Microwave Radar Human Body Sensor Switch Detection Module(RCWL-0516)

Description


1. Sensing distance: about 3-5 meters
2. Using Doppler radar technology, a microwave sensor module that specifically detects object movement
3. The module has the characteristics of high sensitivity, long sensing distance, strong reliability, large sensing angle, wide power supply voltage range, etc.
4. Widely used in various occasions such as human body induction lighting and anti-theft alarm
5. Adopt special signal processing control chip RCWL-9196
6. Wide working voltage range: 4.0~28.0V
7. Compared with traditional infrared induction PIR, it has penetrating detection ability
8. Blocking time, adjustable distance
9. Can output 3. 3V power supply

Pin function description:
1. 3.3V output voltage, drive current 100mA
2. GND module ground
3. OUT controls the signal output. When there is an object moving in the detection area, OUT outputs a high level; C-TM can set the repeated trigger time. If there is a trigger signal (there is an object moving) within the repeated trigger time, it will continue to output a high level. ;If there is no moving object in the detection area, output low level
4. VIN module power input, 4-28V
5. CDS trigger control signal; less than 0.7V, OUT always outputs low level; greater than 0.7V, the detection works normally, the CDS pin is connected with a photoresistor, and the module detection function can be turned off at night

Adjustment Section Instructions:
1. C-TM: Adjust the repeated trigger time, the default trigger time is 2S, increasing the capacitor capacity will increase the repeated trigger time, the actual calculation of the repeated trigger time can be done as follows, put a capacitor on the C-TM, and test the frequency f of pin 3 of 9196 , repeated trigger time T= (1/f) *32768
2. R-GN detection distance adjustment, connected to a resistor, the detection distance becomes smaller, not connected, the detection distance is about 7m, connected to a 1m resistor, the detection distance is about 5m, the customer can adjust according to the actual situation
3. The internal VCC of R-CDS is connected in parallel with the internal 1m resistor to the CDS pin (that is, 9 pin 9196) through the R-CDS. The CDS is connected to the photoresistor, and the module detection function can be turned off at night, and R can be set according to the actual ambient brightness. -CDS value

Attention should be paid to the application design:
1. There must be no metal shielding in front of the sensing surface
2. There should be more than 1CM space reserved at the front and back of the sensing surface
3. The module is as parallel as possible to the plane of the mounting carrier
4. The application is effective in a certain detection area
5. The component side of the module is the positive sensing side, and the reverse side is the negative sensing side, and the negative sensing side has a slightly poorer sensing effect
6. Microwave modules cannot be used on a large scale in the same area, otherwise there will be mutual interference, and the distance between individual bodies is greater than 1M

Microwave Radar Human Body Sensor Switch Detection Module(RCWL-0516)

Product form

SKU: TBD0603960801A

  • In stock (Processing Time 1 - 72 hours)

€3,63

    • Guaranteed secure & safe checkout.

    Icon for truckShipping Methods

    To find out all available shipping methods, and the exact delivery time add the product to the cart and verify it using our shipping calculator.

    Icon for 24_hour_clockOrder Processing Time

    All orders are shipped within a maximum of 72 hours from the order's arrival.

    Icon for coinMoney Back Guarantee

    Garmade Money Back Guarantee- Get the item you ordered or your money back, it's that simple.

    Icon for image_placeholderMismatched Product

    Product doesn't match the description? Contact us within 31 days after you receive it!

    Icon for mobile_paymentRefunds

    In case of cancellation, money will be refunded to your account within 14 days.

    Description


    1. Sensing distance: about 3-5 meters
    2. Using Doppler radar technology, a microwave sensor module that specifically detects object movement
    3. The module has the characteristics of high sensitivity, long sensing distance, strong reliability, large sensing angle, wide power supply voltage range, etc.
    4. Widely used in various occasions such as human body induction lighting and anti-theft alarm
    5. Adopt special signal processing control chip RCWL-9196
    6. Wide working voltage range: 4.0~28.0V
    7. Compared with traditional infrared induction PIR, it has penetrating detection ability
    8. Blocking time, adjustable distance
    9. Can output 3. 3V power supply

    Pin function description:
    1. 3.3V output voltage, drive current 100mA
    2. GND module ground
    3. OUT controls the signal output. When there is an object moving in the detection area, OUT outputs a high level; C-TM can set the repeated trigger time. If there is a trigger signal (there is an object moving) within the repeated trigger time, it will continue to output a high level. ;If there is no moving object in the detection area, output low level
    4. VIN module power input, 4-28V
    5. CDS trigger control signal; less than 0.7V, OUT always outputs low level; greater than 0.7V, the detection works normally, the CDS pin is connected with a photoresistor, and the module detection function can be turned off at night

    Adjustment Section Instructions:
    1. C-TM: Adjust the repeated trigger time, the default trigger time is 2S, increasing the capacitor capacity will increase the repeated trigger time, the actual calculation of the repeated trigger time can be done as follows, put a capacitor on the C-TM, and test the frequency f of pin 3 of 9196 , repeated trigger time T= (1/f) *32768
    2. R-GN detection distance adjustment, connected to a resistor, the detection distance becomes smaller, not connected, the detection distance is about 7m, connected to a 1m resistor, the detection distance is about 5m, the customer can adjust according to the actual situation
    3. The internal VCC of R-CDS is connected in parallel with the internal 1m resistor to the CDS pin (that is, 9 pin 9196) through the R-CDS. The CDS is connected to the photoresistor, and the module detection function can be turned off at night, and R can be set according to the actual ambient brightness. -CDS value

    Attention should be paid to the application design:
    1. There must be no metal shielding in front of the sensing surface
    2. There should be more than 1CM space reserved at the front and back of the sensing surface
    3. The module is as parallel as possible to the plane of the mounting carrier
    4. The application is effective in a certain detection area
    5. The component side of the module is the positive sensing side, and the reverse side is the negative sensing side, and the negative sensing side has a slightly poorer sensing effect
    6. Microwave modules cannot be used on a large scale in the same area, otherwise there will be mutual interference, and the distance between individual bodies is greater than 1M

    Additional Information

    Icon for truckShipping Info

    IMPORTANT INFO - PLEASE CHECK BEFORE ORDERING.



      Estimated transit time and postage fee depends on the method you choose at checkout. Please add the desired product to the cart and there you will be able to see all this information.

      Complete and right address is the guarantee of fast and efficient delivery, so please kindly recheck it when you place an order.

      In order to ensure a fast and efficient delivery, we need to have the method of contact with you. Email and Phone Number is a very important detail and must be accurate. All orders with an incorrect email or phone number will be canceled immediately.

      We strive to dispatch all orders within 72 hours of placing your order. But sometimes if the order is big or the products are more sophisticated, it can take a little longer. As soon as we dispatched it, you will receive a confirmation email along with a tracking number.

      Please be aware that sometimes due to unclear address, hard to access, no answer at address, the package can be kept at your local post office for collection. In this case you will be informed by the delivery company and by us. Please also monitor the tracking number.

      For European Union Countries:
    - If your order is less than 150€ excluding shipping costs, then the Taxes are already included in the price. This means that there will be NO extra charge upon delivery.
    - If your order is more than 150€, you will NOT be charged Taxes at the checkout, and you will have to pay upon delivery based on your local VAT rate.

     

    Icon for reviewReviews

    Customer Reviews

    Be the first to write a review
    0%
    (0)
    0%
    (0)
    0%
    (0)
    0%
    (0)
    0%
    (0)

    Login

    Forgot your password?

    Don't have an account yet?
    Create account