Electronics Modules

FeaturesThe Solar Power Manager (B) is compatible with general 6V~24V solar panels. It can recharge the 3.7V rechargeable Li-po battery through solar panel or USB TYPE-C connection, and provides 5V / 3A regulated output (with multi protocols support including PD/QC/FCP/PE/SFCP). The module features MPPT (Maximum Power Point Tracking) function and multi protection circuits, therefore, it is able to keep operating with high-efficiency, stability, and safety. It is suitable for solar powered, low-power IoT, and other environmental protection projects. 1. Support MPPT (Maximum Power Point Tracking) function, maximizing the efficiency of the solar panel 2. Flexible battery recharging: from solar panel or USB TYPE-C power adapter 3. Compatible with 6V~24V solar panels, DC-002 jack input or screw terminal input 4. Onboard MPPT SET switch, select the level closed to input level to improve recharging efficiency 5. Onboard aluminum electrolytic capacitor and SMD ceramic capacitor, reducing the ripple, stable performance 6. PH2.0 battery connector, with embedded 10000mAh 3.7V rechargeable Li-po battery 7. Several LED indicators, for monitoring the status of solar panel and battery 8. Multi protection circuits: over charge / over discharge / reverse-proof / over heat / over current, stable and safe to use

Read more less

Overview1. This is a Raspberry Pi LoRa HAT based on SX1262, covers 868MHz frequency band frequency band. It allows data transmission up to 5km through serial port.2. By utilizing the new generation LoRa spread spectrum modulation technology, the communication distance of the module is as long as 5km, also supports auto repeating to transmit longer. Other features include Wake on Radio, wireless config, carrier sensing, communication key, and so on.3. Comparing with normal LoRa modules, the SX1262 LoRa HAT achieves longer communication distance, higher rate, lower consumption, better safety and anti-interference. It is suitable for various applications such as industrial control, smart home, data collection, etc.Features1.Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards2. Onboard CP2102 USB TO UART converter, for serial debugging3. Bring the UART control interface, for connecting host boards like Arduino/STM324. 4x LED indicators, easy to check the module status5. LoRa spread spectrum modulation technology, up to 81 available signal channel, longer communication distance, more robust to interference6. Auto multi-level repeating, suit for ultra long range communication, allows multi network on the same region7. Low power consumption features like deep sleeping and Wake on Radio, ideal for battery-powered applications8. Customizable communication key which won't be retrieved, greatly improves the security of user data9. Support LBT, monitoring the signal channel noise before transmitting, greatly improves the success ratio under extreme environment10. Support RSSI signal intensity indicating, for evaluating signal quality, tuning the network11. Support wireless parameter configuration, by sending wireless command/data packet, remotely configure or retrieve the module parameter12. Support fixed-point transmission, broadcast, signal channel monitor13. Come with development resources and manual (examples for Raspberry Pi/STM32)What is on Board1. SX1262 LoRa module2. 74HC125V: voltage level translator3. CP2102: USB TO UART converter4. Raspberry Pi GPIO connector: for connecting with Raspberry Pi5. USB TO UART port6. UART header: for connecting host boards like STM32/Arduino7. SMA antenna connector8. IPEX antenna connector9. Indicators:- RXD/TXD: UART RX/TX indicator- AUX: auxiliary indicator- PWR: power indicator10. UART selection jumpers- A: Control the LoRa module through USB TO UART- B: Control the LoRa module through Raspberry Pi- C: Access Raspberry Pi through USB TO UART11. LoRa mode selection jumpers- Short M0, short M1: Transmission mode- Short M0, open M1: Configuration mode- Open M0, short M1: WOR mode- Open M0, open M1: deep sleep modeSpecification1. RF module: SX12622. Frequency band: 850.125 ~ 930.125MHz3. Radio rate: 0.3kbps ~ 62.5kbps (programmable)4. Transmit power: 22.0dBm (10/13/17/22dBm programmable)5. Receive sensitivity: -147dBm (radio rate 2.4kbps)6. Power consumption: - Transmit current: 133mA (transient consumption)- Receive current: 11mA- Sleep current: 2uA (LoRa module software shutoff)7. Communication interface: UART (TTL level)8. Baudrate: 1200bps ~ 115200bps (9600bps by default)9. Packet length: 240 Byte (32/64/128/240 Byte programmable)10. Cache: 1000 Byte11. Experimental range: 5km (condition: cloudless and wild, altitude 2.5m, antenna gain 5dBi, radio rate 2.4kbps)12. Power supply: 5V13. Logic level: 3.3V/5V14. Operating temperature: -40~85 degree C15. Applications: Smart home, industrial sensors, building automation, smart meters, and more other IoT applications16. Dimensions: 7cm x 12cm x 2cm17. Weight: 69g18. Packing List:- SX1262 868MHz LoRa HAT x1- USB type A plug to micro plug cable x1- 868MHz antenna x1

Read more less

1. This USB 3.2 Gen1 to Gigabit Ethernet wired Internet module incorporates Realtek original high performance controller RTL8153, with features including multi systems compatibility, driver-free, plug-and-play, supports systems like Win7/8/8.1/10, Mac, Linux, Android, and so on. 2. Easily providing wired Gigabit Ethernet connection for devices which has no Ethernet port or broken NIC, fast data rate, low latency, stable performance, smooth experience for gaming or HD movies. Specifications: 1. Controller: RTL8153 2. ETH port: RJ45 Gigabit Ethernet 3. USB: USB 3.2 Gen1 (data rate will be downgraded while connecting with a USB 2.0 port) 4. Network standard: 10/100/1000Mbps 5. System support: Win7/8/8.1/10, Mac, Linux, Android 6. Cable length: About 15cm (measured manually, for reference ONLY) 7. Status indicator: The green light keeps on, the yellow light keeps blinking Package list: 1. USB 3.2 Gen1 TO Gigabit ETH x 1 2. USB Type-A extension cable x 1

Read more less

About The ProductOverview 1. This is an industrial USB to RS485 converter with original FT232RL and SP485EEN inside. It features embedded protection circuits such as lightningproof, resettable fuse, ESD protection, and TVS diode, etc. It is pretty small in size. 2. The USB TO RS485 is very easy to use, allows automatic transceiving. Due to its fast communication, stability, reliability, and safety, it is an ideal choice for industrial control equipments and/or applications with high communication requirement. Features 1. USB to RS485 communication 2. Adopt original FT232RL and SP485EEN, fast communicating, stable and reliable, better compatibility 3. Onboard TVS (Transient Voltage Suppressor), effectively suppress surge voltage and transient spike voltage in the circuit, lightningproof & anti-electrostatic 4. Onboard self-recovery fuse and protection diodes, ensures the current/voltage stable outputs, provides over-current/over-voltage proof, improves shock resistance 5. 3 LEDs for indicating the power and transceiver status Specifications 1. Product type: Industrial converter 2. Baudrate: 300-921600bps 3. Host port: USB 4. Device port: RS485 5. USB: - Operating voltage: 5V - Connector: USB-A - Protection: 200mA self-recovery fuse, ESD protection - Transmission distance: about 5m 6. RS485: - Connector: screw terminal - Pins: A+, B-, GND - Direction control: hardware automatic control - Protection: 600W lightningproof and surge-suppress, 15KV ESD protection (onboard 120R balancing resistor) - Transmission distance: about 1200m (low rate) - Transmission mode: point-to-multipoints (up to 32 nodes, it is recommended to use repeaters for 16 nodes or more) 7. LED indicators: - PWR: red power indicator, light up when there is USB connection and voltage is detected - TXD: red TX indicator, light up when the USB port sends data - RXD: red RX indicator, light up when the device ports send data back 8. Operating environment: - Temperature: -15 ~ 70 degree - Humidity: 5%RH ~ 95%RH 9. Operating system: Mac, Linux, Android, WinCE, Windows 10 / 8.1 / 8 / 7 / XPPackage List1. USB TO RS485 x 1 2. USB-A male to female cable x 1 3. Screwdriver x 1

