an onboard internal antenna12. Built-in 512KB SRAM and 384KB ROM, integrated with 16MB Flash and 8MB PSRAM13. Onboard audio codec chip, supporting voice acquisition and playback, facilitating AI voice interaction applications14. The screen uses E Ink Spectra 6 (E6) technology, supporting high-contrast and high-saturation color display effects15. Six primary colors use dithering technology to produce full-color images; overall power consumption is very low, consuming power only during refresh16. Large-capacity lithium battery with power-saving circuit; one charge can provide thousands of refreshes (without external high-power devices such as speakers)17. Onboard PCF85063 RTC real-time clock and SHTC3 temperature and humidity sensor for accurate RTC time management and temperature and humidity monitoring18. Simple solid wood photo frame, elegant and beautiful19. Rotating stand and hook for unrestricted use scenarios20. Open source code, freely customizable functions21. An e-paper AloT photo frame with an onboard ESP32-S3 microcontroller, supporting Wi-Fi and BLE dual-mode communication22. Equipped with a 7.3-inch e-paper screen, extremely low power consumption, suitable for portable devices and long-battery-life scenarios23. Integrated with RTC real-time clock, SHTC3 temperature and humidity sensor, microSD card slot, low-power audio codec chip circuit, and lithium battery charging and discharging management circuit.24. Onboard audio decoding chip, supporting high-quality audio processing, providing clear and high-quality audio input and output.25. Supports AI and can connect to online large language model platforms.26. Features a high-quality solid wood frame and a versatile white inner lining, offering a simple yet stylish design.Specification: Package Weight One Package Weight 0.60kgs / 1.33lb One Package Size 18cm * 24cm * 6cm / 7.09inch * 9.45inch * 2.36inch Qty per Carton 20 Carton Weight 13.10kgs / 28.88lb Carton Size 50cm * 38cm * 32cm / 19.69inch * 14.96inch * 12.6inch Loading Container 20GP: 438 cartons * 20 pcs = 8760 pcs 40HQ: 1018 cartons * 20 pcs = 20360 pcs

Read more less

1. Size: 13.3 Inch2. Viewing angle: 178 Degrees3. Resolution: 1920x1080 Pixels4. Dimensions: 307.00(H)×183.00(V)×10.00(D)mm5. Display area: 293.65(H)×165.70(V)mm6. Pixel pitch: 0.153(H) x 0.153(V)mm7. Color gamut: 99% NTSC8. Brightness: 300cd/m2 (MAX)9. Contrast ratio: 100000:110. Backlight adjustment: OSD / DDCCI11. Refresh rate: 60Hz12. Display interface: mini HDMI / Type-C13. Power interface: 5V Power Supply14. Weight: 676g15. 13.3-inch AMOLED touchscreen, 1920x1080 hardware resolution16. 10-point capacitive touch, with tempered glass panel, hardness up to 6H17. Uses full lamination touch technology for better display effect18. When used with Raspberry Pi, supports Raspberry Pi OS / Ubuntu / Kali and Retropie19. When used as a computer monitor, supports Windows 11 / 10 / 8.1 / 8 / 720. Supports multi-language OSD menu (for power control, brightness/contrast adjustment, etc.)21. Built-in high-fidelity speakers, with 3.5mm audio jack, supports HDMI audio output22. All-metal CNC alloy casingSpecification: Package Weight One Package Weight 0.70kgs / 1.55lb One Package Size 32cm * 21cm * 12cm / 12.6inch * 8.27inch * 4.72inch Qty per Carton 2 Carton Weight 2.50kgs / 5.51lb Carton Size 34cm * 23cm * 26cm / 13.39inch * 9.06inch * 10.24inch Loading Container 20GP: 1311 cartons * 2 pcs = 2622 pcs 40HQ: 3044 cartons * 2 pcs = 6088 pcs

Read more less

1. Size: 13.3 Inch2. Viewing angle: 178 Degrees3. Resolution: 1920x1080 Pixels4. Dimensions: 307.00(H)×183.00(V)×10.00(D)mm5. Display area: 293.65(H)×165.70(V)mm6. Pixel pitch: 0.153(H) x 0.153(V)mm7. Color gamut: 99% NTSC8. Brightness: 300cd/m2 (MAX)9. Contrast ratio: 100000:110. Backlight adjustment: OSD / DDCCI11. Refresh rate: 60Hz12. Display interface: mini HDMI / Type-C13. Power interface: 5V Power Supply14. Weight: 676g15. 13.3-inch AMOLED touchscreen, 1920x1080 hardware resolution16. 10-point capacitive touch, with tempered glass panel, hardness up to 6H17. Uses full lamination touch technology for better display effect18. When used with Raspberry Pi, supports Raspberry Pi OS / Ubuntu / Kali and Retropie19. When used as a computer monitor, supports Windows 11 / 10 / 8.1 / 8 / 720. Supports multi-language OSD menu (for power control, brightness/contrast adjustment, etc.)21. Built-in high-fidelity speakers, with 3.5mm audio jack, supports HDMI audio output22. All-metal CNC alloy casingSpecification: Package Weight One Package Weight 0.70kgs / 1.55lb One Package Size 32cm * 21cm * 12cm / 12.6inch * 8.27inch * 4.72inch Qty per Carton 2 Carton Weight 2.50kgs / 5.51lb Carton Size 34cm * 23cm * 26cm / 13.39inch * 9.06inch * 10.24inch Loading Container 20GP: 1311 cartons * 2 pcs = 2622 pcs 40HQ: 3044 cartons * 2 pcs = 6088 pcs

