Waveshare Compute Module IO Board Plus for Raspberry Pi CM3 / CM3L / CM3+ / CM3+L

Description

Overview
The Compute Module IO Board Plus is a development board which you can plug a Raspberry Pi Compute Module into, and make use of the resources of Pi more flexibly. It is compatible with the Compute Module IO Board V3 from the Raspberry Pi Foundation, along with various common use components.

Compute Module IO Board Plus Features
1. Compatible with the Compute Module IO Board V3 from the Raspberry Pi Foundation
2. Raspberry Pi GPIO header, for connecting sorts of Raspberry Pi HATs
3. Arduino connectivity, also supports Arduino shields
4. 1-WIRE interface, for connecting single-bus devices like DS18B20
5. 4x keys, 4x LEDs, 1x Buzzer, for I/O testing
6. Onboard USB HUB, allows connecting more USB devices
7. IR receiver, IR remote control is available
8. Onboard USB TO UART, for serial debugging
9. Sensor interface
10. 10-bit ADC, 38KSPS, 11-ch (6-ch for Arduino interface, 5-ch for sensors)
11. 16-bit DAC, 2-ch
12. Onboard RTC, one of the most common and useful functions

What is on the Compute Module IO Board Plus
1. Compute Module interface: for connecting Compute Module (CM3 / CM3L / CM3+ / CM3+L)
2. Compute Module GPIO header: breakout all the Compute Module pins
3. Raspberry Pi GPIO header: for connecting Raspberry Pi HATs
4. CSI interface: camera ports, for connecting Raspberry Pi Camera
5. DSI interface: display ports, for connecting Raspberry Pi LCD
6. HDMI port
7. USB ports: for connecting USB devices
8. USB SLAVE interface: allows you to burn system image in to Compute Module 3
9. USB TO UART interface: for serial debugging
10. Arduino header: for connecting Arduino shields
11. AD/DA input/output screw terminals
12. 1-WIRE interface: for connecting single-bus devices like DS18B20
13. Sensor interface
14. Power port: 5V 2.5A
15. FE1.1S: USB HUB chip
16. 12MHz crystal
17. CP2102: USB TO UART converter
18. Micro SD card slot: Insert a Micro SD card with pre-burnt system, to start up Compute Module 3 Lite
19. TLC1543: AD converter
20. DAC8552: 16-bit DAC, 2-ch
21. DS3231: High-precision RTC chip, I2C interface
22. RTC battery holder: supports CR1220 batteries
23. Voltage regulator: 3.3V / 2.5V / 1.8V
24. LFN0038K: IR receiver
25. Buzzer
26. Power indicator
27. ACT indicator: indicating the Micro SD card status
28. User LEDs
29. User Keys
30. BOOT selection
- EN: enable the PC to access SD card/eMMC through USB SLAVE
- DIS: the Compute Module will boot from SD card/eMMC
31. VGx power selection: config the I/O level
32. USB HUB enable jumper: HUB enable and USB SLAVE power selection
33. ADC/DAC configuration: config the power supply and reference voltage of ADC/DAC
34. Peripheral configuration: config the control pins of UART, user keys, user LEDs, 1-WIRE interface, IR receiver, and buzzer
35. Arduino AD selection
- Connect 1 and 2: Arduino A0-A5 as digital control pin
- Connect 2 and 3: Arduino A0-A5 as AD input

Waveshare Compute Module IO Board Plus for Raspberry Pi CM3 / CM3L / CM3+ / CM3+L

Product form

SKU: ZY14058780

  • In stock (Processing Time 1 - 72 hours)

€127,68

    • Guaranteed secure & safe checkout.

    Icon for truckShipping Methods

    To find out all available shipping methods, and the exact delivery time add the product to the cart and verify it using our shipping calculator.

    Icon for 24_hour_clockOrder Processing Time

    All orders are shipped within a maximum of 72 hours from the order's arrival.

    Icon for coinMoney Back Guarantee

    Garmade Money Back Guarantee- Get the item you ordered or your money back, it's that simple.

    Icon for image_placeholderMismatched Product

    Product doesn't match the description? Contact us within 31 days after you receive it!

    Icon for mobile_paymentRefunds

    In case of cancellation, money will be refunded to your account within 14 days.

    Description

    Overview
    The Compute Module IO Board Plus is a development board which you can plug a Raspberry Pi Compute Module into, and make use of the resources of Pi more flexibly. It is compatible with the Compute Module IO Board V3 from the Raspberry Pi Foundation, along with various common use components.