Read more less

Features1. This is a RS485 device data acquisitor / IoT gateway designed for industrial environment. 2. It combines multi functions in one, including serial server, Modbus gateway, MQTT gateway, RS485 to JSON, etc. 3. The module features RS485 and Ethernet ports, uses screw terminals for power input, supports 9~24V wide range power supply. 4. Rail-mount flame-retardant case design, small in size, easy to install. 5. It is suitable for applications like data acquisition, IoT gateway, safety & security IoT, and intelligent instrument monitoring...Specifications1. Communication interface: RS485, screw terminal, supports 32x slave devices 2. Power supply: 9 ~ 24V DC, screw terminal 3. Dimensions (L x W x H): 87 x 36 x 59 mm 4. Ethernet: 10 / 100M auto-negotiation RJ45 connector, 2 KV surge protection 5. Serial port: RS485 ?? 1: RXD, TXD, GND 6. Baudrate: 300 ~ 115200 bps 7. Parity bit: None, odd, even, mark, space 8. Data bit: 5 ~ 9 bits 9. Flow control: N/A 10. Protocol: ETHERNET, IP, TCP, UDP, HTTP, ARP, ICMP, DHCP, DNS 11. Configuration: Host, web browser, device management functions library 12. Communication method: TCP/IP direct communication, VCOM 13. Operating mode: TCP server, TCP client (coexisting with TCP server), UDP, UDP multicast 14. Operating temperature: -40 degree C ~ 85 degree C 15. Storage temperature: -45 degree C ~ 165degree C 16. Humidity range: 5% ~ 95% relative humidity

Read more less

1. Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards2. 1-Ch CAN, adopts MCP2515 controller and CAN transceiver, converts SPI to CAN3. 2-Ch RS485, adopts SC16IS752+SP3485 dual-chip combination, converts SPI to RS4854. Onboard power conversion circuit, supports 8~28V wide voltage power supply, can power the Raspberry Pi at the same time5. Onboard unibody power supply isolation, providing stable isolated voltage, no extra power supply required for the isolated terminal6. Onboard unibody digital isolation, for isolating the signal, reliable and jamproof, low power consumption7. Onboard TVS (Transient Voltage Suppressor), effectively suppress surge voltage and transient spike voltage in the circuit, lightningproof & anti-electrostatic8. Onboard resettable fuse and protection diodes, ensures the current/voltage stable outputs, provides over-current/over-voltage proof, improves shock resistance9. Onboard 120Ω terminal resistor, configured by jumper10. Onboard terminals and pin headers, more convenient connection11. Breakout SPI control pins, for connecting with host control boards

Read more less

1. Module support: for Jetson Orin NX / Jetson Orin Nano2. Power supply: DC 5V input3. Structure: embedded fan, aluminum alloy shell4. Electrical parameters: 0.65W (5V/0.13A)5. Cable length: 37+/-3mm6. Fan: PWM speed control, 5500+/-10%RPM7. Speed adjustable fan, elastic bracket and height limit screw

Read more less

Features:1. RS232/485 device data collector/IoT gateway specially designed for industrial environments.2. Integrate multiple functions into one, including serial port server, Modbus gateway, MQTT gateway, serial port to HTTPD client, etc.3. The module has RS232, RS485, WIFI, and Ethernet interfaces, which can realize serial to WIFI, serial to WIFI and other functions; Ethernet, Ethernet to WIFI, etc.4. Multiple onboard power interfaces support a wide range of 6~36V power supply, and can be equipped with PoE function.5. Industrial-grade metal shell design supports wall-mounted and rail-mounted installation. It is small in size and easy to install.6. Suitable for data collection, IoT gateway, security IoT, smart instrument monitoring and other applications.Product parameters:1. Frequency band: 2.412-2.484 GHz2. Wireless network: Station / AP / AP+Station mode3. Security mechanism: WPA-PSK / WPA2-PSK4. Encryption type: TKIP/AES5. Transmission power:802.11b: +19dBm (max @11Mbps)802.11g: +18dBm (max @54Mbps)802.11n: +17dBm (maximum @HT20, MCS7); +17dBm (maximum @HT40, MCS7)6. Receiving sensitivity:802.11b: -89dBm (@11Mbps)802.11g: -81dBm (@54Mbps)802.11n: -73dBm (@HT20, MCS7); -71dBm (@HT40, MCS7)7. Baud rate: 300-460800 bps8. Check digit: none, odd, even, mark, space9. Data bits: 5-9 bits10. Flow control: RTS/CTS N/A11. Protocol: TCP/UDP/ARP/ICMP/DHCP/DNS/HTTP/MQTT12. Configuration: host, browser, serial AT command13. Communication method: TCP/IP direct communication, VCOM14. Working mode: transparent transmission, serial port command, HTTPD Client, Modbus TCP to Modbus RTU15. Working temperature: minus 40 degrees Celsius - 85 degrees Celsius16. Humidity range: 5%-95% relative humidity17. Product size: 85 x 84 x 24mm18. Weight: 157g, 169gPacking list:RJ45 network port:-RS232/485 to WIFI Ethernet (B) x1-2.4G WiFi antenna x1-Rail mounting buckle x1-Screwdriver x1-Screw pack x1RJ45 network port supporting POE:-RS232/485 to WIFI POE ETH (B) x1-2.4G WiFi antenna x1-Rail mounting buckle x1-Screwdriver x1-Screw pack x1

Read more less

1. Using heavy gold PCB, machine welding process to ensure quality2. Chip built-in 16bit AD converter, 16-bit data output3. Communication method: standard IIC/SPI communication protocol4. Power supply: 3-5v5. Use chip: MPU-92506. Pin spacing: 2.54mm7. Size: 15x25mm

Read more less

OverviewThe RPi Relay Board gives your Pi the ability to control high voltage/high current devices, easily makes normal home appliances become intelligent.RPi Relay Board Features1. Supports Raspberry Pi A+/B+/2B/3B/3B+2. High quality relays, loads up to 5A 250V AC or 5A 30V DC3. Photo coupling isolation, prevent interference from high voltage circuit4. Onboard LEDs for indicating relays status5. Relay control jumper, allows to control the relays by custom pins other than the default pins6. Comes with development resources, including examples in wiringPi, WebioPi, shell, python, and bcm2835What is on the RPi Relay Board1. Raspberry Pi GPIO interface: for connecting Raspberry Pi2. Relay screw terminal: for connecting target devices3. Relays4. Photocoupler: PC8175. Relay indicator- LED on: relay NC is opened, NO is closed- LED off: relay NC is closed, NO is opened6. Power indicator7. Relay control jumper- Short the jumper: control the relays by default I/Os used in the example code- Open the jumper: control the relays by custom I/Os through jumper wiresPackage include- RPi Relay Board x 1- RPi screws pack (2pcs) x 1