Read more less

1. The 10.1-DSI-TOUCH-B is a portrait-oriented touchscreen LCD display designed for interactive projects such as tablets, entertainment systems, and information dashboards.2. IPS display panel with excellent display performance and a 170-degree viewing angle.3. Utilizes high-color gamut quantum dot technology for a wider color gamut and purer colors.4. Supports 10-point touch; the actual number of touch points depends on the software system.5. Tempered glass panel with a hardness of 6H.6. DSI interface drives the LCD with a refresh rate of up to 60Hz.7. Supports backlight brightness control via software.8. Aluminum alloy back shell design with purely passive cooling.9. Dimensions: 245.8 x 153.58 x 12.75 mmAccessories ist:- 10.1-inch display x 1- MIPI-DSI-Cable-12cm x 1- MX 1.25 2PIN to 2.54 3PIN connector cable x 1- FFC cable 22PIN approximately 200mm (opposite direction) x 2- MX1.25 2PIN to MX1.25 4PIN approximately 150mm x 1- Copper pillar kit x 1Specification: Package Weight One Package Weight 0.70kgs / 1.55lb One Package Size 27cm * 18cm * 4cm / 10.63inch * 7.09inch * 1.57inch Qty per Carton 16 Carton Weight 12.30kgs / 27.12lb Carton Size 29cm * 38cm * 34cm / 11.42inch * 14.96inch * 13.39inch Loading Container 20GP: 711 cartons * 16 pcs = 11376 pcs 40HQ: 1652 cartons * 16 pcs = 26432 pcs

Read more less

1. Size: 13.3 Inch2. Viewing angle: 178 Degrees3. Resolution: 1920x1080 Pixels4. Dimensions: 307.00(H)×183.00(V)×10.00(D)mm5. Display area: 293.65(H)×165.70(V)mm6. Pixel pitch: 0.153(H) x 0.153(V)mm7. Color gamut: 99% NTSC8. Brightness: 300cd/m2 (MAX)9. Contrast ratio: 100000:110. Backlight adjustment: OSD / DDCCI11. Refresh rate: 60Hz12. Display interface: mini HDMI / Type-C13. Power interface: 5V Power Supply14. Weight: 676g15. 13.3-inch AMOLED touchscreen, 1920x1080 hardware resolution16. 10-point capacitive touch, with tempered glass panel, hardness up to 6H17. Uses full lamination touch technology for better display effect18. When used with Raspberry Pi, supports Raspberry Pi OS / Ubuntu / Kali and Retropie19. When used as a computer monitor, supports Windows 11 / 10 / 8.1 / 8 / 720. Supports multi-language OSD menu (for power control, brightness/contrast adjustment, etc.)21. Built-in high-fidelity speakers, with 3.5mm audio jack, supports HDMI audio output22. All-metal CNC alloy casingSpecification: Package Weight One Package Weight 0.70kgs / 1.55lb One Package Size 32cm * 21cm * 12cm / 12.6inch * 8.27inch * 4.72inch Qty per Carton 2 Carton Weight 2.50kgs / 5.51lb Carton Size 34cm * 23cm * 26cm / 13.39inch * 9.06inch * 10.24inch Loading Container 20GP: 1311 cartons * 2 pcs = 2622 pcs 40HQ: 3044 cartons * 2 pcs = 6088 pcs

Read more less

1. The ESP32-S3-Touch-LCD-1.83 is a high-performance, highly integrated microcontroller development board. 1. In a compact form factor, the board integrates a 1.83-inch capacitive LCD screen, a highly integrated power management chip, a six-axis sensor (three-axis accelerometer and three-axis gyroscope), RTC, and a low-power audio codec chip, facilitating development and embedding into products.2. Equipped with ESP32-S3R8 high-performance Xtensa 32-bit LX7 dual-core processor, with a clock speed up to 240MHz.3. Supports 2.4GHz Wi-Fi (802.11 b/g/n) and Bluetooth 5 (LE), with an onboard antenna.4. Built-in 512KB SRAM and 384KB ROM, stacked 8MB PSRAM and external 16MB Flash.5. Uses a Type-C interface, improving user convenience and device compatibility.6. Onboard 1.83-inch capacitive touch LCD screen, 240 × 284 resolution, 65K colors.7. Built-in ST7789P driver chip and CST816D capacitive touch chip, communicating via SPI and I2C interfaces respectively, without occupying excessive interface pins.8. Onboard QMI8658 six-axis inertial measurement unit (3-axis acceleration, 3-axis gyroscope), capable of detecting motion posture, step counting, and other functions.9. Onboard PCF85063 RTC chip, connected to the battery via AXP2101 for uninterrupted power supply.10. Onboard PWR and BOOT side buttons with customizable functions, facilitating custom function development using the buttons.11. Onboard JST 1.2mm lithium battery charging and discharging interface.12. Provides 1 I2C, 1 UART, and 1 USB solder pads for external devices and debugging, allowing flexible configuration of peripheral functions.13. Onboard micro SD card slot, supporting storage expansion and fast data transfer, facilitating data recording and media playback functions, and simplifying system circuit design.14. AXP2101 provides efficient power management solutions, supports multiple configurable voltage outputs, integrates charging and battery management functions, and helps extend battery life.15. High touch screen transmittance, fast response, and long lifespan16. Display panel: IPS17. Display size: 1.83 inches18. Display resolution: 240 x 284 pixels19. Display colors: 65K20. Display brightness: 300 cd/㎡21. Contrast ratio: 1200:122. Communication interface: SPI23. Driver IC: ST7789P24. Touch control: supported25. Touch control IC: CST816DSpecification: Package Weight One Package Weight 0.10kgs / 0.23lb One Package Size 8cm * 8cm * 4cm / 3.15inch * 3.15inch * 1.57inch Qty per Carton 192 Carton Weight 20.30kgs / 44.75lb Carton Size 50cm * 34cm * 34cm / 19.69inch * 13.39inch * 13.39inch Loading Container 20GP: 461 cartons * 192 pcs = 88512 pcs 40HQ: 1071 cartons * 192 pcs = 205632 pcs