    Compute Module IO Board Plus Features
    1. Compatible with the Compute Module IO Board V3 from the Raspberry Pi Foundation
    2. Raspberry Pi GPIO header, for connecting sorts of Raspberry Pi HATs
    3. Arduino connectivity, also supports Arduino shields
    4. 1-WIRE interface, for connecting single-bus devices like DS18B20
    5. 4x keys, 4x LEDs, 1x Buzzer, for I/O testing
    6. Onboard USB HUB, allows connecting more USB devices
    7. IR receiver, IR remote control is available
    8. Onboard USB TO UART, for serial debugging
    9. Sensor interface
    10. 10-bit ADC, 38KSPS, 11-ch (6-ch for Arduino interface, 5-ch for sensors)
    11. 16-bit DAC, 2-ch
    12. Onboard RTC, one of the most common and useful functions

    What is on the Compute Module IO Board Plus
    1. Compute Module interface: for connecting Compute Module (CM3 / CM3L / CM3+ / CM3+L)
    2. Compute Module GPIO header: breakout all the Compute Module pins
    3. Raspberry Pi GPIO header: for connecting Raspberry Pi HATs
    4. CSI interface: camera ports, for connecting Raspberry Pi Camera
    5. DSI interface: display ports, for connecting Raspberry Pi LCD
    6. HDMI port
    7. USB ports: for connecting USB devices
    8. USB SLAVE interface: allows you to burn system image in to Compute Module 3
    9. USB TO UART interface: for serial debugging
    10. Arduino header: for connecting Arduino shields
    11. AD/DA input/output screw terminals
    12. 1-WIRE interface: for connecting single-bus devices like DS18B20
    13. Sensor interface
    14. Power port: 5V 2.5A
    15. FE1.1S: USB HUB chip
    16. 12MHz crystal
    17. CP2102: USB TO UART converter
    18. Micro SD card slot: Insert a Micro SD card with pre-burnt system, to start up Compute Module 3 Lite
    19. TLC1543: AD converter
    20. DAC8552: 16-bit DAC, 2-ch
    21. DS3231: High-precision RTC chip, I2C interface
    22. RTC battery holder: supports CR1220 batteries
    23. Voltage regulator: 3.3V / 2.5V / 1.8V
    24. LFN0038K: IR receiver
    25. Buzzer
    26. Power indicator
    27. ACT indicator: indicating the Micro SD card status
    28. User LEDs
    29. User Keys
    30. BOOT selection
    - EN: enable the PC to access SD card/eMMC through USB SLAVE
    - DIS: the Compute Module will boot from SD card/eMMC
    31. VGx power selection: config the I/O level
    32. USB HUB enable jumper: HUB enable and USB SLAVE power selection
    33. ADC/DAC configuration: config the power supply and reference voltage of ADC/DAC
    34. Peripheral configuration: config the control pins of UART, user keys, user LEDs, 1-WIRE interface, IR receiver, and buzzer
    35. Arduino AD selection
    - Connect 1 and 2: Arduino A0-A5 as digital control pin
    - Connect 2 and 3: Arduino A0-A5 as AD input

    Additional Information

    Icon for truckShipping Info

    IMPORTANT INFO - PLEASE CHECK BEFORE ORDERING.



      Estimated transit time and postage fee depends on the method you choose at checkout. Please add the desired product to the cart and there you will be able to see all this information.

      Complete and right address is the guarantee of fast and efficient delivery, so please kindly recheck it when you place an order.

      In order to ensure a fast and efficient delivery, we need to have the method of contact with you. Email and Phone Number is a very important detail and must be accurate. All orders with an incorrect email or phone number will be canceled immediately.

      We strive to dispatch all orders within 72 hours of placing your order. But sometimes if the order is big or the products are more sophisticated, it can take a little longer. As soon as we dispatched it, you will receive a confirmation email along with a tracking number.

      Please be aware that sometimes due to unclear address, hard to access, no answer at address, the package can be kept at your local post office for collection. In this case you will be informed by the delivery company and by us. Please also monitor the tracking number.

      For European Union Countries:
    - If your order is less than 150€ excluding shipping costs, then the Taxes are already included in the price. This means that there will be NO extra charge upon delivery.
    - If your order is more than 150€, you will NOT be charged Taxes at the checkout, and you will have to pay upon delivery based on your local VAT rate.

     

    Icon for reviewReviews

    Customer Reviews

    No reviews yet
    0%
    (0)
    0%
    (0)
    0%
    (0)
    0%
    (0)
    0%
    (0)

    Login

    Forgot your password?

    Don't have an account yet?
    Create account