Read more less

1. The portable instrument is automatically powered off after conversion and greatly reduces current consumption during idle periods2. Features: easy to implement, high precision, low current consumption, multi-mode conversion3. Power supply voltage: 2-5.5v4. Working temperature: -40 to 125 degrees celsius5. Programmable data rate: Transmission via I2C compatible serial interface6. Single mode: Automatic shutdown with onboard reference and oscillator7. Size: about 16 x 28mm8. Weight: about 2.5g

Read more less

1. Interface: TTL level RS232 format2. Purpose: experiment3. Card reading distance: below 5CM4. Application: smart home5. Weight: about 10g6. Coil inductance: 47~68uH7. Frequency: 125KHz8. Working voltage: DC 5V9. Working current: less than 50 mA10. Working temperature: -10 to 70 degrees Celsius11. Storage temperature: -20 to 80 degrees Celsius12. Coil size: 46x32x3mm13. Module size: 38.5x19x9mm

Read more less

OverviewSmart robot is always the favorite project of electronic enthusiasts, however, a robot will be "not that smart" if it is not AI-based.Welcome the JetBot, an actual smart robot powered by Jetson Nano. With the intelligent eye (front camera), facial recognition, object tracking, auto line following, and collision avoidance can be easily achieved. It also comes with ROS nodes code, which makes it easy to get started with the open source ROS (Robot Operating System), and to learn the system framework and concepts of ROS.Features1. Adopts 3x 18650 batteries (NOT included), high battery capacity, up to 12.6V voltage output, more powerful driving force.2. Integrates S-8254AA + AO4407A lithium battery protection circuit, provides protections for over-charge, over-discharge, over-current, and short circuit.3. Onboard APW7313 voltage regulator, provides stable 5V voltage for the Jetson Nano.4. Onboard TB6612FNG dual H-bridge motor driver.5. Onboard 0.91inch 128×32 pixels OLED, allows to display robot IP address, RAM, battery life, etc.6. Onboard ADS1115 AD acquisition chip for monitoring the battery in real time.7. Weight: 1029gWhat is on the JetBot Expansion Board1. S-8254AA: Lithium battery protector, provides protections for over-charge, over-discharge, over-current, and short circuit2. ADS1115: 16-bit AD acquisition chip, monitoring the battery in real time3. AO4407A: P-Channel MOSFET for protection circuit4. APW7313: 5V power regulator for powering the Jetson Nano5. PCA9685: PWM controller, I2C interface, for IO expansion6. TB6612FNG: dual H-bridge motor driver7. 0.91 inch OLED: SSD1306 driver chip, 128×32 pixels8. Battery charger input: charging the 3x 18650 batteries9. Power switch10. 18650 battery holder11. Motor connector (bottom side)12. Jetson Nano communication header: I2C interface and power supplyPacking List1. Jetson Nano Developer Kit x12. Micro SD Card 64GB ×13. Metal box x14. Camera holder x15.Acrylic piece x16. Jetbot expansion board x17. IMX219-160 Camera x18. Wireless-AC8265 x19. Motor 2PCS x110. Wheel 2PCS x111.Omni-direction wheel 2PCS x112. Power adapter EU head x113. 12.6V battery charger x114. Wireless gamepad x115. Screwdriver 2PCS x116. 6Pin 9cm cable x117. Screws pack x118. Spanner x119. Cooling fan x120. Micro SD card reader x1

Read more less

1. Raspberry Pi Camera, supports all revisions of the Pi2. 5 megapixel OV5647 sensor3. Adjustable focus distance4. Camera specifications- CCD size: 1/4inch- Aperture (F): 2.0- Focal Length: 6mm- Angle of View (diagonal): 60.6 degree- Sensor best resolution: 1080p5. Dimension: 32mm x 32mm

Read more less

1. Input voltage: DC4~12V2. Output voltage: DC2.5~8V3. Output power: 5W (do not use it with overload)4. Function description: suitable for common 5.0V USB fans on the market5. How to use: Plug the male head of the governor into a mobile phone charger, power bank, computer USB, etc., and then insert the fan plug into the female head of the governor to use6. Adjustment method: knob adjustment (clockwise increase, counterclockwise decrease)7. Features: strong wind and weak wind can be adjusted at will, fan stepless speed regulation, wide voltage input compatible with multi-speed power supply.8. The module is a speed-regulating fan module designed according to the principle of high-frequency switching power supply. The essence is to control the speed of the fan by adjusting the output voltage.9. Matters needing attention: When used to adjust the fan in two gears, please set the fan to the first gear, otherwise the speed may not be adjusted.10. Size: 50x18mm

Read more less

1. Using PT2399 reverberation chip, with NE5532 op amp, it can mix human voice and music, which can realize independent adjustment of music volume, microphone volume and reverberation time to achieve K song effect2. It can be used for DC 12-24V power supply or AC 5-12V, which can be directly used for various digital power amplifier boards. If the power supply voltage is the same, the power supply can be shared3. Input voltage: DC12-24V4. Reverberation chip: PT239995. Microphone input: 26. Knob spacing: 24MM Microphone spacing: 17.6MM7. Output channel: 2 channels8. Frequency response range: 25HZ-17KHZ9. Appearance size: 117 x 53MM10. Weight: 75 grams11. Note: Only adjustable loop microphones can be used, other microphones such as condenser microphones, pole microphones, and headphone microphones are not available.

Read more less

1. Three-in-one electronic clock module, integrating three practical functions: time, thermometer and voltmeter2. Using RX8025T clock chip, the timing accuracy is stable3. The lengthened temperature probe can effectively solve the problem that the temperature affected by the module temperature is not accurate enough4. Power supply voltage: DC5.0-30V5. Temperature function range: -40-120 degrees Celsius, resolution 0.16. Voltmeter function range: DC5-30V (requires pure DC power supply, it is not recommended to use 24V battery, because the voltage may be too high during charging and burn)7. Size: about 4x1.4x1.3cmFunction and usage instructions:1. Adjust time, date, year, voltage error, temperature error cycle display item definition, alternate display interval time2. In the non-setting state, press the left key to enter the time adjustment (note that the colon in the middle is bright):- At this time, the minute bar starts to flash, press the right button to increase, the adjustment range is 00-59, after adjusting, press the left button again, the hour bar starts to flash, press the right button to increase, the adjustment range is 00-23- After adjusting the hour, press the left button again to enter the date adjustment (note that the colon in the middle is off), at this time the date column starts to flash, press the right button to increase, the adjustment range is 1-31, after the date is adjusted, press the left button again key, the month column starts to flash, press the right key to increase, the adjustment range is 1-12, after adjusting the date, press the left key again, the year column starts to flash, press the right key to increase, the adjustment range is 2012-2049- After adjusting the year, press the left key again to enter the error calibration function of the displayed voltage, the unit is 0.1V, a positive number means increase, and a negative number means decrease- Then press the left key again to enter the temperature error calibration setting, press the right key to increase, a positive number means increase, a negative number means decrease, the unit is Celsius- Press the left button again to enter the definition function dd option of the display item in the cycle display state,Press the right button to change the value: (dd:0) time + temperature + voltage, (dd: 1) time + temperature, (dd: 3) time + voltage- Press the left button again to enter the cycle display alternate interval time dF option, press the right button to change the value, the larger the value, the longer the interval- Press the left button again to save all the set values ​​and return to the normal display state3. Switch display items: in the non-setting state, press the right key to switch the display items, and the display will switch between the time-date-temperature-voltage alternate display