Read more less

1. The ESP32-S3-Touch-LCD-1.83 is a high-performance, highly integrated microcontroller development board. 1. In a compact form factor, the board integrates a 1.83-inch capacitive LCD screen, a highly integrated power management chip, a six-axis sensor (three-axis accelerometer and three-axis gyroscope), RTC, and a low-power audio codec chip, facilitating development and embedding into products.2. Equipped with ESP32-S3R8 high-performance Xtensa 32-bit LX7 dual-core processor, with a clock speed up to 240MHz.3. Supports 2.4GHz Wi-Fi (802.11 b/g/n) and Bluetooth 5 (LE), with an onboard antenna.4. Built-in 512KB SRAM and 384KB ROM, stacked 8MB PSRAM and external 16MB Flash.5. Uses a Type-C interface, improving user convenience and device compatibility.6. Onboard 1.83-inch capacitive touch LCD screen, 240 × 284 resolution, 65K colors.7. Built-in ST7789P driver chip and CST816D capacitive touch chip, communicating via SPI and I2C interfaces respectively, without occupying excessive interface pins.8. Onboard QMI8658 six-axis inertial measurement unit (3-axis acceleration, 3-axis gyroscope), capable of detecting motion posture, step counting, and other functions.9. Onboard PCF85063 RTC chip, connected to the battery via AXP2101 for uninterrupted power supply.10. Onboard PWR and BOOT side buttons with customizable functions, facilitating custom function development using the buttons.11. Onboard JST 1.2mm lithium battery charging and discharging interface.12. Provides 1 I2C, 1 UART, and 1 USB solder pads for external devices and debugging, allowing flexible configuration of peripheral functions.13. Onboard micro SD card slot, supporting storage expansion and fast data transfer, facilitating data recording and media playback functions, and simplifying system circuit design.14. AXP2101 provides efficient power management solutions, supports multiple configurable voltage outputs, integrates charging and battery management functions, and helps extend battery life.15. High touch screen transmittance, fast response, and long lifespan16. Display panel: IPS17. Display size: 1.83 inches18. Display resolution: 240 x 284 pixels19. Display colors: 65K20. Display brightness: 300 cd/㎡21. Contrast ratio: 1200:122. Communication interface: SPI23. Driver IC: ST7789P24. Touch control: supported25. Touch control IC: CST816DSpecification: Package Weight One Package Weight 0.10kgs / 0.23lb One Package Size 8cm * 8cm * 4cm / 3.15inch * 3.15inch * 1.57inch Qty per Carton 192 Carton Weight 20.30kgs / 44.75lb Carton Size 50cm * 34cm * 34cm / 19.69inch * 13.39inch * 13.39inch Loading Container 20GP: 461 cartons * 192 pcs = 88512 pcs 40HQ: 1071 cartons * 192 pcs = 205632 pcs

Read more less

1. Camera input: expands two CSI interfaces for AI applications such as facial recognition, road sign detection, line recognition, and license plate recognition2. 7 USB Ports: 4 Type-A + 1 Type-C + 2 USB 2.0 ribbon cables for diverse peripherals. USB 3.2 Gen 2 port supports up to 10Gbps data transfer; Type-C port enables system flashing3. 4K HD Output via DisplayPort interface4. Color-coded 40-pin GPIO interface for expanding I2C, SPI, I2S, UART, and GPIO resources5. Flexible storage and wireless expansion: Base board features two M.2 Key M slots for SSDs and an M.2 Key E interface for wireless network cards, minimizing cable clutter6. Size: about 10.3 x 9.05 cmSpecification: Package Weight One Package Weight 0.09kgs / 0.21lb One Package Size 12cm * 12cm * 2cm / 4.72inch * 4.72inch * 0.79inch Qty per Carton 210 Carton Weight 20.00kgs / 44.09lb Carton Size 50cm * 38cm * 35cm / 19.69inch * 14.96inch * 13.78inch Loading Container 20GP: 401 cartons * 210 pcs = 84210 pcs 40HQ: 930 cartons * 210 pcs = 195300 pcs