Read more less

1. Base board for Compute Module 4 Lite / eMMC 2. Standard CM4 socket, with multiple peripheral interfaces, suitable for narrow application environment Specifications: 1. CM4 socket: Suitable for all variants of Compute Module 4 2. Connector: Raspberry Pi 40PIN GPIO interface x 1 3. USB: USB 2.0 Type A interface x 1 4. Camera: MIPI CSI-2 port x 1 (15pin 1.0mm FPC connector) 5. Storage: Micro SD card socket for Compute Module 4 Lite (without eMMC) variants 6. Power: 5V 7. Size: 55 x 40mm Package list 1. CM4-NANO-A x1 2. 2 x 20PIN color-coded straight pinheader x 2

Read more less

Features:1. WAVE ROVER is a four-wheel-drive mobile robot chassis with an all-metal body. It has strong off-road traversing capabilities and shock absorption performance. All codes are open source and can be developed again.2. Supports multiple hosts (Raspberry Pi, Jetson Nano, Jetson Orin Nano, etc.). The host can communicate with the ESP32 slave through the serial port.3. Equipped with four N20 reduction motors and high-quality gearboxes, the mobile robot can travel at high speeds and has strong power.4. Built-in 3S UPS power module, supports 3 18650 lithium batteries (series connection, not included), provides uninterrupted power supply for the robot, and supports charging and power output at the same time.5. Built-in multi-functional robot driver board, based on ESP32, with onboard WIFI and Bluetooth, used to drive serial bus servos, output PWM signals, expand TF card slots, etc.6. WAVE ROVER uses flexible rubber tires, which greatly reduces the impact of complex terrain and easily meets the needs of high-speed driving, shock absorption, and off-roading.7. Comes with a mounting plate that can be used to install hosts (Raspberry Pi 4B, Jetson Nano, Jetson Orin Nano, etc.), LD19/STL-27L lidar, and gimbal cameras, providing more possibilities for secondary development.Product parameters:1. Tire material: nylon wheels, rubber tires2. Body material: 5052 aluminum alloy (2mm thick)3. OLED screen: 0.91 inches4. Chassis height: 33.70mm5. Tire diameter: 80mm6. Tire width: 42.50mm7. Motor: N20 12V 200RPM x 48. Number of driving wheels: 49. Running speed: 1.25m/s10. Vertical obstacle surmounting ability: 40mm11. Drive payload: 0.8kg12. Climbing ability: 22 degrees13. Minimum turning radius: 0m (rotating in place)14. Motor power: 1.5W x 415. Remote control function: WIFI AP/STA16. Upper surface area: 17551 square millimeters17. Communication interface: UART/serial bus servo interface/I2C18. Battery support: 18650 lithium battery × 3 (delivered without battery)19. Overall dimensions: 194×168×100mm20. Weight: 860g

Read more less

1. Design with good heat dissipation, do not have to install the cooling fan or heatsink. 2. This case is constructed out of high quality aluminum material. 3. Suitable for Raspberry Pi 4 only 4. Access to all ports of Raspberry Pi 4 5. Cable interface is reserved, support to install cable. Note: Please insert the Micro SD card to Raspberry Pi before installing the case.

Read more less

1. Dual decoding supports music in MP3/WMA/WAV/FLAC/APE lossless decoding format2. Support bluetooth call function, power off memory function3. Support MMC/SD/MMA and other cards, support USB interface (U disk)4. Support external audio source input LINE IN5. Support radio FM, search frequency band (87.5MHZ-108.0MHZ)6. Mobile phone Bluetooth connection matching fast, low-power decoding scheme7. Application areas: speakers, tricycles, vans, buses, trolley speakers, power amplifiers, etc.8. Bluetooth transmission distance: within 20 meters9. Radio channel: 87.5Mhz-108Mhz10. Voltage input: DC 5V11. Amplifier: 2 x 3W12. Function: Bluetooth 5.0+lossless decoding+call+radio FM+AUX+USB+TF card13. Speaker: 4 ohms, 3W14. Buttons: three-button control, VOL-/AUTO/VOL+15. Dimensions: 71 x 22mm

Read more less

1. Based on Qualcomm platform, support 5G NSA and SA networking, support multi-mode & multi-band2. Multi-constellation dual-band positioning: GPS, Beidou, Glonass, Galileo, and QZSS3. Operating system support: Windows/Linux/Android4. USB 3.1 port (USB 2.0 compatible) for connecting to PC, Raspberry Pi, or Jetson Nano host board to enable high speed 5G communication5. Standard M.2 B KEY slot, compatible with different 5G modules: SIM8202X-M2 / SIM8200EA-M2 / SIM8262X-M2 series6. Onboard UART, PWR, and RST control pin, built-in voltage level translator, enabled via DIP switch, for use with hosts like Raspberry Pi or Arduino7. Onboard USB-C connector, enabled via switch, for connecting standalone power supply for the module, allows more loads, stable amd flexible power supply8. Onboard power supply on/off switch, reset button and LED indicator, easy to turn on/off the module or monitor the operating status9. 4x SMA to IPEX antenna connectors, with pre-soldered SMA terminals for connecting antennas10. 2x SIM card slot, dual card single standby, switchable via AT command11. Onboard audio jack and audio decoder, allows audio operation like making phone call12. High efficiency power supply circuit, up to 3A output current

Read more less

1. This connector is a right-angle connector, which is designed to sit flush with the panel of the female port.2. It can be used to build entire custom cables for TV, Computer screens, etc.3. It can either be used as a replacement part or modification for an existing cable4. Interface: Vertical Mini HDMI plug5. Usage: For DIY HDMI cable6. Dimension: 12 x 16 x 17.5mm

Read more less

1. VCC: 3.3V - 5V power input2. GND: ground wire3. SCL: I2C clock pin4. SDA: I2C data pin5. Communication interface: I2C6. LCD controller: AiP310687. Working voltage: 3.3-5V8. Working temperature: minus 20-70 degrees Celsius9. Display panel: Character LCD10. Display size: 64.5 x 16.0mm11. Characters: 16 x 212. Product size: 87.0 x 32.0 x 13.0mm13. Built-in character LCD panel LCD160214. I2C control interface, only need two signal pins, saving IO resources15. Compatible with 3.3V/5V working voltage16. Comes with online development resources and manuals (Raspberry Pi/Jetson Nano/ESP32/Arduino examples)

Read more less

1. RP2040 microcontroller chip designed by Raspberry Pi in the United Kingdom2. Dual-core Arm Cortex M0+ processor, flexible clock running up to 133 MHz3. 264KB of SRAM, and 2MB of on-board Flash memory4. Onboard 5 × 5 RGB LED matrix for colorful lighting display5. Castellated module allows soldering direct to carrier boards6. USB 1.1 with device and host support7. Low-power sleep and dormant modes8. Drag-and-drop programming using mass storage over USB9. 20 × multi-function GPIO pins10. 2 × SPI, 2 × I2C, 2 × UART, 4 × 12-bit ADC, 16 × controllable PWM channels11. Accurate clock and timer on-chip12. Temperature sensor13. Accelerated floating-point libraries on-chip14. 8 × Programmable I/O (PIO) state machines for custom peripheral support

Read more less

Features:1. Supports connecting to host or MCU to control serial bus servo2. Allows simultaneous control of up to 253 ST/SC series serial bus servos (requires sufficient power supply)3. 9-12.6V voltage input (input voltage and servo voltage must match)4. Provide convenient serial bus servo control solutions5. Integrated control circuit to ensure stable operation of serial bus servo6. Compact size, saving space, suitable for integration into various projects with limited spaceProduct parameters:1. Power supply: DC 9-12.6V (ST series servo)2. Power connector: 5.5 × 2.1mm DC3. Communication interface: UART4. Mounting hole size: 2.5mm5. Mounting hole distance: 37 × 28mm6. Product size: 42 x 33mm7. Weight: 16 grams

Read more less

Features:1. RS232/485 device data collector/IoT gateway specially designed for industrial environments.2. Integrate multiple functions into one, including serial port server, Modbus gateway, MQTT gateway, serial port to HTTPD client, etc.3. The module has RS232, RS485, WIFI, and Ethernet interfaces, which can realize serial to WIFI, serial to WIFI and other functions; Ethernet, Ethernet to WIFI, etc.4. Multiple onboard power interfaces support a wide range of 6~36V power supply, and can be equipped with PoE function.5. Industrial-grade metal shell design supports wall-mounted and rail-mounted installation. It is small in size and easy to install.6. Suitable for data collection, IoT gateway, security IoT, smart instrument monitoring and other applications.Product parameters:1. Frequency band: 2.412-2.484 GHz2. Wireless network: Station / AP / AP+Station mode3. Security mechanism: WPA-PSK / WPA2-PSK4. Encryption type: TKIP/AES5. Transmission power:802.11b: +19dBm (max @11Mbps)802.11g: +18dBm (max @54Mbps)802.11n: +17dBm (maximum @HT20, MCS7); +17dBm (maximum @HT40, MCS7)6. Receiving sensitivity:802.11b: -89dBm (@11Mbps)802.11g: -81dBm (@54Mbps)802.11n: -73dBm (@HT20, MCS7); -71dBm (@HT40, MCS7)7. Baud rate: 300-460800 bps8. Check digit: none, odd, even, mark, space9. Data bits: 5-9 bits10. Flow control: RTS/CTS N/A11. Protocol: TCP/UDP/ARP/ICMP/DHCP/DNS/HTTP/MQTT12. Configuration: host, browser, serial AT command13. Communication method: TCP/IP direct communication, VCOM14. Working mode: transparent transmission, serial port command, HTTPD Client, Modbus TCP to Modbus RTU15. Working temperature: minus 40 degrees Celsius - 85 degrees Celsius16. Humidity range: 5%-95% relative humidity17. Product size: 85 x 84 x 24mm18. Weight: 157g, 169gPacking list:RJ45 network port:-RS232/485 to WIFI Ethernet (B) x1-2.4G WiFi antenna x1-Rail mounting buckle x1-Screwdriver x1-Screw pack x1RJ45 network port supporting POE:-RS232/485 to WIFI POE ETH (B) x1-2.4G WiFi antenna x1-Rail mounting buckle x1-Screwdriver x1-Screw pack x1

Read more less

Features:1. WAVE ROVER is a four-wheel-drive mobile robot chassis with an all-metal body. It has strong off-road traversing capabilities and shock absorption performance. All codes are open source and can be developed again.2. Supports multiple hosts (Raspberry Pi, Jetson Nano, Jetson Orin Nano, etc.). The host can communicate with the ESP32 slave through the serial port.3. Equipped with four N20 reduction motors and high-quality gearboxes, the mobile robot can travel at high speeds and has strong power.4. Built-in 3S UPS power module, supports 3 18650 lithium batteries (series connection, not included), provides uninterrupted power supply for the robot, and supports charging and power output at the same time.5. Built-in multi-functional robot driver board, based on ESP32, with onboard WIFI and Bluetooth, used to drive serial bus servos, output PWM signals, expand TF card slots, etc.6. WAVE ROVER uses flexible rubber tires, which greatly reduces the impact of complex terrain and easily meets the needs of high-speed driving, shock absorption, and off-roading.7. Comes with a mounting plate that can be used to install hosts (Raspberry Pi 4B, Jetson Nano, Jetson Orin Nano, etc.), LD19/STL-27L lidar, and gimbal cameras, providing more possibilities for secondary development.Product parameters:1. Tire material: nylon wheels, rubber tires2. Body material: 5052 aluminum alloy (2mm thick)3. OLED screen: 0.91 inches4. Chassis height: 33.70mm5. Tire diameter: 80mm6. Tire width: 42.50mm7. Motor: N20 12V 200RPM x 48. Number of driving wheels: 49. Running speed: 1.25m/s10. Vertical obstacle surmounting ability: 40mm11. Drive payload: 0.8kg12. Climbing ability: 22 degrees13. Minimum turning radius: 0m (rotating in place)14. Motor power: 1.5W x 415. Remote control function: WIFI AP/STA16. Upper surface area: 17551 square millimeters17. Communication interface: UART/serial bus servo interface/I2C18. Battery support: 18650 lithium battery × 3 (delivered without battery)19. Overall dimensions: 194×168×100mm20. Weight: 860g

Read more less

1. The input terminal has a MICRO USB female socket, you can directly use the mobile phone charger as an input to charge the lithium battery, and there are still input voltage wiring solder joints, which can be very convenient for DIY2. Power supply voltage: 5v3. Power supply current: 1A4. Purpose: Electric toys5. Charging cut-off voltage: 4.2v6. Large charging current: 1000mA7. Battery over-discharge protection voltage: 2.5v8. Battery overcurrent protection current: 3A9. Board size: 2.6x1.7cm10. Note: The load on the OUT terminal should be disconnected when charging, and the positive and negative poles should not be connected wrongly. Please use it according to the specifications, otherwise it will be directly damaged.

Read more less

1. Material: Aluminum alloy shell2. Power supply voltage: DC12-28V3. Power: 100W4. Input: DC+TYPE-C dual port input5. Support fast charge protocol: PD2.0 PD3.0 PPS, For Qualcomm QC4+/QC3.0, For Huawei SCP/FCP, For OPPO VOOC, For OnePlus DASH, For iOS 2.4A, For Samsung AFC, For VIVO 9V 2A dual engine, For MediaTek PE2.06. Features:Exquisite and small, the digital tube displays the current and voltage, can switch the display content intelligently, and has strong compatibility. After the fast charge protocol is activated, the digital tube will display the output fast charge protocol type.7. Weight: About 60 grams8. Size: About 5.3x4.6x2.1 cmInstructions for use:1. Withstand voltage within 32V, it is recommended to use within 28V. This module is a pure step-down module and has no boost function. If you want to use 20V output, you must use a DC power supply above 21V; low voltage can reach 6V, but 6V is mostly fast the charge will not be activated, and the output power of 100W can only be reached when the PD is output (PD20V, 5A)2. For low-voltage and high-current fast charging, please use the original data cable. If you want to measure the charging voltage and current, you must use a low-resistance USB meter, otherwise the charging current will be affected.3. OPPO and OnePlus mobile phones must use USB port for charging, QC4+/QC4.0/PD3.0 and other protocols must use TYPE-C port4. When the USB port and TYPE-C port are plugged into the mobile phone at the same time, both ports are 5V output

Read more less

Overview1. The PCF8563 RTC Board provides the real-time clock/calendar function, which can be driven by a battery on board and works independently even when the MCU is turned off.2. The PCF8563 RTC Board features I2C pinheader on one side, and I2C connector on the opposite side. Hence, its more flexible to connect the board to your development system. The board also supports I2C cascading, allowing the use of multi module connected to the I2C bus at the same time by connecting the pinheader and connector.FeaturesPCF8563, I2C pinheader, I2C connector, 3.3V battery included