Read more less

1. Features the RP2350B microcontroller chip designed by Raspberry Pi.2. Unique dual-core, dual-architecture design, equipped with a dual-core ARM Cortex-M33 processor and a dual-core Hazard3 RISC-V processor, both running at up to 150MHz, allowing users to flexibly switch between the two architectures.3. Built-in 520KB of SRAM and 16MB of on-chip Flash.4. Uses a Type-C interface, eliminating concerns about correct plug orientation.5. Uses high-quality relays, allowing connection of loads: 10A 250V AC or 10A 30V DC.6. Digital input with bidirectional optocoupler isolation, supporting passive and active digital inputs; relays support control in conjunction with switch inputs.7. On-board isolated RS485 interface for easy connection to various RS485 Modbus industrial expansion modules or sensors.8. On-board pin header interface for connecting other devices.9. On-board terminal block power interface, supporting a wide voltage range of 7~36V, convenient for industrial power supply.10. On-board RTC clock chip, supporting scheduled tasks.11. On-board W5500 Ethernet chip, extending 10/100Mbps network connectivity via SPI interface.12. PoE Ethernet port version supports external PoE modules for Power over Ethernet functionality (compliant with IEEE 802.3af standard).13. On-board optocoupler isolation to prevent high-voltage circuits connected to the relays from interfering with the control chip.14. On-board digital isolation to prevent external signals from interfering with the control chip.15. On-board integrated power isolation, providing stable isolated voltage; no additional power supply is required for the isolated end.16. On-board Micro SD card slot for external SD card storage of images or files.17. On-board buzzer, RGB LED, and power and RS485 transceiver indicator lights for easy monitoring of device operating status.18. DIN rail mountable ABS protective casing for easy installation and safer use.19. USB 1.1 host and device support.20. Supports low-power sleep and hibernation modes21. Can be recognized as a mass storage device via USB for drag-and-drop program download22. 15 multi-functional GPIO pins23. 2 SPI, 2 I2C, 2 UART, 8 12-bit ADCs, and 12 controllable PWM channels14. Precise on-chip clock and timers, temperature sensor, on-chip accelerated floating-point library15. 12 programmable I/O (PIO) state machines for custom peripheral support16. Built-in power isolation, optocoupler isolation and other protection circuits for safety, stability and reliability17. Dimensions: 175x90x40mmProduct parameters:- USB interface1. Interface type: USB Type-C2. Power supply voltage: 5V3. Functions: device power supply, USB communication and firmware download, etc.- Isolated communication Interface1. Interface type: RS4852. Interface form: terminal block3. Direction control: hardware automatic detection and control of data transmission direction4. Interface protection: provides TVS tube protection, surge and electrostatic protection5. Matching resistor: default NC, 120R matching resistor reserved, can be enabled by jumper cap- Digital Input1. Number of inputs: 8 channels2. Input voltage range: 5V ~ 36V3. Input type: passive input / active input (NPN type or PNP type)4. Isolation type: Bidirectional optocoupler isolation- Relay1. Number of channels: 8 channels2. Contact type: one normally open, one normally closed3. Isolation type: optocoupler isolation- Indicator lights1. RGB: colorful cool LED beads, customizable display color2. PWR: power indicator light, lights up red when USB is connected and voltage is detected3. TXD: transmit indicator light, lights up green when data is sent from the RS485 interface4. RXD: receive indicator light, lights up when data is received from RS485 The blue light illuminates when the interface receives data.5. Power supply range: 7V ~ 36VSpecification: Package Weight One Package Weight 0.34kgs / 0.76lb One Package Size 20cm * 12cm * 6cm / 7.87inch * 4.72inch * 2.36inch Qty per Carton 30 Carton Weight 11.30kgs / 24.91lb Carton Size 42cm * 38cm * 32cm / 16.54inch * 14.96inch * 12.6inch Loading Container 20GP: 522 cartons * 30 pcs = 15660 pcs 40HQ: 1212 cartons * 30 pcs = 36360 pcs

Read more less

1. Features the RP2350B microcontroller chip designed by Raspberry Pi.2. Unique dual-core, dual-architecture design, equipped with a dual-core ARM Cortex-M33 processor and a dual-core Hazard3 RISC-V processor, both running at up to 150MHz, allowing users to flexibly switch between the two architectures.3. Built-in 520KB of SRAM and 16MB of on-chip Flash.4. Uses a Type-C interface, eliminating concerns about correct plug orientation.5. Uses high-quality relays, allowing connection of loads: 10A 250V AC or 10A 30V DC.6. Digital input with bidirectional optocoupler isolation, supporting passive and active digital inputs; relays support control in conjunction with switch inputs.7. On-board isolated RS485 interface for easy connection to various RS485 Modbus industrial expansion modules or sensors.8. On-board pin header interface for connecting other devices.9. On-board terminal block power interface, supporting a wide voltage range of 7~36V, convenient for industrial power supply.10. On-board RTC clock chip, supporting scheduled tasks.11. On-board W5500 Ethernet chip, extending 10/100Mbps network connectivity via SPI interface.12. PoE Ethernet port version supports external PoE modules for Power over Ethernet functionality (compliant with IEEE 802.3af standard).13. On-board optocoupler isolation to prevent high-voltage circuits connected to the relays from interfering with the control chip.14. On-board digital isolation to prevent external signals from interfering with the control chip.15. On-board integrated power isolation, providing stable isolated voltage; no additional power supply is required for the isolated end.16. On-board Micro SD card slot for external SD card storage of images or files.17. On-board buzzer, RGB LED, and power and RS485 transceiver indicator lights for easy monitoring of device operating status.18. DIN rail mountable ABS protective casing for easy installation and safer use.19. USB 1.1 host and device support.20. Supports low-power sleep and hibernation modes21. Can be recognized as a mass storage device via USB for drag-and-drop program download22. 15 multi-functional GPIO pins23. 2 SPI, 2 I2C, 2 UART, 8 12-bit ADCs, and 12 controllable PWM channels14. Precise on-chip clock and timers, temperature sensor, on-chip accelerated floating-point library15. 12 programmable I/O (PIO) state machines for custom peripheral support16. Built-in power isolation, optocoupler isolation and other protection circuits for safety, stability and reliability17. Dimensions: 175x90x40mmProduct parameters:- USB interface1. Interface type: USB Type-C2. Power supply voltage: 5V3. Functions: device power supply, USB communication and firmware download, etc.- Isolated communication Interface1. Interface type: RS4852. Interface form: terminal block3. Direction control: hardware automatic detection and control of data transmission direction4. Interface protection: provides TVS tube protection, surge and electrostatic protection5. Matching resistor: default NC, 120R matching resistor reserved, can be enabled by jumper cap- Digital Input1. Number of inputs: 8 channels2. Input voltage range: 5V ~ 36V3. Input type: passive input / active input (NPN type or PNP type)4. Isolation type: Bidirectional optocoupler isolation- Relay1. Number of channels: 8 channels2. Contact type: one normally open, one normally closed3. Isolation type: optocoupler isolation- Indicator lights1. RGB: colorful cool LED beads, customizable display color2. PWR: power indicator light, lights up red when USB is connected and voltage is detected3. TXD: transmit indicator light, lights up green when data is sent from the RS485 interface4. RXD: receive indicator light, lights up when data is received from RS485 The blue light illuminates when the interface receives data.5. Power supply range: 7V ~ 36VSpecification: Package Weight One Package Weight 0.34kgs / 0.76lb One Package Size 20cm * 12cm * 6cm / 7.87inch * 4.72inch * 2.36inch Qty per Carton 30 Carton Weight 11.30kgs / 24.91lb Carton Size 42cm * 38cm * 32cm / 16.54inch * 14.96inch * 12.6inch Loading Container 20GP: 522 cartons * 30 pcs = 15660 pcs 40HQ: 1212 cartons * 30 pcs = 36360 pcs