Read more less

OverviewThis is an industrial USB to RS232/485/TTL isolated converter with original FT232RL inside. It features embedded protection circuits such as power isolation, ADI magnetical isolation, and TVS diode, etc. Whats more, the USB TO RS232/485/TTL comes with an aluminium alloy enclosure, make it solid and durable to work.The USB TO RS232/485/TTL is very easy to use, fully automatic transceiving without delay. Due to its fast communication, stability, reliability, and safety, it is an ideal choice for industrial control equipments and/or applications with high communication requirement.Features1. USB TO RS232, USB TO RS485, USB TO TTL (UART)2. Adopt original FT232RL, fast communicating, stable and reliable, better compatibility3. Onboard unibody power supply isolation, provides stable isolated voltage, needs no extra power supply for the isolated terminal4. Onboard unibody magnetical isolation, allows signal isolation, high reliability, strong anti-interference, low power consumption5. Onboard TVS (Transient Voltage Suppressor), effectively suppress surge voltage and transient spike voltage in the circuit, lightning-proof & anti-electrostatic6. Onboard self-recovery fuse and protection diodes, ensures the current/voltage stable outputs, provides over-current/over-voltage proof, improves shock resistance7. Fully automatic transceiver circuit with no delay, ensures the USB port communicates with different interfaces fastly and stably, without interfering each other8. Onboard TTL serial 3.3V/5V voltage translator, config the TTL level via switch9. Aluminium alloy enclosure with sand blasting and anodic oxidation, CNC process opening, solid and durable10. 3 LEDs for indicating the power and transceiver status11. High quality USB-B and RS232 connectors, smoothly plug/pullSpecifications1. Product type: industrial optically isolated converter2. Baudrate: 300-921600bps3. Host port: USB4. Device port: RS485/RS232/TTL5. USB:- Operating voltage: 5V- Connector: USB-B- Protection: 200mA self-recovery fuse, isolated output- Transmission distance: ~5m6. RS485:- Connector: screw terminal- Pins: A+, B-, GND- Direction control: hardware automatic control- Protection: 600W lightning-proof and surge-suppress, 15KV ESD protection (reserved 120R balancing resistor solder pads)- Transmission distance: ~1200m- Transmission mode: point-to-multipoints (up to 32 nodes, it is recommended to use repeaters for 16 nodes or more)7. RS232:- Connector: DR9 male- Protection: TVS diode, surge protection, ESD protection- Transmission distance: ~15m- Transmission mode: point-to-point8. TTL (UART):- Operating voltage: 3.3V/5V- Connector: screw terminal- Pins: TXD, RXD, GND- Protection: clamp protection diode, over-voltage/negative-voltage proof, shock resistance- Transmission mode: point-to-point9. LED indicators:- PWR: red power indicator, light up when there is USB connection and voltage is detected- TXD: green TX indicator, light up when the USB port sends data- RXD: blue RX indicator, light up when the device ports send data back10. Operating environment:- Temperature: -15℃ ~ 70℃- Humidity: 5%RH ~ 95%RH11. Operating system: Windows 10 / 8.1 / 8 / 7 / XP12. Package contents:- USB TO RS232/485/TTL x1- USB cable x1

Read more less

OverviewThe USB3300 USB HS Board is an accessory board which acts as the USB high-speed external PHY device for ULPI interface, features the USB3300, MIC2075-1BM onboard.FeaturesUSB3300, MIC2075-1BM, ULPI interface

Read more less

GSM/GPRS/GNSS/Bluetooth HAT for Raspberry Pi, Based on SIM868Overview1. This is a handy, low power Raspberry Pi HAT which features multi communication functionalities: GSM, GPRS, GNSS and Bluetooth.2. It allows your Pi to easily make a telephone call, send messages, connect to wireless Internet, global position, transfer data via Bluetooth, and so on.Features1. Raspberry Pi connectivity, compatible with Raspberry Pi 2B/3B/3B+/Zero/Zero W2. Support SMS, phone call, GPRS, DTMF, HTTP, FTP, MMS, email, etc.3. Support GPS, COMPASS, Glonass, LBS base station positioning, omni-positioning4. Bluetooth 3.0, supports data transferring through Bluetooth5. Onboard USB TO UART converter CP2102 for UART debugging6. 6x LEDs for indicating the module working status7. SIM card slot for 1.8V/3V SIM card8. RTC with backup battery holder9. Baudrate auto detection (1200bps ~115200bps)10. Control via AT commands (3GPP TS 27.007, 27.005, and SIMCOM enhanced AT Commands)11. Support SIM application toolkit: GSM 11.14 Release 9912. Come with development resources and manual (examples for Raspberry Pi/Arduino/STM32)GSM/GPRS1. Band- GSM 850/EGSM 900/DCS 1800/PCS 1900 MHz- Quad-band auto search- Compliant to GSM phase 2/2+2. Emitting power- Class 4 (2W @ GSM 850/EGSM 900 MHz)- Class 1 (1W @ DCS 1800/PCS 1900 MHz)4. GPRS connectivity- GPRS multi-slot class 12 (default)- GPRS multi-slot class 1~12 (configurable)5. GPRS data feature- Downlink speed: max 85.6kbps- Uplink speed: max 85.6kbps- Coding schemes: CS-1\CS-2\CS-3\CS-4- Support PAP (Password Authentication Protocol) for PPP connection- Support PBCCH- Support USSD6. SMS- Support: MT/MO/CB/Text/PDU mode- SMS storage: SIM card7. Audio- Voice encode/decode mode: Half Rate\Full Rate\Enhanced Full Rate\Adaptive muti rate- Support echo cancellation- Support noise reductionGNSS1. Receiver type- 33 tracking channels- 99 acquisition channels- GPS L1 C/A code2. Sensitivity- Tracking: -165 dBm- Cold starts: -148 dBm3. Time-To-First-Fix- Cold starts: 28s (typ.)- Hot starts: < 1s- Warm starts: 26s4. Accuracy- Horizontal position: <2.5m CEPBluetooth1. Integrates AT commands2. Compliant to Bluetooth specification3.0 + EDR3. Support SPP, OPP, HFP/HSP, etc.Misc1. Operating voltage: 5V2. Operating temperature: -40 degree C ~ 85 degree C3. Storage temperature: -45 degree C ~ 90 degree C4. Dimensions: 30.2mm x 65mmWhat is on Board1. SIM868 module2. ZMM5V1: Regulator diode3. SMF05C: TVS diode4. CP2102: USB TO UART converter5. MP1482: Power chip6. NDC7002N: Voltage level translator7. GPS status indicator8. NET indicator:- Flashes fast when the module starts up- Flashes slowly after GSM register succeed9. STA module working status indicator10. SIM868 UART Tx/Rx indicator11. Power indicator12. SIM868 control button: press the button and hold for 1s, to startup/shutdown the SIM86813 .Raspberry Pi GPIO connector14. SIM card slot15. USB TO UART interface16. 3.5mm earphone/mic jack17. GNSS antenna connector18. Bluetooth antenna connector19. GSM antenna connector20. CR1220 battery holder: for RTC backup battery21. UART selection switch- A: Control the SIM868 through USB TO UART- B: Control the SIM868 through Raspberry Pi- C: Access Raspberry Pi through USB TO UARTPackage Contents1. GSM/GPRS/GNSS HAT x12. GSM Antenna x13. GPS External Antenna (B) x14. Bluetooth Antenna x15. USB type A plug to micro plug cable x16. RPi screws pack (2pcs) x1