Read more less

1. Pixels: 13 million2. Photographic chip: SC132GS3. Photographic element size: 1/4 inch4. Aperture: 2.0F5. Resolution: 1280 x 1080 (per channel)6. Focal length (BFL): 1.75mm7. Field of view (FOV): 157.2° (D) 96.8° (H) 115.6° (V)8. Maximum frame rate: 120FPS9. Signal-to-noise ratio (SNR): 40dB10. Baseline length: 80mm11. Synchronization: supports external trigger and synchronization12. Operating temperature: -20°C - 60°C13. Packaging list: RDK Stereo Camera Module GS130W main unit x 1; 22-pin cable about 100mm x 2Specification: Package Weight One Package Weight 0.13kgs / 0.30lb One Package Size 20cm * 6cm * 5cm / 7.87inch * 2.36inch * 1.97inch Qty per Carton 70 Carton Weight 11.00kgs / 24.25lb Carton Size 42cm * 37cm * 32cm / 16.54inch * 14.57inch * 12.6inch Loading Container 20GP: 536 cartons * 70 pcs = 37520 pcs 40HQ: 1244 cartons * 70 pcs = 87080 pcs

Read more less

1. RP2350B microcontroller chip designed for Raspberry Pi2. Unique dual-core, dual-architecture design featuring dual-core ARM Cortex-M33 processors and dual-core Hazard3 RISC-V processors, each clocked at up to 150MHz, enabling flexible switching between architectures3. Integrated 520KB SRAM, 16MB on-chip Flash, and 2MB PSRAM4. Features a Type-C interface for reversible plugging5. Onboard 7-inch capacitive LCD display with 800 × 480 resolution and 65K colors6. Supports I2C interface for capacitive touch control, 5-point touch, with interrupt support (touch version only)7. Onboard interfaces include Sensor, CAN, RS485, I2C, and UART8. USB 1.1 host and device support9. Supports low-power sleep and hibernation modes10. USB mass storage mode for drag-and-drop program downloads11. Precise on-chip clock and timers12. Built-in temperature sensor for real-time chip temperature monitoring13. 12 programmable I/O (PIO) state machines for custom peripheral supportPackage contents:- Display x 1- HY2.0 2-pin to male DuPont connector 2-pin about 10cm x 2- HY2.0 3-pin to male DuPont connector 3-pin about 10cm x 1- HY2.0 4-pin to male DuPont connector 4-pin about 10cm x 2- Screw set x 1Specification: Package Weight One Package Weight 0.21kgs / 0.47lb One Package Size 20cm * 14cm * 4cm / 7.87inch * 5.51inch * 1.57inch Qty per Carton 36 Carton Weight 9.00kgs / 19.84lb Carton Size 42cm * 38cm * 30cm / 16.54inch * 14.96inch * 11.81inch Loading Container 20GP: 556 cartons * 36 pcs = 20016 pcs 40HQ: 1292 cartons * 36 pcs = 46512 pcs

Read more less

1. Tempered glass panel screen with responsive touch, high-definition display, and durable design2. Capacitive 10-point touchscreen featuring sensitive touch, intuitive operation, and rapid response for efficient and convenient development3. Supports landscape and portrait display modes. Default setting is landscape; portrait mode can be enabled via software configuration4. Excellent heat dissipation with all-metal housing and efficient thermal design. Pre-drilled mounting holes on the back facilitate integration and embedding.5. Highly integrated with powerful performance, featuring an ESP32-P4-Core module design. Includes built-in ESP32-P4 and 32MB NOR Flash.6. Onboard ESP32-C6-MINI module extends ESP32-P4 with 2.4GHz Wi-Fi 6 and Bluetooth 5 (LE), communicating via SDIO protocol for stable connections and efficient data transfer7. Onboard ES8311 audio codec and ES7210 echo cancellation circuit, paired with dual microphones and speaker to meet daily audio application needs8. Supports AI voice interaction with mainstream AI platforms, enabling integration with online large model platforms, such as Doubao, DeepSeek, and other AI modelsScreen specifications1. Resolution: 7 inch: 120 x 1280; 8 inch/10.1 inch: 800 x 12802. Communication interface: MIPI 2-lane3. Brightness: 7 inch: 450 cd/square meter; 8 inch/10.1 inch: 400 cd/square meter4. Driver chip: 7 inch: ILI9881C; 8 inch/10.1 inch: JD93655. Touch chip: GT92716. Display size: 7 inch: 8.8 x 15.5cm; 8 inch: 10.824 x 172.82cm; 10.1 inch: 13.596 x 21.718 cm7. Contrast ratio: 7 inch: 800:1; 8 inch: 1200:1; 10.1 inch: 800:18. Viewing angle: 7 inch: 170°; 8 inch/10.1 inch: 178°9. Operating temperature: 0-60°C10. Pixel size: 7 inch: 0.12075 x 0.12075mm; 8 inch: 0.13455 x 0.13455mm; 10.1 inch: 0.1692 x 0.1692mmFront camera specifications1. Image sensor: OV56472. CMOS size: 1/4 inch3. Pixels: 5 megapixels4. Aperture: F2.45. Focal length: 3.89mm6. Diagonal field of view: 72.9°7. Distortion: less than 1.5%8. Depth of field: 20cm to infinity9. Image: static image resolution 2592 x 1944 pixels10. Video: 1920 x 1080p at 30fps, 1280 x 720p at 60fps, 640 x 480p at 60fps, 640 x 480p at 90fpsPackaging list:- Host x 1- RPI-HMI press plate x 4- Screw pack x 1- 2PIN battery terminal about 80mm x 1Specification: Package Weight One Package Weight 0.65kgs / 1.44lb One Package Size 30cm * 20cm * 5cm / 11.81inch * 7.87inch * 1.97inch Qty per Carton 14 Carton Weight 11.00kgs / 24.25lb Carton Size 42cm * 37cm * 32cm / 16.54inch * 14.57inch * 12.6inch Loading Container 20GP: 536 cartons * 14 pcs = 7504 pcs 40HQ: 1244 cartons * 14 pcs = 17416 pcs

Read more less

1. Tempered glass panel screen with responsive touch, high-definition display, and durable design2. Capacitive 10-point touchscreen featuring sensitive touch, intuitive operation, and rapid response for efficient and convenient development3. Supports landscape and portrait display modes. Default setting is landscape; portrait mode can be enabled via software configuration4. Excellent heat dissipation with all-metal housing and efficient thermal design. Pre-drilled mounting holes on the back facilitate integration and embedding.5. Highly integrated with powerful performance, featuring an ESP32-P4-Core module design. Includes built-in ESP32-P4 and 32MB NOR Flash.6. Onboard ESP32-C6-MINI module extends ESP32-P4 with 2.4GHz Wi-Fi 6 and Bluetooth 5 (LE), communicating via SDIO protocol for stable connections and efficient data transfer7. Onboard ES8311 audio codec and ES7210 echo cancellation circuit, paired with dual microphones and speaker to meet daily audio application needs8. Supports AI voice interaction with mainstream AI platforms, enabling integration with online large model platforms, such as Doubao, DeepSeek, and other AI modelsScreen specifications1. Resolution: 7 inch: 120 x 1280; 8 inch/10.1 inch: 800 x 12802. Communication interface: MIPI 2-lane3. Brightness: 7 inch: 450 cd/square meter; 8 inch/10.1 inch: 400 cd/square meter4. Driver chip: 7 inch: ILI9881C; 8 inch/10.1 inch: JD93655. Touch chip: GT92716. Display size: 7 inch: 8.8 x 15.5cm; 8 inch: 10.824 x 172.82cm; 10.1 inch: 13.596 x 21.718 cm7. Contrast ratio: 7 inch: 800:1; 8 inch: 1200:1; 10.1 inch: 800:18. Viewing angle: 7 inch: 170°; 8 inch/10.1 inch: 178°9. Operating temperature: 0-60°C10. Pixel size: 7 inch: 0.12075 x 0.12075mm; 8 inch: 0.13455 x 0.13455mm; 10.1 inch: 0.1692 x 0.1692mmFront camera specifications1. Image sensor: OV56472. CMOS size: 1/4 inch3. Pixels: 5 megapixels4. Aperture: F2.45. Focal length: 3.89mm6. Diagonal field of view: 72.9°7. Distortion: less than 1.5%8. Depth of field: 20cm to infinity9. Image: static image resolution 2592 x 1944 pixels10. Video: 1920 x 1080p at 30fps, 1280 x 720p at 60fps, 640 x 480p at 60fps, 640 x 480p at 90fpsPackaging list:- Host x 1- RPI-HMI press plate x 4- Screw pack x 1- 2PIN battery terminal about 80mm x 1Specification: Package Weight One Package Weight 0.55kgs / 1.22lb One Package Size 24cm * 18cm * 5cm / 9.45inch * 7.09inch * 1.97inch Qty per Carton 24 Carton Weight 15.00kgs / 33.07lb Carton Size 50cm * 38cm * 32cm / 19.69inch * 14.96inch * 12.6inch Loading Container 20GP: 438 cartons * 24 pcs = 10512 pcs 40HQ: 1018 cartons * 24 pcs = 24432 pcs

Read more less

1. Supports up to 10-point touch; actual touch points depend on the software system2. Tempered glass panel with 6H hardness3. Backlight brightness adjustable via software4. Full-laminated screen for high clarity and dust resistance5. IPS display panel delivers excellent performance with a wide 178° viewing angle6. This product defaults to portrait orientation with a resolution of 480 x 1920 (H x V). Landscape display can be enabled by modifying software settings7. Size: about 24.5 x 6.8cmPackage contents:- 8.8-DSI-TOUCH-A touchscreen x 1- MIPI-DSI-Cable-12cm x 1- MX1.25 2-pin to 2.54mm 3-pin adapter cable x 1- FFC cable 22-pin 200mm (opposite direction) x 2- MX1.25 2-pin to MX1.25 4-pin adapter about 150mm x 1- Screw set x 1Specification: Package Weight One Package Weight 0.30kgs / 0.67lb One Package Size 28cm * 12cm * 4cm / 11.02inch * 4.72inch * 1.57inch Qty per Carton 36 Carton Weight 12.00kgs / 26.46lb Carton Size 50cm * 38cm * 30cm / 19.69inch * 14.96inch * 11.81inch Loading Container 20GP: 467 cartons * 36 pcs = 16812 pcs 40HQ: 1086 cartons * 36 pcs = 39096 pcs