Read more less

1. Driver chip: SSD13312. Interface: SPI3. Resolution: 96x644. Display size: 0.95 inch5. Colors: 65K colorful6. Visible angle: >160 degree7. Operating temperature: -20~70 degree C8. Storage temperature: -30~80 degree C9. Operating voltage: 3.3V / 5V

Read more less

OverviewThis is a 5.5inch AMOLED display. Compared with LCD, it has advantages of high contrast, wide color gamut, and wide viewing angle, which make it able to bring vivid and delicate visual experience.Features1. 5.5 inch AMOLED, 1080x1920 resolution2. Toughened glass capacitive touch panel, 6H hardness3. Support popular mini PCs such as Raspberry Pi, Jetson Nano, as well as general desktop computers4. When works with Raspberry Pi, supports Raspbian / Ubuntu / Kali / Retropie, driver free5. When works as a computer monitor, support Windows 10/8.1/8/7, five-points touch, and driver free6. 3.5mm audio jack, supports HDMI audio output7. M2.5 screw holes for easy mountingPackage Contents1. 5.5inch HDMI AMOLED x12. HDMI cable x13. USB type A plug to micro B plug cable x14. HDMI adapter (B) x15. USB adapter (B) x16. Screws pack x1

Read more less

Camera module, 2 MegapixelFeatures1. 2 Megapixel2. Array size: UXGA 1622X12003. Power supply: 3.3V4. IO voltage level: 1.7V~3.3V DC5. Output formats:- YUV(422/420)/YCnCr422- RGB565/555- 8-bit compressed data6. Max image transfer rate:- UXGA/SXGA 15fps- UXGA/SXGA 30fps- SVGA 30fps- CIF 60fps

Read more less

Overview1. Sensitive for alcohol, ethanol2. Output voltage boosts along with the concentration of the measured gases increases3. Fast response and recovery4. Adjustable sensitivity5. Signal output indicatorSpecifications1. Power: 2.5V ~ 5.0V2. Dimension: 40.0mm * 21.0mm3. Mounting holes size: 2.0mmApplications1. Car alcohol alarm2. BreathalyserHow to UseIn the case of working with a MCU:1. VCC: 2.5V ~ 5.0V2. GND: Power supply ground3. AOUT: MCU.IO (analog output)4. DOUT: MCU.IO (digital output)Package Contents1. MQ-3 Gas Sensor x12. 4-pin custom connector jumper wire x1

Read more less

Overview1. 49E hall sensor2. Features wide range voltage comparator LM3933. Adjustable sensitivity4. Signal output indicatorSpecifications1. Power: 2.3V ~ 5.3V2. Dimension: 27.0mm * 15.5mm3. Mounting holes size: 2.0mmApplications1. Motor speed measurement2. Object position detection3. Smart car4. Electronic bricksHow to UseIn the case of working with a MCU:1. VCC : 2.3V ~ 5.3V2. GND: Power supply ground3. AOUT : MCU.IO (analog output)4. DOUT: MCU.IO (digital output)

Read more less

1. Micro SD card slot2. Support SDIO and SPI interfaces3. 2.54mm pitch pinheaders

Read more less

RS485 to Ethernet Converter, Easy-to-use, High-speed, Low-power, High-stability, UpgradableOverviewThe RS485 TO ETH module provides an easy way to communicate between RS485 and RJ45 port Ethernet, it can be configured via webpage.Features1. M0 series 32-bit ARM processor, fast speed, high efficiency2. 10/100M Auto-MDI/MDIX ethernet interface, regardless of cross-over or straight-through cable3. Configurable RS485 baudrate (600bps~230.4Kbps), supports five parity check options: None, Odd, Even, Mark, Space4. Available working modes: TCP Server, TCP Client, UDP Server, UDP Client, HTTPD Client (supports GET and POST)5. Configurable via webpage, AT commands, serial protocol, and network protocol, provides configuration protocol which can be integrated to your own software6. Support customized heartbeat packets, make sure the connection is truthful, as well as for actively retrieving sensor data7. Support customized registration packets, auto passing the registered packet as identifier after the connection is established, so that different devices can be distinguished8. Support customized webpage, allows user to customize the module configuration page9. Support RFC2217-like protocol, be able to communicate with devices whose serial setting (baudrate, data bit, etc.) may change10. KeepAlive mechanism, detects broken connection, auto re-connecting11. Support time-out reboot (no-data reboot), ensures a long-term stable connection, configurable reboot time12. Support DNS domain name resolution, configurable DNS server13. Support DHCP, auto-obtained IP or static IP14. Firmware is upgradable via the network15. Restore to factory settings via software and/or hardware16. Comes with default MAC address, which is customizable17. Provided software: module configuration software, TCP/UDP testing tool, VCOM virtual serial port software18. Example code: host computer (socket ), VB, C++, Delphi, Android, iOS, etc.Specifications1. Ethernet:- Connector: 4-pin RJ45- Communication rate: 10/100Mbps- Interface protection: 1.5KV electromagnetic isolation- Protocols: IP, TCP, UDP, ARP, ICMP, DHCP, DNS, HTTPD Client- TX cache: 6Kbyte- RX cache: 4Kbyte2. RS485:- Connector: screw terminal (A+, B-, GND)- Data bit: 5bit, 6bit, 7bit, 8bit- Stop bit: 1, 2- Parity bit: None, Odd, Even, Mark, Space- Baudrate: 600bps~230.4Kbps- RX cache: 800byte- Hardware flow control: none- Interface protection:- 2KV ESD protection- RS485 pull up/down registers: 2.2KΩ3. Power:- Power supply: 5.0~7.0V (5V recommended)- Operating current: 150mA (@5V)- Power consumption: <1W- Interface protection: reverse-proof, ESD protection, anti-surge4. Environment:- Operating temperature: -25~75 degree C- Storage temperature: -40~105 degree C5. Size: 69.65*63.59*25.47mmPackage Contents1. RS485 TO ETH x12. 5V power adapter x1

Read more less

Features1. Supports NVIDIA Jetson Nano Developer Kit2. Supports night vision when works with infrared LEDs3. 8 Megapixels4. Sensor: IMX2195. Resolution: 3280 × 24646. Lens specifications:- CMOS size: 1/4inch- Aperture (F): 2.0- Focal Length: 2.96mm- Angle of View (diagonal): 77 degree- Distortion: <1%- Lens dimensions: 6.5mm × 6.5mm7. 4 screw holes8. Used for attachment9. Provides 3.3V power output10. Supports connecting infrared LED and/or fill flash LED11. Dimension: 25mm x 24mm12. Weight: 31gPacking List1. IMX219-77IR Camera x12. Infrared LED Board (B) 2PCS x13. 15-pin FFC (opposite sides contact) x1

Read more less

OverviewThe RPi Relay Board (B) is an expansion board with 8-ch relays for Raspberry Pi. It gives your Pi the ability to control high voltage products such as home appliances.Features1. Supports Raspberry Pi A+/B+/2B/3B/3B+2. High quality relays, loads up to 5A 250V AC or 5A 30V DC3. Photo coupling isolation, prevent interference from high voltage circuit4. Standard rail mount bottom case5. Onboard LEDs for indicating relays status6. Relay control pin selection jumper, allows to control the relays by custom pins other than the default pins7. Reserved control Interface, allows to work with controllers like PLC8. Comes with development resources, including examples in wiringPi, bcm2835, python, python-bottle (webpage control), and crontab (cron job)Specifications1. Power supply voltage: 5V2. Trigger signal: 3.3V/5V3. Relay channels: 8-ch4. Contact form: SPDT-NO,NC5. Closed current: 6mA (per channel)6. Connector: screw terminal block7. Dimension: 232 × 72 (mm)8. Mounting hole size: 3.0mm