Read more less

1. Tempered glass panel screen with responsive touch, high-definition display, and durable design2. Capacitive 10-point touchscreen featuring sensitive touch, intuitive operation, and rapid response for efficient and convenient development3. Supports landscape and portrait display modes. Default setting is landscape; portrait mode can be enabled via software configuration4. Excellent heat dissipation with all-metal housing and efficient thermal design. Pre-drilled mounting holes on the back facilitate integration and embedding.5. Highly integrated with powerful performance, featuring an ESP32-P4-Core module design. Includes built-in ESP32-P4 and 32MB NOR Flash.6. Onboard ESP32-C6-MINI module extends ESP32-P4 with 2.4GHz Wi-Fi 6 and Bluetooth 5 (LE), communicating via SDIO protocol for stable connections and efficient data transfer7. Onboard ES8311 audio codec and ES7210 echo cancellation circuit, paired with dual microphones and speaker to meet daily audio application needs8. Supports AI voice interaction with mainstream AI platforms, enabling integration with online large model platforms, such as Doubao, DeepSeek, and other AI modelsScreen specifications1. Resolution: 7 inch: 120 x 1280; 8 inch/10.1 inch: 800 x 12802. Communication interface: MIPI 2-lane3. Brightness: 7 inch: 450 cd/square meter; 8 inch/10.1 inch: 400 cd/square meter4. Driver chip: 7 inch: ILI9881C; 8 inch/10.1 inch: JD93655. Touch chip: GT92716. Display size: 7 inch: 8.8 x 15.5cm; 8 inch: 10.824 x 172.82cm; 10.1 inch: 13.596 x 21.718 cm7. Contrast ratio: 7 inch: 800:1; 8 inch: 1200:1; 10.1 inch: 800:18. Viewing angle: 7 inch: 170°; 8 inch/10.1 inch: 178°9. Operating temperature: 0-60°C10. Pixel size: 7 inch: 0.12075 x 0.12075mm; 8 inch: 0.13455 x 0.13455mm; 10.1 inch: 0.1692 x 0.1692mmFront camera specifications1. Image sensor: OV56472. CMOS size: 1/4 inch3. Pixels: 5 megapixels4. Aperture: F2.45. Focal length: 3.89mm6. Diagonal field of view: 72.9°7. Distortion: less than 1.5%8. Depth of field: 20cm to infinity9. Image: static image resolution 2592 x 1944 pixels10. Video: 1920 x 1080p at 30fps, 1280 x 720p at 60fps, 640 x 480p at 60fps, 640 x 480p at 90fpsPackaging list:- Host x 1- RPI-HMI press plate x 4- Screw pack x 1- 2PIN battery terminal about 80mm x 1Specification: Package Weight One Package Weight 0.45kgs / 1.00lb One Package Size 24cm * 16cm * 5cm / 9.45inch * 6.3inch * 1.97inch Qty per Carton 28 Carton Weight 14.00kgs / 30.86lb Carton Size 50cm * 37cm * 34cm / 19.69inch * 14.57inch * 13.39inch Loading Container 20GP: 423 cartons * 28 pcs = 11844 pcs 40HQ: 984 cartons * 28 pcs = 27552 pcs

Read more less

1. RP2350B microcontroller chip designed for Raspberry Pi2. Unique dual-core, dual-architecture design featuring dual-core ARM Cortex-M33 processors and dual-core Hazard3 RISC-V processors, each clocked at up to 150MHz, enabling flexible switching between architectures3. Integrated 520KB SRAM, 16MB on-chip Flash, and 2MB PSRAM4. Features a Type-C interface for reversible plugging5. Onboard 7-inch capacitive LCD display with 800 × 480 resolution and 65K colors6. Supports I2C interface for capacitive touch control, 5-point touch, with interrupt support (touch version only)7. Onboard interfaces include Sensor, CAN, RS485, I2C, and UART8. USB 1.1 host and device support9. Supports low-power sleep and hibernation modes10. USB mass storage mode for drag-and-drop program downloads11. Precise on-chip clock and timers12. Built-in temperature sensor for real-time chip temperature monitoring13. 12 programmable I/O (PIO) state machines for custom peripheral supportPackage contents:- Display x 1- HY2.0 2-pin to male DuPont connector 2-pin about 10cm x 2- HY2.0 3-pin to male DuPont connector 3-pin about 10cm x 1- HY2.0 4-pin to male DuPont connector 4-pin about 10cm x 2- Screw set x 1Specification: Package Weight One Package Weight 0.29kgs / 0.65lb One Package Size 24cm * 15cm * 4cm / 9.45inch * 5.91inch * 1.57inch Qty per Carton 36 Carton Weight 12.00kgs / 26.46lb Carton Size 50cm * 38cm * 32cm / 19.69inch * 14.96inch * 12.6inch Loading Container 20GP: 438 cartons * 36 pcs = 15768 pcs 40HQ: 1018 cartons * 36 pcs = 36648 pcs

Read more less

1. Pixel count: 12 million2. Sensor chip: IMX5773. Interface type: USB2.0 Type-C / SH1.0 4PIN connector4. Sensor size: 1/2.3 inch5. Aperture (F): 2.86. Focal length (EFL): 2.88mm7. Field of view (FOV): 113°8. Distortion: less than -1.5%9. Focusing method: fixed focusing10. Supported formats: MJPG, YUY211. Static image resolution: 3840 x 302412. Video recording support: 20FPS 3840 x 3024; 30FPS 3840 x 2160; 30FPS 2592 x 1944; 30FPS 1920 x 108013. Operating voltage: 5V ± 5%14. Operating temperature: 0°C - 50°C15. Module size: about 3.4 x 3.4 cm16. Packaging list: IMX577 12MP USB Camera (A) x 1; Dust cover x 1; 4PIN dual-head cable x 1Specification: Package Weight One Package Weight 0.05kgs / 0.12lb One Package Size 6cm * 6cm * 5cm / 2.36inch * 2.36inch * 1.97inch Qty per Carton 280 Carton Weight 16.00kgs / 35.27lb Carton Size 50cm * 37cm * 32cm / 19.69inch * 14.57inch * 12.6inch Loading Container 20GP: 450 cartons * 280 pcs = 126000 pcs 40HQ: 1045 cartons * 280 pcs = 292600 pcs

Read more less

1. Pixel count: 2 million2. Sensor chip: OV27353. Interface type: USB2.0 Type-C / SH1.0 4-pin connector4. Sensor size: 1/2.7 inch5. Aperture (F): 2.76. Focal length (EFL): 2.88mm7. Field of view (FOV): 96°8. Distortion: less than -0.2%9. Focusing method: fixed focusing10. Supported formats: MJPG, YUY211. Static image resolution: 1920 x 108012. Video recording support: 30 FPS 1920 x 1080; 30 FPS 1280 x 72013. Operating voltage: 5V ± 5%14. Operating temperature: 0°C - 50°C15. Module size: about 2.5 x 2.5 cm16. Packaging list: OV2735 2MP USB Camera (A) x 1; 4-pin dual-jumper cable x 1Specification: Package Weight One Package Weight 0.03kgs / 0.07lb One Package Size 5cm * 5cm * 4cm / 1.97inch * 1.97inch * 1.57inch Qty per Carton 485 Carton Weight 16.00kgs / 35.27lb Carton Size 47cm * 38cm * 32cm / 18.5inch * 14.96inch * 12.6inch Loading Container 20GP: 466 cartons * 485 pcs = 226010 pcs 40HQ: 1083 cartons * 485 pcs = 525255 pcs

Read more less

1. Pixel count: 5 million2. Photographic sensor: OS05A103. Interface type: USB2.0 Type-C / SH1.0 4-pin connector4. Sensor size: 1/2.7 inches5. Aperture (F): 2.76. Focal length (EFL): 2.88mm7. Field of view (FOV): 96°8. Distortion: less than -0.2%9. Focusing method: fixed focusing10. Supported formats: MJPG, YUY211. Static image resolution: 2592 x 194412. Video recording support: 30 FPS 2592 x 1944; 30 FPS 1920 x 1080; 30 FPS 1280 x 72013. Operating voltage: 5V ± 5%14. Operating temperature: 0°C - 50°C15. Module size: about 2.5 x 2.5 cm16. Packaging list: OS05A10 5MP USB Camera (A) x 1; 4PIN dual-head cable x 1Specification: Package Weight One Package Weight 0.03kgs / 0.07lb One Package Size 5cm * 5cm * 4cm / 1.97inch * 1.97inch * 1.57inch Qty per Carton 485 Carton Weight 16.00kgs / 35.27lb Carton Size 47cm * 38cm * 32cm / 18.5inch * 14.96inch * 12.6inch Loading Container 20GP: 466 cartons * 485 pcs = 226010 pcs 40HQ: 1083 cartons * 485 pcs = 525255 pcs

Read more less

1. Features the RP2350A microcontroller chip designed by Raspberry Pi2. Unique dual-core, dual-architecture design, featuring dual-core ARM Cortex-M33 processors and dual-core Hazard3 RISC-V processors, both operating at up to 150MHz, allowing users to flexibly switch between the two architectures3. Built-in 520KB of SRAM and 16MB of on-chip Flash4. Features a Type-C interface, eliminating the need to worry about orientation when plugging in5. On-board 1.85-inch LCD screen with 360 x 360 resolution and 65K colors6. Supports capacitive touch control via I2C interface, with interrupt support7. On-board resources include UART, I2C interfaces, and an MX1.25 2-pin battery connector8. Supports USB 1.1 host and device modes9. Supports low-power sleep and hibernation modes10. Can be recognized as a mass storage device via USB for drag-and-drop program downloading11. Features 18 multi-purpose GPIO pins12. 2 SPI, 2 I2C, 2 UART, 4 12-bit ADCs, and 12 controllable PWM channels13. Precise on-chip clock and timers14. Built-in temperature sensor for real-time monitoring of chip temperature15. 12 programmable I/O (PIO) state machines for custom peripheral support16. Size: basic version about 5.8 x 1.7 cm; with speaker about 5.8 x 5.11 cmSpecification: Package Weight One Package Weight 0.03kgs / 0.07lb One Package Size 8cm * 8cm * 4cm / 3.15inch * 3.15inch * 1.57inch Qty per Carton 210 Carton Weight 7.30kgs / 16.09lb Carton Size 50cm * 38cm * 34cm / 19.69inch * 14.96inch * 13.39inch Loading Container 20GP: 412 cartons * 210 pcs = 86520 pcs 40HQ: 958 cartons * 210 pcs = 201180 pcs

Read more less