Read more less

OverviewSpeaker expansion module designed for micro:bit, makes your micro:bit become a music player easily.Furthermore, it can also be used for Arduino development, compatible with 3.3V/5V Arduino boards.Features1. Onboard Hi-Fi chip NS80022. Sound volume adjustment3. Earphone jack output4. Comes with development resources (micro:bit graphical demo/python code/Arduino demo/user manual, etc.)Specifications1. Operating voltage: 2.0V ~ 5.5V2. Dimension: 36.52mm x 43.44mm3. Through holes diameter: 3.2mm

Read more less

OverviewThis solar power management module is designed for 6V~24V solar panel. It can charge the 3.7V Li battery through solar panel or USB connection, and provides 5V/1A regulated output.The module features MPPT (Maximum Power Point Tracking) function and multi protection circuits, therefore, it is able to keep working with high-efficiency, stability, and safety. It is suited for solar powered, low-power IoT, and other environmental protection projects.Features1. Supports MPPT (Maximum Power Point Tracking) function, maximizing the efficiency of the solar panel2. Supports solar panel / USB connection battery charging3. For 6V~24V solar panel, DC-002 jack input or screw terminal input4. Onboard MPPT SET switch, select the level closed to input level to improve charging efficiency5. Two 5V output interfaces: pinheaders and USB port6. Onboard high capacity aluminum electrolytic capacitor and SMD ceramic capacitor, reducing the ripple, stable performance7. 14500 battery holder and PH2.0 battery connector, for connecting multi kinds of 3.7V Li battery8. Several LED indicators, for monitoring the status of solar panel and battery9. Multi protection circuits: over charge / over discharge / reverse protection / over heat / over current, stable and safe to useSpecifications1. Solar panel input voltage (SOLAR IN): 6V~24V2. Micro USB input voltage (USB IN): 5V3. Pinheader / USB output (USB OUT): 5V 1A4. Charging cutoff voltage: 4.2V+/-1％5. Over discharging protection voltage: 2.9V+/-1％6. Solar panel charge efficiency: ~78%7. USB charge efficiency: ~82%8. 3.7V battery boost output efficiency: ~86%9. Max quiescent current: <2mA10. Operating temperature: -40~85C11. Dimension: 65.2mm x 56.2mm x 22.9mm

Read more less

Features1. Resistive touch screen TFT LCD, 4inch, 480x320 resolution2. Standard Arduino interface, compatible with development boards like : Arduino UNO, Leonardo, UNO PLUS, NUCLEO, XNUCLEO3. Onboard stand-alone touch controller, better touching than solutions that use AD pins directly for touch control4. PWM backlight control, allows to adjust the backlight to a comfortable level5. Micro SD slot, provides an easy way to store photos for displaying6. Controlled via SPI, only a few Arduino pins are used7. Comes with STM32 and Arduino examples, convenient for portingKey Parameters1. LCD Type: TFT2. LCD Interface: SPI3. LCD Controller: ILI94864. Touch Screen Type: Resistive5. Touch Screen Controller: XPT20466. Colors: RGB, 65K colors7. Resolution: 480x320 (Pixel)8. Aspect Ratio: 8:59. I/O Voltage: 3.3V/5VWiki : www.waveshare.com/wiki/4inch_TFT_Touch_Shield

Read more less

OverviewArduino is a massive ecosystem, if there is a way for the Raspberry Pi GPIO interface to adapt to Arduino pinouts, it is possible to use the Pi together with vast Arduino shields and hardware/software resources. The ARPI600 is just intended for this.What is more, the ARPI600 also support XBee modules, make it easy to add wireless feature to your great project.Supported Pi1. Raspberry Pi 1 Model A+2. Raspberry Pi 1 Model B+3. Raspberry Pi 2 Model B4. Raspberry Pi 3 Model B5. Raspberry Pi 3 Model B+ARPI600 Features1. Compatible with Arduino UNO, Leonardo, easy to connect with various Arduino shields2. XBee connector for connecting various XBee modules3. Sensor interface for connecting various sensors4. Onboard USB TO UART for serial port debugging, also can be configured as XBee USB adapter5. Onboard ADC, 10 bit, 38KSPS, 11 channels (6 channels for Arduino interface, 5 channels for sensors)6. Onboard RTCWhat is on the ARPI6001. Arduino connector: For connecting Arduino shields2. ICSP interface: Arduino ICSP3. XBee connector: For connecting XBee communication modules4. Sensor interface: For connecting sensors5. Raspberry Pi connector: For connecting Raspberry Pi6. USB TO UART7. TLC1543: AD converter8. PCF8563: RTC9. CP210210. 32.768KHz crystal: For RTC11. Power indicator12. XBee state LED13. XBee and Arduino interface RESET button14. XBee EASYLINK button15. RTC battery holder: For CR1220 button battery16. TLC1543 reference voltage configuration jumper17. RTC jumper18. UART jumper- When connecting P_RX and CP_TX, P_TX and CP_RX respectively, USB TO UART is connected to Raspberry Pi serial port- When connecting XB_RX and CP_TX, XB_TX and CP_RX respectively, USB TO UART is connected to XBee serial port- When connecting XB_RX and P_TX, XB_TX and P_RX respectively, Raspberry Pi serial port is connected to XBee serial port19. Arduino AD selection jumper- Short 2 and 3: Arduino A0-A5 as AD input- Short 1 and 2: Arduino A0-A5 as digital control20. Arduino I2C selection jumper- Short the jumper : Arduino A4-A5 as I2C control (the A4-A5 of Arduino AD selection jumper should be opened)21. Arduino SPI selection jumper- Short 1 and 2: Arduino D11-D13 as SPI control (default)- Short 2 and 3: Arduino D11-D13 as digital controlPackage Contents1. ARPI600 x 12. USB type A plug to mini-B plug cable x 13. RPi screws pack (2pcs) x 1

Read more less

DescriptionMini ST-LINK/V2 on a small single board, an extreme low cost solution for in-circuit debugger/programmer for STM8 and STM32.Features1. Onboard 500mA self-recovery fuse to avoid harming by short circuit2. Dual voltage output (3.3V/5V), easy for debugging/programming3. Standard USB interface for direct connection to PC4. Debugging/Programing performance- Debugging : run at full-speed, single-stepped, breakpoints, viewing variables and registers, etc.- Programming : supports FLASH ROM, EEPROM, AFR, etc.- USB2.0 combined with SWIM/SWD interfaces : quick response for debugging & fast speed for programming5. Upgradable firmware- The firmware is upgradable to support more devices in the future- Automatically upgraded6. Supported software- ST-LINK Utility v2.0 (or higher ver.)- STVD Version 4.2.1 (or higher ver.)- STVP Version 3.2.3 (or higher ver.)- IAR EWARM Revision v6.20 (or higher ver.)- IAR EWSTM8 Revision v1.30 (or higher ver.)- KEIL RVMDK Revision v4.21 (or higher ver.)- ATOLLIC- TASKING7. Supported devices- All the STM8 devices with SWIM interface- All the STM32 devices with SWD interfacePackage Contents1. ST-LINK/V2 (mini) × 12. 4-pin custom connector cable × 13. USB type A plug to receptacle cable × 1

Read more less